upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/include/configs/socrates.h

473 lines
15 KiB

/*
* (C) Copyright 2008
* Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com.
*
* Wolfgang Denk <wd@denx.de>
* Copyright 2004 Freescale Semiconductor.
* (C) Copyright 2002,2003 Motorola,Inc.
* Xianghua Xiao <X.Xiao@motorola.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* Socrates
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* new uImage format support */
#define CONFIG_FIT 1
#define CONFIG_OF_LIBFDT 1
#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */
#define CONFIG_MPC8544 1
#define CONFIG_SOCRATES 1
#define CONFIG_SYS_TEXT_BASE 0xfff80000
#define CONFIG_PCI
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
/*
* Only possible on E500 Version 2 or newer cores.
*/
#define CONFIG_ENABLE_36BIT_PHYS 1
/*
* sysclk for MPC85xx
*
* Two valid values are:
* 33000000
* 66000000
*
* Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
* is likely the desired value here, so that is now the default.
* The board, however, can run at 66MHz. In any event, this value
* must match the settings of some switches. Details can be found
* in the README.mpc85xxads.
*/
#ifndef CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_CLK_FREQ 66666666
#endif
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00C00000
#define CONFIG_SYS_CCSRBAR 0xE0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_VERY_BIG_RAM
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 2
/* I2C addresses of SPD EEPROMs */
#define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */
#define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */
/* Hardcoded values, to use instead of SPD */
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102
#define CONFIG_SYS_DDR_TIMING_0 0x00260802
#define CONFIG_SYS_DDR_TIMING_1 0x3935D322
#define CONFIG_SYS_DDR_TIMING_2 0x14904CC8
#define CONFIG_SYS_DDR_MODE 0x00480432
#define CONFIG_SYS_DDR_INTERVAL 0x030C0100
#define CONFIG_SYS_DDR_CONFIG_2 0x04400000
#define CONFIG_SYS_DDR_CONFIG 0xC3008000
#define CONFIG_SYS_DDR_CLK_CONTROL 0x03800000
#define CONFIG_SYS_SDRAM_SIZE 256 /* in Megs */
/*
* Flash on the LocalBus
*/
#define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
#define CONFIG_SYS_FLASH0 0xFE000000
#define CONFIG_SYS_FLASH1 0xFC000000
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 }
#define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */
#define CONFIG_SYS_BR0_PRELIM 0xfe001001 /* port size 16bit */
#define CONFIG_SYS_OR0_PRELIM 0xfe000030 /* 32MB Flash */
#define CONFIG_SYS_BR1_PRELIM 0xfc001001 /* port size 16bit */
#define CONFIG_SYS_OR1_PRELIM 0xfe000030 /* 32MB Flash */
#define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384KiB for Mon */
#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc */
/* FPGA and NAND */
#define CONFIG_SYS_FPGA_BASE 0xc0000000
#define CONFIG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */
#define CONFIG_SYS_HMI_BASE 0xc0010000
#define CONFIG_SYS_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */
#define CONFIG_SYS_OR3_PRELIM 0xfff00000 /* 1 MB */
#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_FPGA_BASE + 0x70)
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_CMD_NAND
/* LIME GDC */
#define CONFIG_SYS_LIME_BASE 0xc8000000
#define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */
#define CONFIG_SYS_BR2_PRELIM 0xc80018a1 /* UPMB, 32-bit */
#define CONFIG_SYS_OR2_PRELIM 0xfc000000 /* 64 MB */
#define CONFIG_VIDEO
#define CONFIG_VIDEO_MB862xx
#define CONFIG_VIDEO_MB862xx_ACCEL
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_CONSOLE_EXTRA_INFO
#define VIDEO_FB_16BPP_PIXEL_SWAP
#define VIDEO_FB_16BPP_WORD_SWAP
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_SPLASH_SCREEN
#define CONFIG_VIDEO_BMP_GZIP
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */
/* SDRAM Clock frequency, 100MHz (0x0000) or 133MHz (0x10000) */
#define CONFIG_SYS_MB862xx_CCF 0x10000
/* SDRAM parameter */
#define CONFIG_SYS_MB862xx_MMR 0x4157BA63
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
#ifdef CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/*
* I2C
*/
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_SYS_I2C_SPEED 102124 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SYS_I2C_OFFSET 0x3000
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C2_OFFSET 0x3100
/* I2C RTC */
#define CONFIG_RTC_RX8025 /* Use Epson rx8025 rtc via i2c */
#define CONFIG_SYS_I2C_RTC_ADDR 0x32 /* at address 0x32 */
/* I2C W83782G HW-Monitoring IC */
#define CONFIG_SYS_I2C_W83782G_ADDR 0x28 /* W83782G address */
/* I2C temp sensor */
/* Socrates uses Maxim's DS75, which is compatible with LM75 */
#define CONFIG_DTT_LM75 1
#define CONFIG_DTT_SENSORS {4} /* Sensor addresses */
#define CONFIG_SYS_DTT_MAX_TEMP 125
#define CONFIG_SYS_DTT_LOW_TEMP -55
#define CONFIG_SYS_DTT_HYSTERESIS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
/*
* General PCI
* Memory space is mapped 1-1.
*/
#define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */
/* PCI is clocked by the external source at 33 MHz */
#define CONFIG_PCI_CLK_FREQ 33000000
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCI1_IO_BASE 0xE2000000
#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */
#if defined(CONFIG_PCI)
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif /* CONFIG_PCI */
#define CONFIG_NET_MULTI 1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC3 1
#define CONFIG_TSEC3_NAME "TSEC1"
#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC3_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC1_FLAGS TSEC_GIGABIT
#define TSEC3_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0,1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
/*
* Environment
*/
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x4000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_TIMESTAMP /* Print image info with ts */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_BMP
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
#undef CONFIG_CMD_EEPROM
#define CONFIG_CMD_EXT2 /* EXT2 Support */
#define CONFIG_CMD_I2C
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_MII
#undef CONFIG_CMD_NFS
#define CONFIG_CMD_PING
#define CONFIG_CMD_SNTP
#define CONFIG_CMD_USB
#define CONFIG_CMD_REGINFO
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buf Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/
#define CONFIG_BOOTDELAY 1 /* -1 disables auto-boot */
#define CONFIG_PREBOOT "echo;" \
"echo Welcome on the ABB Socrates Board;" \
"echo"
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consdev=ttyS0\0" \
"uboot_file=/home/tftp/syscon3/u-boot.bin\0" \
"bootfile=/home/tftp/syscon3/uImage\0" \
"fdt_file=/home/tftp/syscon3/socrates.dtb\0" \
"initrd_file=/home/tftp/syscon3/uinitrd.gz\0" \
"uboot_addr=FFFA0000\0" \
"kernel_addr=FE000000\0" \
"fdt_addr=FE1E0000\0" \
"ramdisk_addr=FE200000\0" \
"fdt_addr_r=B00000\0" \
"kernel_addr_r=200000\0" \
"ramdisk_addr_r=400000\0" \
"rootpath=/opt/eldk/ppc_85xxDP\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath\0" \
"addcons=setenv bootargs $bootargs " \
"console=$consdev,$baudrate\0" \
"addip=setenv bootargs $bootargs " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask" \
":$hostname:$netdev:off panic=1\0" \
"boot_nor=run ramargs addcons;" \
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
"tftp ${fdt_addr_r} ${fdt_file}; " \
"run nfsargs addip addcons;" \
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
"update_uboot=tftp 100000 ${uboot_file};" \
"protect off fffa0000 ffffffff;" \
"era fffa0000 ffffffff;" \
"cp.b 100000 fffa0000 ${filesize};" \
"setenv filesize;saveenv\0" \
"update_kernel=tftp 100000 ${bootfile};" \
"era fe000000 fe1dffff;" \
"cp.b 100000 fe000000 ${filesize};" \
"setenv filesize;saveenv\0" \
"update_fdt=tftp 100000 ${fdt_file};" \
"era fe1e0000 fe1fffff;" \
"cp.b 100000 fe1e0000 ${filesize};" \
"setenv filesize;saveenv\0" \
"update_initrd=tftp 100000 ${initrd_file};" \
"era fe200000 fe9fffff;" \
"cp.b 100000 fe200000 ${filesize};" \
"setenv filesize;saveenv\0" \
"clean_data=era fea00000 fff5ffff\0" \
"usbargs=setenv bootargs root=/dev/sda1 rw\0" \
"load_usb=usb start;" \
"ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \
"boot_usb=run load_usb usbargs addcons;" \
"bootm ${kernel_addr_r} - ${fdt_addr};" \
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
""
#define CONFIG_BOOTCOMMAND "run boot_nor"
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
/* USB support */
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_PCI_OHCI 1
#define CONFIG_PCI_OHCI_DEVNO 3 /* Number in PCI list */
#define CONFIG_PCI_EHCI_DEVNO (CONFIG_PCI_OHCI_DEVNO / 2)
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
#define CONFIG_DOS_PARTITION 1
#define CONFIG_USB_STORAGE 1
#endif /* __CONFIG_H */