upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/nvidia/dalmore/dalmore.c

101 lines
2.7 KiB

/*
* Copyright (c) 2010-2013, NVIDIA CORPORATION. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include <common.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/gp_padctrl.h>
#include "pinmux-config-dalmore.h"
#include <i2c.h>
#define BAT_I2C_ADDRESS 0x48 /* TPS65090 charger */
#define PMU_I2C_ADDRESS 0x58 /* TPS65913 PMU */
/*
* Routine: pinmux_init
* Description: Do individual peripheral pinmux configs
*/
void pinmux_init(void)
{
pinmux_config_table(tegra114_pinmux_set_nontristate,
ARRAY_SIZE(tegra114_pinmux_set_nontristate));
pinmux_config_table(tegra114_pinmux_common,
ARRAY_SIZE(tegra114_pinmux_common));
pinmux_config_table(unused_pins_lowpower,
ARRAY_SIZE(unused_pins_lowpower));
/* Initialize any non-default pad configs (APB_MISC_GP regs) */
padgrp_config_table(dalmore_padctrl, ARRAY_SIZE(dalmore_padctrl));
}
#if defined(CONFIG_TEGRA_MMC)
/*
* Do I2C/PMU writes to bring up SD card bus power
*
*/
void board_sdmmc_voltage_init(void)
{
uchar reg, data_buffer[1];
int ret;
ret = i2c_set_bus_num(0);/* PMU is on bus 0 */
if (ret)
printf("%s: i2c_set_bus_num returned %d\n", __func__, ret);
/* TPS65913: LDO9_VOLTAGE = 3.3V */
data_buffer[0] = 0x31;
reg = 0x61;
ret = i2c_write(PMU_I2C_ADDRESS, reg, 1, data_buffer, 1);
if (ret)
printf("%s: PMU i2c_write %02X<-%02X returned %d\n",
__func__, reg, data_buffer[0], ret);
/* TPS65913: LDO9_CTRL = Active */
data_buffer[0] = 0x01;
reg = 0x60;
ret = i2c_write(PMU_I2C_ADDRESS, reg, 1, data_buffer, 1);
if (ret)
printf("%s: PMU i2c_write %02X<-%02X returned %d\n",
__func__, reg, data_buffer[0], ret);
/* TPS65090: FET6_CTRL = enable output auto discharge, enable FET6 */
data_buffer[0] = 0x03;
reg = 0x14;
ret = i2c_write(BAT_I2C_ADDRESS, reg, 1, data_buffer, 1);
if (ret)
printf("%s: BAT i2c_write %02X<-%02X returned %d\n",
__func__, reg, data_buffer[0], ret);
}
/*
* Routine: pin_mux_mmc
* Description: setup the MMC muxes, power rails, etc.
*/
void pin_mux_mmc(void)
{
/*
* NOTE: We don't do mmc-specific pin muxes here.
* They were done globally in pinmux_init().
*/
/* Bring up the SDIO3 power rail */
board_sdmmc_voltage_init();
}
#endif /* MMC */