upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/liebherr/display5/common.c

120 lines
3.5 KiB

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2017 DENX Software Engineering
* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
*/
#include <asm/mach-imx/iomux-v3.h>
#include <asm/arch/mx6-pins.h>
#include "common.h"
iomux_v3_cfg_t const uart_pads[] = {
/* UART4 */
MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_CSI0_DAT16__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_CSI0_DAT17__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
};
iomux_v3_cfg_t const uart_console_pads[] = {
/* UART5 */
MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_CSI0_DAT15__UART5_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_CSI0_DAT18__UART5_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_CSI0_DAT19__UART5_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
};
void displ5_set_iomux_uart_spl(void)
{
SETUP_IOMUX_PADS(uart_console_pads);
}
void displ5_set_iomux_uart(void)
{
SETUP_IOMUX_PADS(uart_pads);
}
iomux_v3_cfg_t const misc_pads_spl[] = {
/* Emergency recovery pin */
MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
void displ5_set_iomux_misc_spl(void)
{
SETUP_IOMUX_PADS(misc_pads_spl);
}
#ifdef CONFIG_MXC_SPI
iomux_v3_cfg_t const ecspi_pads[] = {
/* SPI3 */
MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_DISP0_DAT3__ECSPI3_SS0 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_DISP0_DAT4__ECSPI3_SS1 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_DISP0_DAT5__ECSPI3_SS2 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_DISP0_DAT6__ECSPI3_SS3 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_DISP0_DAT7__ECSPI3_RDY | MUX_PAD_CTRL(NO_PAD_CTRL),
};
iomux_v3_cfg_t const ecspi2_pads[] = {
/* SPI2, NOR Flash nWP, CS0 */
MX6_PAD_CSI0_DAT10__ECSPI2_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_CSI0_DAT9__ECSPI2_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_CSI0_DAT8__ECSPI2_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_CSI0_DAT11__GPIO5_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
int board_spi_cs_gpio(unsigned int bus, unsigned int cs)
{
if (bus != 1 || cs != (IMX_GPIO_NR(5, 29) << 8))
return -EINVAL;
return IMX_GPIO_NR(5, 29);
}
void displ5_set_iomux_ecspi_spl(void)
{
SETUP_IOMUX_PADS(ecspi2_pads);
}
void displ5_set_iomux_ecspi(void)
{
SETUP_IOMUX_PADS(ecspi_pads);
}
#else
void displ5_set_iomux_ecspi_spl(void) {}
void displ5_set_iomux_ecspi(void) {}
#endif
#ifdef CONFIG_FSL_ESDHC
iomux_v3_cfg_t const usdhc4_pads[] = {
MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_NANDF_ALE__SD4_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
void displ5_set_iomux_usdhc_spl(void)
{
SETUP_IOMUX_PADS(usdhc4_pads);
}
void displ5_set_iomux_usdhc(void)
{
SETUP_IOMUX_PADS(usdhc4_pads);
}
#else
void displ5_set_iomux_usdhc_spl(void) {}
void displ5_set_iomux_usdhc(void) {}
#endif