upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
353 lines
9.8 KiB
353 lines
9.8 KiB
/*
|
|
* initcode.c - Initialize the processor. This is usually entails things
|
|
* like external memory, voltage regulators, etc... Note that this file
|
|
* cannot make any function calls as it may be executed all by itself by
|
|
* the Blackfin's bootrom in LDR format.
|
|
*
|
|
* Copyright (c) 2004-2008 Analog Devices Inc.
|
|
*
|
|
* Licensed under the GPL-2 or later.
|
|
*/
|
|
|
|
#include <config.h>
|
|
#include <asm/blackfin.h>
|
|
#include <asm/mach-common/bits/bootrom.h>
|
|
#include <asm/mach-common/bits/ebiu.h>
|
|
#include <asm/mach-common/bits/pll.h>
|
|
#include <asm/mach-common/bits/uart.h>
|
|
|
|
#define BFIN_IN_INITCODE
|
|
#include "serial.h"
|
|
|
|
__attribute__((always_inline))
|
|
static inline uint32_t serial_init(void)
|
|
{
|
|
#ifdef __ADSPBF54x__
|
|
# ifdef BFIN_BOOT_UART_USE_RTS
|
|
# define BFIN_UART_USE_RTS 1
|
|
# else
|
|
# define BFIN_UART_USE_RTS 0
|
|
# endif
|
|
if (BFIN_UART_USE_RTS && CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) {
|
|
size_t i;
|
|
|
|
/* force RTS rather than relying on auto RTS */
|
|
bfin_write_UART1_MCR(bfin_read_UART1_MCR() | FCPOL);
|
|
|
|
/* Wait for the line to clear up. We cannot rely on UART
|
|
* registers as none of them reflect the status of the RSR.
|
|
* Instead, we'll sleep for ~10 bit times at 9600 baud.
|
|
* We can precalc things here by assuming boot values for
|
|
* PLL rather than loading registers and calculating.
|
|
* baud = SCLK / (16 ^ (1 - EDBO) * Divisor)
|
|
* EDB0 = 0
|
|
* Divisor = (SCLK / baud) / 16
|
|
* SCLK = baud * 16 * Divisor
|
|
* SCLK = (0x14 * CONFIG_CLKIN_HZ) / 5
|
|
* CCLK = (16 * Divisor * 5) * (9600 / 10)
|
|
* In reality, this will probably be just about 1 second delay,
|
|
* so assuming 9600 baud is OK (both as a very low and too high
|
|
* speed as this will buffer things enough).
|
|
*/
|
|
#define _NUMBITS (10) /* how many bits to delay */
|
|
#define _LOWBAUD (9600) /* low baud rate */
|
|
#define _SCLK ((0x14 * CONFIG_CLKIN_HZ) / 5) /* SCLK based on PLL */
|
|
#define _DIVISOR ((_SCLK / _LOWBAUD) / 16) /* UART DLL/DLH */
|
|
#define _NUMINS (3) /* how many instructions in loop */
|
|
#define _CCLK (((16 * _DIVISOR * 5) * (_LOWBAUD / _NUMBITS)) / _NUMINS)
|
|
i = _CCLK;
|
|
while (i--)
|
|
asm volatile("" : : : "memory");
|
|
}
|
|
#endif
|
|
|
|
uint32_t old_baud = serial_early_get_baud();
|
|
|
|
if (BFIN_DEBUG_EARLY_SERIAL) {
|
|
serial_early_init();
|
|
|
|
/* If the UART is off, that means we need to program
|
|
* the baud rate ourselves initially.
|
|
*/
|
|
if (!old_baud) {
|
|
old_baud = CONFIG_BAUDRATE;
|
|
serial_early_set_baud(CONFIG_BAUDRATE);
|
|
}
|
|
}
|
|
|
|
return old_baud;
|
|
}
|
|
|
|
__attribute__((always_inline))
|
|
static inline void serial_deinit(void)
|
|
{
|
|
#ifdef __ADSPBF54x__
|
|
if (BFIN_UART_USE_RTS && CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART) {
|
|
/* clear forced RTS rather than relying on auto RTS */
|
|
bfin_write_UART1_MCR(bfin_read_UART1_MCR() & ~FCPOL);
|
|
}
|
|
#endif
|
|
}
|
|
|
|
/* We need to reset the baud rate when we have early debug turned on
|
|
* or when we are booting over the UART.
|
|
* XXX: we should fix this to calc the old baud and restore it rather
|
|
* than hardcoding it via CONFIG_LDR_LOAD_BAUD ... but we have
|
|
* to figure out how to avoid the division in the baud calc ...
|
|
*/
|
|
__attribute__((always_inline))
|
|
static inline void serial_reset_baud(uint32_t baud)
|
|
{
|
|
if (!BFIN_DEBUG_EARLY_SERIAL && CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
|
|
return;
|
|
|
|
#ifndef CONFIG_LDR_LOAD_BAUD
|
|
# define CONFIG_LDR_LOAD_BAUD 115200
|
|
#endif
|
|
|
|
if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
|
|
serial_early_set_baud(baud);
|
|
else if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART)
|
|
serial_early_set_baud(CONFIG_LDR_LOAD_BAUD);
|
|
else
|
|
serial_early_set_baud(CONFIG_BAUDRATE);
|
|
}
|
|
|
|
__attribute__((always_inline))
|
|
static inline void serial_putc(char c)
|
|
{
|
|
if (!BFIN_DEBUG_EARLY_SERIAL)
|
|
return;
|
|
|
|
if (c == '\n')
|
|
*pUART_THR = '\r';
|
|
|
|
*pUART_THR = c;
|
|
|
|
while (!(*pUART_LSR & TEMT))
|
|
continue;
|
|
}
|
|
|
|
|
|
/* Max SCLK can be 133MHz ... dividing that by 4 gives
|
|
* us a freq of 33MHz for SPI which should generally be
|
|
* slow enough for the slow reads the bootrom uses.
|
|
*/
|
|
#ifndef CONFIG_SPI_BAUD_INITBLOCK
|
|
# define CONFIG_SPI_BAUD_INITBLOCK 4
|
|
#endif
|
|
|
|
/* PLL_DIV defines */
|
|
#ifndef CONFIG_PLL_DIV_VAL
|
|
# if (CONFIG_CCLK_DIV == 1)
|
|
# define CONFIG_CCLK_ACT_DIV CCLK_DIV1
|
|
# elif (CONFIG_CCLK_DIV == 2)
|
|
# define CONFIG_CCLK_ACT_DIV CCLK_DIV2
|
|
# elif (CONFIG_CCLK_DIV == 4)
|
|
# define CONFIG_CCLK_ACT_DIV CCLK_DIV4
|
|
# elif (CONFIG_CCLK_DIV == 8)
|
|
# define CONFIG_CCLK_ACT_DIV CCLK_DIV8
|
|
# else
|
|
# define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
|
|
# endif
|
|
# define CONFIG_PLL_DIV_VAL (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV)
|
|
#endif
|
|
|
|
#ifndef CONFIG_PLL_LOCKCNT_VAL
|
|
# define CONFIG_PLL_LOCKCNT_VAL 0x0300
|
|
#endif
|
|
|
|
#ifndef CONFIG_PLL_CTL_VAL
|
|
# define CONFIG_PLL_CTL_VAL (SPORT_HYST | (CONFIG_VCO_MULT << 9))
|
|
#endif
|
|
|
|
#ifndef CONFIG_EBIU_RSTCTL_VAL
|
|
# define CONFIG_EBIU_RSTCTL_VAL 0 /* only MDDRENABLE is useful */
|
|
#endif
|
|
|
|
#ifndef CONFIG_EBIU_MBSCTL_VAL
|
|
# define CONFIG_EBIU_MBSCTL_VAL 0
|
|
#endif
|
|
|
|
/* Make sure our voltage value is sane so we don't blow up! */
|
|
#ifndef CONFIG_VR_CTL_VAL
|
|
# define BFIN_CCLK ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT) / CONFIG_CCLK_DIV)
|
|
# if defined(__ADSPBF533__) || defined(__ADSPBF532__) || defined(__ADSPBF531__)
|
|
# define CCLK_VLEV_120 400000000
|
|
# define CCLK_VLEV_125 533000000
|
|
# elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__)
|
|
# define CCLK_VLEV_120 401000000
|
|
# define CCLK_VLEV_125 401000000
|
|
# elif defined(__ADSPBF561__)
|
|
# define CCLK_VLEV_120 300000000
|
|
# define CCLK_VLEV_125 501000000
|
|
# endif
|
|
# if BFIN_CCLK < CCLK_VLEV_120
|
|
# define CONFIG_VR_CTL_VLEV VLEV_120
|
|
# elif BFIN_CCLK < CCLK_VLEV_125
|
|
# define CONFIG_VR_CTL_VLEV VLEV_125
|
|
# else
|
|
# define CONFIG_VR_CTL_VLEV VLEV_130
|
|
# endif
|
|
# if defined(__ADSPBF52x__) /* TBD; use default */
|
|
# undef CONFIG_VR_CTL_VLEV
|
|
# define CONFIG_VR_CTL_VLEV VLEV_110
|
|
# elif defined(__ADSPBF54x__) /* TBD; use default */
|
|
# undef CONFIG_VR_CTL_VLEV
|
|
# define CONFIG_VR_CTL_VLEV VLEV_120
|
|
# endif
|
|
|
|
# ifdef CONFIG_BFIN_MAC
|
|
# define CONFIG_VR_CTL_CLKBUF CLKBUFOE
|
|
# else
|
|
# define CONFIG_VR_CTL_CLKBUF 0
|
|
# endif
|
|
|
|
# if defined(__ADSPBF52x__)
|
|
# define CONFIG_VR_CTL_FREQ FREQ_1000
|
|
# else
|
|
# define CONFIG_VR_CTL_FREQ (GAIN_20 | FREQ_1000)
|
|
# endif
|
|
|
|
# define CONFIG_VR_CTL_VAL (CONFIG_VR_CTL_CLKBUF | CONFIG_VR_CTL_VLEV | CONFIG_VR_CTL_FREQ)
|
|
#endif
|
|
|
|
__attribute__((saveall))
|
|
void initcode(ADI_BOOT_DATA *bootstruct)
|
|
{
|
|
uint32_t old_baud = serial_init();
|
|
|
|
#ifdef CONFIG_HW_WATCHDOG
|
|
# ifndef CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE
|
|
# define CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE 20000
|
|
# endif
|
|
/* Program the watchdog with an initial timeout of ~20 seconds.
|
|
* Hopefully that should be long enough to load the u-boot LDR
|
|
* (from wherever) and then the common u-boot code can take over.
|
|
* In bypass mode, the start.S would have already set a much lower
|
|
* timeout, so don't clobber that.
|
|
*/
|
|
if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_BYPASS) {
|
|
bfin_write_WDOG_CNT(MSEC_TO_SCLK(CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE));
|
|
bfin_write_WDOG_CTL(0);
|
|
}
|
|
#endif
|
|
|
|
serial_putc('S');
|
|
|
|
/* Blackfin bootroms use the SPI slow read opcode instead of the SPI
|
|
* fast read, so we need to slow down the SPI clock a lot more during
|
|
* boot. Once we switch over to u-boot's SPI flash driver, we'll
|
|
* increase the speed appropriately.
|
|
*/
|
|
if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
|
|
#ifdef SPI0_BAUD
|
|
bfin_write_SPI0_BAUD(CONFIG_SPI_BAUD_INITBLOCK);
|
|
#else
|
|
bfin_write_SPI_BAUD(CONFIG_SPI_BAUD_INITBLOCK);
|
|
#endif
|
|
|
|
serial_putc('B');
|
|
|
|
/* Disable all peripheral wakeups except for the PLL event. */
|
|
#ifdef SIC_IWR0
|
|
bfin_write_SIC_IWR0(1);
|
|
bfin_write_SIC_IWR1(0);
|
|
# ifdef SIC_IWR2
|
|
bfin_write_SIC_IWR2(0);
|
|
# endif
|
|
#elif defined(SICA_IWR0)
|
|
bfin_write_SICA_IWR0(1);
|
|
bfin_write_SICA_IWR1(0);
|
|
#else
|
|
bfin_write_SIC_IWR(1);
|
|
#endif
|
|
|
|
serial_putc('L');
|
|
|
|
bfin_write_PLL_LOCKCNT(CONFIG_PLL_LOCKCNT_VAL);
|
|
|
|
serial_putc('A');
|
|
|
|
/* Only reprogram when needed to avoid triggering unnecessary
|
|
* PLL relock sequences.
|
|
*/
|
|
if (bfin_read_VR_CTL() != CONFIG_VR_CTL_VAL) {
|
|
serial_putc('!');
|
|
bfin_write_VR_CTL(CONFIG_VR_CTL_VAL);
|
|
asm("idle;");
|
|
}
|
|
|
|
serial_putc('C');
|
|
|
|
bfin_write_PLL_DIV(CONFIG_PLL_DIV_VAL);
|
|
|
|
serial_putc('K');
|
|
|
|
/* Only reprogram when needed to avoid triggering unnecessary
|
|
* PLL relock sequences.
|
|
*/
|
|
if (bfin_read_PLL_CTL() != CONFIG_PLL_CTL_VAL) {
|
|
serial_putc('!');
|
|
bfin_write_PLL_CTL(CONFIG_PLL_CTL_VAL);
|
|
asm("idle;");
|
|
}
|
|
|
|
/* Since we've changed the SCLK above, we may need to update
|
|
* the UART divisors (UART baud rates are based on SCLK).
|
|
*/
|
|
serial_reset_baud(old_baud);
|
|
|
|
serial_putc('F');
|
|
|
|
/* Program the async banks controller. */
|
|
bfin_write_EBIU_AMBCTL0(CONFIG_EBIU_AMBCTL0_VAL);
|
|
bfin_write_EBIU_AMBCTL1(CONFIG_EBIU_AMBCTL1_VAL);
|
|
bfin_write_EBIU_AMGCTL(CONFIG_EBIU_AMGCTL_VAL);
|
|
|
|
#ifdef EBIU_MODE
|
|
/* Not all parts have these additional MMRs. */
|
|
bfin_write_EBIU_MBSCTL(CONFIG_EBIU_MBSCTL_VAL);
|
|
bfin_write_EBIU_MODE(CONFIG_EBIU_MODE_VAL);
|
|
bfin_write_EBIU_FCTL(CONFIG_EBIU_FCTL_VAL);
|
|
#endif
|
|
|
|
serial_putc('I');
|
|
|
|
/* Program the external memory controller. */
|
|
#ifdef EBIU_RSTCTL
|
|
bfin_write_EBIU_RSTCTL(bfin_read_EBIU_RSTCTL() | 0x1 /*DDRSRESET*/ | CONFIG_EBIU_RSTCTL_VAL);
|
|
bfin_write_EBIU_DDRCTL0(CONFIG_EBIU_DDRCTL0_VAL);
|
|
bfin_write_EBIU_DDRCTL1(CONFIG_EBIU_DDRCTL1_VAL);
|
|
bfin_write_EBIU_DDRCTL2(CONFIG_EBIU_DDRCTL2_VAL);
|
|
# ifdef CONFIG_EBIU_DDRCTL3_VAL
|
|
/* default is disable, so don't need to force this */
|
|
bfin_write_EBIU_DDRCTL3(CONFIG_EBIU_DDRCTL3_VAL);
|
|
# endif
|
|
#else
|
|
bfin_write_EBIU_SDRRC(CONFIG_EBIU_SDRRC_VAL);
|
|
bfin_write_EBIU_SDBCTL(CONFIG_EBIU_SDBCTL_VAL);
|
|
bfin_write_EBIU_SDGCTL(CONFIG_EBIU_SDGCTL_VAL);
|
|
#endif
|
|
|
|
serial_putc('N');
|
|
|
|
/* Restore all peripheral wakeups. */
|
|
#ifdef SIC_IWR0
|
|
bfin_write_SIC_IWR0(-1);
|
|
bfin_write_SIC_IWR1(-1);
|
|
# ifdef SIC_IWR2
|
|
bfin_write_SIC_IWR2(-1);
|
|
# endif
|
|
#elif defined(SICA_IWR0)
|
|
bfin_write_SICA_IWR0(-1);
|
|
bfin_write_SICA_IWR1(-1);
|
|
#else
|
|
bfin_write_SIC_IWR(-1);
|
|
#endif
|
|
|
|
serial_putc('>');
|
|
serial_putc('\n');
|
|
|
|
serial_deinit();
|
|
}
|
|
|