upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
87 lines
2.4 KiB
87 lines
2.4 KiB
/*
|
|
* Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <miiphy.h>
|
|
|
|
#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
|
|
|
|
#define MV88E1116_LED_FCTRL_REG 10
|
|
#define MV88E1116_CPRSP_CR3_REG 21
|
|
#define MV88E1116_MAC_CTRL_REG 21
|
|
#define MV88E1116_PGADR_REG 22
|
|
#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
|
|
#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
|
|
|
|
void mv_phy_88e1116_init(const char *name)
|
|
{
|
|
u16 reg;
|
|
u16 devadr;
|
|
|
|
if (miiphy_set_current_dev(name))
|
|
return;
|
|
|
|
/* command to read PHY dev address */
|
|
if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
|
|
printf("Err..(%s) could not read PHY dev address\n", __func__);
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Enable RGMII delay on Tx and Rx for CPU port
|
|
* Ref: sec 4.7.2 of chip datasheet
|
|
*/
|
|
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
|
|
miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
|
|
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
|
|
miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
|
|
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
|
|
|
|
/* reset the phy */
|
|
miiphy_reset(name, devadr);
|
|
|
|
printf("88E1116 Initialized on %s\n", name);
|
|
}
|
|
#endif /* CONFIG_CMD_NET && CONFIG_RESET_PHY_R */
|
|
|
|
#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
|
|
int lacie_read_mac_address(uchar *mac_addr)
|
|
{
|
|
int ret;
|
|
ushort version;
|
|
|
|
/* I2C-0 for on-board EEPROM */
|
|
i2c_set_bus_num(0);
|
|
|
|
/* Check layout version for EEPROM data */
|
|
ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
|
|
CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
|
|
(uchar *) &version, 2);
|
|
if (ret != 0) {
|
|
printf("Error: failed to read I2C EEPROM @%02x\n",
|
|
CONFIG_SYS_I2C_EEPROM_ADDR);
|
|
return ret;
|
|
}
|
|
version = be16_to_cpu(version);
|
|
if (version < 1 || version > 3) {
|
|
printf("Error: unknown version %d for EEPROM data\n",
|
|
version);
|
|
return -1;
|
|
}
|
|
|
|
/* Read Ethernet MAC address from EEPROM */
|
|
ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 2,
|
|
CONFIG_SYS_I2C_EEPROM_ADDR_LEN, mac_addr, 6);
|
|
if (ret != 0)
|
|
printf("Error: failed to read I2C EEPROM @%02x\n",
|
|
CONFIG_SYS_I2C_EEPROM_ADDR);
|
|
return ret;
|
|
}
|
|
#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_EEPROM_ADDR */
|
|
|