upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/doc/README.fsl-ddr

3.2 KiB


Table of interleaving modes supported in cpu/8xxx/ddr/
======================================================
+-------------+---------------------------------------------------------+
| | Rank Interleaving |
| +--------+-----------+-----------+------------+-----------+
|Memory | | | | 2x2 | 4x1 |
|Controller | None | 2x1 lower | 2x1 upper | {CS0+CS1}, | {CS0+CS1+ |
|Interleaving | | {CS0+CS1} | {CS2+CS3} | {CS2+CS3} | CS2+CS3} |
+-------------+--------+-----------+-----------+------------+-----------+
|None | Yes | Yes | Yes | Yes | Yes |
+-------------+--------+-----------+-----------+------------+-----------+
|Cacheline | Yes | Yes | No | No, Only(*)| Yes |
| |CS0 Only| | | {CS0+CS1} | |
+-------------+--------+-----------+-----------+------------+-----------+
|Page | Yes | Yes | No | No, Only(*)| Yes |
| |CS0 Only| | | {CS0+CS1} | |
+-------------+--------+-----------+-----------+------------+-----------+
|Bank | Yes | Yes | No | No, Only(*)| Yes |
| |CS0 Only| | | {CS0+CS1} | |
+-------------+--------+-----------+-----------+------------+-----------+
|Superbank | No | Yes | No | No, Only(*)| Yes |
| | | | | {CS0+CS1} | |
+-------------+--------+-----------+-----------+------------+-----------+
(*) Although the hardware can be configured with memory controller
interleaving using "2x2" rank interleaving, it only interleaves {CS0+CS1}
from each controller. {CS2+CS3} on each controller are only rank
interleaved on that controller.

The ways to configure the ddr interleaving mode
==============================================
1. In board header file(e.g.MPC8572DS.h), add default interleaving setting
under "CONFIG_EXTRA_ENV_SETTINGS", like:
#define CONFIG_EXTRA_ENV_SETTINGS \
"memctl_intlv_ctl=2\0" \
......

2. Run u-boot "setenv" command to configure the memory interleaving mode.
Either numerical or string value is accepted.

# disable memory controller interleaving
setenv memctl_intlv_ctl

# cacheline interleaving
setenv memctl_intlv_ctl 0 or setenv memctl_intlv_ctl cacheline

# page interleaving
setenv memctl_intlv_ctl 1 or setenv memctl_intlv_ctl page

# bank interleaving
setenv memctl_intlv_ctl 2 or setenv memctl_intlv_ctl bank

# superbank
setenv memctl_intlv_ctl 3 or setenv memctl_intlv_ctl superbank

# disable bank (chip-select) interleaving
setenv ba_intlv_ctl

# bank(chip-select) interleaving cs0+cs1
setenv ba_intlv_ctl 0x40 or setenv ba_intlv_ctl cs0_cs1

# bank(chip-select) interleaving cs2+cs3
setenv ba_intlv_ctl 0x20 or setenv ba_intlv_ctl cs2_cs3

# bank(chip-select) interleaving (cs0+cs1) and (cs2+cs3) (2x2)
setenv ba_intlv_ctl 0x60 or setenv ba_intlv_ctl cs0_cs1_and_cs2_cs3

# bank(chip-select) interleaving (cs0+cs1+cs2+cs3) (4x1)
setenv ba_intlv_ctl 0x04 or setenv ba_intlv_ctl cs0_cs1_cs2_cs3