|
|
|
/*
|
|
|
|
* Copyright 2008 Freescale Semiconductor, Inc.
|
|
|
|
*
|
|
|
|
* This program is free software; you can redistribute it and/or
|
|
|
|
* modify it under the terms of the GNU General Public License
|
|
|
|
* Version 2 as published by the Free Software Foundation.
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <common.h>
|
|
|
|
#include <asm/fsl_ddr_sdram.h>
|
|
|
|
|
|
|
|
#include "ddr.h"
|
|
|
|
|
|
|
|
/* Board-specific functions defined in each board's ddr.c */
|
|
|
|
extern void fsl_ddr_board_options(memctl_options_t *popts,
|
|
|
|
dimm_params_t *pdimm,
|
|
|
|
unsigned int ctrl_num);
|
|
|
|
|
|
|
|
unsigned int populate_memctl_options(int all_DIMMs_registered,
|
|
|
|
memctl_options_t *popts,
|
|
|
|
dimm_params_t *pdimm,
|
|
|
|
unsigned int ctrl_num)
|
|
|
|
{
|
|
|
|
unsigned int i;
|
|
|
|
const char *p;
|
|
|
|
|
|
|
|
/* Chip select options. */
|
|
|
|
|
|
|
|
/* Pick chip-select local options. */
|
|
|
|
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
|
|
|
|
/* If not DDR2, odt_rd_cfg and odt_wr_cfg need to be 0. */
|
|
|
|
|
|
|
|
/* only for single CS? */
|
|
|
|
popts->cs_local_opts[i].odt_rd_cfg = 0;
|
|
|
|
|
|
|
|
popts->cs_local_opts[i].odt_wr_cfg = 1;
|
|
|
|
popts->cs_local_opts[i].auto_precharge = 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Pick interleaving mode. */
|
|
|
|
|
|
|
|
/*
|
|
|
|
* 0 = no interleaving
|
|
|
|
* 1 = interleaving between 2 controllers
|
|
|
|
*/
|
|
|
|
popts->memctl_interleaving = 0;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* 0 = cacheline
|
|
|
|
* 1 = page
|
|
|
|
* 2 = (logical) bank
|
|
|
|
* 3 = superbank (only if CS interleaving is enabled)
|
|
|
|
*/
|
|
|
|
popts->memctl_interleaving_mode = 0;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* 0: cacheline: bit 30 of the 36-bit physical addr selects the memctl
|
|
|
|
* 1: page: bit to the left of the column bits selects the memctl
|
|
|
|
* 2: bank: bit to the left of the bank bits selects the memctl
|
|
|
|
* 3: superbank: bit to the left of the chip select selects the memctl
|
|
|
|
*
|
|
|
|
* NOTE: ba_intlv (rank interleaving) is independent of memory
|
|
|
|
* controller interleaving; it is only within a memory controller.
|
|
|
|
* Must use superbank interleaving if rank interleaving is used and
|
|
|
|
* memory controller interleaving is enabled.
|
|
|
|
*/
|
|
|
|
|
|
|
|
/*
|
|
|
|
* 0 = no
|
|
|
|
* 0x40 = CS0,CS1
|
|
|
|
* 0x20 = CS2,CS3
|
|
|
|
* 0x60 = CS0,CS1 + CS2,CS3
|
|
|
|
* 0x04 = CS0,CS1,CS2,CS3
|
|
|
|
*/
|
|
|
|
popts->ba_intlv_ctl = 0;
|
|
|
|
|
|
|
|
/* Memory Organization Parameters */
|
|
|
|
popts->registered_dimm_en = all_DIMMs_registered;
|
|
|
|
|
|
|
|
/* Operational Mode Paramters */
|
|
|
|
|
|
|
|
/* Pick ECC modes */
|
|
|
|
#ifdef CONFIG_DDR_ECC
|
|
|
|
popts->ECC_mode = 1; /* 0 = disabled, 1 = enabled */
|
|
|
|
#else
|
|
|
|
popts->ECC_mode = 0; /* 0 = disabled, 1 = enabled */
|
|
|
|
#endif
|
|
|
|
popts->ECC_init_using_memctl = 1; /* 0 = use DMA, 1 = use memctl */
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Choose DQS config
|
|
|
|
* 0 for DDR1
|
|
|
|
* 1 for DDR2
|
|
|
|
*/
|
|
|
|
#if defined(CONFIG_FSL_DDR1)
|
|
|
|
popts->DQS_config = 0;
|
|
|
|
#elif defined(CONFIG_FSL_DDR2)
|
|
|
|
popts->DQS_config = 1;
|
|
|
|
#else
|
|
|
|
#error "Fix DQS for DDR3"
|
|
|
|
#endif
|
|
|
|
|
|
|
|
/* Choose self-refresh during sleep. */
|
|
|
|
popts->self_refresh_in_sleep = 1;
|
|
|
|
|
|
|
|
/* Choose dynamic power management mode. */
|
|
|
|
popts->dynamic_power = 0;
|
|
|
|
|
|
|
|
/* 0 = 64-bit, 1 = 32-bit, 2 = 16-bit */
|
|
|
|
popts->data_bus_width = 0;
|
|
|
|
|
|
|
|
/* Choose burst length. */
|
|
|
|
popts->burst_length = 4; /* has to be 4 for DDR2 */
|
|
|
|
|
|
|
|
/* Global Timing Parameters. */
|
|
|
|
debug("mclk_ps = %u ps\n", get_memory_clk_period_ps());
|
|
|
|
|
|
|
|
/* Pick a caslat override. */
|
|
|
|
popts->cas_latency_override = 0;
|
|
|
|
popts->cas_latency_override_value = 3;
|
|
|
|
if (popts->cas_latency_override) {
|
|
|
|
debug("using caslat override value = %u\n",
|
|
|
|
popts->cas_latency_override_value);
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Decide whether to use the computed derated latency */
|
|
|
|
popts->use_derated_caslat = 0;
|
|
|
|
|
|
|
|
/* Choose an additive latency. */
|
|
|
|
popts->additive_latency_override = 0;
|
|
|
|
popts->additive_latency_override_value = 3;
|
|
|
|
if (popts->additive_latency_override) {
|
|
|
|
debug("using additive latency override value = %u\n",
|
|
|
|
popts->additive_latency_override_value);
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* 2T_EN setting
|
|
|
|
*
|
|
|
|
* Factors to consider for 2T_EN:
|
|
|
|
* - number of DIMMs installed
|
|
|
|
* - number of components, number of active ranks
|
|
|
|
* - how much time you want to spend playing around
|
|
|
|
*/
|
|
|
|
popts->twoT_en = 1;
|
|
|
|
popts->threeT_en = 0;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* BSTTOPRE precharge interval
|
|
|
|
*
|
|
|
|
* Set this to 0 for global auto precharge
|
|
|
|
*
|
|
|
|
* FIXME: Should this be configured in picoseconds?
|
|
|
|
* Why it should be in ps: better understanding of this
|
|
|
|
* relative to actual DRAM timing parameters such as tRAS.
|
|
|
|
* e.g. tRAS(min) = 40 ns
|
|
|
|
*/
|
|
|
|
popts->bstopre = 0x100;
|
|
|
|
|
|
|
|
/* Minimum CKE pulse width -- tCKE(MIN) */
|
|
|
|
popts->tCKE_clock_pulse_width_ps
|
|
|
|
= mclk_to_picos(FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Window for four activates -- tFAW
|
|
|
|
*
|
|
|
|
* FIXME: UM: applies only to DDR2/DDR3 with eight logical banks only
|
|
|
|
* FIXME: varies depending upon number of column addresses or data
|
|
|
|
* FIXME: width, was considering looking at pdimm->primary_sdram_width
|
|
|
|
*/
|
|
|
|
#if defined(CONFIG_FSL_DDR1)
|
|
|
|
popts->tFAW_window_four_activates_ps = mclk_to_picos(1);
|
|
|
|
|
|
|
|
#elif defined(CONFIG_FSL_DDR2)
|
|
|
|
/*
|
|
|
|
* x4/x8; some datasheets have 35000
|
|
|
|
* x16 wide columns only? Use 50000?
|
|
|
|
*/
|
|
|
|
popts->tFAW_window_four_activates_ps = 37500;
|
|
|
|
|
|
|
|
#elif defined(CONFIG_FSL_DDR3)
|
|
|
|
#error "FIXME determine four activates for DDR3"
|
|
|
|
#endif
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Check interleaving configuration from environment.
|
|
|
|
* Please refer to doc/README.fsl-ddr for the detail.
|
|
|
|
*
|
|
|
|
* If memory controller interleaving is enabled, then the data
|
|
|
|
* bus widths must be programmed identically for the 2 memory
|
|
|
|
* controllers.
|
|
|
|
*
|
|
|
|
* XXX: Attempt to set both controllers to the same chip select
|
|
|
|
* interleaving mode. It will do a best effort to get the
|
|
|
|
* requested ranks interleaved together such that the result
|
|
|
|
* should be a subset of the requested configuration.
|
|
|
|
*/
|
|
|
|
if ((p = getenv("memctl_intlv_ctl")) != NULL) {
|
|
|
|
if (pdimm[0].n_ranks == 0) {
|
|
|
|
printf("There is no rank on CS0. Because only rank on "
|
|
|
|
"CS0 and ranks chip-select interleaved with CS0"
|
|
|
|
" are controller interleaved, force non memory "
|
|
|
|
"controller interleaving\n");
|
|
|
|
popts->memctl_interleaving = 0;
|
|
|
|
} else {
|
|
|
|
popts->memctl_interleaving = 1;
|
|
|
|
if (strcmp(p, "cacheline") == 0)
|
|
|
|
popts->memctl_interleaving_mode =
|
|
|
|
FSL_DDR_CACHE_LINE_INTERLEAVING;
|
|
|
|
else if (strcmp(p, "page") == 0)
|
|
|
|
popts->memctl_interleaving_mode =
|
|
|
|
FSL_DDR_PAGE_INTERLEAVING;
|
|
|
|
else if (strcmp(p, "bank") == 0)
|
|
|
|
popts->memctl_interleaving_mode =
|
|
|
|
FSL_DDR_BANK_INTERLEAVING;
|
|
|
|
else if (strcmp(p, "superbank") == 0)
|
|
|
|
popts->memctl_interleaving_mode =
|
|
|
|
FSL_DDR_SUPERBANK_INTERLEAVING;
|
|
|
|
else
|
|
|
|
popts->memctl_interleaving_mode =
|
|
|
|
simple_strtoul(p, NULL, 0);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
if( (p = getenv("ba_intlv_ctl")) != NULL) {
|
|
|
|
if (strcmp(p, "cs0_cs1") == 0)
|
|
|
|
popts->ba_intlv_ctl = FSL_DDR_CS0_CS1;
|
|
|
|
else if (strcmp(p, "cs2_cs3") == 0)
|
|
|
|
popts->ba_intlv_ctl = FSL_DDR_CS2_CS3;
|
|
|
|
else if (strcmp(p, "cs0_cs1_and_cs2_cs3") == 0)
|
|
|
|
popts->ba_intlv_ctl = FSL_DDR_CS0_CS1_AND_CS2_CS3;
|
|
|
|
else if (strcmp(p, "cs0_cs1_cs2_cs3") == 0)
|
|
|
|
popts->ba_intlv_ctl = FSL_DDR_CS0_CS1_CS2_CS3;
|
|
|
|
else
|
|
|
|
popts->ba_intlv_ctl = simple_strtoul(p, NULL, 0);
|
|
|
|
|
|
|
|
switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) {
|
|
|
|
case FSL_DDR_CS0_CS1_CS2_CS3:
|
|
|
|
case FSL_DDR_CS0_CS1:
|
|
|
|
if (pdimm[0].n_ranks != 2) {
|
|
|
|
popts->ba_intlv_ctl = 0;
|
|
|
|
printf("Not enough bank(chip-select) for "
|
|
|
|
"CS0+CS1, force non-interleaving!\n");
|
|
|
|
}
|
|
|
|
break;
|
|
|
|
case FSL_DDR_CS2_CS3:
|
|
|
|
if (pdimm[1].n_ranks !=2){
|
|
|
|
popts->ba_intlv_ctl = 0;
|
|
|
|
printf("Not enough bank(CS) for CS2+CS3, "
|
|
|
|
"force non-interleaving!\n");
|
|
|
|
}
|
|
|
|
break;
|
|
|
|
case FSL_DDR_CS0_CS1_AND_CS2_CS3:
|
|
|
|
if ((pdimm[0].n_ranks != 2)||(pdimm[1].n_ranks != 2)) {
|
|
|
|
popts->ba_intlv_ctl = 0;
|
|
|
|
printf("Not enough bank(CS) for CS0+CS1 or "
|
|
|
|
"CS2+CS3, force non-interleaving!\n");
|
|
|
|
}
|
|
|
|
break;
|
|
|
|
default:
|
|
|
|
popts->ba_intlv_ctl = 0;
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
fsl_ddr_board_options(popts, pdimm, ctrl_num);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|