upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/drivers/net/Kconfig

439 lines
12 KiB

source "drivers/net/phy/Kconfig"
source "drivers/net/pfe_eth/Kconfig"
config DM_ETH
bool "Enable Driver Model for Ethernet drivers"
depends on DM
help
Enable driver model for Ethernet.
The eth_*() interface will be implemented by the UC_ETH class
This is currently implemented in net/eth.c
Look in include/net.h for details.
config DRIVER_TI_CPSW
bool "TI Common Platform Ethernet Switch"
select PHYLIB
help
This driver supports the TI three port switch gigabit ethernet
subsystem found in the TI SoCs.
menuconfig NETDEVICES
bool "Network device support"
depends on NET
default y if DM_ETH
help
You must select Y to enable any network device support
Generally if you have any networking support this is a given
If unsure, say Y
if NETDEVICES
config PHY_GIGE
bool "Enable GbE PHY status parsing and configuration"
help
Enables support for parsing the status output and for
configuring GbE PHYs (affects the inner workings of some
commands and miiphyutil.c).
config AG7XXX
bool "Atheros AG7xxx Ethernet MAC support"
depends on DM_ETH && ARCH_ATH79
select PHYLIB
help
This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
config ALTERA_TSE
bool "Altera Triple-Speed Ethernet MAC support"
depends on DM_ETH
select PHYLIB
help
This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
Please find details on the "Triple-Speed Ethernet MegaCore Function
Resource Center" of Altera.
config BCM_SF2_ETH
bool "Broadcom SF2 (Starfighter2) Ethernet support"
select PHYLIB
help
This is an abstract framework which provides a generic interface
to MAC and DMA management for multiple Broadcom SoCs such as
Cygnus, NSP and bcm28155_ap platforms.
config BCM_SF2_ETH_DEFAULT_PORT
int "Broadcom SF2 (Starfighter2) Ethernet default port number"
depends on BCM_SF2_ETH
default 0
help
Default port number for the Starfighter2 ethernet driver.
config BCM_SF2_ETH_GMAC
bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
depends on BCM_SF2_ETH
help
This flag enables the ethernet support for Broadcom platforms with
GMAC such as Cygnus. This driver is based on the framework provided
by the BCM_SF2_ETH driver.
Say Y to any bcmcygnus based platforms.
config DWC_ETH_QOS
bool "Synopsys DWC Ethernet QOS device support"
depends on DM_ETH
select PHYLIB
help
This driver supports the Synopsys Designware Ethernet QOS (Quality
Of Service) IP block. The IP supports many options for bus type,
clocking/reset structure, and feature list. This driver currently
supports the specific configuration used in NVIDIA's Tegra186 chip,
but should be extensible to other combinations quite easily.
config E1000
bool "Intel PRO/1000 Gigabit Ethernet support"
help
This driver supports Intel(R) PRO/1000 gigabit ethernet family of
adapters. For more information on how to identify your adapter, go
to the Adapter & Driver ID Guide at:
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
config E1000_SPI_GENERIC
bool "Allow access to the Intel 8257x SPI bus"
depends on E1000
help
Allow generic access to the SPI bus on the Intel 8257x, for
example with the "sspi" command.
config E1000_SPI
bool "Enable SPI bus utility code"
depends on E1000
help
Utility code for direct access to the SPI bus on Intel 8257x.
This does not do anything useful unless you set at least one
of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
config CMD_E1000
bool "Enable the e1000 command"
depends on E1000
help
This enables the 'e1000' management command for E1000 devices. When
used on devices with SPI support you can reprogram the EEPROM from
U-Boot.
config ETH_SANDBOX
depends on DM_ETH && SANDBOX
default y
bool "Sandbox: Mocked Ethernet driver"
help
This driver simply responds with fake ARP replies and ping
replies that are used to verify network stack functionality
This driver is particularly useful in the test/dm/eth.c tests
config ETH_SANDBOX_RAW
depends on DM_ETH && SANDBOX
default y
bool "Sandbox: Bridge to Linux Raw Sockets"
help
This driver is a bridge from the bottom of the network stack
in U-Boot to the RAW AF_PACKET API in Linux. This allows real
network traffic to be tested from within sandbox. See
board/sandbox/README.sandbox for more details.
config ETH_DESIGNWARE
bool "Synopsys Designware Ethernet MAC"
select PHYLIB
help
This MAC is present in SoCs from various vendors. It supports
100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
provide the PHY (physical media interface).
config ETHOC
bool "OpenCores 10/100 Mbps Ethernet MAC"
help
This MAC is present in OpenRISC and Xtensa XTFPGA boards.
config FEC_MXC_SHARE_MDIO
bool "Share the MDIO bus for FEC controller"
depends on FEC_MXC
config FEC_MXC_MDIO_BASE
hex "MDIO base address for the FEC controller"
depends on FEC_MXC_SHARE_MDIO
help
This specifies the MDIO registers base address. It is used when
two FEC controllers share MDIO bus.
config FEC_MXC
bool "FEC Ethernet controller"
depends on MX5 || MX6 || MX7
help
This driver supports the 10/100 Fast Ethernet controller for
NXP i.MX processors.
config FTMAC100
bool "Ftmac100 Ethernet Support"
help
This MAC is present in Andestech SoCs.
config MVNETA
bool "Marvell Armada XP/385/3700 network interface support"
depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
select PHYLIB
help
This driver supports the network interface units in the
Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
config MVPP2
bool "Marvell Armada 375/7K/8K network interface support"
depends on ARMADA_375 || ARMADA_8K
select PHYLIB
help
This driver supports the network interface units in the
Marvell ARMADA 375, 7K and 8K SoCs.
config MACB
bool "Cadence MACB/GEM Ethernet Interface"
depends on DM_ETH
select PHYLIB
help
The Cadence MACB ethernet interface is found on many Atmel
AT91 and SAMA5 parts. This driver also supports the Cadence
GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
Say Y to include support for the MACB/GEM chip.
config MACB_ZYNQ
bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
depends on MACB
help
The Cadence MACB ethernet interface was used on Zynq platform.
Say Y to enable support for the MACB/GEM in Zynq chip.
config PCH_GBE
bool "Intel Platform Controller Hub EG20T GMAC driver"
depends on DM_ETH && DM_PCI
select PHYLIB
help
This MAC is present in Intel Platform Controller Hub EG20T. It
supports 10/100/1000 Mbps operation.
config RGMII
bool "Enable RGMII"
help
Enable the support of the Reduced Gigabit Media-Independent
Interface (RGMII).
config RTL8139
bool "Realtek 8139 series Ethernet controller driver"
help
This driver supports Realtek 8139 series fast ethernet family of
PCI chipsets/adapters.
config RTL8169
bool "Realtek 8169 series Ethernet controller driver"
help
This driver supports Realtek 8169 series gigabit ethernet family of
PCI/PCIe chipsets/adapters.
config SMC911X
bool "SMSC LAN911x and LAN921x controller driver"
if SMC911X
config SMC911X_BASE
hex "SMC911X Base Address"
help
Define this to hold the physical address
of the device (I/O space)
choice
prompt "SMC911X bus width"
default SMC911X_16_BIT
config SMC911X_32_BIT
bool "Enable 32-bit interface"
config SMC911X_16_BIT
bool "Enable 16-bit interface"
help
Define this if data bus is 16 bits. If your processor
automatically converts one 32 bit word to two 16 bit
words you may also try CONFIG_SMC911X_32_BIT.
endchoice
endif #SMC911X
config SUN7I_GMAC
bool "Enable Allwinner GMAC Ethernet support"
help
Enable the support for Sun7i GMAC Ethernet controller
config SUN7I_GMAC_FORCE_TXERR
bool "Force PA17 as gmac function"
depends on SUN7I_GMAC
help
Some ethernet phys needs TXERR control. Since the GMAC
doesn't have such signal, setting PA17 as GMAC function
makes the pin output low, which enables data transmission.
config SUN4I_EMAC
bool "Allwinner Sun4i Ethernet MAC support"
depends on DM_ETH
select PHYLIB
help
This driver supports the Allwinner based SUN4I Ethernet MAC.
config SUN8I_EMAC
bool "Allwinner Sun8i Ethernet MAC support"
depends on DM_ETH
select PHYLIB
select PHY_GIGE
help
This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
It can be found in H3/A64/A83T based SoCs and compatible with both
External and Internal PHYs.
config SH_ETHER
bool "Renesas SH Ethernet MAC"
select PHYLIB
help
This driver supports the Ethernet for Renesas SH and ARM SoCs.
config XILINX_AXIEMAC
depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
select PHYLIB
select MII
bool "Xilinx AXI Ethernet"
help
This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
config XILINX_EMACLITE
depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
select PHYLIB
select MII
bool "Xilinx Ethernetlite"
help
This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
config ZYNQ_GEM
depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
select PHYLIB
bool "Xilinx Ethernet GEM"
help
This MAC is present in Xilinx Zynq and ZynqMP SoCs.
config PIC32_ETH
bool "Microchip PIC32 Ethernet Support"
depends on DM_ETH && MACH_PIC32
select PHYLIB
help
This driver implements 10/100 Mbps Ethernet and MAC layer for
Microchip PIC32 microcontrollers.
config GMAC_ROCKCHIP
bool "Rockchip Synopsys Designware Ethernet MAC"
depends on DM_ETH && ETH_DESIGNWARE
help
This driver provides Rockchip SoCs network support based on the
Synopsys Designware driver.
config RENESAS_RAVB
bool "Renesas Ethernet AVB MAC"
depends on DM_ETH && RCAR_GEN3
select PHYLIB
help
This driver implements support for the Ethernet AVB block in
Renesas M3 and H3 SoCs.
config MPC8XX_FEC
bool "Fast Ethernet Controller on MPC8XX"
depends on MPC8xx
select MII
help
This driver implements support for the Fast Ethernet Controller
on MPC8XX
config ETHER_ON_FEC1
bool "FEC1"
depends on MPC8XX_FEC
default y
config FEC1_PHY
int "FEC1 PHY"
depends on ETHER_ON_FEC1
default -1
help
Define to the hardcoded PHY address which corresponds
to the given FEC; i. e.
#define CONFIG_FEC1_PHY 4
means that the PHY with address 4 is connected to FEC1
When set to -1, means to probe for first available.
config PHY_NORXERR
bool "PHY_NORXERR"
depends on ETHER_ON_FEC1
default n
help
The PHY does not have a RXERR line (RMII only).
(so program the FEC to ignore it).
config ETHER_ON_FEC2
bool "FEC2"
depends on MPC8XX_FEC && MPC885
default y
config FEC2_PHY
int "FEC2 PHY"
depends on ETHER_ON_FEC2
default -1
help
Define to the hardcoded PHY address which corresponds
to the given FEC; i. e.
#define CONFIG_FEC1_PHY 4
means that the PHY with address 4 is connected to FEC1
When set to -1, means to probe for first available.
config FEC2_PHY_NORXERR
bool "PHY_NORXERR"
depends on ETHER_ON_FEC2
default n
help
The PHY does not have a RXERR line (RMII only).
(so program the FEC to ignore it).
config SYS_DPAA_QBMAN
bool "Device tree fixup for QBMan on freescale SOCs"
depends on (ARM || PPC) && !SPL_BUILD
default y if ARCH_B4860 || \
ARCH_B4420 || \
ARCH_P1023 || \
ARCH_P2041 || \
ARCH_T1023 || \
ARCH_T1024 || \
ARCH_T1040 || \
ARCH_T1042 || \
ARCH_T2080 || \
ARCH_T2081 || \
ARCH_T4240 || \
ARCH_T4160 || \
ARCH_P4080 || \
ARCH_P3041 || \
ARCH_P5040 || \
ARCH_P5020 || \
ARCH_LS1043A || \
ARCH_LS1046A
help
QBman fixups to allow deep sleep in DPAA 1 SOCs
config TSEC_ENET
select PHYLIB
bool "Enable Three-Speed Ethernet Controller"
help
This driver implements support for the (Enhanced) Three-Speed
Ethernet Controller found on Freescale SoCs.
endif # NETDEVICES