upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/palmtreo680/palmtreo680.c

148 lines
3.7 KiB

/*
* Palm Treo 680 Support
*
* Copyright (C) 2013 Mike Dunn <mikedunn@newsguy.com>
*
* This file is released under the terms of GPL v2 and any later version.
* See the file COPYING in the root directory of the source tree for details.
*
*/
#include <common.h>
#include <command.h>
#include <serial.h>
#include <nand.h>
#include <malloc.h>
#include <asm/arch/pxa-regs.h>
#include <asm/arch-pxa/pxa.h>
#include <asm/arch-pxa/regs-mmc.h>
#include <asm/io.h>
#include <asm/global_data.h>
#include <u-boot/crc.h>
#include <linux/mtd/docg4.h>
DECLARE_GLOBAL_DATA_PTR;
static struct nand_chip docg4_nand_chip;
int board_init(void)
{
/* We have RAM, disable cache */
dcache_disable();
icache_disable();
gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
gd->bd->bi_boot_params = CONFIG_SYS_DRAM_BASE + 0x100;
return 0;
}
int dram_init(void)
{
/* IPL initializes SDRAM (we're already running from it) */
gd->ram_size = PHYS_SDRAM_1_SIZE;
return 0;
}
#ifdef CONFIG_LCD
void lcd_enable(void)
{
/*
* Undo the L_BIAS / gpio77 pin configuration performed by the pxa lcd
* driver code. We need it as an output gpio.
*/
writel((readl(GAFR2_L) & ~(0xc << 24)), GAFR2_L);
/* power-up and enable the lcd */
writel(0x00400000, GPSR(86)); /* enable; drive high */
writel(0x00002000, GPSR(77)); /* power; drive high */
writel(0x02000000, GPCR(25)); /* enable_n; drive low */
/* turn on LCD backlight and configure PWM for reasonable brightness */
writel(0x00, PWM_CTRL0);
writel(0x1b1, PWM_PERVAL0);
writel(0xfd, PWM_PWDUTY0);
writel(0x00000040, GPSR(38)); /* backlight power on */
}
#endif
#ifdef CONFIG_MMC
int board_mmc_init(bd_t *bis)
{
writel(1 << 10, GPSR(42)); /* power on */
return pxa_mmc_register(0);
}
#endif
void board_nand_init(void)
{
/* we have one 128M diskonchip G4 */
struct mtd_info *mtd = &nand_info[0];
struct nand_chip *nand = &docg4_nand_chip;
if (docg4_nand_init(mtd, nand, 0))
hang();
}
#ifdef CONFIG_SPL_BUILD
void nand_boot(void)
{
__attribute__((noreturn)) void (*uboot)(void);
extern const void *_start, *_end; /* boundaries of spl in memory */
/* size of spl; ipl loads this, and then a portion of u-boot */
const size_t spl_image_size = ((size_t)&_end - (size_t)&_start);
/* the flash offset of the blocks that are loaded by the spl */
const uint32_t spl_load_offset = CONFIG_SYS_NAND_U_BOOT_OFFS +
DOCG4_IPL_LOAD_BLOCK_COUNT * DOCG4_BLOCK_SIZE;
/* total number of bytes loaded by IPL */
const size_t ipl_load_size =
DOCG4_IPL_LOAD_BLOCK_COUNT * DOCG4_BLOCK_CAPACITY_SPL;
/* number of bytes of u-boot proper that was loaded by the IPL */
const size_t ipl_uboot_load_size = ipl_load_size - spl_image_size;
/* number of remaining bytes of u-boot that the SPL must load */
const size_t spl_load_size =
CONFIG_SYS_NAND_U_BOOT_SIZE - ipl_load_size;
/* memory address where we resume loading u-boot */
void *const load_addr =
(void *)(CONFIG_SYS_NAND_U_BOOT_DST + ipl_uboot_load_size);
/*
* Copy the portion of u-boot already read from flash by the IPL to its
* correct load address.
*/
memcpy((void *)CONFIG_SYS_NAND_U_BOOT_DST, &_end, ipl_uboot_load_size);
/*
* Resume loading u-boot where the IPL left off.
*/
nand_spl_load_image(spl_load_offset, spl_load_size, load_addr);
#ifdef CONFIG_NAND_ENV_DST
nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
(void *)CONFIG_NAND_ENV_DST);
#ifdef CONFIG_ENV_OFFSET_REDUND
nand_spl_load_image(CONFIG_ENV_OFFSET_REDUND, CONFIG_ENV_SIZE,
(void *)CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE);
#endif
#endif
/*
* Jump to U-Boot image
*/
uboot = (void *)CONFIG_SYS_NAND_U_BOOT_START;
(*uboot)();
}
void board_init_f(ulong bootflag)
{
nand_boot();
}
#endif /* CONFIG_SPL_BUILD */