upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/phytec/pcm051/board.c

256 lines
6.2 KiB

/*
* board.c
*
* Board functions for Phytec phyCORE-AM335x (pcm051) based boards
*
* Copyright (C) 2013 Lemonage Software GmbH
* Author Lars Poeschel <poeschel@lemonage.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <errno.h>
#include <spl.h>
#include <asm/arch/cpu.h>
#include <asm/arch/hardware.h>
#include <asm/arch/omap.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
#include <asm/io.h>
#include <asm/emif.h>
#include <asm/gpio.h>
#include <i2c.h>
#include <miiphy.h>
#include <cpsw.h>
#include "board.h"
DECLARE_GLOBAL_DATA_PTR;
/* MII mode defines */
#define RMII_RGMII2_MODE_ENABLE 0x49
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
#ifdef CONFIG_SPL_BUILD
/* DDR RAM defines */
#define DDR_CLK_MHZ 303 /* DDR_DPLL_MULT value */
#define OSC (V_OSCK/1000000)
const struct dpll_params dpll_ddr = {
DDR_CLK_MHZ, OSC-1, 1, -1, -1, -1, -1};
const struct dpll_params *get_dpll_ddr_params(void)
{
return &dpll_ddr;
}
#ifdef CONFIG_REV1
const struct ctrl_ioregs ioregs = {
.cm0ioctl = MT41J256M8HX15E_IOCTRL_VALUE,
.cm1ioctl = MT41J256M8HX15E_IOCTRL_VALUE,
.cm2ioctl = MT41J256M8HX15E_IOCTRL_VALUE,
.dt0ioctl = MT41J256M8HX15E_IOCTRL_VALUE,
.dt1ioctl = MT41J256M8HX15E_IOCTRL_VALUE,
};
static const struct ddr_data ddr3_data = {
.datardsratio0 = MT41J256M8HX15E_RD_DQS,
.datawdsratio0 = MT41J256M8HX15E_WR_DQS,
.datafwsratio0 = MT41J256M8HX15E_PHY_FIFO_WE,
.datawrsratio0 = MT41J256M8HX15E_PHY_WR_DATA,
};
static const struct cmd_control ddr3_cmd_ctrl_data = {
.cmd0csratio = MT41J256M8HX15E_RATIO,
.cmd0iclkout = MT41J256M8HX15E_INVERT_CLKOUT,
.cmd1csratio = MT41J256M8HX15E_RATIO,
.cmd1iclkout = MT41J256M8HX15E_INVERT_CLKOUT,
.cmd2csratio = MT41J256M8HX15E_RATIO,
.cmd2iclkout = MT41J256M8HX15E_INVERT_CLKOUT,
};
static struct emif_regs ddr3_emif_reg_data = {
.sdram_config = MT41J256M8HX15E_EMIF_SDCFG,
.ref_ctrl = MT41J256M8HX15E_EMIF_SDREF,
.sdram_tim1 = MT41J256M8HX15E_EMIF_TIM1,
.sdram_tim2 = MT41J256M8HX15E_EMIF_TIM2,
.sdram_tim3 = MT41J256M8HX15E_EMIF_TIM3,
.zq_config = MT41J256M8HX15E_ZQ_CFG,
.emif_ddr_phy_ctlr_1 = MT41J256M8HX15E_EMIF_READ_LATENCY |
PHY_EN_DYN_PWRDN,
};
void sdram_init(void)
{
config_ddr(DDR_CLK_MHZ, &ioregs, &ddr3_data,
&ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
}
#else
const struct ctrl_ioregs ioregs = {
.cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
};
static const struct ddr_data ddr3_data = {
.datardsratio0 = MT41K256M16HA125E_RD_DQS,
.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
};
static const struct cmd_control ddr3_cmd_ctrl_data = {
.cmd0csratio = MT41K256M16HA125E_RATIO,
.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
.cmd1csratio = MT41K256M16HA125E_RATIO,
.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
.cmd2csratio = MT41K256M16HA125E_RATIO,
.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
};
static struct emif_regs ddr3_emif_reg_data = {
.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
.zq_config = MT41K256M16HA125E_ZQ_CFG,
.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY |
PHY_EN_DYN_PWRDN,
};
void sdram_init(void)
{
config_ddr(DDR_CLK_MHZ, &ioregs, &ddr3_data,
&ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
}
#endif
void set_uart_mux_conf(void)
{
enable_uart0_pin_mux();
}
void set_mux_conf_regs(void)
{
/* Initalize the board header */
enable_i2c0_pin_mux();
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
enable_board_pin_mux();
}
#endif
/*
* Basic board specific setup. Pinmux has been handled already.
*/
int board_init(void)
{
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
return 0;
}
#ifdef CONFIG_DRIVER_TI_CPSW
static void cpsw_control(int enabled)
{
/* VTP can be added here */
return;
}
static struct cpsw_slave_data cpsw_slaves[] = {
{
.slave_reg_ofs = 0x208,
.sliver_reg_ofs = 0xd80,
.phy_addr = 0,
.phy_if = PHY_INTERFACE_MODE_RGMII,
},
{
.slave_reg_ofs = 0x308,
.sliver_reg_ofs = 0xdc0,
.phy_addr = 1,
.phy_if = PHY_INTERFACE_MODE_RGMII,
},
};
static struct cpsw_platform_data cpsw_data = {
.mdio_base = CPSW_MDIO_BASE,
.cpsw_base = CPSW_BASE,
.mdio_div = 0xff,
.channels = 8,
.cpdma_reg_ofs = 0x800,
.slaves = 1,
.slave_data = cpsw_slaves,
.ale_reg_ofs = 0xd00,
.ale_entries = 1024,
.host_port_reg_ofs = 0x108,
.hw_stats_reg_ofs = 0x900,
.bd_ram_ofs = 0x2000,
.mac_control = (1 << 5),
.control = cpsw_control,
.host_port_num = 0,
.version = CPSW_CTRL_VERSION_2,
};
#endif
#if defined(CONFIG_DRIVER_TI_CPSW) || \
(defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET))
int board_eth_init(bd_t *bis)
{
int rv, n = 0;
#ifdef CONFIG_DRIVER_TI_CPSW
uint8_t mac_addr[6];
uint32_t mac_hi, mac_lo;
if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
printf("<ethaddr> not set. Reading from E-fuse\n");
/* try reading mac address from efuse */
mac_lo = readl(&cdev->macid0l);
mac_hi = readl(&cdev->macid0h);
mac_addr[0] = mac_hi & 0xFF;
mac_addr[1] = (mac_hi & 0xFF00) >> 8;
mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
mac_addr[4] = mac_lo & 0xFF;
mac_addr[5] = (mac_lo & 0xFF00) >> 8;
if (is_valid_ether_addr(mac_addr))
eth_setenv_enetaddr("ethaddr", mac_addr);
else
goto try_usbether;
}
writel(RMII_RGMII2_MODE_ENABLE, &cdev->miisel);
rv = cpsw_register(&cpsw_data);
if (rv < 0)
printf("Error %d registering CPSW switch\n", rv);
else
n += rv;
try_usbether:
#endif
#if defined(CONFIG_USB_ETHER) && !defined(CONFIG_SPL_BUILD)
rv = usb_eth_initialize(bis);
if (rv < 0)
printf("Error %d registering USB_ETHER\n", rv);
else
n += rv;
#endif
return n;
}
#endif