upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/include/status_led.h

103 lines
3.0 KiB

/*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* The purpose of this code is to signal the operational status of a
* target which usually boots over the network; while running in
* PCBoot, a status LED is blinking. As soon as a valid BOOTP reply
* message has been received, the LED is turned off. The Linux
* kernel, once it is running, will start blinking the LED again,
* with another frequency.
*/
#ifndef _STATUS_LED_H_
#define _STATUS_LED_H_
#ifdef CONFIG_LED_STATUS
#define LED_STATUS_PERIOD (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ)
#ifdef CONFIG_LED_STATUS1
#define LED_STATUS_PERIOD1 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ1)
#endif /* CONFIG_LED_STATUS1 */
#ifdef CONFIG_LED_STATUS2
#define LED_STATUS_PERIOD2 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ2)
#endif /* CONFIG_LED_STATUS2 */
#ifdef CONFIG_LED_STATUS3
#define LED_STATUS_PERIOD3 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ3)
#endif /* CONFIG_LED_STATUS3 */
#ifdef CONFIG_LED_STATUS4
#define LED_STATUS_PERIOD4 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ4)
#endif /* CONFIG_LED_STATUS4 */
#ifdef CONFIG_LED_STATUS5
#define LED_STATUS_PERIOD5 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ5)
#endif /* CONFIG_LED_STATUS5 */
void status_led_init(void);
void status_led_tick (unsigned long timestamp);
void status_led_set (int led, int state);
/***** MVS v1 **********************************************************/
#if (defined(CONFIG_MVS) && CONFIG_MVS < 2)
# define STATUS_LED_PAR im_ioport.iop_pdpar
# define STATUS_LED_DIR im_ioport.iop_pddir
# undef STATUS_LED_ODR
# define STATUS_LED_DAT im_ioport.iop_pddat
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
/***** Someone else defines these *************************************/
#elif defined(STATUS_LED_PAR)
/*
* ADVICE: Define in your board configuration file rather than
* filling this file up with lots of custom board stuff.
*/
#elif defined(CONFIG_LED_STATUS_BOARD_SPECIFIC)
/* led_id_t is unsigned long mask */
typedef unsigned long led_id_t;
extern void __led_toggle (led_id_t mask);
extern void __led_init (led_id_t mask, int state);
extern void __led_set (led_id_t mask, int state);
void __led_blink(led_id_t mask, int freq);
#else
# error Status LED configuration missing
#endif
/************************************************************************/
#ifndef CONFIG_LED_STATUS_BOARD_SPECIFIC
# include <asm/status_led.h>
#endif
#endif /* CONFIG_LED_STATUS */
/*
* Coloured LEDs API
*/
#ifndef __ASSEMBLY__
void coloured_LED_init(void);
void red_led_on(void);
void red_led_off(void);
void green_led_on(void);
void green_led_off(void);
void yellow_led_on(void);
void yellow_led_off(void);
void blue_led_on(void);
void blue_led_off(void);
#else
.extern LED_init
.extern red_led_on
.extern red_led_off
.extern yellow_led_on
.extern yellow_led_off
.extern green_led_on
.extern green_led_off
.extern blue_led_on
.extern blue_led_off
#endif
#endif /* _STATUS_LED_H_ */