upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/drivers/ddr/microchip/ddr2_regs.h

147 lines
3.0 KiB

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (c) 2015 Purna Chandra Mandal <purna.mandal@microchip.com>
*
*/
#ifndef __MICROCHIP_DDR2_REGS_H
#define __MICROCHIP_DDR2_REGS_H
#include <linux/bitops.h>
/* DDR2 Controller */
struct ddr2_ctrl_regs {
u32 tsel;
u32 minlim;
u32 reqprd;
u32 mincmd;
u32 memcon;
u32 memcfg0;
u32 memcfg1;
u32 memcfg2;
u32 memcfg3;
u32 memcfg4;
u32 refcfg;
u32 pwrcfg;
u32 dlycfg0;
u32 dlycfg1;
u32 dlycfg2;
u32 dlycfg3;
u32 odtcfg;
u32 xfercfg;
u32 cmdissue;
u32 odtencfg;
u32 memwidth;
u32 unused[11];
u32 cmd10[16];
u32 cmd20[16];
};
/* Arbiter Config */
#define MIN_LIM_WIDTH 5
#define RQST_PERIOD_WIDTH 8
#define MIN_CMDACPT_WIDTH 8
/* Refresh Config */
#define REFCNT_CLK(x) (x)
#define REFDLY_CLK(x) ((x) << 16)
#define MAX_PEND_REF(x) ((x) << 24)
/* Power Config */
#define PRECH_PWR_DN_ONLY(x) ((x) << 22)
#define SELF_REF_DLY(x) ((x) << 12)
#define PWR_DN_DLY(x) ((x) << 4)
#define EN_AUTO_SELF_REF(x) ((x) << 3)
#define EN_AUTO_PWR_DN(x) ((x) << 2)
#define ERR_CORR_EN(x) ((x) << 1)
#define ECC_EN(x) (x)
/* Memory Width */
#define HALF_RATE_MODE BIT(3)
/* Delay Config */
#define ODTWLEN(x) ((x) << 20)
#define ODTRLEN(x) ((x) << 16)
#define ODTWDLY(x) ((x) << 12)
#define ODTRDLY(x) ((x) << 8)
/* Xfer Config */
#define BIG_ENDIAN(x) ((x) << 31)
#define MAX_BURST(x) ((x) << 24)
#define RDATENDLY(x) ((x) << 16)
#define NXDATAVDLY(x) ((x) << 4)
#define NXTDATRQDLY(x) ((x) << 0)
/* Host Commands */
#define IDLE_NOP 0x00ffffff
#define PRECH_ALL_CMD 0x00fff401
#define REF_CMD 0x00fff801
#define LOAD_MODE_CMD 0x00fff001
#define CKE_LOW 0x00ffeffe
#define NUM_HOST_CMDS 12
/* Host CMD Issue */
#define CMD_VALID BIT(4)
#define NUMHOSTCMD(x) (x)
/* Memory Control */
#define INIT_DONE BIT(1)
#define INIT_START BIT(0)
/* Address Control */
#define EN_AUTO_PRECH 0
#define SB_PRI 1
/* DDR2 Phy Register */
struct ddr2_phy_regs {
u32 scl_start;
u32 unused1[2];
u32 scl_latency;
u32 unused2[2];
u32 scl_config_1;
u32 scl_config_2;
u32 pad_ctrl;
u32 dll_recalib;
};
/* PHY PAD CONTROL */
#define ODT_SEL BIT(0)
#define ODT_EN BIT(1)
#define DRIVE_SEL(x) ((x) << 2)
#define ODT_PULLDOWN(x) ((x) << 4)
#define ODT_PULLUP(x) ((x) << 6)
#define EXTRA_OEN_CLK(x) ((x) << 8)
#define NOEXT_DLL BIT(9)
#define DLR_DFT_WRCMD BIT(13)
#define HALF_RATE BIT(14)
#define DRVSTR_PFET(x) ((x) << 16)
#define DRVSTR_NFET(x) ((x) << 20)
#define RCVR_EN BIT(28)
#define PREAMBLE_DLY(x) ((x) << 29)
/* PHY DLL RECALIBRATE */
#define RECALIB_CNT(x) ((x) << 8)
#define DISABLE_RECALIB(x) ((x) << 26)
#define DELAY_START_VAL(x) ((x) << 28)
/* PHY SCL CONFIG1 */
#define SCL_BURST8 BIT(0)
#define SCL_DDR_CONNECTED BIT(1)
#define SCL_RCAS_LAT(x) ((x) << 4)
#define SCL_ODTCSWW BIT(24)
/* PHY SCL CONFIG2 */
#define SCL_CSEN BIT(0)
#define SCL_WCAS_LAT(x) ((x) << 8)
/* PHY SCL Latency */
#define SCL_CAPCLKDLY(x) ((x) << 0)
#define SCL_DDRCLKDLY(x) ((x) << 4)
/* PHY SCL START */
#define SCL_START BIT(28)
#define SCL_EN BIT(26)
#define SCL_LUBPASS (BIT(1) | BIT(0))
#endif /* __MICROCHIP_DDR2_REGS_H */