upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/drivers/net/dm9000x.c

638 lines
16 KiB

/*
dm9000.c: Version 1.2 12/15/2003
A Davicom DM9000 ISA NIC fast Ethernet driver for Linux.
Copyright (C) 1997 Sten Wang
* SPDX-License-Identifier: GPL-2.0+
(C)Copyright 1997-1998 DAVICOM Semiconductor,Inc. All Rights Reserved.
V0.11 06/20/2001 REG_0A bit3=1, default enable BP with DA match
06/22/2001 Support DM9801 progrmming
E3: R25 = ((R24 + NF) & 0x00ff) | 0xf000
E4: R25 = ((R24 + NF) & 0x00ff) | 0xc200
R17 = (R17 & 0xfff0) | NF + 3
E5: R25 = ((R24 + NF - 3) & 0x00ff) | 0xc200
R17 = (R17 & 0xfff0) | NF
v1.00 modify by simon 2001.9.5
change for kernel 2.4.x
v1.1 11/09/2001 fix force mode bug
v1.2 03/18/2003 Weilun Huang <weilun_huang@davicom.com.tw>:
Fixed phy reset.
Added tx/rx 32 bit mode.
Cleaned up for kernel merge.
--------------------------------------
12/15/2003 Initial port to u-boot by
Sascha Hauer <saschahauer@web.de>
06/03/2008 Remy Bohmer <linux@bohmer.net>
- Fixed the driver to work with DM9000A.
(check on ISR receive status bit before reading the
FIFO as described in DM9000 programming guide and
application notes)
- Added autodetect of databus width.
- Made debug code compile again.
- Adapt eth_send such that it matches the DM9000*
application notes. Needed to make it work properly
for DM9000A.
- Adapted reset procedure to match DM9000 application
notes (i.e. double reset)
- some minor code cleanups
These changes are tested with DM9000{A,EP,E} together
with a 200MHz Atmel AT91SAM9261 core
TODO: external MII is not functional, only internal at the moment.
*/
#include <common.h>
#include <command.h>
#include <net.h>
#include <asm/io.h>
#include <dm9000.h>
#include "dm9000x.h"
/* Board/System/Debug information/definition ---------------- */
/* #define CONFIG_DM9000_DEBUG */
#ifdef CONFIG_DM9000_DEBUG
#define DM9000_DBG(fmt,args...) printf(fmt, ##args)
#define DM9000_DMP_PACKET(func,packet,length) \
do { \
int i; \
printf("%s: length: %d\n", func, length); \
for (i = 0; i < length; i++) { \
if (i % 8 == 0) \
printf("\n%s: %02x: ", func, i); \
printf("%02x ", ((unsigned char *) packet)[i]); \
} printf("\n"); \
} while(0)
#else
#define DM9000_DBG(fmt,args...)
#define DM9000_DMP_PACKET(func,packet,length)
#endif
/* Structure/enum declaration ------------------------------- */
typedef struct board_info {
u32 runt_length_counter; /* counter: RX length < 64byte */
u32 long_length_counter; /* counter: RX length > 1514byte */
u32 reset_counter; /* counter: RESET */
u32 reset_tx_timeout; /* RESET caused by TX Timeout */
u32 reset_rx_status; /* RESET caused by RX Statsus wrong */
u16 tx_pkt_cnt;
u16 queue_start_addr;
u16 dbug_cnt;
u8 phy_addr;
u8 device_wait_reset; /* device state */
unsigned char srom[128];
void (*outblk)(volatile void *data_ptr, int count);
void (*inblk)(void *data_ptr, int count);
void (*rx_status)(u16 *RxStatus, u16 *RxLen);
struct eth_device netdev;
} board_info_t;
static board_info_t dm9000_info;
/* function declaration ------------------------------------- */
static int dm9000_probe(void);
static u16 dm9000_phy_read(int);
static void dm9000_phy_write(int, u16);
static u8 DM9000_ior(int);
static void DM9000_iow(int reg, u8 value);
/* DM9000 network board routine ---------------------------- */
#ifndef CONFIG_DM9000_BYTE_SWAPPED
#define DM9000_outb(d,r) writeb(d, (volatile u8 *)(r))
#define DM9000_outw(d,r) writew(d, (volatile u16 *)(r))
#define DM9000_outl(d,r) writel(d, (volatile u32 *)(r))
#define DM9000_inb(r) readb((volatile u8 *)(r))
#define DM9000_inw(r) readw((volatile u16 *)(r))
#define DM9000_inl(r) readl((volatile u32 *)(r))
#else
#define DM9000_outb(d, r) __raw_writeb(d, r)
#define DM9000_outw(d, r) __raw_writew(d, r)
#define DM9000_outl(d, r) __raw_writel(d, r)
#define DM9000_inb(r) __raw_readb(r)
#define DM9000_inw(r) __raw_readw(r)
#define DM9000_inl(r) __raw_readl(r)
#endif
#ifdef CONFIG_DM9000_DEBUG
static void
dump_regs(void)
{
DM9000_DBG("\n");
DM9000_DBG("NCR (0x00): %02x\n", DM9000_ior(0));
DM9000_DBG("NSR (0x01): %02x\n", DM9000_ior(1));
DM9000_DBG("TCR (0x02): %02x\n", DM9000_ior(2));
DM9000_DBG("TSRI (0x03): %02x\n", DM9000_ior(3));
DM9000_DBG("TSRII (0x04): %02x\n", DM9000_ior(4));
DM9000_DBG("RCR (0x05): %02x\n", DM9000_ior(5));
DM9000_DBG("RSR (0x06): %02x\n", DM9000_ior(6));
DM9000_DBG("ISR (0xFE): %02x\n", DM9000_ior(DM9000_ISR));
DM9000_DBG("\n");
}
#endif
static void dm9000_outblk_8bit(volatile void *data_ptr, int count)
{
int i;
for (i = 0; i < count; i++)
DM9000_outb((((u8 *) data_ptr)[i] & 0xff), DM9000_DATA);
}
static void dm9000_outblk_16bit(volatile void *data_ptr, int count)
{
int i;
u32 tmplen = (count + 1) / 2;
for (i = 0; i < tmplen; i++)
DM9000_outw(((u16 *) data_ptr)[i], DM9000_DATA);
}
static void dm9000_outblk_32bit(volatile void *data_ptr, int count)
{
int i;
u32 tmplen = (count + 3) / 4;
for (i = 0; i < tmplen; i++)
DM9000_outl(((u32 *) data_ptr)[i], DM9000_DATA);
}
static void dm9000_inblk_8bit(void *data_ptr, int count)
{
int i;
for (i = 0; i < count; i++)
((u8 *) data_ptr)[i] = DM9000_inb(DM9000_DATA);
}
static void dm9000_inblk_16bit(void *data_ptr, int count)
{
int i;
u32 tmplen = (count + 1) / 2;
for (i = 0; i < tmplen; i++)
((u16 *) data_ptr)[i] = DM9000_inw(DM9000_DATA);
}
static void dm9000_inblk_32bit(void *data_ptr, int count)
{
int i;
u32 tmplen = (count + 3) / 4;
for (i = 0; i < tmplen; i++)
((u32 *) data_ptr)[i] = DM9000_inl(DM9000_DATA);
}
static void dm9000_rx_status_32bit(u16 *RxStatus, u16 *RxLen)
{
u32 tmpdata;
DM9000_outb(DM9000_MRCMD, DM9000_IO);
tmpdata = DM9000_inl(DM9000_DATA);
*RxStatus = __le16_to_cpu(tmpdata);
*RxLen = __le16_to_cpu(tmpdata >> 16);
}
static void dm9000_rx_status_16bit(u16 *RxStatus, u16 *RxLen)
{
DM9000_outb(DM9000_MRCMD, DM9000_IO);
*RxStatus = __le16_to_cpu(DM9000_inw(DM9000_DATA));
*RxLen = __le16_to_cpu(DM9000_inw(DM9000_DATA));
}
static void dm9000_rx_status_8bit(u16 *RxStatus, u16 *RxLen)
{
DM9000_outb(DM9000_MRCMD, DM9000_IO);
*RxStatus =
__le16_to_cpu(DM9000_inb(DM9000_DATA) +
(DM9000_inb(DM9000_DATA) << 8));
*RxLen =
__le16_to_cpu(DM9000_inb(DM9000_DATA) +
(DM9000_inb(DM9000_DATA) << 8));
}
/*
Search DM9000 board, allocate space and register it
*/
int
dm9000_probe(void)
{
u32 id_val;
id_val = DM9000_ior(DM9000_VIDL);
id_val |= DM9000_ior(DM9000_VIDH) << 8;
id_val |= DM9000_ior(DM9000_PIDL) << 16;
id_val |= DM9000_ior(DM9000_PIDH) << 24;
if (id_val == DM9000_ID) {
printf("dm9000 i/o: 0x%x, id: 0x%x \n", CONFIG_DM9000_BASE,
id_val);
return 0;
} else {
printf("dm9000 not found at 0x%08x id: 0x%08x\n",
CONFIG_DM9000_BASE, id_val);
return -1;
}
}
/* General Purpose dm9000 reset routine */
static void
dm9000_reset(void)
{
DM9000_DBG("resetting DM9000\n");
/* Reset DM9000,
see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 */
/* DEBUG: Make all GPIO0 outputs, all others inputs */
DM9000_iow(DM9000_GPCR, GPCR_GPIO0_OUT);
/* Step 1: Power internal PHY by writing 0 to GPIO0 pin */
DM9000_iow(DM9000_GPR, 0);
/* Step 2: Software reset */
DM9000_iow(DM9000_NCR, (NCR_LBK_INT_MAC | NCR_RST));
do {
DM9000_DBG("resetting the DM9000, 1st reset\n");
udelay(25); /* Wait at least 20 us */
} while (DM9000_ior(DM9000_NCR) & 1);
DM9000_iow(DM9000_NCR, 0);
DM9000_iow(DM9000_NCR, (NCR_LBK_INT_MAC | NCR_RST)); /* Issue a second reset */
do {
DM9000_DBG("resetting the DM9000, 2nd reset\n");
udelay(25); /* Wait at least 20 us */
} while (DM9000_ior(DM9000_NCR) & 1);
/* Check whether the ethernet controller is present */
if ((DM9000_ior(DM9000_PIDL) != 0x0) ||
(DM9000_ior(DM9000_PIDH) != 0x90))
printf("ERROR: resetting DM9000 -> not responding\n");
}
/* Initialize dm9000 board
*/
static int dm9000_init(struct eth_device *dev, bd_t *bd)
{
int i, oft, lnk;
u8 io_mode;
struct board_info *db = &dm9000_info;
DM9000_DBG("%s\n", __func__);
/* RESET device */
dm9000_reset();
if (dm9000_probe() < 0)
return -1;
/* Auto-detect 8/16/32 bit mode, ISR Bit 6+7 indicate bus width */
io_mode = DM9000_ior(DM9000_ISR) >> 6;
switch (io_mode) {
case 0x0: /* 16-bit mode */
printf("DM9000: running in 16 bit mode\n");
db->outblk = dm9000_outblk_16bit;
db->inblk = dm9000_inblk_16bit;
db->rx_status = dm9000_rx_status_16bit;
break;
case 0x01: /* 32-bit mode */
printf("DM9000: running in 32 bit mode\n");
db->outblk = dm9000_outblk_32bit;
db->inblk = dm9000_inblk_32bit;
db->rx_status = dm9000_rx_status_32bit;
break;
case 0x02: /* 8 bit mode */
printf("DM9000: running in 8 bit mode\n");
db->outblk = dm9000_outblk_8bit;
db->inblk = dm9000_inblk_8bit;
db->rx_status = dm9000_rx_status_8bit;
break;
default:
/* Assume 8 bit mode, will probably not work anyway */
printf("DM9000: Undefined IO-mode:0x%x\n", io_mode);
db->outblk = dm9000_outblk_8bit;
db->inblk = dm9000_inblk_8bit;
db->rx_status = dm9000_rx_status_8bit;
break;
}
/* Program operating register, only internal phy supported */
DM9000_iow(DM9000_NCR, 0x0);
/* TX Polling clear */
DM9000_iow(DM9000_TCR, 0);
/* Less 3Kb, 200us */
DM9000_iow(DM9000_BPTR, BPTR_BPHW(3) | BPTR_JPT_600US);
/* Flow Control : High/Low Water */
DM9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8));
/* SH FIXME: This looks strange! Flow Control */
DM9000_iow(DM9000_FCR, 0x0);
/* Special Mode */
DM9000_iow(DM9000_SMCR, 0);
/* clear TX status */
DM9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END);
/* Clear interrupt status */
DM9000_iow(DM9000_ISR, ISR_ROOS | ISR_ROS | ISR_PTS | ISR_PRS);
printf("MAC: %pM\n", dev->enetaddr);
if (!is_valid_ethaddr(dev->enetaddr)) {
printf("WARNING: Bad MAC address (uninitialized EEPROM?)\n");
}
/* fill device MAC address registers */
for (i = 0, oft = DM9000_PAR; i < 6; i++, oft++)
DM9000_iow(oft, dev->enetaddr[i]);
for (i = 0, oft = 0x16; i < 8; i++, oft++)
DM9000_iow(oft, 0xff);
/* read back mac, just to be sure */
for (i = 0, oft = 0x10; i < 6; i++, oft++)
DM9000_DBG("%02x:", DM9000_ior(oft));
DM9000_DBG("\n");
/* Activate DM9000 */
/* RX enable */
DM9000_iow(DM9000_RCR, RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN);
/* Enable TX/RX interrupt mask */
DM9000_iow(DM9000_IMR, IMR_PAR);
i = 0;
while (!(dm9000_phy_read(1) & 0x20)) { /* autonegation complete bit */
udelay(1000);
i++;
if (i == 10000) {
printf("could not establish link\n");
return 0;
}
}
/* see what we've got */
lnk = dm9000_phy_read(17) >> 12;
printf("operating at ");
switch (lnk) {
case 1:
printf("10M half duplex ");
break;
case 2:
printf("10M full duplex ");
break;
case 4:
printf("100M half duplex ");
break;
case 8:
printf("100M full duplex ");
break;
default:
printf("unknown: %d ", lnk);
break;
}
printf("mode\n");
return 0;
}
/*
Hardware start transmission.
Send a packet to media from the upper layer.
*/
static int dm9000_send(struct eth_device *netdev, void *packet, int length)
{
int tmo;
struct board_info *db = &dm9000_info;
DM9000_DMP_PACKET(__func__ , packet, length);
DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */
/* Move data to DM9000 TX RAM */
DM9000_outb(DM9000_MWCMD, DM9000_IO); /* Prepare for TX-data */
/* push the data to the TX-fifo */
(db->outblk)(packet, length);
/* Set TX length to DM9000 */
DM9000_iow(DM9000_TXPLL, length & 0xff);
DM9000_iow(DM9000_TXPLH, (length >> 8) & 0xff);
/* Issue TX polling command */
DM9000_iow(DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */
/* wait for end of transmission */
tmo = get_timer(0) + 5 * CONFIG_SYS_HZ;
while ( !(DM9000_ior(DM9000_NSR) & (NSR_TX1END | NSR_TX2END)) ||
!(DM9000_ior(DM9000_ISR) & IMR_PTM) ) {
if (get_timer(0) >= tmo) {
printf("transmission timeout\n");
break;
}
}
DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */
DM9000_DBG("transmit done\n\n");
return 0;
}
/*
Stop the interface.
The interface is stopped when it is brought.
*/
static void dm9000_halt(struct eth_device *netdev)
{
DM9000_DBG("%s\n", __func__);
/* RESET devie */
dm9000_phy_write(0, 0x8000); /* PHY RESET */
DM9000_iow(DM9000_GPR, 0x01); /* Power-Down PHY */
DM9000_iow(DM9000_IMR, 0x80); /* Disable all interrupt */
DM9000_iow(DM9000_RCR, 0x00); /* Disable RX */
}
/*
Received a packet and pass to upper layer
*/
static int dm9000_rx(struct eth_device *netdev)
{
u8 rxbyte;
u8 *rdptr = (u8 *)net_rx_packets[0];
u16 RxStatus, RxLen = 0;
struct board_info *db = &dm9000_info;
/* Check packet ready or not, we must check
the ISR status first for DM9000A */
if (!(DM9000_ior(DM9000_ISR) & 0x01)) /* Rx-ISR bit must be set. */
return 0;
DM9000_iow(DM9000_ISR, 0x01); /* clear PR status latched in bit 0 */
/* There is _at least_ 1 package in the fifo, read them all */
for (;;) {
DM9000_ior(DM9000_MRCMDX); /* Dummy read */
/* Get most updated data,
only look at bits 0:1, See application notes DM9000 */
rxbyte = DM9000_inb(DM9000_DATA) & 0x03;
/* Status check: this byte must be 0 or 1 */
if (rxbyte > DM9000_PKT_RDY) {
DM9000_iow(DM9000_RCR, 0x00); /* Stop Device */
DM9000_iow(DM9000_ISR, 0x80); /* Stop INT request */
printf("DM9000 error: status check fail: 0x%x\n",
rxbyte);
return 0;
}
if (rxbyte != DM9000_PKT_RDY)
return 0; /* No packet received, ignore */
DM9000_DBG("receiving packet\n");
/* A packet ready now & Get status/length */
(db->rx_status)(&RxStatus, &RxLen);
DM9000_DBG("rx status: 0x%04x rx len: %d\n", RxStatus, RxLen);
/* Move data from DM9000 */
/* Read received packet from RX SRAM */
(db->inblk)(rdptr, RxLen);
if ((RxStatus & 0xbf00) || (RxLen < 0x40)
|| (RxLen > DM9000_PKT_MAX)) {
if (RxStatus & 0x100) {
printf("rx fifo error\n");
}
if (RxStatus & 0x200) {
printf("rx crc error\n");
}
if (RxStatus & 0x8000) {
printf("rx length error\n");
}
if (RxLen > DM9000_PKT_MAX) {
printf("rx length too big\n");
dm9000_reset();
}
} else {
DM9000_DMP_PACKET(__func__ , rdptr, RxLen);
DM9000_DBG("passing packet to upper layer\n");
net_process_received_packet(net_rx_packets[0], RxLen);
}
}
return 0;
}
/*
Read a word data from SROM
*/
#if !defined(CONFIG_DM9000_NO_SROM)
void dm9000_read_srom_word(int offset, u8 *to)
{
DM9000_iow(DM9000_EPAR, offset);
DM9000_iow(DM9000_EPCR, 0x4);
udelay(8000);
DM9000_iow(DM9000_EPCR, 0x0);
to[0] = DM9000_ior(DM9000_EPDRL);
to[1] = DM9000_ior(DM9000_EPDRH);
}
void dm9000_write_srom_word(int offset, u16 val)
{
DM9000_iow(DM9000_EPAR, offset);
DM9000_iow(DM9000_EPDRH, ((val >> 8) & 0xff));
DM9000_iow(DM9000_EPDRL, (val & 0xff));
DM9000_iow(DM9000_EPCR, 0x12);
udelay(8000);
DM9000_iow(DM9000_EPCR, 0);
}
#endif
static void dm9000_get_enetaddr(struct eth_device *dev)
{
#if !defined(CONFIG_DM9000_NO_SROM)
int i;
for (i = 0; i < 3; i++)
dm9000_read_srom_word(i, dev->enetaddr + (2 * i));
#endif
}
/*
Read a byte from I/O port
*/
static u8
DM9000_ior(int reg)
{
DM9000_outb(reg, DM9000_IO);
return DM9000_inb(DM9000_DATA);
}
/*
Write a byte to I/O port
*/
static void
DM9000_iow(int reg, u8 value)
{
DM9000_outb(reg, DM9000_IO);
DM9000_outb(value, DM9000_DATA);
}
/*
Read a word from phyxcer
*/
static u16
dm9000_phy_read(int reg)
{
u16 val;
/* Fill the phyxcer register into REG_0C */
DM9000_iow(DM9000_EPAR, DM9000_PHY | reg);
DM9000_iow(DM9000_EPCR, 0xc); /* Issue phyxcer read command */
udelay(100); /* Wait read complete */
DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer read command */
val = (DM9000_ior(DM9000_EPDRH) << 8) | DM9000_ior(DM9000_EPDRL);
/* The read data keeps on REG_0D & REG_0E */
DM9000_DBG("dm9000_phy_read(0x%x): 0x%x\n", reg, val);
return val;
}
/*
Write a word to phyxcer
*/
static void
dm9000_phy_write(int reg, u16 value)
{
/* Fill the phyxcer register into REG_0C */
DM9000_iow(DM9000_EPAR, DM9000_PHY | reg);
/* Fill the written data into REG_0D & REG_0E */
DM9000_iow(DM9000_EPDRL, (value & 0xff));
DM9000_iow(DM9000_EPDRH, ((value >> 8) & 0xff));
DM9000_iow(DM9000_EPCR, 0xa); /* Issue phyxcer write command */
udelay(500); /* Wait write complete */
DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer write command */
DM9000_DBG("dm9000_phy_write(reg:0x%x, value:0x%x)\n", reg, value);
}
int dm9000_initialize(bd_t *bis)
{
struct eth_device *dev = &(dm9000_info.netdev);
/* Load MAC address from EEPROM */
dm9000_get_enetaddr(dev);
dev->init = dm9000_init;
dev->halt = dm9000_halt;
dev->send = dm9000_send;
dev->recv = dm9000_rx;
strcpy(dev->name, "dm9000");
eth_register(dev);
return 0;
}