upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
u-boot/doc/README.nand

177 lines
6.9 KiB

NAND FLASH commands and notes
# (C) Copyright 2003
# Dave Ellis, SIXNET, dge@sixnetio.com
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
Commands:
nand bad
Print a list of all of the bad blocks in the current device.
nand device
Print information about the current NAND device.
nand device num
Make device `num' the current device and print information about it.
nand erase off size
nand erase clean [off size]
Erase `size' bytes starting at offset `off'. Only complete erase
blocks can be erased.
If `clean' is specified, a JFFS2-style clean marker is written to
each block after it is erased. If `clean' is specified without an
offset or size, the entire flash is erased.
This command will not erase blocks that are marked bad. There is
a debug option in cmd_nand.c to allow bad blocks to be erased.
Please read the warning there before using it, as blocks marked
bad by the manufacturer must _NEVER_ be erased.
nand info
Print information about all of the NAND devices found.
nand read addr ofs size
Read `size' bytes from `ofs' in NAND flash to `addr'. If a page
cannot be read because it is marked bad or an uncorrectable data
error is found the command stops with an error.
nand read.jffs2 addr ofs size
Like `read', but the data for blocks that are marked bad is read as
0xff. This gives a readable JFFS2 image that can be processed by
the JFFS2 commands such as ls and fsload.
nand read.oob addr ofs size
Read `size' bytes from the out-of-band data area corresponding to
`ofs' in NAND flash to `addr'. This is limited to the 16 bytes of
data for one 512-byte page or 2 256-byte pages. There is no check
for bad blocks or ECC errors.
nand write addr ofs size
Write `size' bytes from `addr' to `ofs' in NAND flash. If a page
cannot be written because it is marked bad or the write fails the
command stops with an error.
nand write.jffs2 addr ofs size
Like `write', but blocks that are marked bad are skipped and the
is written to the next block instead. This allows writing writing
a JFFS2 image, as long as the image is short enough to fit even
after skipping the bad blocks. Compact images, such as those
produced by mkfs.jffs2 should work well, but loading an image copied
from another flash is going to be trouble if there are any bad blocks.
nand write.oob addr ofs size
Write `size' bytes from `addr' to the out-of-band data area
corresponding to `ofs' in NAND flash. This is limited to the 16 bytes
of data for one 512-byte page or 2 256-byte pages. There is no check
for bad blocks.
Configuration Options:
CFG_CMD_NAND
A good one to add to CONFIG_COMMANDS since it enables NAND support.
CONFIG_MTD_NAND_ECC_JFFS2
Define this if you want the Error Correction Code information in
the out-of-band data to be formatted to match the JFFS2 file system.
CONFIG_MTD_NAND_ECC_YAFFS would be another useful choice for
someone to implement.
CFG_MAX_NAND_DEVICE
The maximum number of NAND devices you want to support.
NAND Interface:
#define NAND_WAIT_READY(nand)
Wait until the NAND flash is ready. Typically this would be a
loop waiting for the READY/BUSY line from the flash to indicate it
it is ready.
#define WRITE_NAND_COMMAND(d, adr)
Write the command byte `d' to the flash at `adr' with the
CLE (command latch enable) line true. If your board uses writes to
different addresses to control CLE and ALE, you can modify `adr'
to be the appropriate address here. If your board uses I/O registers
to control them, it is probably better to let NAND_CTL_SETCLE()
and company do it.
#define WRITE_NAND_ADDRESS(d, adr)
Write the address byte `d' to the flash at `adr' with the
ALE (address latch enable) line true. If your board uses writes to
different addresses to control CLE and ALE, you can modify `adr'
to be the appropriate address here. If your board uses I/O registers
to control them, it is probably better to let NAND_CTL_SETALE()
and company do it.
#define WRITE_NAND(d, adr)
Write the data byte `d' to the flash at `adr' with the
ALE and CLE lines false. If your board uses writes to
different addresses to control CLE and ALE, you can modify `adr'
to be the appropriate address here. If your board uses I/O registers
to control them, it is probably better to let NAND_CTL_CLRALE()
and company do it.
#define READ_NAND(adr)
Read a data byte from the flash at `adr' with the
ALE and CLE lines false. If your board uses reads from
different addresses to control CLE and ALE, you can modify `adr'
to be the appropriate address here. If your board uses I/O registers
to control them, it is probably better to let NAND_CTL_CLRALE()
and company do it.
#define NAND_DISABLE_CE(nand)
Set CE (Chip Enable) low to enable the NAND flash.
#define NAND_ENABLE_CE(nand)
Set CE (Chip Enable) high to disable the NAND flash.
#define NAND_CTL_CLRALE(nandptr)
Set ALE (address latch enable) low. If ALE control is handled by
WRITE_NAND_ADDRESS() this can be empty.
#define NAND_CTL_SETALE(nandptr)
Set ALE (address latch enable) high. If ALE control is handled by
WRITE_NAND_ADDRESS() this can be empty.
#define NAND_CTL_CLRCLE(nandptr)
Set CLE (command latch enable) low. If CLE control is handled by
WRITE_NAND_ADDRESS() this can be empty.
#define NAND_CTL_SETCLE(nandptr)
Set CLE (command latch enable) high. If CLE control is handled by
WRITE_NAND_ADDRESS() this can be empty.
More Definitions:
These definitions are needed in the board configuration for now, but
may really belong in a header file.
TODO: Figure which ones are truly configuration settings and rename
them to CFG_NAND_... and move the rest somewhere appropriate.
#define SECTORSIZE 512
#define ADDR_COLUMN 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1