upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/st/nmdk8815/platform.S

340 lines
6.8 KiB

/*
* Board specific setup info
*
* (C) Copyright 2005
* STMicrolelctronics, <www.st.com>
*
* (C) Copyright 2004, ARM Ltd.
* Philippe Robin, <philippe.robin@arm.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <config.h>
#include <version.h>
.globl lowlevel_init
lowlevel_init:
/* Jump to the flash address */
ldr r0, =CFG_ONENAND_BASE
/*
* Make it independent whether we boot from 0x0 or 0x30000000.
* Non-portable: it relies on the knowledge that ip has to be updated
*/
orr ip, ip, r0 /* adjust return address of cpu_init_crit */
orr lr, lr, r0 /* adjust return address */
orr pc, pc, r0 /* jump to the normal address */
nop
/* Initialize PLL, Remap clear, FSMC, MPMC here! */
/* What about GPIO, CLCD and UART */
/* PLL Initialization */
/* Prog the PLL1 @ 266 MHz ==> SDRAM Clock = 100.8 MHz */
ldr r0, =NOMADIK_SRC_BASE
ldr r1, =0x2B013502
str r1, [r0, #0x14]
/* Used to set all the timers clock to 2.4MHZ */
ldr r1, =0x2AAAA004
str r1, [r0]
ldr r1, =0x10000000
str r1, [r0, #0x10]
/* FSMC setup ---- */
ldr r0, =NOMADIK_FSMC_BASE
ldr r1, =0x10DB /* For 16-bit NOR flash */
str r1, [r0, #0x08]
ldr r1, =0x03333333 /* For 16-bit NOR flash */
str r1, [r0, #0xc]
/* oneNAND setting */
ldr r1, =0x0000105B /* BCR0 Prog control register */
str r1, [r0]
ldr r1, =0x0A200551 /* BTR0 Prog timing register */
str r1, [r0, #0x04]
/* preload the instructions into icache */
add r0, pc, #0x1F
bic r0, r0, #0x1F
mcr p15, 0, r0, c7, c13, 1
add r0, r0, #0x20
mcr p15, 0, r0, c7, c13, 1
/* Now Clear Remap */
ldr r0, =NOMADIK_SRC_BASE
ldr r1, =0x2004
str r1, [r0]
ldr r1, =0x10000000
str r1, [r0, #0x10]
ldr r0, =0x101E9000
ldr r1, =0x2004
str r1, [r0]
ldr r0, =NOMADIK_SRC_BASE
ldr r1, =0x2104
str r1, [r0]
/* FSMC setup -- */
mov r0, #(NOMADIK_FSMC_BASE & 0x10000000)
orr r0, r0, #(NOMADIK_FSMC_BASE & 0x0FFFFFFF)
ldr r1, =0x10DB /* For 16-bit NOR flash */
str r1, [r0, #0x8]
ldr r1, =0x03333333 /* For 16-bit NOR flash */
str r1, [r0, #0xc]
/* MPMC Setup */
ldr r0, =NOMADIK_MPMC_BASE
ldr r1, =0xF00003
str r1, [r0] /* Enable the MPMC and the DLL */
ldr r1, =0x183
str r1, [r0, #0x20]
ldr r2, =NOMADIK_PMU_BASE
ldr r1, =0x1111
str r1, [r2]
ldr r1, =0x1111 /* Prog the, mand delay strategy */
str r1, [r0, #0x28]
ldr r1, =0x103 /* NOP ,mand */
str r1, [r0, #0x20]
/* FIXME -- Wait required here */
ldr r1, =0x103 /* PALL ,mand*/
str r1, [r0, #0x20]
ldr r1, =0x1
str r1, [r0, #0x24] /* To do at least two auto-refresh */
/* FIXME -- Wait required here */
/* Auto-refresh period = 7.8us @ SDRAM Clock = 100.8 MHz */
ldr r1, =0x31
str r1, [r0, #0x24]
/* Prog Little Endian, Not defined in 8800 board */
ldr r1, =0x0
str r1, [r0, #0x8]
ldr r1, =0x2
str r1, [r0, #0x30] /* Prog tRP timing */
ldr r1, =0x4 /* Change for 8815 */
str r1, [r0, #0x34] /* Prog tRAS timing */
ldr r1, =0xB
str r1, [r0, #0x38] /* Prog tSREX timing */
ldr r1, =0x1
str r1, [r0, #0x44] /* Prog tWR timing */
ldr r1, =0x8
str r1, [r0, #0x48] /* Prog tRC timing */
ldr r1, =0xA
str r1, [r0, #0x4C] /* Prog tRFC timing */
ldr r1, =0xB
str r1, [r0, #0x50] /* Prog tXSR timing */
ldr r1, =0x1
str r1, [r0, #0x54] /* Prog tRRD timing */
ldr r1, =0x1
str r1, [r0, #0x58] /* Prog tMRD timing */
ldr r1, =0x1
str r1, [r0, #0x5C] /* Prog tCDLR timing */
/* DDR-SDRAM MEMORY IS ON BANK0 8815 */
ldr r1, =0x304 /* Prog RAS and CAS for CS 0 */
str r1, [r0, #0x104]
/* SDR-SDRAM MEMORY IS ON BANK1 8815 */
ldr r1, =0x304 /* Prog RAS and CAS for CS 1 */
str r1, [r0, #0x124]
/* THE DATA BUS WIDE IS PROGRAM FOR 16-BITS */
/* DDR-SDRAM MEMORY IS ON BANK0*/
ldr r1, =0x884 /* 8815 : config reg in BRC for CS0 */
str r1, [r0, #0x100]
/*SDR-SDRAM MEMORY IS ON BANK1*/
ldr r1, =0x884 /* 8815 : config reg in BRC for CS1 */
str r1, [r0, #0x120]
ldr r1, =0x83 /*MODE Mand*/
str r1, [r0, #0x20]
/* LOAD MODE REGISTER FOR 2 bursts of 16b, with DDR mem ON BANK0 */
ldr r1, =0x62000 /*Data in*/
ldr r1, [r1]
/* LOAD MODE REGISTER FOR 2 bursts of 16b, with DDR mem ON BANK1 */
ldr r1, =0x8062000
ldr r1, [r1]
ldr r1, =0x003
str r1, [r0, #0x20]
/* ENABLE ALL THE BUFFER FOR EACH AHB PORT*/
ldr r1, =0x01 /* Enable buffer 0 */
str r1, [r0, #0x400]
ldr r1, =0x01 /* Enable buffer 1 */
str r1, [r0, #0x420]
ldr r1, =0x01 /* Enable buffer 2 */
str r1, [r0, #0x440]
ldr r1, =0x01 /* Enable buffer 3 */
str r1, [r0, #0x460]
ldr r1, =0x01 /* Enable buffer 4 */
str r1, [r0, #0x480]
ldr r1, =0x01 /* Enable buffer 5 */
str r1, [r0, #0x4A0]
/* GPIO settings */
ldr r0, =NOMADIK_GPIO1_BASE
ldr r1, =0xC0600000
str r1, [r0, #0x20]
ldr r1, =0x3F9FFFFF /* ABHI change this for uart1 */
str r1, [r0, #0x24]
ldr r1, =0x3F9FFFFF /* ABHI change this for uart1 */
str r1, [r0, #0x28]
ldr r0, =NOMADIK_GPIO0_BASE
ldr r1, =0xFFFFFFFF
str r1, [r0, #0x20]
ldr r1, =0x00
str r1, [r0, #0x24]
ldr r1, =0x00
str r1, [r0, #0x28]
/* Configure CPLD_CTRL register for enabling MUX logic for UART0/UART2 */
ldr r0, =NOMADIK_FSMC_BASE
ldr r1, =0x10DB /* INIT FSMC bank 0 */
str r1, [r0, #0x00]
ldr r1, =0x0FFFFFFF
str r1, [r0, #0x04]
ldr r1, =0x010DB /* INIT FSMC bank 1 */
str r1, [r0, #0x08]
ldr r1, =0x00FFFFFFF
str r1, [r0, #0x0C]
ldr r0, =NOMADIK_UART0_BASE
ldr r1, =0x00000000
str r1, [r0, #0x30]
ldr r1, =0x0000004e
str r1, [r0, #0x24]
ldr r1, =0x00000008
str r1, [r0, #0x28]
ldr r1, =0x00000060
str r1, [r0, #0x2C]
ldr r1, =0x00000301
str r1, [r0, #0x30]
ldr r1, =0x00000066
str r1, [r0]
ldr r0, =NOMADIK_UART1_BASE
ldr r1, =0x00000000
str r1, [r0, #0x30]
ldr r1, =0x0000004e
str r1, [r0, #0x24]
ldr r1, =0x00000008
str r1, [r0, #0x28]
ldr r1, =0x00000060
str r1, [r0, #0x2C]
ldr r1, =0x00000301
str r1, [r0, #0x30]
ldr r1, =0x00000066
str r1, [r0]
ldr r0, =NOMADIK_UART2_BASE
ldr r1, =0x00000000
str r1, [r0, #0x30]
ldr r1, =0x0000004e
str r1, [r0, #0x24]
ldr r1, =0x00000008
str r1, [r0, #0x28]
ldr r1, =0x00000060
str r1, [r0, #0x2C]
ldr r1, =0x00000301
str r1, [r0, #0x30]
ldr r1, =0x00000066
str r1, [r0]
/* Configure CPLD to enable UART0 */
mov pc, lr