upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/st/stm32mp1/board.c

101 lines
2.2 KiB

// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved
*/
#include <common.h>
#include <dm.h>
#include <asm/io.h>
#include <asm/arch/ddr.h>
#include <power/pmic.h>
#include <power/stpmu1.h>
#ifdef CONFIG_DEBUG_UART_BOARD_INIT
void board_debug_uart_init(void)
{
#if (CONFIG_DEBUG_UART_BASE == STM32_UART4_BASE)
#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00)
#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28)
/* UART4 clock enable */
setbits_le32(RCC_MP_APB1ENSETR, BIT(16));
#define GPIOG_BASE 0x50008000
/* GPIOG clock enable */
writel(BIT(6), RCC_MP_AHB4ENSETR);
/* GPIO configuration for EVAL board
* => Uart4 TX = G11
*/
writel(0xffbfffff, GPIOG_BASE + 0x00);
writel(0x00006000, GPIOG_BASE + 0x24);
#else
#error("CONFIG_DEBUG_UART_BASE: not supported value")
#endif
}
#endif
#ifdef CONFIG_PMIC_STPMU1
int board_ddr_power_init(void)
{
struct udevice *dev;
int ret;
ret = uclass_get_device_by_driver(UCLASS_PMIC,
DM_GET_DRIVER(pmic_stpmu1), &dev);
if (ret)
/* No PMIC on board */
return 0;
/* Set LDO3 to sync mode */
ret = pmic_reg_read(dev, STPMU1_LDOX_CTRL_REG(STPMU1_LDO3));
if (ret < 0)
return ret;
ret &= ~STPMU1_LDO3_MODE;
ret &= ~STPMU1_LDO12356_OUTPUT_MASK;
ret |= STPMU1_LDO3_DDR_SEL << STPMU1_LDO12356_OUTPUT_SHIFT;
ret = pmic_reg_write(dev, STPMU1_LDOX_CTRL_REG(STPMU1_LDO3),
ret);
if (ret < 0)
return ret;
/* Set BUCK2 to 1.35V */
ret = pmic_clrsetbits(dev,
STPMU1_BUCKX_CTRL_REG(STPMU1_BUCK2),
STPMU1_BUCK_OUTPUT_MASK,
STPMU1_BUCK2_1350000V);
if (ret < 0)
return ret;
/* Enable BUCK2 and VREF */
ret = pmic_clrsetbits(dev,
STPMU1_BUCKX_CTRL_REG(STPMU1_BUCK2),
STPMU1_BUCK_EN, STPMU1_BUCK_EN);
if (ret < 0)
return ret;
mdelay(STPMU1_DEFAULT_START_UP_DELAY_MS);
ret = pmic_clrsetbits(dev, STPMU1_VREF_CTRL_REG,
STPMU1_VREF_EN, STPMU1_VREF_EN);
if (ret < 0)
return ret;
mdelay(STPMU1_DEFAULT_START_UP_DELAY_MS);
/* Enable LDO3 */
ret = pmic_clrsetbits(dev,
STPMU1_LDOX_CTRL_REG(STPMU1_LDO3),
STPMU1_LDO_EN, STPMU1_LDO_EN);
if (ret < 0)
return ret;
mdelay(STPMU1_DEFAULT_START_UP_DELAY_MS);
return 0;
}
#endif