|
|
|
|
Freescale MPC8641HPCN board
|
|
|
|
|
===========================
|
|
|
|
|
|
|
|
|
|
Created 05/24/2006 Haiying Wang
|
|
|
|
|
-------------------------------
|
|
|
|
|
|
|
|
|
|
1. Building U-Boot
|
|
|
|
|
------------------
|
|
|
|
|
The 86xx HPCN code base is known to compile using:
|
|
|
|
|
Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3
|
|
|
|
|
|
|
|
|
|
$ make MPC8641HPCN_config
|
|
|
|
|
Configuring for MPC8641HPCN board...
|
|
|
|
|
|
|
|
|
|
$ make
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2. Switch and Jumper Setting
|
|
|
|
|
----------------------------
|
|
|
|
|
Jumpers:
|
|
|
|
|
J14 Pins 1-2 (near plcc32 socket)
|
|
|
|
|
|
|
|
|
|
Switches:
|
|
|
|
|
SW1(1-5) = 01100 CONFIG_SYS_COREPLL = 01000 :: CORE = 2:1
|
|
|
|
|
01100 :: CORE = 2.5:1
|
|
|
|
|
10000 :: CORE = 3:1
|
|
|
|
|
11100 :: CORE = 3.5:1
|
|
|
|
|
10100 :: CORE = 4:1
|
|
|
|
|
01110 :: CORE = 4.5:1
|
|
|
|
|
SW1(6-8) = 001 CONFIG_SYS_SYSCLK = 000 :: SYSCLK = 33MHz
|
|
|
|
|
001 :: SYSCLK = 40MHz
|
|
|
|
|
|
|
|
|
|
SW2(1-4) = 1100 CONFIG_SYS_CCBPLL = 0010 :: 2X
|
|
|
|
|
0100 :: 4X
|
|
|
|
|
0110 :: 6X
|
|
|
|
|
1000 :: 8X
|
|
|
|
|
1010 :: 10X
|
|
|
|
|
1100 :: 12X
|
|
|
|
|
1110 :: 14X
|
|
|
|
|
0000 :: 16X
|
|
|
|
|
SW2(5-8) = 1110 CONFIG_SYS_BOOTLOC = 1110 :: boot 16-bit localbus
|
|
|
|
|
|
|
|
|
|
SW3(1-7) = 0011000 CONFIG_SYS_VID = 0011000 :: VCORE = 1.2V
|
|
|
|
|
0100000 :: VCORE = 1.11V
|
|
|
|
|
SW3(8) = 0 VCC_PLAT = 0 :: VCC_PLAT = 1.2V
|
|
|
|
|
1 :: VCC_PLAT = 1.0V
|
|
|
|
|
|
|
|
|
|
SW4(1-2) = 11 CONFIG_SYS_HOSTMODE = 11 :: both prots host/root
|
|
|
|
|
SW4(3-4) = 11 CONFIG_SYS_BOOTSEQ = 11 :: no boot seq
|
|
|
|
|
SW4(5-8) = 0011 CONFIG_SYS_IOPORT = 0011 :: both PEX
|
|
|
|
|
|
|
|
|
|
SW5(1) = 1 CONFIG_SYS_FLASHMAP = 1 :: boot from flash
|
|
|
|
|
0 :: boot from PromJet
|
|
|
|
|
SW5(2) = 1 CONFIG_SYS_FLASHBANK = 1 :: swap upper/lower
|
|
|
|
|
halves (virtual banks)
|
|
|
|
|
0 :: normal
|
|
|
|
|
SW5(3) = 0 CONFIG_SYS_FLASHWP = 0 :: not protected
|
|
|
|
|
SW5(4) = 0 CONFIG_SYS_PORTDIV = 1 :: 2:1 for PD4
|
|
|
|
|
1:1 for PD6
|
|
|
|
|
SW5(5-6) = 11 CONFIG_SYS_PIXISOPT = 11 :: s/w determined
|
|
|
|
|
SW5(7-8) = 11 CONFIG_SYS_LADOPT = 11 :: s/w determined
|
|
|
|
|
|
|
|
|
|
SW6(1) = 1 CONFIG_SYS_CPUBOOT = 1 :: no boot holdoff
|
|
|
|
|
SW6(2) = 1 CONFIG_SYS_BOOTADDR = 1 :: no traslation
|
|
|
|
|
SW6(3-5) = 000 CONFIG_SYS_REFCLKSEL = 000 :: 100MHZ
|
|
|
|
|
SW6(6) = 1 CONFIG_SYS_SERROM_ADDR= 1 ::
|
|
|
|
|
SW6(7) = 1 CONFIG_SYS_MEMDEBUG = 1 ::
|
|
|
|
|
SW6(8) = 1 CONFIG_SYS_DDRDEBUG = 1 ::
|
|
|
|
|
|
|
|
|
|
SW8(1) = 1 ACZ_SYNC = 1 :: 48MHz on TP49
|
|
|
|
|
SW8(2) = 1 ACB_SYNC = 1 :: THRMTRIP disabled
|
|
|
|
|
SW8(3) = 1 ACZ_SDOUT = 1 :: p4 mode
|
|
|
|
|
SW8(4) = 1 ACB_SDOUT = 1 :: PATA freq. = 133MHz
|
|
|
|
|
SW8(5) = 0 SUSLED = 0 :: SouthBridge Mode
|
|
|
|
|
SW8(6) = 0 SPREAD = 0 :: REFCLK SSCG Disabled
|
|
|
|
|
SW8(7) = 1 ACPWR = 1 :: non-battery
|
|
|
|
|
SW8(8) = 0 CONFIG_SYS_IDWP = 0 :: write enable
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3. Flash U-Boot
|
|
|
|
|
---------------
|
|
|
|
|
The flash range 0xFF800000 to 0xFFFFFFFF can be divided into 2 halves.
|
|
|
|
|
It is possible to use either half to boot using u-boot. Switch 5 bit 2
|
|
|
|
|
is used for this purpose.
|
|
|
|
|
|
|
|
|
|
0xFF800000 to 0xFFBFFFFF - 4MB
|
|
|
|
|
0xFFC00000 to 0xFFFFFFFF - 4MB
|
|
|
|
|
When this bit is 0, U-Boot is at 0xFFF00000.
|
|
|
|
|
When this bit is 1, U-Boot is at 0xFFB00000.
|
|
|
|
|
|
|
|
|
|
Use the above mentioned flash commands to program the other half, and
|
|
|
|
|
use switch 5, bit 2 to alternate between the halves. Note: The booting
|
|
|
|
|
version of U-Boot will always be at 0xFFF00000.
|
|
|
|
|
|
|
|
|
|
To Flash U-Boot into the booting bank (0xFFC00000 - 0xFFFFFFFF):
|
|
|
|
|
|
|
|
|
|
tftp 1000000 u-boot.bin
|
|
|
|
|
protect off all
|
|
|
|
|
erase fff00000 +$filesize
|
|
|
|
|
cp.b 1000000 fff00000 $filesize
|
|
|
|
|
|
|
|
|
|
or use tftpflash command:
|
|
|
|
|
run tftpflash
|
|
|
|
|
|
|
|
|
|
To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF):
|
|
|
|
|
|
|
|
|
|
tftp 1000000 u-boot.bin
|
|
|
|
|
erase ffb00000 +$filesize
|
|
|
|
|
cp.b 1000000 ffb00000 $filesize
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4. Memory Map
|
|
|
|
|
-------------
|
|
|
|
|
|
|
|
|
|
Memory Range Device Size
|
|
|
|
|
------------ ------ ----
|
|
|
|
|
0x0000_0000 0x7fff_ffff DDR 2G
|
|
|
|
|
0x8000_0000 0x9fff_ffff PCI1/PEX1 MEM 512M
|
|
|
|
|
0xa000_0000 0xafff_ffff PCI2/PEX2 MEM 512M
|
|
|
|
|
0xf800_0000 0xf80f_ffff CCSR 1M
|
|
|
|
|
0xf810_0000 0xf81f_ffff PIXIS 1M
|
|
|
|
|
0xf840_0000 0xf840_3fff Stack space 32K
|
|
|
|
|
0xe200_0000 0xe2ff_ffff PCI1/PEX1 IO 16M
|
|
|
|
|
0xe300_0000 0xe3ff_ffff PCI2/PEX2 IO 16M
|
|
|
|
|
0xfe00_0000 0xfeff_ffff Flash(alternate)16M
|
|
|
|
|
0xff00_0000 0xffff_ffff Flash(boot bank)16M
|
|
|
|
|
|
|
|
|
|
5. pixis_reset command
|
|
|
|
|
--------------------
|
|
|
|
|
A new command, "pixis_reset", is introduced to reset mpc8641hpcn board
|
|
|
|
|
using the FPGA sequencer. When the board restarts, it has the option
|
|
|
|
|
of using either the current or alternate flash bank as the boot
|
|
|
|
|
image, with or without the watchdog timer enabled, and finally with
|
|
|
|
|
or without frequency changes.
|
|
|
|
|
|
|
|
|
|
Usage is;
|
|
|
|
|
|
|
|
|
|
pixis_reset
|
|
|
|
|
pixis_reset altbank
|
|
|
|
|
pixis_reset altbank wd
|
|
|
|
|
pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
|
|
|
|
|
pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
|
|
|
|
|
|
|
|
|
|
Examples;
|
|
|
|
|
|
|
|
|
|
/* reset to current bank, like "reset" command */
|
|
|
|
|
pixis_reset
|
|
|
|
|
|
|
|
|
|
/* reset board but use the to alternate flash bank */
|
|
|
|
|
pixis_reset altbank
|
|
|
|
|
|
|
|
|
|
/* reset board, use alternate flash bank with watchdog timer enabled*/
|
|
|
|
|
pixis_reset altbank wd
|
|
|
|
|
|
|
|
|
|
/* reset board to alternate bank with frequency changed.
|
|
|
|
|
* 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio
|
|
|
|
|
*/
|
|
|
|
|
pixis-reset altbank cf 40 2.5 10
|
|
|
|
|
|
|
|
|
|
Valid clock choices are in the 8641 Reference Manuals.
|
