upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
1929 lines
61 KiB
1929 lines
61 KiB
/*
|
|
* (C) Copyright 2005-2007
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/ppc4xx-gpio.h>
|
|
#include <spd_sdram.h>
|
|
#include <asm/ppc440.h>
|
|
#include "bamboo.h"
|
|
|
|
void ext_bus_cntlr_init(void);
|
|
void configure_ppc440ep_pins(void);
|
|
int is_nand_selected(void);
|
|
|
|
#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL))
|
|
/*************************************************************************
|
|
*
|
|
* Bamboo has one bank onboard sdram (plus DIMM)
|
|
*
|
|
* Fixed memory is composed of :
|
|
* MT46V16M16TG-75 from Micron (x 2), 256Mb, 16 M x16, DDR266,
|
|
* 13 row add bits, 10 column add bits (but 12 row used only).
|
|
* ECC device: MT46V16M8TG-75 from Micron (x 1), 128Mb, x8, DDR266,
|
|
* 12 row add bits, 10 column add bits.
|
|
* Prepare a subset (only the used ones) of SPD data
|
|
*
|
|
* Note : if the ECC is enabled (SDRAM_ECC_ENABLE) the size of
|
|
* the corresponding bank is divided by 2 due to number of Row addresses
|
|
* 12 in the ECC module
|
|
*
|
|
* Assumes: 64 MB, ECC, non-registered
|
|
* PLB @ 133 MHz
|
|
*
|
|
************************************************************************/
|
|
const unsigned char cfg_simulate_spd_eeprom[128] = {
|
|
0x80, /* number of SPD bytes used: 128 */
|
|
0x08, /* total number bytes in SPD device = 256 */
|
|
0x07, /* DDR ram */
|
|
#ifdef CONFIG_DDR_ECC
|
|
0x0C, /* num Row Addr: 12 */
|
|
#else
|
|
0x0D, /* num Row Addr: 13 */
|
|
#endif
|
|
0x09, /* numColAddr: 9 */
|
|
0x01, /* numBanks: 1 */
|
|
0x20, /* Module data width: 32 bits */
|
|
0x00, /* Module data width continued: +0 */
|
|
0x04, /* 2.5 Volt */
|
|
0x75, /* SDRAM Cycle Time (cas latency 2.5) = 7.5 ns */
|
|
0x00, /* SDRAM Access from clock */
|
|
#ifdef CONFIG_DDR_ECC
|
|
0x02, /* ECC ON : 02 OFF : 00 */
|
|
#else
|
|
0x00, /* ECC ON : 02 OFF : 00 */
|
|
#endif
|
|
0x82, /* refresh Rate Type: Normal (7.8us) + Self refresh */
|
|
0,
|
|
0,
|
|
0x01, /* wcsbc = 1 */
|
|
0,
|
|
0,
|
|
0x0C, /* casBit (2,2.5) */
|
|
0,
|
|
0,
|
|
0x00, /* not registered: 0 registered : 0x02*/
|
|
0,
|
|
0xA0, /* SDRAM Cycle Time (cas latency 2) = 10 ns */
|
|
0,
|
|
0x00, /* SDRAM Cycle Time (cas latency 1.5) = N.A */
|
|
0,
|
|
0x50, /* tRpNs = 20 ns */
|
|
0,
|
|
0x50, /* tRcdNs = 20 ns */
|
|
45, /* tRasNs */
|
|
#ifdef CONFIG_DDR_ECC
|
|
0x08, /* bankSizeID: 32MB */
|
|
#else
|
|
0x10, /* bankSizeID: 64MB */
|
|
#endif
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0,
|
|
0
|
|
};
|
|
#endif
|
|
|
|
#if 0
|
|
{ /* GPIO Alternate1 Alternate2 Alternate3 */
|
|
{
|
|
/* GPIO Core 0 */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_0 -> EBC_ADDR(7) DMA_REQ(2) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_1 -> EBC_ADDR(6) DMA_ACK(2) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_2 -> EBC_ADDR(5) DMA_EOT/TC(2) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_3 -> EBC_ADDR(4) DMA_REQ(3) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_4 -> EBC_ADDR(3) DMA_ACK(3) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_5 ................. */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_6 -> EBC_CS_N(1) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_7 -> EBC_CS_N(2) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_8 -> EBC_CS_N(3) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_ALT1 }, /* GPIO0_9 -> EBC_CS_N(4) */
|
|
{ GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO0_10 -> EBC_CS_N(5) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_11 -> EBC_BUS_ERR */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_12 -> ZII_p0Rxd(0) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_13 -> ZII_p0Rxd(1) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_14 -> ZII_p0Rxd(2) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_15 -> ZII_p0Rxd(3) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_16 -> ZII_p0Txd(0) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_17 -> ZII_p0Txd(1) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_18 -> ZII_p0Txd(2) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_19 -> ZII_p0Txd(3) */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_20 -> ZII_p0Rx_er */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_21 -> ZII_p0Rx_dv */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_22 -> ZII_p0RxCrs */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_23 -> ZII_p0Tx_er */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_24 -> ZII_p0Tx_en */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_25 -> ZII_p0Col */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_26 -> USB2D_RXVALID */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_27 -> EXT_EBC_REQ USB2D_RXERROR */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_28 -> USB2D_TXVALID */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_29 -> EBC_EXT_HDLA USB2D_PAD_SUSPNDM */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_30 -> EBC_EXT_ACK USB2D_XCVRSELECT */
|
|
{ GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_31 -> EBC_EXR_BUSREQ USB2D_TERMSELECT */
|
|
},
|
|
{
|
|
/* GPIO Core 1 */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_0 -> USB2D_OPMODE0 */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_1 -> USB2D_OPMODE1 */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_2 -> UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_3 -> UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_4 -> UART0_8PIN_CTS_N UART3_SIN */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_5 -> UART0_RTS_N */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_6 -> UART0_DTR_N UART1_SOUT */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_7 -> UART0_RI_N UART1_SIN */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_8 -> UIC_IRQ(0) */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_9 -> UIC_IRQ(1) */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_10 -> UIC_IRQ(2) */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_11 -> UIC_IRQ(3) */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_12 -> UIC_IRQ(4) DMA_ACK(1) */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_13 -> UIC_IRQ(6) DMA_EOT/TC(1) */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_14 -> UIC_IRQ(7) DMA_REQ(0) */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_15 -> UIC_IRQ(8) DMA_ACK(0) */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_16 -> UIC_IRQ(9) DMA_EOT/TC(0) */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_17 -> - */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_18 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_19 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_20 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_21 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_22 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_23 -> \ Can be unselected thru TraceSelect Bit */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_24 -> / in PowerPC440EP Chip */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_25 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_26 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_27 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_28 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_29 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_30 -> | */
|
|
{ GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_31 -> - */
|
|
}
|
|
};
|
|
#endif
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| EBC Devices Characteristics
|
|
| Peripheral Bank Access Parameters - EBC0_BnAP
|
|
| Peripheral Bank Configuration Register - EBC0_BnCR
|
|
+----------------------------------------------------------------------------*/
|
|
/* Small Flash */
|
|
#define EBC0_BNAP_SMALL_FLASH \
|
|
EBC0_BNAP_BME_DISABLED | \
|
|
EBC0_BNAP_TWT_ENCODE(6) | \
|
|
EBC0_BNAP_CSN_ENCODE(0) | \
|
|
EBC0_BNAP_OEN_ENCODE(1) | \
|
|
EBC0_BNAP_WBN_ENCODE(1) | \
|
|
EBC0_BNAP_WBF_ENCODE(3) | \
|
|
EBC0_BNAP_TH_ENCODE(1) | \
|
|
EBC0_BNAP_RE_ENABLED | \
|
|
EBC0_BNAP_SOR_DELAYED | \
|
|
EBC0_BNAP_BEM_WRITEONLY | \
|
|
EBC0_BNAP_PEN_DISABLED
|
|
|
|
#define EBC0_BNCR_SMALL_FLASH_CS0 \
|
|
EBC0_BNCR_BAS_ENCODE(0xFFF00000) | \
|
|
EBC0_BNCR_BS_1MB | \
|
|
EBC0_BNCR_BU_RW | \
|
|
EBC0_BNCR_BW_8BIT
|
|
|
|
#define EBC0_BNCR_SMALL_FLASH_CS4 \
|
|
EBC0_BNCR_BAS_ENCODE(0x87F00000) | \
|
|
EBC0_BNCR_BS_1MB | \
|
|
EBC0_BNCR_BU_RW | \
|
|
EBC0_BNCR_BW_8BIT
|
|
|
|
/* Large Flash or SRAM */
|
|
#define EBC0_BNAP_LARGE_FLASH_OR_SRAM \
|
|
EBC0_BNAP_BME_DISABLED | \
|
|
EBC0_BNAP_TWT_ENCODE(8) | \
|
|
EBC0_BNAP_CSN_ENCODE(0) | \
|
|
EBC0_BNAP_OEN_ENCODE(1) | \
|
|
EBC0_BNAP_WBN_ENCODE(1) | \
|
|
EBC0_BNAP_WBF_ENCODE(1) | \
|
|
EBC0_BNAP_TH_ENCODE(2) | \
|
|
EBC0_BNAP_SOR_DELAYED | \
|
|
EBC0_BNAP_BEM_RW | \
|
|
EBC0_BNAP_PEN_DISABLED
|
|
|
|
#define EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS0 \
|
|
EBC0_BNCR_BAS_ENCODE(0xFF800000) | \
|
|
EBC0_BNCR_BS_8MB | \
|
|
EBC0_BNCR_BU_RW | \
|
|
EBC0_BNCR_BW_16BIT
|
|
|
|
|
|
#define EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS4 \
|
|
EBC0_BNCR_BAS_ENCODE(0x87800000) | \
|
|
EBC0_BNCR_BS_8MB | \
|
|
EBC0_BNCR_BU_RW | \
|
|
EBC0_BNCR_BW_16BIT
|
|
|
|
/* NVRAM - FPGA */
|
|
#define EBC0_BNAP_NVRAM_FPGA \
|
|
EBC0_BNAP_BME_DISABLED | \
|
|
EBC0_BNAP_TWT_ENCODE(9) | \
|
|
EBC0_BNAP_CSN_ENCODE(0) | \
|
|
EBC0_BNAP_OEN_ENCODE(1) | \
|
|
EBC0_BNAP_WBN_ENCODE(1) | \
|
|
EBC0_BNAP_WBF_ENCODE(0) | \
|
|
EBC0_BNAP_TH_ENCODE(2) | \
|
|
EBC0_BNAP_RE_ENABLED | \
|
|
EBC0_BNAP_SOR_DELAYED | \
|
|
EBC0_BNAP_BEM_WRITEONLY | \
|
|
EBC0_BNAP_PEN_DISABLED
|
|
|
|
#define EBC0_BNCR_NVRAM_FPGA_CS5 \
|
|
EBC0_BNCR_BAS_ENCODE(0x80000000) | \
|
|
EBC0_BNCR_BS_1MB | \
|
|
EBC0_BNCR_BU_RW | \
|
|
EBC0_BNCR_BW_8BIT
|
|
|
|
/* Nand Flash */
|
|
#define EBC0_BNAP_NAND_FLASH \
|
|
EBC0_BNAP_BME_DISABLED | \
|
|
EBC0_BNAP_TWT_ENCODE(3) | \
|
|
EBC0_BNAP_CSN_ENCODE(0) | \
|
|
EBC0_BNAP_OEN_ENCODE(0) | \
|
|
EBC0_BNAP_WBN_ENCODE(0) | \
|
|
EBC0_BNAP_WBF_ENCODE(0) | \
|
|
EBC0_BNAP_TH_ENCODE(1) | \
|
|
EBC0_BNAP_RE_ENABLED | \
|
|
EBC0_BNAP_SOR_NOT_DELAYED | \
|
|
EBC0_BNAP_BEM_RW | \
|
|
EBC0_BNAP_PEN_DISABLED
|
|
|
|
|
|
#define EBC0_BNCR_NAND_FLASH_CS0 0xB8400000
|
|
|
|
/* NAND0 */
|
|
#define EBC0_BNCR_NAND_FLASH_CS1 \
|
|
EBC0_BNCR_BAS_ENCODE(0x90000000) | \
|
|
EBC0_BNCR_BS_1MB | \
|
|
EBC0_BNCR_BU_RW | \
|
|
EBC0_BNCR_BW_32BIT
|
|
/* NAND1 - Bank2 */
|
|
#define EBC0_BNCR_NAND_FLASH_CS2 \
|
|
EBC0_BNCR_BAS_ENCODE(0x94000000) | \
|
|
EBC0_BNCR_BS_1MB | \
|
|
EBC0_BNCR_BU_RW | \
|
|
EBC0_BNCR_BW_32BIT
|
|
|
|
/* NAND1 - Bank3 */
|
|
#define EBC0_BNCR_NAND_FLASH_CS3 \
|
|
EBC0_BNCR_BAS_ENCODE(0x94000000) | \
|
|
EBC0_BNCR_BS_1MB | \
|
|
EBC0_BNCR_BU_RW | \
|
|
EBC0_BNCR_BW_32BIT
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
ext_bus_cntlr_init();
|
|
|
|
/*--------------------------------------------------------------------
|
|
* Setup the interrupt controller polarities, triggers, etc.
|
|
*-------------------------------------------------------------------*/
|
|
mtdcr(UIC0SR, 0xffffffff); /* clear all */
|
|
mtdcr(UIC0ER, 0x00000000); /* disable all */
|
|
mtdcr(UIC0CR, 0x00000009); /* ATI & UIC1 crit are critical */
|
|
mtdcr(UIC0PR, 0xfffffe13); /* per ref-board manual */
|
|
mtdcr(UIC0TR, 0x01c00008); /* per ref-board manual */
|
|
mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */
|
|
mtdcr(UIC0SR, 0xffffffff); /* clear all */
|
|
|
|
mtdcr(UIC1SR, 0xffffffff); /* clear all */
|
|
mtdcr(UIC1ER, 0x00000000); /* disable all */
|
|
mtdcr(UIC1CR, 0x00000000); /* all non-critical */
|
|
mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */
|
|
mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */
|
|
mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
|
|
mtdcr(UIC1SR, 0xffffffff); /* clear all */
|
|
|
|
/*--------------------------------------------------------------------
|
|
* Setup the GPIO pins
|
|
*-------------------------------------------------------------------*/
|
|
out32(GPIO0_OSRL, 0x00000400);
|
|
out32(GPIO0_OSRH, 0x00000000);
|
|
out32(GPIO0_TSRL, 0x00000400);
|
|
out32(GPIO0_TSRH, 0x00000000);
|
|
out32(GPIO0_ISR1L, 0x00000000);
|
|
out32(GPIO0_ISR1H, 0x00000000);
|
|
out32(GPIO0_ISR2L, 0x00000000);
|
|
out32(GPIO0_ISR2H, 0x00000000);
|
|
out32(GPIO0_ISR3L, 0x00000000);
|
|
out32(GPIO0_ISR3H, 0x00000000);
|
|
|
|
out32(GPIO1_OSRL, 0x0C380000);
|
|
out32(GPIO1_OSRH, 0x00000000);
|
|
out32(GPIO1_TSRL, 0x0C380000);
|
|
out32(GPIO1_TSRH, 0x00000000);
|
|
out32(GPIO1_ISR1L, 0x0FC30000);
|
|
out32(GPIO1_ISR1H, 0x00000000);
|
|
out32(GPIO1_ISR2L, 0x0C010000);
|
|
out32(GPIO1_ISR2H, 0x00000000);
|
|
out32(GPIO1_ISR3L, 0x01400000);
|
|
out32(GPIO1_ISR3H, 0x00000000);
|
|
|
|
configure_ppc440ep_pins();
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
char buf[64];
|
|
int i = getenv_f("serial#", buf, sizeof(buf));
|
|
|
|
printf("Board: Bamboo - AMCC PPC440EP Evaluation Board");
|
|
if (i > 0) {
|
|
puts(", serial# ");
|
|
puts(buf);
|
|
}
|
|
putc('\n');
|
|
|
|
return (0);
|
|
}
|
|
|
|
|
|
phys_size_t initdram (int board_type)
|
|
{
|
|
#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL))
|
|
long dram_size;
|
|
|
|
dram_size = spd_sdram();
|
|
|
|
return dram_size;
|
|
#else
|
|
return CONFIG_SYS_MBYTES_SDRAM << 20;
|
|
#endif
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| is_powerpc440ep_pass1.
|
|
+----------------------------------------------------------------------------*/
|
|
int is_powerpc440ep_pass1(void)
|
|
{
|
|
unsigned long pvr;
|
|
|
|
pvr = get_pvr();
|
|
|
|
if (pvr == PVR_POWERPC_440EP_PASS1)
|
|
return true;
|
|
else if (pvr == PVR_POWERPC_440EP_PASS2)
|
|
return false;
|
|
else {
|
|
printf("brdutil error 3\n");
|
|
for (;;)
|
|
;
|
|
}
|
|
|
|
return false;
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| is_nand_selected.
|
|
+----------------------------------------------------------------------------*/
|
|
int is_nand_selected(void)
|
|
{
|
|
#ifdef CONFIG_BAMBOO_NAND
|
|
return true;
|
|
#else
|
|
return false;
|
|
#endif
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| config_on_ebc_cs4_is_small_flash => from EPLD
|
|
+----------------------------------------------------------------------------*/
|
|
unsigned char config_on_ebc_cs4_is_small_flash(void)
|
|
{
|
|
/* Not implemented yet => returns constant value */
|
|
return true;
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| Ext_bus_cntlr_init.
|
|
| Initialize the external bus controller
|
|
+----------------------------------------------------------------------------*/
|
|
void ext_bus_cntlr_init(void)
|
|
{
|
|
unsigned long sdr0_pstrp0, sdr0_sdstp1;
|
|
unsigned long bootstrap_settings, boot_selection, ebc_boot_size;
|
|
int computed_boot_device = BOOT_DEVICE_UNKNOWN;
|
|
unsigned long ebc0_cs0_bnap_value = 0, ebc0_cs0_bncr_value = 0;
|
|
unsigned long ebc0_cs1_bnap_value = 0, ebc0_cs1_bncr_value = 0;
|
|
unsigned long ebc0_cs2_bnap_value = 0, ebc0_cs2_bncr_value = 0;
|
|
unsigned long ebc0_cs3_bnap_value = 0, ebc0_cs3_bncr_value = 0;
|
|
unsigned long ebc0_cs4_bnap_value = 0, ebc0_cs4_bncr_value = 0;
|
|
|
|
|
|
/*-------------------------------------------------------------------------+
|
|
|
|
|
| PART 1 : Initialize EBC Bank 5
|
|
| ==============================
|
|
| Bank5 is always associated to the NVRAM/EPLD.
|
|
| It has to be initialized prior to other banks settings computation since
|
|
| some board registers values may be needed
|
|
|
|
|
+-------------------------------------------------------------------------*/
|
|
/* NVRAM - FPGA */
|
|
mtebc(PB5AP, EBC0_BNAP_NVRAM_FPGA);
|
|
mtebc(PB5CR, EBC0_BNCR_NVRAM_FPGA_CS5);
|
|
|
|
/*-------------------------------------------------------------------------+
|
|
|
|
|
| PART 2 : Determine which boot device was selected
|
|
| =========================================
|
|
|
|
|
| Read Pin Strap Register in PPC440EP
|
|
| In case of boot from IIC, read Serial Device Strap Register1
|
|
|
|
|
| Result can either be :
|
|
| - Boot from EBC 8bits => SMALL FLASH
|
|
| - Boot from EBC 16bits => Large Flash or SRAM
|
|
| - Boot from NAND Flash
|
|
| - Boot from PCI
|
|
|
|
|
+-------------------------------------------------------------------------*/
|
|
/* Read Pin Strap Register in PPC440EP */
|
|
mfsdr(SDR0_PINSTP, sdr0_pstrp0);
|
|
bootstrap_settings = sdr0_pstrp0 & SDR0_PSTRP0_BOOTSTRAP_MASK;
|
|
|
|
/*-------------------------------------------------------------------------+
|
|
| PPC440EP Pass1
|
|
+-------------------------------------------------------------------------*/
|
|
if (is_powerpc440ep_pass1() == true) {
|
|
switch(bootstrap_settings) {
|
|
case SDR0_PSTRP0_BOOTSTRAP_SETTINGS0:
|
|
/* Default Strap Settings 0 : CPU 400 - PLB 133 - Boot EBC 8 bit 33MHz */
|
|
/* Boot from Small Flash */
|
|
computed_boot_device = BOOT_FROM_SMALL_FLASH;
|
|
break;
|
|
case SDR0_PSTRP0_BOOTSTRAP_SETTINGS1:
|
|
/* Default Strap Settings 1 : CPU 533 - PLB 133 - Boot PCI 66MHz */
|
|
/* Boot from PCI */
|
|
computed_boot_device = BOOT_FROM_PCI;
|
|
break;
|
|
|
|
case SDR0_PSTRP0_BOOTSTRAP_SETTINGS2:
|
|
/* Default Strap Settings 2 : CPU 500 - PLB 100 - Boot NDFC16 66MHz */
|
|
/* Boot from Nand Flash */
|
|
computed_boot_device = BOOT_FROM_NAND_FLASH0;
|
|
break;
|
|
|
|
case SDR0_PSTRP0_BOOTSTRAP_SETTINGS3:
|
|
/* Default Strap Settings 3 : CPU 333 - PLB 133 - Boot EBC 8 bit 66MHz */
|
|
/* Boot from Small Flash */
|
|
computed_boot_device = BOOT_FROM_SMALL_FLASH;
|
|
break;
|
|
|
|
case SDR0_PSTRP0_BOOTSTRAP_IIC_A8_EN:
|
|
case SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN:
|
|
/* Boot Settings in IIC EEprom address 0xA8 or 0xA4 */
|
|
/* Read Serial Device Strap Register1 in PPC440EP */
|
|
mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
|
|
boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_BOOT_SEL_MASK;
|
|
ebc_boot_size = sdr0_sdstp1 & SDR0_SDSTP1_EBC_ROM_BS_MASK;
|
|
|
|
switch(boot_selection) {
|
|
case SDR0_SDSTP1_BOOT_SEL_EBC:
|
|
switch(ebc_boot_size) {
|
|
case SDR0_SDSTP1_EBC_ROM_BS_16BIT:
|
|
computed_boot_device = BOOT_FROM_LARGE_FLASH_OR_SRAM;
|
|
break;
|
|
case SDR0_SDSTP1_EBC_ROM_BS_8BIT:
|
|
computed_boot_device = BOOT_FROM_SMALL_FLASH;
|
|
break;
|
|
}
|
|
break;
|
|
|
|
case SDR0_SDSTP1_BOOT_SEL_PCI:
|
|
computed_boot_device = BOOT_FROM_PCI;
|
|
break;
|
|
|
|
case SDR0_SDSTP1_BOOT_SEL_NDFC:
|
|
computed_boot_device = BOOT_FROM_NAND_FLASH0;
|
|
break;
|
|
}
|
|
break;
|
|
}
|
|
}
|
|
|
|
/*-------------------------------------------------------------------------+
|
|
| PPC440EP Pass2
|
|
+-------------------------------------------------------------------------*/
|
|
else {
|
|
switch(bootstrap_settings) {
|
|
case SDR0_PSTRP0_BOOTSTRAP_SETTINGS0:
|
|
/* Default Strap Settings 0 : CPU 400 - PLB 133 - Boot EBC 8 bit 33MHz */
|
|
/* Boot from Small Flash */
|
|
computed_boot_device = BOOT_FROM_SMALL_FLASH;
|
|
break;
|
|
case SDR0_PSTRP0_BOOTSTRAP_SETTINGS1:
|
|
/* Default Strap Settings 1 : CPU 333 - PLB 133 - Boot PCI 66MHz */
|
|
/* Boot from PCI */
|
|
computed_boot_device = BOOT_FROM_PCI;
|
|
break;
|
|
|
|
case SDR0_PSTRP0_BOOTSTRAP_SETTINGS2:
|
|
/* Default Strap Settings 2 : CPU 400 - PLB 100 - Boot NDFC16 33MHz */
|
|
/* Boot from Nand Flash */
|
|
computed_boot_device = BOOT_FROM_NAND_FLASH0;
|
|
break;
|
|
|
|
case SDR0_PSTRP0_BOOTSTRAP_SETTINGS3:
|
|
/* Default Strap Settings 3 : CPU 400 - PLB 100 - Boot EBC 16 bit 33MHz */
|
|
/* Boot from Large Flash or SRAM */
|
|
computed_boot_device = BOOT_FROM_LARGE_FLASH_OR_SRAM;
|
|
break;
|
|
|
|
case SDR0_PSTRP0_BOOTSTRAP_SETTINGS4:
|
|
/* Default Strap Settings 4 : CPU 333 - PLB 133 - Boot EBC 16 bit 66MHz */
|
|
/* Boot from Large Flash or SRAM */
|
|
computed_boot_device = BOOT_FROM_LARGE_FLASH_OR_SRAM;
|
|
break;
|
|
|
|
case SDR0_PSTRP0_BOOTSTRAP_SETTINGS6:
|
|
/* Default Strap Settings 6 : CPU 400 - PLB 100 - Boot PCI 33MHz */
|
|
/* Boot from PCI */
|
|
computed_boot_device = BOOT_FROM_PCI;
|
|
break;
|
|
|
|
case SDR0_PSTRP0_BOOTSTRAP_IIC_A8_EN:
|
|
case SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN:
|
|
/* Default Strap Settings 5-7 */
|
|
/* Boot Settings in IIC EEprom address 0xA8 or 0xA4 */
|
|
/* Read Serial Device Strap Register1 in PPC440EP */
|
|
mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
|
|
boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_BOOT_SEL_MASK;
|
|
ebc_boot_size = sdr0_sdstp1 & SDR0_SDSTP1_EBC_ROM_BS_MASK;
|
|
|
|
switch(boot_selection) {
|
|
case SDR0_SDSTP1_BOOT_SEL_EBC:
|
|
switch(ebc_boot_size) {
|
|
case SDR0_SDSTP1_EBC_ROM_BS_16BIT:
|
|
computed_boot_device = BOOT_FROM_LARGE_FLASH_OR_SRAM;
|
|
break;
|
|
case SDR0_SDSTP1_EBC_ROM_BS_8BIT:
|
|
computed_boot_device = BOOT_FROM_SMALL_FLASH;
|
|
break;
|
|
}
|
|
break;
|
|
|
|
case SDR0_SDSTP1_BOOT_SEL_PCI:
|
|
computed_boot_device = BOOT_FROM_PCI;
|
|
break;
|
|
|
|
case SDR0_SDSTP1_BOOT_SEL_NDFC:
|
|
computed_boot_device = BOOT_FROM_NAND_FLASH0;
|
|
break;
|
|
}
|
|
break;
|
|
}
|
|
}
|
|
|
|
/*-------------------------------------------------------------------------+
|
|
|
|
|
| PART 3 : Compute EBC settings depending on selected boot device
|
|
| ====== ======================================================
|
|
|
|
|
| Resulting EBC init will be among following configurations :
|
|
|
|
|
| - Boot from EBC 8bits => boot from SMALL FLASH selected
|
|
| EBC-CS0 = Small Flash
|
|
| EBC-CS1,2,3 = NAND Flash or
|
|
| Exp.Slot depending on Soft Config
|
|
| EBC-CS4 = SRAM/Large Flash or
|
|
| Large Flash/SRAM depending on jumpers
|
|
| EBC-CS5 = NVRAM / EPLD
|
|
|
|
|
| - Boot from EBC 16bits => boot from Large Flash or SRAM selected
|
|
| EBC-CS0 = SRAM/Large Flash or
|
|
| Large Flash/SRAM depending on jumpers
|
|
| EBC-CS1,2,3 = NAND Flash or
|
|
| Exp.Slot depending on Software Configuration
|
|
| EBC-CS4 = Small Flash
|
|
| EBC-CS5 = NVRAM / EPLD
|
|
|
|
|
| - Boot from NAND Flash
|
|
| EBC-CS0 = NAND Flash0
|
|
| EBC-CS1,2,3 = NAND Flash1
|
|
| EBC-CS4 = SRAM/Large Flash or
|
|
| Large Flash/SRAM depending on jumpers
|
|
| EBC-CS5 = NVRAM / EPLD
|
|
|
|
|
| - Boot from PCI
|
|
| EBC-CS0 = ...
|
|
| EBC-CS1,2,3 = NAND Flash or
|
|
| Exp.Slot depending on Software Configuration
|
|
| EBC-CS4 = SRAM/Large Flash or
|
|
| Large Flash/SRAM or
|
|
| Small Flash depending on jumpers
|
|
| EBC-CS5 = NVRAM / EPLD
|
|
|
|
|
+-------------------------------------------------------------------------*/
|
|
|
|
switch(computed_boot_device) {
|
|
/*------------------------------------------------------------------------- */
|
|
case BOOT_FROM_SMALL_FLASH:
|
|
/*------------------------------------------------------------------------- */
|
|
ebc0_cs0_bnap_value = EBC0_BNAP_SMALL_FLASH;
|
|
ebc0_cs0_bncr_value = EBC0_BNCR_SMALL_FLASH_CS0;
|
|
if ((is_nand_selected()) == true) {
|
|
/* NAND Flash */
|
|
ebc0_cs1_bnap_value = EBC0_BNAP_NAND_FLASH;
|
|
ebc0_cs1_bncr_value = EBC0_BNCR_NAND_FLASH_CS1;
|
|
ebc0_cs2_bnap_value = EBC0_BNAP_NAND_FLASH;
|
|
ebc0_cs2_bncr_value = EBC0_BNCR_NAND_FLASH_CS2;
|
|
ebc0_cs3_bnap_value = 0;
|
|
ebc0_cs3_bncr_value = 0;
|
|
} else {
|
|
/* Expansion Slot */
|
|
ebc0_cs1_bnap_value = 0;
|
|
ebc0_cs1_bncr_value = 0;
|
|
ebc0_cs2_bnap_value = 0;
|
|
ebc0_cs2_bncr_value = 0;
|
|
ebc0_cs3_bnap_value = 0;
|
|
ebc0_cs3_bncr_value = 0;
|
|
}
|
|
ebc0_cs4_bnap_value = EBC0_BNAP_LARGE_FLASH_OR_SRAM;
|
|
ebc0_cs4_bncr_value = EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS4;
|
|
|
|
break;
|
|
|
|
/*------------------------------------------------------------------------- */
|
|
case BOOT_FROM_LARGE_FLASH_OR_SRAM:
|
|
/*------------------------------------------------------------------------- */
|
|
ebc0_cs0_bnap_value = EBC0_BNAP_LARGE_FLASH_OR_SRAM;
|
|
ebc0_cs0_bncr_value = EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS0;
|
|
if ((is_nand_selected()) == true) {
|
|
/* NAND Flash */
|
|
ebc0_cs1_bnap_value = EBC0_BNAP_NAND_FLASH;
|
|
ebc0_cs1_bncr_value = EBC0_BNCR_NAND_FLASH_CS1;
|
|
ebc0_cs2_bnap_value = 0;
|
|
ebc0_cs2_bncr_value = 0;
|
|
ebc0_cs3_bnap_value = 0;
|
|
ebc0_cs3_bncr_value = 0;
|
|
} else {
|
|
/* Expansion Slot */
|
|
ebc0_cs1_bnap_value = 0;
|
|
ebc0_cs1_bncr_value = 0;
|
|
ebc0_cs2_bnap_value = 0;
|
|
ebc0_cs2_bncr_value = 0;
|
|
ebc0_cs3_bnap_value = 0;
|
|
ebc0_cs3_bncr_value = 0;
|
|
}
|
|
ebc0_cs4_bnap_value = EBC0_BNAP_SMALL_FLASH;
|
|
ebc0_cs4_bncr_value = EBC0_BNCR_SMALL_FLASH_CS4;
|
|
|
|
break;
|
|
|
|
/*------------------------------------------------------------------------- */
|
|
case BOOT_FROM_NAND_FLASH0:
|
|
/*------------------------------------------------------------------------- */
|
|
ebc0_cs0_bnap_value = EBC0_BNAP_NAND_FLASH;
|
|
ebc0_cs0_bncr_value = EBC0_BNCR_NAND_FLASH_CS1;
|
|
|
|
ebc0_cs1_bnap_value = 0;
|
|
ebc0_cs1_bncr_value = 0;
|
|
ebc0_cs2_bnap_value = 0;
|
|
ebc0_cs2_bncr_value = 0;
|
|
ebc0_cs3_bnap_value = 0;
|
|
ebc0_cs3_bncr_value = 0;
|
|
|
|
/* Large Flash or SRAM */
|
|
ebc0_cs4_bnap_value = EBC0_BNAP_LARGE_FLASH_OR_SRAM;
|
|
ebc0_cs4_bncr_value = EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS4;
|
|
|
|
break;
|
|
|
|
/*------------------------------------------------------------------------- */
|
|
case BOOT_FROM_PCI:
|
|
/*------------------------------------------------------------------------- */
|
|
ebc0_cs0_bnap_value = 0;
|
|
ebc0_cs0_bncr_value = 0;
|
|
|
|
if ((is_nand_selected()) == true) {
|
|
/* NAND Flash */
|
|
ebc0_cs1_bnap_value = EBC0_BNAP_NAND_FLASH;
|
|
ebc0_cs1_bncr_value = EBC0_BNCR_NAND_FLASH_CS1;
|
|
ebc0_cs2_bnap_value = 0;
|
|
ebc0_cs2_bncr_value = 0;
|
|
ebc0_cs3_bnap_value = 0;
|
|
ebc0_cs3_bncr_value = 0;
|
|
} else {
|
|
/* Expansion Slot */
|
|
ebc0_cs1_bnap_value = 0;
|
|
ebc0_cs1_bncr_value = 0;
|
|
ebc0_cs2_bnap_value = 0;
|
|
ebc0_cs2_bncr_value = 0;
|
|
ebc0_cs3_bnap_value = 0;
|
|
ebc0_cs3_bncr_value = 0;
|
|
}
|
|
|
|
if ((config_on_ebc_cs4_is_small_flash()) == true) {
|
|
/* Small Flash */
|
|
ebc0_cs4_bnap_value = EBC0_BNAP_SMALL_FLASH;
|
|
ebc0_cs4_bncr_value = EBC0_BNCR_SMALL_FLASH_CS4;
|
|
} else {
|
|
/* Large Flash or SRAM */
|
|
ebc0_cs4_bnap_value = EBC0_BNAP_LARGE_FLASH_OR_SRAM;
|
|
ebc0_cs4_bncr_value = EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS4;
|
|
}
|
|
|
|
break;
|
|
|
|
/*------------------------------------------------------------------------- */
|
|
case BOOT_DEVICE_UNKNOWN:
|
|
/*------------------------------------------------------------------------- */
|
|
/* Error */
|
|
break;
|
|
|
|
}
|
|
|
|
|
|
/*-------------------------------------------------------------------------+
|
|
| Initialize EBC CONFIG
|
|
+-------------------------------------------------------------------------*/
|
|
mtdcr(EBC0_CFGADDR, EBC0_CFG);
|
|
mtdcr(EBC0_CFGDATA, EBC0_CFG_EBTC_DRIVEN |
|
|
EBC0_CFG_PTD_ENABLED |
|
|
EBC0_CFG_RTC_2048PERCLK |
|
|
EBC0_CFG_EMPL_LOW |
|
|
EBC0_CFG_EMPH_LOW |
|
|
EBC0_CFG_CSTC_DRIVEN |
|
|
EBC0_CFG_BPF_ONEDW |
|
|
EBC0_CFG_EMS_8BIT |
|
|
EBC0_CFG_PME_DISABLED |
|
|
EBC0_CFG_PMT_ENCODE(0) );
|
|
|
|
/*-------------------------------------------------------------------------+
|
|
| Initialize EBC Bank 0-4
|
|
+-------------------------------------------------------------------------*/
|
|
/* EBC Bank0 */
|
|
mtebc(PB0AP, ebc0_cs0_bnap_value);
|
|
mtebc(PB0CR, ebc0_cs0_bncr_value);
|
|
/* EBC Bank1 */
|
|
mtebc(PB1AP, ebc0_cs1_bnap_value);
|
|
mtebc(PB1CR, ebc0_cs1_bncr_value);
|
|
/* EBC Bank2 */
|
|
mtebc(PB2AP, ebc0_cs2_bnap_value);
|
|
mtebc(PB2CR, ebc0_cs2_bncr_value);
|
|
/* EBC Bank3 */
|
|
mtebc(PB3AP, ebc0_cs3_bnap_value);
|
|
mtebc(PB3CR, ebc0_cs3_bncr_value);
|
|
/* EBC Bank4 */
|
|
mtebc(PB4AP, ebc0_cs4_bnap_value);
|
|
mtebc(PB4CR, ebc0_cs4_bncr_value);
|
|
|
|
return;
|
|
}
|
|
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| get_uart_configuration.
|
|
+----------------------------------------------------------------------------*/
|
|
uart_config_nb_t get_uart_configuration(void)
|
|
{
|
|
return (L4);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| set_phy_configuration_through_fpga => to EPLD
|
|
+----------------------------------------------------------------------------*/
|
|
void set_phy_configuration_through_fpga(zmii_config_t config)
|
|
{
|
|
|
|
unsigned long fpga_selection_reg;
|
|
|
|
fpga_selection_reg = in8(FPGA_SELECTION_1_REG) & ~FPGA_SEL_1_REG_PHY_MASK;
|
|
|
|
switch(config)
|
|
{
|
|
case ZMII_CONFIGURATION_IS_MII:
|
|
fpga_selection_reg = fpga_selection_reg | FPGA_SEL_1_REG_MII;
|
|
break;
|
|
case ZMII_CONFIGURATION_IS_RMII:
|
|
fpga_selection_reg = fpga_selection_reg | FPGA_SEL_1_REG_RMII;
|
|
break;
|
|
case ZMII_CONFIGURATION_IS_SMII:
|
|
fpga_selection_reg = fpga_selection_reg | FPGA_SEL_1_REG_SMII;
|
|
break;
|
|
case ZMII_CONFIGURATION_UNKNOWN:
|
|
default:
|
|
break;
|
|
}
|
|
out8(FPGA_SELECTION_1_REG,fpga_selection_reg);
|
|
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| scp_selection_in_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void scp_selection_in_fpga(void)
|
|
{
|
|
unsigned long fpga_selection_2_reg;
|
|
|
|
fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) & ~FPGA_SEL2_REG_IIC1_SCP_SEL_MASK;
|
|
fpga_selection_2_reg |= FPGA_SEL2_REG_SEL_SCP;
|
|
out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| iic1_selection_in_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void iic1_selection_in_fpga(void)
|
|
{
|
|
unsigned long fpga_selection_2_reg;
|
|
|
|
fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) & ~FPGA_SEL2_REG_IIC1_SCP_SEL_MASK;
|
|
fpga_selection_2_reg |= FPGA_SEL2_REG_SEL_IIC1;
|
|
out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| dma_a_b_selection_in_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void dma_a_b_selection_in_fpga(void)
|
|
{
|
|
unsigned long fpga_selection_2_reg;
|
|
|
|
fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) | FPGA_SEL2_REG_SEL_DMA_A_B;
|
|
out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| dma_a_b_unselect_in_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void dma_a_b_unselect_in_fpga(void)
|
|
{
|
|
unsigned long fpga_selection_2_reg;
|
|
|
|
fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) & ~FPGA_SEL2_REG_SEL_DMA_A_B;
|
|
out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| dma_c_d_selection_in_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void dma_c_d_selection_in_fpga(void)
|
|
{
|
|
unsigned long fpga_selection_2_reg;
|
|
|
|
fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) | FPGA_SEL2_REG_SEL_DMA_C_D;
|
|
out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| dma_c_d_unselect_in_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void dma_c_d_unselect_in_fpga(void)
|
|
{
|
|
unsigned long fpga_selection_2_reg;
|
|
|
|
fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) & ~FPGA_SEL2_REG_SEL_DMA_C_D;
|
|
out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| usb2_device_selection_in_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void usb2_device_selection_in_fpga(void)
|
|
{
|
|
unsigned long fpga_selection_1_reg;
|
|
|
|
fpga_selection_1_reg = in8(FPGA_SELECTION_1_REG) | FPGA_SEL_1_REG_USB2_DEV_SEL;
|
|
out8(FPGA_SELECTION_1_REG,fpga_selection_1_reg);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| usb2_device_reset_through_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void usb2_device_reset_through_fpga(void)
|
|
{
|
|
/* Perform soft Reset pulse */
|
|
unsigned long fpga_reset_reg;
|
|
int i;
|
|
|
|
fpga_reset_reg = in8(FPGA_RESET_REG);
|
|
out8(FPGA_RESET_REG,fpga_reset_reg | FPGA_RESET_REG_RESET_USB20_DEV);
|
|
for (i=0; i<500; i++)
|
|
udelay(1000);
|
|
out8(FPGA_RESET_REG,fpga_reset_reg);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| usb2_host_selection_in_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void usb2_host_selection_in_fpga(void)
|
|
{
|
|
unsigned long fpga_selection_1_reg;
|
|
|
|
fpga_selection_1_reg = in8(FPGA_SELECTION_1_REG) | FPGA_SEL_1_REG_USB2_HOST_SEL;
|
|
out8(FPGA_SELECTION_1_REG,fpga_selection_1_reg);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| ndfc_selection_in_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void ndfc_selection_in_fpga(void)
|
|
{
|
|
unsigned long fpga_selection_1_reg;
|
|
|
|
fpga_selection_1_reg = in8(FPGA_SELECTION_1_REG) &~FPGA_SEL_1_REG_NF_SELEC_MASK;
|
|
fpga_selection_1_reg |= FPGA_SEL_1_REG_NF0_SEL_BY_NFCS1;
|
|
fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS2;
|
|
out8(FPGA_SELECTION_1_REG,fpga_selection_1_reg);
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| uart_selection_in_fpga.
|
|
+----------------------------------------------------------------------------*/
|
|
void uart_selection_in_fpga(uart_config_nb_t uart_config)
|
|
{
|
|
/* FPGA register */
|
|
unsigned char fpga_selection_3_reg;
|
|
|
|
/* Read FPGA Reagister */
|
|
fpga_selection_3_reg = in8(FPGA_SELECTION_3_REG);
|
|
|
|
switch (uart_config)
|
|
{
|
|
case L1:
|
|
/* ----------------------------------------------------------------------- */
|
|
/* L1 configuration: UART0 = 8 pins */
|
|
/* ----------------------------------------------------------------------- */
|
|
/* Configure FPGA */
|
|
fpga_selection_3_reg = fpga_selection_3_reg & ~FPGA_SEL3_REG_SEL_UART_CONFIG_MASK;
|
|
fpga_selection_3_reg = fpga_selection_3_reg | FPGA_SEL3_REG_SEL_UART_CONFIG1;
|
|
out8(FPGA_SELECTION_3_REG, fpga_selection_3_reg);
|
|
|
|
break;
|
|
|
|
case L2:
|
|
/* ----------------------------------------------------------------------- */
|
|
/* L2 configuration: UART0 = 4 pins */
|
|
/* UART1 = 4 pins */
|
|
/* ----------------------------------------------------------------------- */
|
|
/* Configure FPGA */
|
|
fpga_selection_3_reg = fpga_selection_3_reg & ~FPGA_SEL3_REG_SEL_UART_CONFIG_MASK;
|
|
fpga_selection_3_reg = fpga_selection_3_reg | FPGA_SEL3_REG_SEL_UART_CONFIG2;
|
|
out8(FPGA_SELECTION_3_REG, fpga_selection_3_reg);
|
|
|
|
break;
|
|
|
|
case L3:
|
|
/* ----------------------------------------------------------------------- */
|
|
/* L3 configuration: UART0 = 4 pins */
|
|
/* UART1 = 2 pins */
|
|
/* UART2 = 2 pins */
|
|
/* ----------------------------------------------------------------------- */
|
|
/* Configure FPGA */
|
|
fpga_selection_3_reg = fpga_selection_3_reg & ~FPGA_SEL3_REG_SEL_UART_CONFIG_MASK;
|
|
fpga_selection_3_reg = fpga_selection_3_reg | FPGA_SEL3_REG_SEL_UART_CONFIG3;
|
|
out8(FPGA_SELECTION_3_REG, fpga_selection_3_reg);
|
|
break;
|
|
|
|
case L4:
|
|
/* Configure FPGA */
|
|
fpga_selection_3_reg = fpga_selection_3_reg & ~FPGA_SEL3_REG_SEL_UART_CONFIG_MASK;
|
|
fpga_selection_3_reg = fpga_selection_3_reg | FPGA_SEL3_REG_SEL_UART_CONFIG4;
|
|
out8(FPGA_SELECTION_3_REG, fpga_selection_3_reg);
|
|
|
|
break;
|
|
|
|
default:
|
|
/* Unsupported UART configuration number */
|
|
for (;;)
|
|
;
|
|
break;
|
|
|
|
}
|
|
}
|
|
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| init_default_gpio
|
|
+----------------------------------------------------------------------------*/
|
|
void init_default_gpio(gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
int i;
|
|
|
|
/* Init GPIO0 */
|
|
for(i=0; i<GPIO_MAX; i++)
|
|
{
|
|
gpio_tab[GPIO0][i].add = GPIO0_BASE;
|
|
gpio_tab[GPIO0][i].in_out = GPIO_DIS;
|
|
gpio_tab[GPIO0][i].alt_nb = GPIO_SEL;
|
|
}
|
|
|
|
/* Init GPIO1 */
|
|
for(i=0; i<GPIO_MAX; i++)
|
|
{
|
|
gpio_tab[GPIO1][i].add = GPIO1_BASE;
|
|
gpio_tab[GPIO1][i].in_out = GPIO_DIS;
|
|
gpio_tab[GPIO1][i].alt_nb = GPIO_SEL;
|
|
}
|
|
|
|
/* EBC_CS_N(5) - GPIO0_10 */
|
|
gpio_tab[GPIO0][10].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO0][10].alt_nb = GPIO_ALT1;
|
|
|
|
/* EBC_CS_N(4) - GPIO0_9 */
|
|
gpio_tab[GPIO0][9].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO0][9].alt_nb = GPIO_ALT1;
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| update_uart_ios
|
|
+------------------------------------------------------------------------------
|
|
|
|
|
| Set UART Configuration in PowerPC440EP
|
|
|
|
|
| +---------------------------------------------------------------------+
|
|
| | Configuartion | Connector | Nb of pins | Pins | Associated |
|
|
| | Number | Port Name | available | naming | CORE |
|
|
| +-----------------+---------------+------------+--------+-------------+
|
|
| | L1 | Port_A | 8 | UART | UART core 0 |
|
|
| +-----------------+---------------+------------+--------+-------------+
|
|
| | L2 | Port_A | 4 | UART1 | UART core 0 |
|
|
| | (L2D) | Port_B | 4 | UART2 | UART core 1 |
|
|
| +-----------------+---------------+------------+--------+-------------+
|
|
| | L3 | Port_A | 4 | UART1 | UART core 0 |
|
|
| | (L3D) | Port_B | 2 | UART2 | UART core 1 |
|
|
| | | Port_C | 2 | UART3 | UART core 2 |
|
|
| +-----------------+---------------+------------+--------+-------------+
|
|
| | | Port_A | 2 | UART1 | UART core 0 |
|
|
| | L4 | Port_B | 2 | UART2 | UART core 1 |
|
|
| | (L4D) | Port_C | 2 | UART3 | UART core 2 |
|
|
| | | Port_D | 2 | UART4 | UART core 3 |
|
|
| +-----------------+---------------+------------+--------+-------------+
|
|
|
|
|
| Involved GPIOs
|
|
|
|
|
| +------------------------------------------------------------------------------+
|
|
| | GPIO | Aternate 1 | I/O | Alternate 2 | I/O | Alternate 3 | I/O |
|
|
| +---------+------------------+-----+-----------------+-----+-------------+-----+
|
|
| | GPIO1_2 | UART0_DCD_N | I | UART1_DSR_CTS_N | I | UART2_SOUT | O |
|
|
| | GPIO1_3 | UART0_8PIN_DSR_N | I | UART1_RTS_DTR_N | O | UART2_SIN | I |
|
|
| | GPIO1_4 | UART0_8PIN_CTS_N | I | NA | NA | UART3_SIN | I |
|
|
| | GPIO1_5 | UART0_RTS_N | O | NA | NA | UART3_SOUT | O |
|
|
| | GPIO1_6 | UART0_DTR_N | O | UART1_SOUT | O | NA | NA |
|
|
| | GPIO1_7 | UART0_RI_N | I | UART1_SIN | I | NA | NA |
|
|
| +------------------------------------------------------------------------------+
|
|
|
|
|
|
|
|
+----------------------------------------------------------------------------*/
|
|
|
|
void update_uart_ios(uart_config_nb_t uart_config, gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
switch (uart_config)
|
|
{
|
|
case L1:
|
|
/* ----------------------------------------------------------------------- */
|
|
/* L1 configuration: UART0 = 8 pins */
|
|
/* ----------------------------------------------------------------------- */
|
|
/* Update GPIO Configuration Table */
|
|
gpio_tab[GPIO1][2].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][2].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][3].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][3].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][4].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][4].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][5].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][5].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][6].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][6].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][7].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][7].alt_nb = GPIO_ALT1;
|
|
|
|
break;
|
|
|
|
case L2:
|
|
/* ----------------------------------------------------------------------- */
|
|
/* L2 configuration: UART0 = 4 pins */
|
|
/* UART1 = 4 pins */
|
|
/* ----------------------------------------------------------------------- */
|
|
/* Update GPIO Configuration Table */
|
|
gpio_tab[GPIO1][2].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][2].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO1][3].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][3].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO1][4].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][4].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][5].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][5].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][6].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][6].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO1][7].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][7].alt_nb = GPIO_ALT2;
|
|
|
|
break;
|
|
|
|
case L3:
|
|
/* ----------------------------------------------------------------------- */
|
|
/* L3 configuration: UART0 = 4 pins */
|
|
/* UART1 = 2 pins */
|
|
/* UART2 = 2 pins */
|
|
/* ----------------------------------------------------------------------- */
|
|
/* Update GPIO Configuration Table */
|
|
gpio_tab[GPIO1][2].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][2].alt_nb = GPIO_ALT3;
|
|
|
|
gpio_tab[GPIO1][3].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][3].alt_nb = GPIO_ALT3;
|
|
|
|
gpio_tab[GPIO1][4].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][4].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][5].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][5].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][6].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][6].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO1][7].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][7].alt_nb = GPIO_ALT2;
|
|
|
|
break;
|
|
|
|
case L4:
|
|
/* ----------------------------------------------------------------------- */
|
|
/* L4 configuration: UART0 = 2 pins */
|
|
/* UART1 = 2 pins */
|
|
/* UART2 = 2 pins */
|
|
/* UART3 = 2 pins */
|
|
/* ----------------------------------------------------------------------- */
|
|
/* Update GPIO Configuration Table */
|
|
gpio_tab[GPIO1][2].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][2].alt_nb = GPIO_ALT3;
|
|
|
|
gpio_tab[GPIO1][3].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][3].alt_nb = GPIO_ALT3;
|
|
|
|
gpio_tab[GPIO1][4].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][4].alt_nb = GPIO_ALT3;
|
|
|
|
gpio_tab[GPIO1][5].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][5].alt_nb = GPIO_ALT3;
|
|
|
|
gpio_tab[GPIO1][6].in_out = GPIO_OUT;
|
|
gpio_tab[GPIO1][6].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO1][7].in_out = GPIO_IN;
|
|
gpio_tab[GPIO1][7].alt_nb = GPIO_ALT2;
|
|
|
|
break;
|
|
|
|
default:
|
|
/* Unsupported UART configuration number */
|
|
printf("ERROR - Unsupported UART configuration number.\n\n");
|
|
for (;;)
|
|
;
|
|
break;
|
|
|
|
}
|
|
|
|
/* Set input Selection Register on Alt_Receive for UART Input Core */
|
|
out32(GPIO1_IS1L, (in32(GPIO1_IS1L) | 0x0FC30000));
|
|
out32(GPIO1_IS2L, (in32(GPIO1_IS2L) | 0x0C030000));
|
|
out32(GPIO1_IS3L, (in32(GPIO1_IS3L) | 0x03C00000));
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| update_ndfc_ios(void).
|
|
+----------------------------------------------------------------------------*/
|
|
void update_ndfc_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
/* Update GPIO Configuration Table */
|
|
gpio_tab[GPIO0][6].in_out = GPIO_OUT; /* EBC_CS_N(1) */
|
|
gpio_tab[GPIO0][6].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][7].in_out = GPIO_OUT; /* EBC_CS_N(2) */
|
|
gpio_tab[GPIO0][7].alt_nb = GPIO_ALT1;
|
|
|
|
#if 0
|
|
gpio_tab[GPIO0][7].in_out = GPIO_OUT; /* EBC_CS_N(3) */
|
|
gpio_tab[GPIO0][7].alt_nb = GPIO_ALT1;
|
|
#endif
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| update_zii_ios(void).
|
|
+----------------------------------------------------------------------------*/
|
|
void update_zii_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
/* Update GPIO Configuration Table */
|
|
gpio_tab[GPIO0][12].in_out = GPIO_IN; /* ZII_p0Rxd(0) */
|
|
gpio_tab[GPIO0][12].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][13].in_out = GPIO_IN; /* ZII_p0Rxd(1) */
|
|
gpio_tab[GPIO0][13].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][14].in_out = GPIO_IN; /* ZII_p0Rxd(2) */
|
|
gpio_tab[GPIO0][14].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][15].in_out = GPIO_IN; /* ZII_p0Rxd(3) */
|
|
gpio_tab[GPIO0][15].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][16].in_out = GPIO_OUT; /* ZII_p0Txd(0) */
|
|
gpio_tab[GPIO0][16].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][17].in_out = GPIO_OUT; /* ZII_p0Txd(1) */
|
|
gpio_tab[GPIO0][17].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][18].in_out = GPIO_OUT; /* ZII_p0Txd(2) */
|
|
gpio_tab[GPIO0][18].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][19].in_out = GPIO_OUT; /* ZII_p0Txd(3) */
|
|
gpio_tab[GPIO0][19].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][20].in_out = GPIO_IN; /* ZII_p0Rx_er */
|
|
gpio_tab[GPIO0][20].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][21].in_out = GPIO_IN; /* ZII_p0Rx_dv */
|
|
gpio_tab[GPIO0][21].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][22].in_out = GPIO_IN; /* ZII_p0Crs */
|
|
gpio_tab[GPIO0][22].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][23].in_out = GPIO_OUT; /* ZII_p0Tx_er */
|
|
gpio_tab[GPIO0][23].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][24].in_out = GPIO_OUT; /* ZII_p0Tx_en */
|
|
gpio_tab[GPIO0][24].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][25].in_out = GPIO_IN; /* ZII_p0Col */
|
|
gpio_tab[GPIO0][25].alt_nb = GPIO_ALT1;
|
|
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| update_uic_0_3_irq_ios().
|
|
+----------------------------------------------------------------------------*/
|
|
void update_uic_0_3_irq_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
gpio_tab[GPIO1][8].in_out = GPIO_IN; /* UIC_IRQ(0) */
|
|
gpio_tab[GPIO1][8].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][9].in_out = GPIO_IN; /* UIC_IRQ(1) */
|
|
gpio_tab[GPIO1][9].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][10].in_out = GPIO_IN; /* UIC_IRQ(2) */
|
|
gpio_tab[GPIO1][10].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][11].in_out = GPIO_IN; /* UIC_IRQ(3) */
|
|
gpio_tab[GPIO1][11].alt_nb = GPIO_ALT1;
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| update_uic_4_9_irq_ios().
|
|
+----------------------------------------------------------------------------*/
|
|
void update_uic_4_9_irq_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
gpio_tab[GPIO1][12].in_out = GPIO_IN; /* UIC_IRQ(4) */
|
|
gpio_tab[GPIO1][12].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][13].in_out = GPIO_IN; /* UIC_IRQ(6) */
|
|
gpio_tab[GPIO1][13].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][14].in_out = GPIO_IN; /* UIC_IRQ(7) */
|
|
gpio_tab[GPIO1][14].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][15].in_out = GPIO_IN; /* UIC_IRQ(8) */
|
|
gpio_tab[GPIO1][15].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][16].in_out = GPIO_IN; /* UIC_IRQ(9) */
|
|
gpio_tab[GPIO1][16].alt_nb = GPIO_ALT1;
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| update_dma_a_b_ios().
|
|
+----------------------------------------------------------------------------*/
|
|
void update_dma_a_b_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
gpio_tab[GPIO1][12].in_out = GPIO_OUT; /* DMA_ACK(1) */
|
|
gpio_tab[GPIO1][12].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO1][13].in_out = GPIO_BI; /* DMA_EOT/TC(1) */
|
|
gpio_tab[GPIO1][13].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO1][14].in_out = GPIO_IN; /* DMA_REQ(0) */
|
|
gpio_tab[GPIO1][14].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO1][15].in_out = GPIO_OUT; /* DMA_ACK(0) */
|
|
gpio_tab[GPIO1][15].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO1][16].in_out = GPIO_BI; /* DMA_EOT/TC(0) */
|
|
gpio_tab[GPIO1][16].alt_nb = GPIO_ALT2;
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| update_dma_c_d_ios().
|
|
+----------------------------------------------------------------------------*/
|
|
void update_dma_c_d_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
gpio_tab[GPIO0][0].in_out = GPIO_IN; /* DMA_REQ(2) */
|
|
gpio_tab[GPIO0][0].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO0][1].in_out = GPIO_OUT; /* DMA_ACK(2) */
|
|
gpio_tab[GPIO0][1].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO0][2].in_out = GPIO_BI; /* DMA_EOT/TC(2) */
|
|
gpio_tab[GPIO0][2].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO0][3].in_out = GPIO_IN; /* DMA_REQ(3) */
|
|
gpio_tab[GPIO0][3].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO0][4].in_out = GPIO_OUT; /* DMA_ACK(3) */
|
|
gpio_tab[GPIO0][4].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO0][5].in_out = GPIO_BI; /* DMA_EOT/TC(3) */
|
|
gpio_tab[GPIO0][5].alt_nb = GPIO_ALT2;
|
|
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| update_ebc_master_ios().
|
|
+----------------------------------------------------------------------------*/
|
|
void update_ebc_master_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
gpio_tab[GPIO0][27].in_out = GPIO_IN; /* EXT_EBC_REQ */
|
|
gpio_tab[GPIO0][27].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][29].in_out = GPIO_OUT; /* EBC_EXT_HDLA */
|
|
gpio_tab[GPIO0][29].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][30].in_out = GPIO_OUT; /* EBC_EXT_ACK */
|
|
gpio_tab[GPIO0][30].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO0][31].in_out = GPIO_OUT; /* EBC_EXR_BUSREQ */
|
|
gpio_tab[GPIO0][31].alt_nb = GPIO_ALT1;
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| update_usb2_device_ios().
|
|
+----------------------------------------------------------------------------*/
|
|
void update_usb2_device_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
gpio_tab[GPIO0][26].in_out = GPIO_IN; /* USB2D_RXVALID */
|
|
gpio_tab[GPIO0][26].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO0][27].in_out = GPIO_IN; /* USB2D_RXERROR */
|
|
gpio_tab[GPIO0][27].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO0][28].in_out = GPIO_OUT; /* USB2D_TXVALID */
|
|
gpio_tab[GPIO0][28].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO0][29].in_out = GPIO_OUT; /* USB2D_PAD_SUSPNDM */
|
|
gpio_tab[GPIO0][29].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO0][30].in_out = GPIO_OUT; /* USB2D_XCVRSELECT */
|
|
gpio_tab[GPIO0][30].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO0][31].in_out = GPIO_OUT; /* USB2D_TERMSELECT */
|
|
gpio_tab[GPIO0][31].alt_nb = GPIO_ALT2;
|
|
|
|
gpio_tab[GPIO1][0].in_out = GPIO_OUT; /* USB2D_OPMODE0 */
|
|
gpio_tab[GPIO1][0].alt_nb = GPIO_ALT1;
|
|
|
|
gpio_tab[GPIO1][1].in_out = GPIO_OUT; /* USB2D_OPMODE1 */
|
|
gpio_tab[GPIO1][1].alt_nb = GPIO_ALT1;
|
|
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| update_pci_patch_ios().
|
|
+----------------------------------------------------------------------------*/
|
|
void update_pci_patch_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
gpio_tab[GPIO0][29].in_out = GPIO_OUT; /* EBC_EXT_HDLA */
|
|
gpio_tab[GPIO0][29].alt_nb = GPIO_ALT1;
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| set_chip_gpio_configuration(unsigned char gpio_core,
|
|
| gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
| Put the core impacted by clock modification and sharing in reset.
|
|
| Config the select registers to resolve the sharing depending of the config.
|
|
| Configure the GPIO registers.
|
|
|
|
|
+----------------------------------------------------------------------------*/
|
|
void set_chip_gpio_configuration(unsigned char gpio_core, gpio_param_s (*gpio_tab)[GPIO_MAX])
|
|
{
|
|
unsigned char i=0, j=0, reg_offset = 0;
|
|
unsigned long gpio_reg, gpio_core_add;
|
|
|
|
/* GPIO config of the GPIOs 0 to 31 */
|
|
for (i=0; i<GPIO_MAX; i++, j++)
|
|
{
|
|
if (i == GPIO_MAX/2)
|
|
{
|
|
reg_offset = 4;
|
|
j = i-16;
|
|
}
|
|
|
|
gpio_core_add = gpio_tab[gpio_core][i].add;
|
|
|
|
if ( (gpio_tab[gpio_core][i].in_out == GPIO_IN) ||
|
|
(gpio_tab[gpio_core][i].in_out == GPIO_BI ))
|
|
{
|
|
switch (gpio_tab[gpio_core][i].alt_nb)
|
|
{
|
|
case GPIO_SEL:
|
|
break;
|
|
|
|
case GPIO_ALT1:
|
|
gpio_reg = in32(GPIO_IS1(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
|
|
gpio_reg = gpio_reg | (GPIO_IN_SEL >> (j*2));
|
|
out32(GPIO_IS1(gpio_core_add+reg_offset), gpio_reg);
|
|
break;
|
|
|
|
case GPIO_ALT2:
|
|
gpio_reg = in32(GPIO_IS2(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
|
|
gpio_reg = gpio_reg | (GPIO_IN_SEL >> (j*2));
|
|
out32(GPIO_IS2(gpio_core_add+reg_offset), gpio_reg);
|
|
break;
|
|
|
|
case GPIO_ALT3:
|
|
gpio_reg = in32(GPIO_IS3(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
|
|
gpio_reg = gpio_reg | (GPIO_IN_SEL >> (j*2));
|
|
out32(GPIO_IS3(gpio_core_add+reg_offset), gpio_reg);
|
|
break;
|
|
}
|
|
}
|
|
if ( (gpio_tab[gpio_core][i].in_out == GPIO_OUT) ||
|
|
(gpio_tab[gpio_core][i].in_out == GPIO_BI ))
|
|
{
|
|
|
|
switch (gpio_tab[gpio_core][i].alt_nb)
|
|
{
|
|
case GPIO_SEL:
|
|
break;
|
|
case GPIO_ALT1:
|
|
gpio_reg = in32(GPIO_OS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
|
|
gpio_reg = gpio_reg | (GPIO_ALT1_SEL >> (j*2));
|
|
out32(GPIO_OS(gpio_core_add+reg_offset), gpio_reg);
|
|
gpio_reg = in32(GPIO_TS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
|
|
gpio_reg = gpio_reg | (GPIO_ALT1_SEL >> (j*2));
|
|
out32(GPIO_TS(gpio_core_add+reg_offset), gpio_reg);
|
|
break;
|
|
case GPIO_ALT2:
|
|
gpio_reg = in32(GPIO_OS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
|
|
gpio_reg = gpio_reg | (GPIO_ALT2_SEL >> (j*2));
|
|
out32(GPIO_OS(gpio_core_add+reg_offset), gpio_reg);
|
|
gpio_reg = in32(GPIO_TS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
|
|
gpio_reg = gpio_reg | (GPIO_ALT2_SEL >> (j*2));
|
|
out32(GPIO_TS(gpio_core_add+reg_offset), gpio_reg);
|
|
break;
|
|
case GPIO_ALT3:
|
|
gpio_reg = in32(GPIO_OS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
|
|
gpio_reg = gpio_reg | (GPIO_ALT3_SEL >> (j*2));
|
|
out32(GPIO_OS(gpio_core_add+reg_offset), gpio_reg);
|
|
gpio_reg = in32(GPIO_TS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
|
|
gpio_reg = gpio_reg | (GPIO_ALT3_SEL >> (j*2));
|
|
out32(GPIO_TS(gpio_core_add+reg_offset), gpio_reg);
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| force_bup_core_selection.
|
|
+----------------------------------------------------------------------------*/
|
|
void force_bup_core_selection(core_selection_t *core_select_P, config_validity_t *config_val_P)
|
|
{
|
|
/* Pointer invalid */
|
|
if (core_select_P == NULL)
|
|
{
|
|
printf("Configuration invalid pointer 1\n");
|
|
for (;;)
|
|
;
|
|
}
|
|
|
|
/* L4 Selection */
|
|
*(core_select_P+UART_CORE0) = CORE_SELECTED;
|
|
*(core_select_P+UART_CORE1) = CORE_SELECTED;
|
|
*(core_select_P+UART_CORE2) = CORE_SELECTED;
|
|
*(core_select_P+UART_CORE3) = CORE_SELECTED;
|
|
|
|
/* RMII Selection */
|
|
*(core_select_P+RMII_SEL) = CORE_SELECTED;
|
|
|
|
/* External Interrupt 0-9 selection */
|
|
*(core_select_P+UIC_0_3) = CORE_SELECTED;
|
|
*(core_select_P+UIC_4_9) = CORE_SELECTED;
|
|
|
|
*(core_select_P+SCP_CORE) = CORE_SELECTED;
|
|
*(core_select_P+DMA_CHANNEL_CD) = CORE_SELECTED;
|
|
*(core_select_P+PACKET_REJ_FUNC_AVAIL) = CORE_SELECTED;
|
|
*(core_select_P+USB1_DEVICE) = CORE_SELECTED;
|
|
|
|
if (is_nand_selected()) {
|
|
*(core_select_P+NAND_FLASH) = CORE_SELECTED;
|
|
}
|
|
|
|
*config_val_P = CONFIG_IS_VALID;
|
|
|
|
}
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| configure_ppc440ep_pins.
|
|
+----------------------------------------------------------------------------*/
|
|
void configure_ppc440ep_pins(void)
|
|
{
|
|
uart_config_nb_t uart_configuration;
|
|
config_validity_t config_val = CONFIG_IS_INVALID;
|
|
|
|
/* Create Core Selection Table */
|
|
core_selection_t ppc440ep_core_selection[MAX_CORE_SELECT_NB] =
|
|
{
|
|
CORE_NOT_SELECTED, /* IIC_CORE, */
|
|
CORE_NOT_SELECTED, /* SPC_CORE, */
|
|
CORE_NOT_SELECTED, /* DMA_CHANNEL_AB, */
|
|
CORE_NOT_SELECTED, /* UIC_4_9, */
|
|
CORE_NOT_SELECTED, /* USB2_HOST, */
|
|
CORE_NOT_SELECTED, /* DMA_CHANNEL_CD, */
|
|
CORE_NOT_SELECTED, /* USB2_DEVICE, */
|
|
CORE_NOT_SELECTED, /* PACKET_REJ_FUNC_AVAIL, */
|
|
CORE_NOT_SELECTED, /* USB1_DEVICE, */
|
|
CORE_NOT_SELECTED, /* EBC_MASTER, */
|
|
CORE_NOT_SELECTED, /* NAND_FLASH, */
|
|
CORE_NOT_SELECTED, /* UART_CORE0, */
|
|
CORE_NOT_SELECTED, /* UART_CORE1, */
|
|
CORE_NOT_SELECTED, /* UART_CORE2, */
|
|
CORE_NOT_SELECTED, /* UART_CORE3, */
|
|
CORE_NOT_SELECTED, /* MII_SEL, */
|
|
CORE_NOT_SELECTED, /* RMII_SEL, */
|
|
CORE_NOT_SELECTED, /* SMII_SEL, */
|
|
CORE_NOT_SELECTED, /* PACKET_REJ_FUNC_EN */
|
|
CORE_NOT_SELECTED, /* UIC_0_3 */
|
|
CORE_NOT_SELECTED, /* USB1_HOST */
|
|
CORE_NOT_SELECTED /* PCI_PATCH */
|
|
};
|
|
|
|
gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX];
|
|
|
|
/* Table Default Initialisation + FPGA Access */
|
|
init_default_gpio(gpio_tab);
|
|
set_chip_gpio_configuration(GPIO0, gpio_tab);
|
|
set_chip_gpio_configuration(GPIO1, gpio_tab);
|
|
|
|
/* Update Table */
|
|
force_bup_core_selection(ppc440ep_core_selection, &config_val);
|
|
#if 0 /* test-only */
|
|
/* If we are running PIBS 1, force known configuration */
|
|
update_core_selection_table(ppc440ep_core_selection, &config_val);
|
|
#endif
|
|
|
|
/*----------------------------------------------------------------------------+
|
|
| SDR + ios table update + fpga initialization
|
|
+----------------------------------------------------------------------------*/
|
|
unsigned long sdr0_pfc1 = 0;
|
|
unsigned long sdr0_usb0 = 0;
|
|
unsigned long sdr0_mfr = 0;
|
|
|
|
/* PCI Always selected */
|
|
|
|
/* I2C Selection */
|
|
if (ppc440ep_core_selection[IIC_CORE] == CORE_SELECTED)
|
|
{
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_IIC1_SEL;
|
|
iic1_selection_in_fpga();
|
|
}
|
|
|
|
/* SCP Selection */
|
|
if (ppc440ep_core_selection[SCP_CORE] == CORE_SELECTED)
|
|
{
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_SCP_SEL;
|
|
scp_selection_in_fpga();
|
|
}
|
|
|
|
/* UIC 0:3 Selection */
|
|
if (ppc440ep_core_selection[UIC_0_3] == CORE_SELECTED)
|
|
{
|
|
update_uic_0_3_irq_ios(gpio_tab);
|
|
dma_a_b_unselect_in_fpga();
|
|
}
|
|
|
|
/* UIC 4:9 Selection */
|
|
if (ppc440ep_core_selection[UIC_4_9] == CORE_SELECTED)
|
|
{
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_DIS_MASK) | SDR0_PFC1_DIS_UICIRQ5_SEL;
|
|
update_uic_4_9_irq_ios(gpio_tab);
|
|
}
|
|
|
|
/* DMA AB Selection */
|
|
if (ppc440ep_core_selection[DMA_CHANNEL_AB] == CORE_SELECTED)
|
|
{
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_DIS_MASK) | SDR0_PFC1_DIS_DMAR_SEL;
|
|
update_dma_a_b_ios(gpio_tab);
|
|
dma_a_b_selection_in_fpga();
|
|
}
|
|
|
|
/* DMA CD Selection */
|
|
if (ppc440ep_core_selection[DMA_CHANNEL_CD] == CORE_SELECTED)
|
|
{
|
|
update_dma_c_d_ios(gpio_tab);
|
|
dma_c_d_selection_in_fpga();
|
|
}
|
|
|
|
/* EBC Master Selection */
|
|
if (ppc440ep_core_selection[EBC_MASTER] == CORE_SELECTED)
|
|
{
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_ERE_MASK) | SDR0_PFC1_ERE_EXTR_SEL;
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_EBCHR_SEL;
|
|
update_ebc_master_ios(gpio_tab);
|
|
}
|
|
|
|
/* PCI Patch Enable */
|
|
if (ppc440ep_core_selection[PCI_PATCH] == CORE_SELECTED)
|
|
{
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_EBCHR_SEL;
|
|
update_pci_patch_ios(gpio_tab);
|
|
}
|
|
|
|
/* USB2 Host Selection - Not Implemented in PowerPC 440EP Pass1 */
|
|
if (ppc440ep_core_selection[USB2_HOST] == CORE_SELECTED)
|
|
{
|
|
/* Not Implemented in PowerPC 440EP Pass1-Pass2 */
|
|
printf("Invalid configuration => USB2 Host selected\n");
|
|
for (;;)
|
|
;
|
|
/*usb2_host_selection_in_fpga(); */
|
|
}
|
|
|
|
/* USB2.0 Device Selection */
|
|
if (ppc440ep_core_selection[USB2_DEVICE] == CORE_SELECTED)
|
|
{
|
|
update_usb2_device_ios(gpio_tab);
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_USB2D_SEL;
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UPR_MASK) | SDR0_PFC1_UPR_DISABLE;
|
|
|
|
mfsdr(SDR0_USB0, sdr0_usb0);
|
|
sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_USB_DEVSEL_MASK;
|
|
sdr0_usb0 = sdr0_usb0 | SDR0_USB0_USB20D_DEVSEL;
|
|
mtsdr(SDR0_USB0, sdr0_usb0);
|
|
|
|
usb2_device_selection_in_fpga();
|
|
}
|
|
|
|
/* USB1.1 Device Selection */
|
|
if (ppc440ep_core_selection[USB1_DEVICE] == CORE_SELECTED)
|
|
{
|
|
mfsdr(SDR0_USB0, sdr0_usb0);
|
|
sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_USB_DEVSEL_MASK;
|
|
sdr0_usb0 = sdr0_usb0 | SDR0_USB0_USB11D_DEVSEL;
|
|
mtsdr(SDR0_USB0, sdr0_usb0);
|
|
}
|
|
|
|
/* USB1.1 Host Selection */
|
|
if (ppc440ep_core_selection[USB1_HOST] == CORE_SELECTED)
|
|
{
|
|
mfsdr(SDR0_USB0, sdr0_usb0);
|
|
sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_LEEN_MASK;
|
|
sdr0_usb0 = sdr0_usb0 | SDR0_USB0_LEEN_ENABLE;
|
|
mtsdr(SDR0_USB0, sdr0_usb0);
|
|
}
|
|
|
|
/* NAND Flash Selection */
|
|
if (ppc440ep_core_selection[NAND_FLASH] == CORE_SELECTED)
|
|
{
|
|
update_ndfc_ios(gpio_tab);
|
|
|
|
#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL))
|
|
mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL |
|
|
SDR0_CUST0_NDFC_ENABLE |
|
|
SDR0_CUST0_NDFC_BW_8_BIT |
|
|
SDR0_CUST0_NDFC_ARE_MASK |
|
|
SDR0_CUST0_CHIPSELGAT_EN1 |
|
|
SDR0_CUST0_CHIPSELGAT_EN2);
|
|
#else
|
|
mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL |
|
|
SDR0_CUST0_NDFC_ENABLE |
|
|
SDR0_CUST0_NDFC_BW_8_BIT |
|
|
SDR0_CUST0_NDFC_ARE_MASK |
|
|
SDR0_CUST0_CHIPSELGAT_EN0 |
|
|
SDR0_CUST0_CHIPSELGAT_EN2);
|
|
#endif
|
|
|
|
ndfc_selection_in_fpga();
|
|
}
|
|
else
|
|
{
|
|
/* Set Mux on EMAC */
|
|
mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_EMAC_SEL);
|
|
}
|
|
|
|
/* MII Selection */
|
|
if (ppc440ep_core_selection[MII_SEL] == CORE_SELECTED)
|
|
{
|
|
update_zii_ios(gpio_tab);
|
|
mfsdr(SDR0_MFR, sdr0_mfr);
|
|
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_MII;
|
|
mtsdr(SDR0_MFR, sdr0_mfr);
|
|
|
|
set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_MII);
|
|
}
|
|
|
|
/* RMII Selection */
|
|
if (ppc440ep_core_selection[RMII_SEL] == CORE_SELECTED)
|
|
{
|
|
update_zii_ios(gpio_tab);
|
|
mfsdr(SDR0_MFR, sdr0_mfr);
|
|
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_RMII_10M;
|
|
mtsdr(SDR0_MFR, sdr0_mfr);
|
|
|
|
set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_RMII);
|
|
}
|
|
|
|
/* SMII Selection */
|
|
if (ppc440ep_core_selection[SMII_SEL] == CORE_SELECTED)
|
|
{
|
|
update_zii_ios(gpio_tab);
|
|
mfsdr(SDR0_MFR, sdr0_mfr);
|
|
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_SMII;
|
|
mtsdr(SDR0_MFR, sdr0_mfr);
|
|
|
|
set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_SMII);
|
|
}
|
|
|
|
/* UART Selection */
|
|
uart_configuration = get_uart_configuration();
|
|
switch (uart_configuration)
|
|
{
|
|
case L1: /* L1 Selection */
|
|
/* UART0 8 pins Only */
|
|
/*sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) | SDR0_PFC1_U0ME_DSR_DTR; */
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) |SDR0_PFC1_U0ME_CTS_RTS; /* Chip Pb */
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0IM_MASK) | SDR0_PFC1_U0IM_8PINS;
|
|
break;
|
|
case L2: /* L2 Selection */
|
|
/* UART0 and UART1 4 pins */
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0IM_MASK) | SDR0_PFC1_U0IM_4PINS;
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U1ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
|
|
break;
|
|
case L3: /* L3 Selection */
|
|
/* UART0 4 pins, UART1 and UART2 2 pins */
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0IM_MASK) | SDR0_PFC1_U0IM_4PINS;
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U1ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
|
|
break;
|
|
case L4: /* L4 Selection */
|
|
/* UART0, UART1, UART2 and UART3 2 pins */
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) | SDR0_PFC1_U0ME_DSR_DTR;
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0IM_MASK) | SDR0_PFC1_U0IM_4PINS;
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U1ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
|
|
break;
|
|
}
|
|
update_uart_ios(uart_configuration, gpio_tab);
|
|
|
|
/* UART Selection in all cases */
|
|
uart_selection_in_fpga(uart_configuration);
|
|
|
|
/* Packet Reject Function Available */
|
|
if (ppc440ep_core_selection[PACKET_REJ_FUNC_AVAIL] == CORE_SELECTED)
|
|
{
|
|
/* Set UPR Bit in SDR0_PFC1 Register */
|
|
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UPR_MASK) | SDR0_PFC1_UPR_ENABLE;
|
|
}
|
|
|
|
/* Packet Reject Function Enable */
|
|
if (ppc440ep_core_selection[PACKET_REJ_FUNC_EN] == CORE_SELECTED)
|
|
{
|
|
mfsdr(SDR0_MFR, sdr0_mfr);
|
|
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_PKT_REJ_MASK) | SDR0_MFR_PKT_REJ_EN;;
|
|
mtsdr(SDR0_MFR, sdr0_mfr);
|
|
}
|
|
|
|
/* Perform effective access to hardware */
|
|
mtsdr(SDR0_PFC1, sdr0_pfc1);
|
|
set_chip_gpio_configuration(GPIO0, gpio_tab);
|
|
set_chip_gpio_configuration(GPIO1, gpio_tab);
|
|
|
|
/* USB2.0 Device Reset must be done after GPIO setting */
|
|
if (ppc440ep_core_selection[USB2_DEVICE] == CORE_SELECTED)
|
|
usb2_device_reset_through_fpga();
|
|
|
|
}
|
|
|