upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/xes/xpedite1000
Masahiro Yamada 461be2f96e kconfig: remove redundant "string" type in arch and board Kconfigs 10 years ago
..
Kconfig kconfig: remove redundant "string" type in arch and board Kconfigs 10 years ago
MAINTAINERS Add board MAINTAINERS files 10 years ago
Makefile board: powerpc: convert makefiles to Kbuild style 11 years ago
README
config.mk Add GPL-2.0+ SPDX-License-Identifier to source files 11 years ago
init.S Add GPL-2.0+ SPDX-License-Identifier to source files 11 years ago
u-boot.lds.debug Add GPL-2.0+ SPDX-License-Identifier to source files 11 years ago
xpedite1000.c Add GPL-2.0+ SPDX-License-Identifier to source files 11 years ago

README

			   XES XPedite1000 Board

Last Update: December 29, 2003
=======================================================================

This file contains some handy info regarding U-Boot and the XES
XPedite1000 PPC440GX PrPMC board. See the README.ppc440 for additional
information.


SWITCH SETTINGS & JUMPERS
==========================

Jumpers selected for AMD29LV040B flash part as the boot flash.


I2C Strap EEPROM & Environment Settings
=======================================

The XPedite1000 uses a single I2C eeprom for the 440 strappings and for
the environment variables. The first page (256 bytes) contains the
strappings and the 2 EMAC HW Ethernet addresses. Be careful not to
change the 1st page of the EEPROM! Unpopulated jumper J560 can get you
out of trouble as it disables the strapping read from EEPROM.

I2C probe
=====================

The i2c utilities work and have been tested on Rev B. of the 440GX. See
README.ebony for more information about i2c probing with the 440.


GETTING OUT OF I2C TROUBLE
===========================

(Direct quote from README.ebony)
If you're like me ... you may have screwed up your bootstrap serial
eeprom ... or worse, your SPD eeprom when experimenting with the
i2c commands. If so, here are some ideas on how to get out of
trouble:

Serial bootstrap eeprom corruption:
-----------------------------------
Power down the board and set the following straps:

J560 - closed

This will select the default sys0 and sys1 settings (the serial
eeproms are not used). Then power up the board and fix the serial
eeprom using the 'i2c mm' command. Here are the values I currently
use:

=> i2c md 50 0 10

0000: 85 7d 42 06 07 80 11 00 00 00 00 00 00 00 00 00 .}B.............

Once you have the eeproms set correctly change the
J560 straps as you desire.


PPC440GX Ethernet EMACs
=======================

The XES XPedite1000 uses emac 2 & 3 and ignores emac 0 & 1. PHYs are connected
only to emac 2 & 3. The HW Ethernet addresses are read from the i2c eeprom and
placed in the bd info structure for enet2addr and enet3addr. The ethernet driver
senses that enetaddr and enet1addr are 0's and does not use them.

As of this writing gigabit ethernet and the TCPIP acceleration hardware is not
supported.


Flash Support
=============

As of this writing, there is support for the 1/2mb boot flash only. User flash
is not yet supported.


Regards,
--Travis
<travis.sawyer@sandburst.com>