upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/arch/arm/cpu/armv8/Kconfig

160 lines
5.9 KiB

if ARM64
config ARMV8_SPL_EXCEPTION_VECTORS
bool "Install crash dump exception vectors"
depends on SPL
default y
help
The default exception vector table is only used for the crash
dump, but still takes quite a lot of space in the image size.
Say N here if you are running out of code space in the image
and want to save some space at the cost of less debugging info.
config ARMV8_MULTIENTRY
bool "Enable multiple CPUs to enter into U-Boot"
config ARMV8_SET_SMPEN
bool "Enable data coherency with other cores in cluster"
help
Say Y here if there is not any trust firmware to set
CPUECTLR_EL1.SMPEN bit before U-Boot.
For A53, it enables data coherency with other cores in the
cluster, and for A57/A72, it enables receiving of instruction
cache and TLB maintenance operations.
Cortex A53/57/72 cores require CPUECTLR_EL1.SMPEN set even
for single core systems. Unfortunately write access to this
register may be controlled by EL3/EL2 firmware. To be more
precise, by default (if there is EL2/EL3 firmware running)
this register is RO for NS EL1.
This switch can be used to avoid writing to CPUECTLR_EL1,
it can be safely enabled when EL2/EL3 initialized SMPEN bit
or when CPU implementation doesn't include that register.
config ARMV8_SPIN_TABLE
bool "Support spin-table enable method"
depends on ARMV8_MULTIENTRY && OF_LIBFDT
help
Say Y here to support "spin-table" enable method for booting Linux.
To use this feature, you must do:
- Specify enable-method = "spin-table" in each CPU node in the
Device Tree you are using to boot the kernel
- Bring secondary CPUs into U-Boot proper in a board specific
manner. This must be done *after* relocation. Otherwise, the
secondary CPUs will spin in unprotected memory area because the
master CPU protects the relocated spin code.
U-Boot automatically does:
- Set "cpu-release-addr" property of each CPU node
(overwrites it if already exists).
- Reserve the code for the spin-table and the release address
via a /memreserve/ region in the Device Tree.
menu "ARMv8 secure monitor firmware"
config ARMV8_SEC_FIRMWARE_SUPPORT
bool "Enable ARMv8 secure monitor firmware framework support"
select FIT
select OF_LIBFDT
help
This framework is aimed at making secure monitor firmware load
process brief.
Note: Only FIT format image is supported.
You should prepare and provide the below information:
- Address of secure firmware.
- Address to hold the return address from secure firmware.
- Secure firmware FIT image related information.
Such as: SEC_FIRMWARE_FIT_IMAGE and SEC_FIRMEWARE_FIT_CNF_NAME
- The target exception level that secure monitor firmware will
return to.
config SPL_ARMV8_SEC_FIRMWARE_SUPPORT
bool "Enable ARMv8 secure monitor firmware framework support for SPL"
select SPL_FIT
select SPL_OF_LIBFDT
help
Say Y here to support this framework in SPL phase.
config SEC_FIRMWARE_ARMV8_PSCI
bool "PSCI implementation in secure monitor firmware"
depends on ARMV8_SEC_FIRMWARE_SUPPORT || SPL_ARMV8_SEC_FIRMWARE_SUPPORT
help
This config enables the ARMv8 PSCI implementation in secure monitor
firmware. This is a private PSCI implementation and different from
those implemented under the common ARMv8 PSCI framework.
config ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT
bool "ARMv8 secure monitor firmware ERET address byteorder swap"
depends on ARMV8_SEC_FIRMWARE_SUPPORT || SPL_ARMV8_SEC_FIRMWARE_SUPPORT
help
Say Y here when the endianness of the register or memory holding the
Secure firmware exception return address is different with core's.
endmenu
config PSCI_RESET
bool "Use PSCI for reset and shutdown"
default y
depends on !ARCH_EXYNOS7 && !ARCH_BCM283X && \
!TARGET_LS2080A_SIMU && !TARGET_LS2080AQDS && \
!TARGET_LS2080ARDB && !TARGET_LS2080A_EMU && \
!TARGET_LS1088ARDB && !TARGET_LS1088AQDS && \
!TARGET_LS1012ARDB && !TARGET_LS1012AFRDM && \
!TARGET_LS1012A2G5RDB && !TARGET_LS1012AQDS && \
!TARGET_LS1012AFRWY && \
!TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \
!TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \
!TARGET_LS2081ARDB && \
!ARCH_UNIPHIER && !TARGET_S32V234EVB
help
Most armv8 systems have PSCI support enabled in EL3, either through
ARM Trusted Firmware or other firmware.
On these systems, we do not need to implement system reset manually,
but can instead rely on higher level firmware to deal with it.
Select Y here to make use of PSCI calls for system reset
config ARMV8_PSCI
bool "Enable PSCI support" if EXPERT
default n
help
PSCI is Power State Coordination Interface defined by ARM.
The PSCI in U-boot provides a general framework and each platform
can implement their own specific PSCI functions.
Say Y here to enable PSCI support on ARMv8 platform.
config ARMV8_PSCI_NR_CPUS
int "Maximum supported CPUs for PSCI"
depends on ARMV8_PSCI
default 4
help
The maximum number of CPUs supported in the PSCI firmware.
It is no problem to set a larger value than the number of CPUs in
the actual hardware implementation.
config ARMV8_PSCI_CPUS_PER_CLUSTER
int "Number of CPUs per cluster"
depends on ARMV8_PSCI
default 0
help
The number of CPUs per cluster, suppose each cluster has same number
of CPU cores, platforms with asymmetric clusters don't apply here.
A value 0 or no definition of it works for single cluster system.
System with multi-cluster should difine their own exact value.
if SYS_HAS_ARMV8_SECURE_BASE
config ARMV8_SECURE_BASE
hex "Secure address for PSCI image"
depends on ARMV8_PSCI
help
Address for placing the PSCI text, data and stack sections.
If not defined, the PSCI sections are placed together with the u-boot
but platform can choose to place PSCI code image separately in other
places such as some secure RAM built-in SOC etc.
endif
endif