|
|
|
|
The supported features of the SBC8240/8245 board are:
|
|
|
|
|
8240 or 8245 processor
|
|
|
|
|
66MHz & 100MHz bus speed
|
|
|
|
|
Decrementer timer
|
|
|
|
|
1 UART channel (Console channel)
|
|
|
|
|
8240 Interrupt Controller
|
|
|
|
|
8240 PCI bridge
|
|
|
|
|
8240 Memory Controller
|
|
|
|
|
SDRAM (16, 64 MB Memory DIMM)
|
|
|
|
|
FLASH 512K On board
|
|
|
|
|
FLASH 4MB On board
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Memory Map from CPU point of view:
|
|
|
|
|
|
|
|
|
|
Start Size Access to
|
|
|
|
|
-----------------------------------------------------
|
|
|
|
|
0x00000000 64MB SDRAM DIMM
|
|
|
|
|
0xFF000000 4MB On Board FLASH
|
|
|
|
|
0xFFF00000 512K On Board FLASH or SRAM (Configured by jumper)
|
|
|
|
|
0xFFE00000 8K EEPROM
|
|
|
|
|
0xFFE80000 8Bit LED
|
|
|
|
|
0xFFF80000 8Bit UART
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Setting the board Jumpers & Switches:
|
|
|
|
|
|
|
|
|
|
In order to get the board running with the default configuration the
|
|
|
|
|
jumpers need to be set as follows:
|
|
|
|
|
|
|
|
|
|
General Jumpers:
|
|
|
|
|
____________________________________________
|
|
|
|
|
| Jumpers | Jumpers | Jumpers |
|
|
|
|
|
|-------------|--------------|---------------|
|
|
|
|
|
|JP1 1-2 | JP14 1-2 | JP27 1-2 |
|
|
|
|
|
|JP5 Open | JP15 1-2 | JP28 2-3 |
|
|
|
|
|
|JP8 1-2 | JP16 1-2 | JP33 Open |
|
|
|
|
|
|JP9 1-2 | JP17 1-2 | JP37 Close |
|
|
|
|
|
|JP10 1-2 | JP18 1-2 | |
|
|
|
|
|
|JP11 2-3 | JP19 1-2 | |
|
|
|
|
|
|JP12 1-2 | JP20 1-2 | |
|
|
|
|
|
|JP13 1-2 | JP25 Open | |
|
|
|
|
|
|_____________|______________|_______________|
|
|
|
|
|
|
|
|
|
|
Bus speed Jumpers:
|
|
|
|
|
_________________________
|
|
|
|
|
| 100MHz Bus | 66 MHz Bus |
|
|
|
|
|
|------------|------------|
|
|
|
|
|
| JP2 1-2 | JP2 1-2 |
|
|
|
|
|
| JP3 1-2 | JP3 2-3 |
|
|
|
|
|
| JP4 1-2 | JP4 2-3 |
|
|
|
|
|
| JP6 1-2 | JP6 2-3 |
|
|
|
|
|
| JP7 1-2 | JP7 1-2 |
|
|
|
|
|
|____________|____________|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
U-Boot 1.1.2 (Jun 24 2004 - 17:01:04)
|
|
|
|
|
|
|
|
|
|
CPU: MPC8240 Revision 1.1 at 247.500 MHz: 16 kB I-Cache 16 kB D-Cache
|
|
|
|
|
Board: sbc8240 Revision 255 Local Bus at 99 MHz
|
|
|
|
|
DRAM: 64 MB
|
|
|
|
|
FLASH: 512 kB
|
|
|
|
|
00 11 8086 1229 0200 00
|
|
|
|
|
In: serial
|
|
|
|
|
Out: serial
|
|
|
|
|
Err: serial
|
|
|
|
|
Net: i82559#0
|
|
|
|
|
|
|
|
|
|
Welcome to U-Boot for the sbc8240
|
|
|
|
|
|
|
|
|
|
Type ? or help to get on-line help
|
|
|
|
|
|
|
|
|
|
Hit any key to stop autoboot: 0
|
|
|
|
|
=> printenv
|
|
|
|
|
bootcmd=version;echo;tftpboot $loadaddr $loadfile;bootvx
|
|
|
|
|
bootdelay=5
|
|
|
|
|
baudrate=9600
|
|
|
|
|
ethaddr=DE:AD:BE:EF:01:01
|
|
|
|
|
ipaddr=192.168.193.102
|
|
|
|
|
preboot=echo;echo Welcome to U-Boot for the sbc8240;echo;echo Type "? or help" to get on-line help;echo
|
|
|
|
|
netmask=255.255.255.248
|
|
|
|
|
clocks_in_mhz=1
|
|
|
|
|
bootargs=$fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 tn=sbc8240 o=fei
|
|
|
|
|
ipaddr=192.168.193.102
|
|
|
|
|
loadfile=vxWorks.st
|
|
|
|
|
loadaddr=0x01000000
|
|
|
|
|
net_load=tftpboot $loadaddr $loadfile
|
|
|
|
|
serverip=192.168.193.99
|
|
|
|
|
ethact=i82559#0
|
|
|
|
|
stdin=serial
|
|
|
|
|
stdout=serial
|
|
|
|
|
stderr=serial
|
|
|
|
|
|
|
|
|
|
Environment size: 631/16380 bytes
|
|
|
|
|
=> boot
|
|
|
|
|
|
|
|
|
|
U-Boot 1.1.2 (Jun 24 2004 - 17:01:04)
|
|
|
|
|
|
|
|
|
|
Using i82559#0 device
|
|
|
|
|
TFTP from server 192.168.193.99; our IP address is 192.168.193.102
|
|
|
|
|
Filename 'vxWorks.st'.
|
|
|
|
|
Load address: 0x1000000
|
|
|
|
|
Loading: #################################################################
|
|
|
|
|
#################################################################
|
|
|
|
|
##############################################################
|
|
|
|
|
done
|
|
|
|
|
Bytes transferred = 979927 (ef3d7 hex)
|
|
|
|
|
## Ethernet MAC address not copied to NV RAM
|
|
|
|
|
Loading .text @ 0x00100000 (758848 bytes)
|
|
|
|
|
Loading .data @ 0x001b9440 (79904 bytes)
|
|
|
|
|
Clearing .bss @ 0x001ccc60 (20288 bytes)
|
|
|
|
|
## Using bootline (@ 0x4200): $fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 tn=sbc8240 o=fei
|
|
|
|
|
## Starting vxWorks at 0x00100000 ...
|
|
|
|
|
|
|
|
|
|
Adding 2845 symbols for standalone.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
|
|
|
|
|
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
|
|
|
|
|
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
|
|
|
|
|
]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R)
|
|
|
|
|
] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]]
|
|
|
|
|
]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]]
|
|
|
|
|
]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]]
|
|
|
|
|
]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]]
|
|
|
|
|
]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]]
|
|
|
|
|
]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]]
|
|
|
|
|
]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]]
|
|
|
|
|
]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]]
|
|
|
|
|
]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]
|
|
|
|
|
]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System
|
|
|
|
|
]]]]]]]]]]]]]]]]]]]]]]]]]]]]
|
|
|
|
|
]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks version 5.5.1
|
|
|
|
|
]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.6
|
|
|
|
|
]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2003
|
|
|
|
|
|
|
|
|
|
CPU: MPC8240 -- Wind River BSP. SBC8240 Board. Processor #0.
|
|
|
|
|
Memory Size: 0x2000000. BSP version 1.2/28.
|
|
|
|
|
|
|
|
|
|
->
|
