upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/cpc45/cpc45.c

173 lines
3.9 KiB

/*
* (C) Copyright 2001
* Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <mpc824x.h>
#include <asm/processor.h>
#include <pci.h>
int sysControlDisplay(int digit, uchar ascii_code);
extern void Plx9030Init(void);
/* We have to clear the initial data area here. Couldn't have done it
* earlier because DRAM had not been initialized.
*/
int board_pre_init(void)
{
/* enable DUAL UART Mode on CPC45 */
*(uchar*)DUART_DCR |= 0x1; /* set DCM bit */
return 0;
}
int checkboard(void)
{
/*
char revision = BOARD_REV;
*/
ulong busfreq = get_bus_freq(0);
char buf[32];
printf("CPC45 ");
/*
printf("Revision %d ", revision);
*/
printf("Local Bus at %s MHz\n", strmhz(buf, busfreq));
return 0;
}
long int initdram(int board_type)
{
int i, cnt;
volatile uchar * base = CFG_SDRAM_BASE;
volatile ulong * addr;
ulong save[32];
ulong val, ret = 0;
for (i=0, cnt=(CFG_MAX_RAM_SIZE / sizeof(long)) >> 1; cnt > 0; cnt >>= 1) {
addr = (volatile ulong *)base + cnt;
save[i++] = *addr;
*addr = ~cnt;
}
addr = (volatile ulong *)base;
save[i] = *addr;
*addr = 0;
if (*addr != 0) {
*addr = save[i];
goto Done;
}
for (cnt = 1; cnt <= CFG_MAX_RAM_SIZE / sizeof(long); cnt <<= 1) {
addr = (volatile ulong *)base + cnt;
val = *addr;
*addr = save[--i];
if (val != ~cnt) {
ulong new_bank0_end = cnt * sizeof(long) - 1;
ulong mear1 = mpc824x_mpc107_getreg(MEAR1);
ulong emear1 = mpc824x_mpc107_getreg(EMEAR1);
mear1 = (mear1 & 0xFFFFFF00) |
((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
emear1 = (emear1 & 0xFFFFFF00) |
((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
mpc824x_mpc107_setreg(MEAR1, mear1);
mpc824x_mpc107_setreg(EMEAR1, emear1);
ret = cnt * sizeof(long);
goto Done;
}
}
ret = CFG_MAX_RAM_SIZE;
Done:
return ret;
}
/*
* Initialize PCI Devices, report devices found.
*/
#ifndef CONFIG_PCI_PNP
static struct pci_config_table pci_sandpoint_config_table[] = {
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0f, PCI_ANY_ID,
pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
PCI_ENET0_MEMADDR,
PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
{ }
};
#endif
struct pci_controller hose = {
#ifndef CONFIG_PCI_PNP
config_table: pci_sandpoint_config_table,
#endif
};
void pci_init_board(void)
{
pci_mpc824x_init(&hose);
/* init PCI_to_LOCAL Bus BRIDGE */
Plx9030Init();
sysControlDisplay(0,' ');
sysControlDisplay(1,'C');
sysControlDisplay(2,'P');
sysControlDisplay(3,'C');
sysControlDisplay(4,' ');
sysControlDisplay(5,'4');
sysControlDisplay(6,'5');
sysControlDisplay(7,' ');
}
/**************************************************************************
*
* sysControlDisplay - controls one of the Alphanum. Display digits.
*
* This routine will write an ASCII character to the display digit requested.
*
* SEE ALSO:
*
* RETURNS: NA
*/
int sysControlDisplay
(
int digit, /* number of digit 0..7 */
uchar ascii_code /* ASCII code */
)
{
if ((digit < 0) || (digit > 7))
return (-1);
*((volatile uchar*)(DISP_CHR_RAM + digit)) = ascii_code;
return (0);
}