upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/freescale/mx53evk/mx53evk.c

269 lines
6.7 KiB

/*
* (C) Copyright 2010 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/clock.h>
#include <asm/arch/iomux-mx53.h>
#include <linux/errno.h>
#include <asm/imx-common/boot_mode.h>
#include <netdev.h>
#include <i2c.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <power/pmic.h>
#include <fsl_pmic.h>
#include <asm/gpio.h>
#include <mc13892.h>
DECLARE_GLOBAL_DATA_PTR;
int dram_init(void)
{
/* dram_init must store complete ramsize in gd->ram_size */
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
PHYS_SDRAM_1_SIZE);
return 0;
}
#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
static void setup_iomux_uart(void)
{
static const iomux_v3_cfg_t uart_pads[] = {
NEW_PAD_CTRL(MX53_PAD_CSI0_DAT11__UART1_RXD_MUX, UART_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_CSI0_DAT10__UART1_TXD_MUX, UART_PAD_CTRL),
};
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
}
#define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
PAD_CTL_HYS | PAD_CTL_ODE)
static void setup_i2c(unsigned int port_number)
{
static const iomux_v3_cfg_t i2c1_pads[] = {
NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__I2C1_SDA, I2C_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__I2C1_SCL, I2C_PAD_CTRL),
};
static const iomux_v3_cfg_t i2c2_pads[] = {
NEW_PAD_CTRL(MX53_PAD_KEY_ROW3__I2C2_SDA, I2C_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_KEY_COL3__I2C2_SCL, I2C_PAD_CTRL),
};
switch (port_number) {
case 0:
imx_iomux_v3_setup_multiple_pads(i2c1_pads,
ARRAY_SIZE(i2c1_pads));
break;
case 1:
imx_iomux_v3_setup_multiple_pads(i2c2_pads,
ARRAY_SIZE(i2c2_pads));
break;
default:
printf("Warning: Wrong I2C port number\n");
break;
}
}
void power_init(void)
{
unsigned int val;
struct pmic *p;
int ret;
ret = pmic_init(I2C_0);
if (ret)
return;
p = pmic_get("FSL_PMIC");
if (!p)
return;
/* Set VDDA to 1.25V */
pmic_reg_read(p, REG_SW_2, &val);
val &= ~SWX_OUT_MASK;
val |= SWX_OUT_1_25;
pmic_reg_write(p, REG_SW_2, val);
/*
* Need increase VCC and VDDA to 1.3V
* according to MX53 IC TO2 datasheet.
*/
if (is_soc_rev(CHIP_REV_2_0) == 0) {
/* Set VCC to 1.3V for TO2 */
pmic_reg_read(p, REG_SW_1, &val);
val &= ~SWX_OUT_MASK;
val |= SWX_OUT_1_30;
pmic_reg_write(p, REG_SW_1, val);
/* Set VDDA to 1.3V for TO2 */
pmic_reg_read(p, REG_SW_2, &val);
val &= ~SWX_OUT_MASK;
val |= SWX_OUT_1_30;
pmic_reg_write(p, REG_SW_2, val);
}
}
static void setup_iomux_fec(void)
{
static const iomux_v3_cfg_t fec_pads[] = {
NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE),
NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
PAD_CTL_HYS | PAD_CTL_PKE),
NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
PAD_CTL_HYS | PAD_CTL_PKE),
};
imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
}
#ifdef CONFIG_FSL_ESDHC
struct fsl_esdhc_cfg esdhc_cfg[2] = {
{MMC_SDHC1_BASE_ADDR},
{MMC_SDHC3_BASE_ADDR},
};
int board_mmc_getcd(struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
int ret;
imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA11__GPIO3_11);
gpio_direction_input(IMX_GPIO_NR(3, 11));
imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA13__GPIO3_13);
gpio_direction_input(IMX_GPIO_NR(3, 13));
if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
ret = !gpio_get_value(IMX_GPIO_NR(3, 13));
else
ret = !gpio_get_value(IMX_GPIO_NR(3, 11));
return ret;
}
#define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
PAD_CTL_PUS_100K_UP)
#define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
PAD_CTL_DSE_HIGH)
int board_mmc_init(bd_t *bis)
{
static const iomux_v3_cfg_t sd1_pads[] = {
NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
MX53_PAD_EIM_DA13__GPIO3_13,
};
static const iomux_v3_cfg_t sd2_pads[] = {
NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
SD_CMD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL),
MX53_PAD_EIM_DA11__GPIO3_11,
};
u32 index;
int ret;
esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
switch (index) {
case 0:
imx_iomux_v3_setup_multiple_pads(sd1_pads,
ARRAY_SIZE(sd1_pads));
break;
case 1:
imx_iomux_v3_setup_multiple_pads(sd2_pads,
ARRAY_SIZE(sd2_pads));
break;
default:
printf("Warning: you configured more ESDHC controller"
"(%d) as supported by the board(2)\n",
CONFIG_SYS_FSL_ESDHC_NUM);
return -EINVAL;
}
ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
if (ret)
return ret;
}
return 0;
}
#endif
int board_early_init_f(void)
{
setup_iomux_uart();
setup_iomux_fec();
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
return 0;
}
#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
/* 4 bit bus width */
{"mmc0", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x12)},
{"mmc1", MAKE_CFGVAL(0x40, 0x20, 0x08, 0x12)},
{NULL, 0},
};
#endif
int board_late_init(void)
{
setup_i2c(1);
power_init();
#ifdef CONFIG_CMD_BMODE
add_board_boot_modes(board_boot_modes);
#endif
return 0;
}
int checkboard(void)
{
puts("Board: MX53EVK\n");
return 0;
}