upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
2.9 KiB
2.9 KiB
This file contains information for VSC9953, a Vitesse L2 Switch IP
which is integrated in the T1040/T1020 Freescale SoCs.
About Device:
=============
VSC9953 is an 8-port Gigabit Ethernet switch supports the following features:
- 8192 MAC addresses
- Static Address provisioning
- Dynamic learning of MAC addresses and aging
- 4096 VLANs
- Independent and shared VLAN learning (IVL, SVL)
- Policing with storm control and MC/BC protection
- IPv4 and IPv6 multicast
- Jumbo frames (9.6 KB)
- Access Control List
- VLAN editing, translation and remarking
- RMON counters per port
Switch interfaces:
- 8 Gigabit switch ports (ports 0 to 7) are external and are connected to external PHYs
- 2 switch ports (ports 8 and 9) of 2.5 G are connected (fixed links)
to FMan ports (FM1@DTSEC1 and FM1@DTSEC2)
Commands Overview:
=============
Commands supported
- enable/disable a port or show its configuration (speed, duplexity, status, etc.)
- port statistics
- MAC learning
- add/remove FDB entries
- Port-based VLAN
- Private/Shared VLAN learning
- VLAN ingress filtering
- Port LAG
Commands syntax
ethsw [port <port_no>] { enable | disable | show } - enable/disable a port; show a port's configuration
ethsw [port <port_no>] statistics { [help] | [clear] } - show an l2 switch port's statistics
ethsw [port <port_no>] learning { [help] | show | auto | disable } - enable/disable/show learning configuration on a port
ethsw [port <port_no>] [vlan <vid>] fdb { [help] | show | flush | { add | del } <mac> } - add/delete a mac entry in FDB; use show to see FDB entries;
if [vlan <vid>] is missing, VID 1 will be used
ethsw [port <port_no>] pvid { [help] | show | <pvid> } - set/show PVID (ingress and egress VLAN tagging) for a port
ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> } - add a VLAN to a port (VLAN members)
ethsw [port <port_no>] untagged { [help] | show | all | none | pvid } - set egress tagging mode for a port
ethsw [port <port_no>] egress tag { [help] | show | pvid | classified } - configure VID source for egress tag.
Tag's VID could be the frame's classified VID or the PVID of the port
ethsw vlan fdb { [help] | show | shared | private } - make VLAN learning shared or private
ethsw [port <port_no>] ingress filtering { [help] | show | enable | disable } - enable/disable VLAN ingress filtering on port
ethsw [port <port_no>] aggr { [help] | show | <lag_group_no> } - get/set LAG group for a port
=> ethsw show
Port Status Link Speed Duplex
0 enabled down 10 half
1 enabled down 10 half
2 enabled down 10 half
3 enabled up 1000 full
4 disabled down - half
5 disabled down - half
6 disabled down - half
7 disabled down - half
8 enabled up 2500 full
9 enabled up 2500 full
=>