upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
631 lines
17 KiB
631 lines
17 KiB
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) Stefano Babic <sbabic@denx.de>
|
|
*
|
|
* Based on other i.MX6 boards
|
|
*/
|
|
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/iomux.h>
|
|
#include <asm/arch/mx6-pins.h>
|
|
#include <linux/errno.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/mach-imx/mxc_i2c.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/mach-imx/boot_mode.h>
|
|
#include <asm/mach-imx/video.h>
|
|
#include <mmc.h>
|
|
#include <fsl_esdhc.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
#include <asm/arch/mxc_hdmi.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <i2c.h>
|
|
#include <input.h>
|
|
#include <power/pmic.h>
|
|
#include <power/pfuze100_pmic.h>
|
|
#include <asm/arch/mx6-ddr.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define OPEN_PAD_CTRL (PAD_CTL_ODE | PAD_CTL_DSE_DISABLE | (0 << 12))
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
|
|
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
|
|
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
|
|
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
|
|
|
|
#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
|
|
|
|
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
|
|
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
|
|
|
|
#define I2C_PMIC 1
|
|
|
|
#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
|
|
|
|
#define ETH_PHY_RESET IMX_GPIO_NR(2, 4)
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = imx_ddr_size();
|
|
|
|
return 0;
|
|
}
|
|
|
|
iomux_v3_cfg_t const uart2_pads[] = {
|
|
MX6_PAD_SD3_DAT5__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
MX6_PAD_SD3_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
static void setup_iomux_uart(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
|
|
}
|
|
|
|
#ifdef CONFIG_TARGET_ZC5202
|
|
iomux_v3_cfg_t const enet_pads[] = {
|
|
MX6_PAD_GPIO_18__ENET_RX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_KEY_COL2__ENET_RX_DATA2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_KEY_COL0__ENET_RX_DATA3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
|
|
MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_GPIO_19__ENET_TX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_KEY_ROW2__ENET_TX_DATA2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_KEY_ROW0__ENET_TX_DATA3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_RX_ER__ENET_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
|
|
/* Switch Reset */
|
|
MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
|
|
/* Switch Interrupt */
|
|
MX6_PAD_NANDF_D5__GPIO2_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
/* use CRS and COL pads as GPIOs */
|
|
MX6_PAD_KEY_COL3__GPIO4_IO12 | MUX_PAD_CTRL(OPEN_PAD_CTRL),
|
|
MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(OPEN_PAD_CTRL),
|
|
|
|
};
|
|
|
|
#define BOARD_NAME "EL6x-ZC5202"
|
|
#else
|
|
iomux_v3_cfg_t const enet_pads[] = {
|
|
MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
|
|
MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
MX6_PAD_NANDF_D5__GPIO2_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
#define BOARD_NAME "EL6x-ZC5601"
|
|
#endif
|
|
|
|
static void setup_iomux_enet(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
|
|
|
|
#ifdef CONFIG_TARGET_ZC5202
|
|
/* set CRS and COL to input */
|
|
gpio_direction_input(IMX_GPIO_NR(4, 9));
|
|
gpio_direction_input(IMX_GPIO_NR(4, 12));
|
|
|
|
/* Reset Switch */
|
|
gpio_direction_output(ETH_PHY_RESET , 0);
|
|
mdelay(2);
|
|
gpio_set_value(ETH_PHY_RESET, 1);
|
|
#endif
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_MXC_SPI
|
|
#ifdef CONFIG_TARGET_ZC5202
|
|
iomux_v3_cfg_t const ecspi1_pads[] = {
|
|
MX6_PAD_DISP0_DAT20__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_DISP0_DAT21__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_DISP0_DAT22__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_DISP0_DAT23__GPIO5_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
MX6_PAD_DISP0_DAT15__GPIO5_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
iomux_v3_cfg_t const ecspi3_pads[] = {
|
|
MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_DISP0_DAT7__GPIO4_IO28 | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_DISP0_DAT8__GPIO4_IO29 | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_DISP0_DAT9__GPIO4_IO30 | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_DISP0_DAT10__GPIO4_IO31 | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
};
|
|
#endif
|
|
|
|
iomux_v3_cfg_t const ecspi4_pads[] = {
|
|
MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
|
|
MX6_PAD_EIM_D20__GPIO3_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
int board_spi_cs_gpio(unsigned bus, unsigned cs)
|
|
{
|
|
return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
|
|
? (IMX_GPIO_NR(3, 20)) : -1;
|
|
}
|
|
|
|
static void setup_spi(void)
|
|
{
|
|
#ifdef CONFIG_TARGET_ZC5202
|
|
gpio_request(IMX_GPIO_NR(5, 17), "spi_cs0");
|
|
gpio_request(IMX_GPIO_NR(5, 9), "spi_cs1");
|
|
gpio_direction_output(IMX_GPIO_NR(5, 17), 1);
|
|
gpio_direction_output(IMX_GPIO_NR(5, 9), 1);
|
|
imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
|
|
#endif
|
|
|
|
gpio_request(IMX_GPIO_NR(3, 20), "spi4_cs0");
|
|
gpio_direction_output(IMX_GPIO_NR(3, 20), 1);
|
|
imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
|
|
|
|
enable_spi_clk(true, 3);
|
|
}
|
|
#endif
|
|
|
|
static struct i2c_pads_info i2c_pad_info1 = {
|
|
.scl = {
|
|
.i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | I2C_PAD,
|
|
.gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | I2C_PAD,
|
|
.gp = IMX_GPIO_NR(2, 30)
|
|
},
|
|
.sda = {
|
|
.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
|
|
.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
|
|
.gp = IMX_GPIO_NR(4, 13)
|
|
}
|
|
};
|
|
|
|
static struct i2c_pads_info i2c_pad_info2 = {
|
|
.scl = {
|
|
.i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | I2C_PAD,
|
|
.gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | I2C_PAD,
|
|
.gp = IMX_GPIO_NR(1, 5)
|
|
},
|
|
.sda = {
|
|
.i2c_mode = MX6_PAD_GPIO_16__I2C3_SDA | I2C_PAD,
|
|
.gpio_mode = MX6_PAD_GPIO_16__GPIO7_IO11 | I2C_PAD,
|
|
.gp = IMX_GPIO_NR(7, 11)
|
|
}
|
|
};
|
|
|
|
iomux_v3_cfg_t const usdhc2_pads[] = {
|
|
MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_GPIO_4__SD2_CD_B | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
|
|
};
|
|
|
|
iomux_v3_cfg_t const usdhc4_pads[] = {
|
|
MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
};
|
|
|
|
#ifdef CONFIG_FSL_ESDHC
|
|
struct fsl_esdhc_cfg usdhc_cfg[2] = {
|
|
{USDHC2_BASE_ADDR},
|
|
{USDHC4_BASE_ADDR},
|
|
};
|
|
|
|
#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
|
|
|
|
int board_mmc_getcd(struct mmc *mmc)
|
|
{
|
|
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
|
|
int ret = 0;
|
|
|
|
switch (cfg->esdhc_base) {
|
|
case USDHC2_BASE_ADDR:
|
|
ret = !gpio_get_value(USDHC2_CD_GPIO);
|
|
break;
|
|
case USDHC4_BASE_ADDR:
|
|
ret = 1; /* eMMC/uSDHC4 is always present */
|
|
break;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
int board_mmc_init(bd_t *bis)
|
|
{
|
|
#ifndef CONFIG_SPL_BUILD
|
|
int ret;
|
|
int i;
|
|
|
|
/*
|
|
* According to the board_mmc_init() the following map is done:
|
|
* (U-boot device node) (Physical Port)
|
|
* mmc0 SD2
|
|
* mmc1 SD3
|
|
* mmc2 eMMC
|
|
*/
|
|
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
|
|
switch (i) {
|
|
case 0:
|
|
imx_iomux_v3_setup_multiple_pads(
|
|
usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
|
|
gpio_direction_input(USDHC2_CD_GPIO);
|
|
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
|
|
break;
|
|
case 1:
|
|
imx_iomux_v3_setup_multiple_pads(
|
|
usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
|
|
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
|
|
break;
|
|
default:
|
|
printf("Warning: you configured more USDHC controllers"
|
|
"(%d) then supported by the board (%d)\n",
|
|
i + 1, CONFIG_SYS_FSL_USDHC_NUM);
|
|
return -EINVAL;
|
|
}
|
|
|
|
ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
#else
|
|
struct src *psrc = (struct src *)SRC_BASE_ADDR;
|
|
unsigned reg = readl(&psrc->sbmr1) >> 11;
|
|
|
|
/*
|
|
* Upon reading BOOT_CFG register the following map is done:
|
|
* Bit 11 and 12 of BOOT_CFG register can determine the current
|
|
* mmc port
|
|
* 0x1 SD1
|
|
* 0x2 SD2
|
|
* 0x3 SD4
|
|
*/
|
|
|
|
switch (reg & 0x3) {
|
|
case 0x1:
|
|
imx_iomux_v3_setup_multiple_pads(
|
|
usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
|
|
usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
|
|
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
|
|
gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
|
|
break;
|
|
case 0x3:
|
|
imx_iomux_v3_setup_multiple_pads(
|
|
usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
|
|
usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
|
|
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
|
|
gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
|
|
break;
|
|
}
|
|
|
|
return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
|
|
#endif
|
|
|
|
}
|
|
#endif
|
|
|
|
|
|
/*
|
|
* Do not overwrite the console
|
|
* Use always serial for U-Boot console
|
|
*/
|
|
int overwrite_console(void)
|
|
{
|
|
return 1;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
setup_iomux_enet();
|
|
enable_enet_clk(1);
|
|
|
|
return cpu_eth_init(bis);
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
|
|
setup_iomux_uart();
|
|
setup_spi();
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
|
|
|
|
setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
|
|
setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int power_init_board(void)
|
|
{
|
|
struct pmic *p;
|
|
int ret;
|
|
unsigned int reg;
|
|
|
|
ret = power_pfuze100_init(I2C_PMIC);
|
|
if (ret)
|
|
return ret;
|
|
|
|
p = pmic_get("PFUZE100");
|
|
ret = pmic_probe(p);
|
|
if (ret)
|
|
return ret;
|
|
|
|
pmic_reg_read(p, PFUZE100_DEVICEID, ®);
|
|
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
|
|
|
|
/* Increase VGEN3 from 2.5 to 2.8V */
|
|
pmic_reg_read(p, PFUZE100_VGEN3VOL, ®);
|
|
reg &= ~LDO_VOL_MASK;
|
|
reg |= LDOB_2_80V;
|
|
pmic_reg_write(p, PFUZE100_VGEN3VOL, reg);
|
|
|
|
/* Increase VGEN5 from 2.8 to 3V */
|
|
pmic_reg_read(p, PFUZE100_VGEN5VOL, ®);
|
|
reg &= ~LDO_VOL_MASK;
|
|
reg |= LDOB_3_00V;
|
|
pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
|
|
|
|
/* Set SW1AB stanby volage to 0.975V */
|
|
pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®);
|
|
reg &= ~SW1x_STBY_MASK;
|
|
reg |= SW1x_0_975V;
|
|
pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
|
|
|
|
/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
|
|
pmic_reg_read(p, PFUZE100_SW1ABCONF, ®);
|
|
reg &= ~SW1xCONF_DVSSPEED_MASK;
|
|
reg |= SW1xCONF_DVSSPEED_4US;
|
|
pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
|
|
|
|
/* Set SW1C standby voltage to 0.975V */
|
|
pmic_reg_read(p, PFUZE100_SW1CSTBY, ®);
|
|
reg &= ~SW1x_STBY_MASK;
|
|
reg |= SW1x_0_975V;
|
|
pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
|
|
|
|
/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
|
|
pmic_reg_read(p, PFUZE100_SW1CCONF, ®);
|
|
reg &= ~SW1xCONF_DVSSPEED_MASK;
|
|
reg |= SW1xCONF_DVSSPEED_4US;
|
|
pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_CMD_BMODE
|
|
static const struct boot_mode board_boot_modes[] = {
|
|
/* 4 bit bus width */
|
|
{"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
|
|
/* 8 bit bus width */
|
|
{"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
|
|
{NULL, 0},
|
|
};
|
|
#endif
|
|
|
|
int board_late_init(void)
|
|
{
|
|
#ifdef CONFIG_CMD_BMODE
|
|
add_board_boot_modes(board_boot_modes);
|
|
#endif
|
|
|
|
env_set("board_name", BOARD_NAME);
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
puts("Board: ");
|
|
puts(BOARD_NAME "\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
#include <spl.h>
|
|
#include <linux/libfdt.h>
|
|
|
|
const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
|
|
.dram_sdclk_0 = 0x00020030,
|
|
.dram_sdclk_1 = 0x00020030,
|
|
.dram_cas = 0x00020030,
|
|
.dram_ras = 0x00020030,
|
|
.dram_reset = 0x00020030,
|
|
.dram_sdcke0 = 0x00003000,
|
|
.dram_sdcke1 = 0x00003000,
|
|
.dram_sdba2 = 0x00000000,
|
|
.dram_sdodt0 = 0x00003030,
|
|
.dram_sdodt1 = 0x00003030,
|
|
.dram_sdqs0 = 0x00000030,
|
|
.dram_sdqs1 = 0x00000030,
|
|
.dram_sdqs2 = 0x00000030,
|
|
.dram_sdqs3 = 0x00000030,
|
|
.dram_sdqs4 = 0x00000030,
|
|
.dram_sdqs5 = 0x00000030,
|
|
.dram_sdqs6 = 0x00000030,
|
|
.dram_sdqs7 = 0x00000030,
|
|
.dram_dqm0 = 0x00020030,
|
|
.dram_dqm1 = 0x00020030,
|
|
.dram_dqm2 = 0x00020030,
|
|
.dram_dqm3 = 0x00020030,
|
|
.dram_dqm4 = 0x00020030,
|
|
.dram_dqm5 = 0x00020030,
|
|
.dram_dqm6 = 0x00020030,
|
|
.dram_dqm7 = 0x00020030,
|
|
};
|
|
|
|
const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
|
|
.grp_ddr_type = 0x000C0000,
|
|
.grp_ddrmode_ctl = 0x00020000,
|
|
.grp_ddrpke = 0x00000000,
|
|
.grp_addds = 0x00000030,
|
|
.grp_ctlds = 0x00000030,
|
|
.grp_ddrmode = 0x00020000,
|
|
.grp_b0ds = 0x00000030,
|
|
.grp_b1ds = 0x00000030,
|
|
.grp_b2ds = 0x00000030,
|
|
.grp_b3ds = 0x00000030,
|
|
.grp_b4ds = 0x00000030,
|
|
.grp_b5ds = 0x00000030,
|
|
.grp_b6ds = 0x00000030,
|
|
.grp_b7ds = 0x00000030,
|
|
};
|
|
|
|
const struct mx6_mmdc_calibration mx6_mmcd_calib = {
|
|
.p0_mpwldectrl0 = 0x001F001F,
|
|
.p0_mpwldectrl1 = 0x001F001F,
|
|
.p1_mpwldectrl0 = 0x00440044,
|
|
.p1_mpwldectrl1 = 0x00440044,
|
|
.p0_mpdgctrl0 = 0x434B0350,
|
|
.p0_mpdgctrl1 = 0x034C0359,
|
|
.p1_mpdgctrl0 = 0x434B0350,
|
|
.p1_mpdgctrl1 = 0x03650348,
|
|
.p0_mprddlctl = 0x4436383B,
|
|
.p1_mprddlctl = 0x39393341,
|
|
.p0_mpwrdlctl = 0x35373933,
|
|
.p1_mpwrdlctl = 0x48254A36,
|
|
};
|
|
|
|
/* MT41K128M16JT-125 */
|
|
static struct mx6_ddr3_cfg mem_ddr = {
|
|
.mem_speed = 1600,
|
|
.density = 2,
|
|
.width = 16,
|
|
.banks = 8,
|
|
.rowaddr = 14,
|
|
.coladdr = 10,
|
|
.pagesz = 2,
|
|
.trcd = 1375,
|
|
.trcmin = 4875,
|
|
.trasmin = 3500,
|
|
};
|
|
|
|
static void ccgr_init(void)
|
|
{
|
|
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
|
|
|
|
writel(0x00C03F3F, &ccm->CCGR0);
|
|
writel(0x0030FC03, &ccm->CCGR1);
|
|
writel(0x0FFFC000, &ccm->CCGR2);
|
|
writel(0x3FF00000, &ccm->CCGR3);
|
|
writel(0x00FFF300, &ccm->CCGR4);
|
|
writel(0x0F0000C3, &ccm->CCGR5);
|
|
writel(0x000003FF, &ccm->CCGR6);
|
|
}
|
|
|
|
/*
|
|
* This section requires the differentiation between iMX6 Sabre boards, but
|
|
* for now, it will configure only for the mx6q variant.
|
|
*/
|
|
static void spl_dram_init(void)
|
|
{
|
|
struct mx6_ddr_sysinfo sysinfo = {
|
|
/* width of data bus:0=16,1=32,2=64 */
|
|
.dsize = 2,
|
|
/* config for full 4GB range so that get_mem_size() works */
|
|
.cs_density = 32, /* 32Gb per CS */
|
|
/* single chip select */
|
|
.ncs = 1,
|
|
.cs1_mirror = 0,
|
|
.rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
|
|
.rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
|
|
.walat = 1, /* Write additional latency */
|
|
.ralat = 5, /* Read additional latency */
|
|
.mif3_mode = 3, /* Command prediction working mode */
|
|
.bi_on = 1, /* Bank interleaving enabled */
|
|
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
|
|
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
|
|
.ddr_type = DDR_TYPE_DDR3,
|
|
.refsel = 1, /* Refresh cycles at 32KHz */
|
|
.refr = 7, /* 8 refresh commands per refresh cycle */
|
|
};
|
|
|
|
mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs);
|
|
mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
|
|
}
|
|
|
|
void board_init_f(ulong dummy)
|
|
{
|
|
/* setup AIPS and disable watchdog */
|
|
arch_cpu_init();
|
|
|
|
ccgr_init();
|
|
gpr_init();
|
|
|
|
/* iomux and setup of i2c */
|
|
board_early_init_f();
|
|
|
|
/* setup GP timer */
|
|
timer_init();
|
|
|
|
/* UART clocks enabled and gd valid - init serial console */
|
|
preloader_console_init();
|
|
|
|
/* DDR initialization */
|
|
spl_dram_init();
|
|
|
|
/* Clear the BSS. */
|
|
memset(__bss_start, 0, __bss_end - __bss_start);
|
|
|
|
/* load/boot image from boot device */
|
|
board_init_r(NULL, 0);
|
|
}
|
|
|
|
#endif
|
|
|