|
|
|
This is the readme for the Das U-Boot standalone program smc91111
|
|
|
|
|
|
|
|
The main purpose of this is to manage MAC addresses on platforms
|
|
|
|
which include the SMC91111 integrated 10/100 MAC Phy, with attached
|
|
|
|
EEPROMs.
|
|
|
|
|
|
|
|
|
|
|
|
Contents:
|
|
|
|
------------------------
|
|
|
|
1. Ensuring U-boot's MAC address can be set in hardware
|
|
|
|
2. Running the smc91111_eeprom program
|
|
|
|
3. Setting MAC addresses
|
|
|
|
4. Other things you can do with this
|
|
|
|
5. Things to be done.
|
|
|
|
|
|
|
|
|
|
|
|
1. Ensuring U-boot's MAC address can be set in hardware
|
|
|
|
--------------------------------------------------------------------------
|
|
|
|
|
|
|
|
On the Internet - MAC addresses are very important. Short for Media
|
|
|
|
Access Control address, a hardware address that uniquely identifies
|
|
|
|
each node of a network. When things are not unique - bad things
|
|
|
|
can happen. This is why U-Boot makes it difficult to change MAC
|
|
|
|
addresses.
|
|
|
|
|
|
|
|
To find out who has a MAC address, or to purchase MAC addresses, goto
|
|
|
|
the IEEE, at:
|
|
|
|
http://standards.ieee.org/regauth/oui/index.shtml
|
|
|
|
|
|
|
|
2. Running the smc91111_eeprom program
|
|
|
|
---------------------------------------------------------------------
|
|
|
|
|
|
|
|
After Uboot is compiled, there should be three files of interest:
|
|
|
|
-rwxr-xr-x 1 8806 2004-10-11 14:00 smc91111_eeprom <- ELF
|
|
|
|
-rwxr-xr-x 1 3440 2004-10-11 14:00 smc91111_eeprom.bin <- BIN
|
|
|
|
-rwxr-xr-x 1 9524 2004-10-11 14:00 smc91111_eeprom.srec <- SREC
|
|
|
|
|
|
|
|
if there is not, check the examples/Makefile, and ensure there is something
|
|
|
|
like for your architecture:
|
|
|
|
|
|
|
|
ifeq ($(ARCH),blackfin)
|
|
|
|
SREC += smc91111_eeprom.srec
|
|
|
|
BIN += smc91111_eeprom.bin smc91111_eeprom
|
|
|
|
endif
|
|
|
|
|
|
|
|
To load the files: there are two methods: a) serial or b) network. Since
|
|
|
|
it is not a good idea to start doing things on the network before the
|
|
|
|
MAC address is set, this example will do things over serial.
|
|
|
|
|
|
|
|
a) Loading the elf file via the serial port
|
|
|
|
--------------------------------------------
|
|
|
|
Loading the elf is very easy - just ensure that the location
|
|
|
|
you specify things to load as is not the load address specified
|
|
|
|
in the Makefile.
|
|
|
|
|
|
|
|
BOOT> loadb 0x1000000
|
|
|
|
|
|
|
|
## Ready for binary (kermit) download to 0x01000000 at 57600 bps...
|
|
|
|
|
|
|
|
(type CNTL-\ then C)
|
|
|
|
(Back at local machine)
|
|
|
|
----------------------------------------------------
|
|
|
|
Kermit>send ~/u-boot_1.1.1/examples/smc91111_eeprom
|
|
|
|
Kermit>connect
|
|
|
|
|
|
|
|
Connecting to /dev/ttyS0, speed 57600
|
|
|
|
Escape character: Ctrl-\ (ASCII 28, FS): enabled
|
|
|
|
Type the escape character followed by C to get back,
|
|
|
|
or followed by ? to see other options.
|
|
|
|
----------------------------------------------------
|
|
|
|
## Total Size = 0x00002266 = 8806 Bytes
|
|
|
|
## Start Addr = 0x01000000
|
|
|
|
|
|
|
|
BOOT> bootelf 0x1000000
|
|
|
|
|
|
|
|
Loading .text @ 0x00001000 (3440 bytes)
|
|
|
|
## Starting application at 0x000010d8 ...
|
|
|
|
|
|
|
|
SMC91111>
|
|
|
|
|
|
|
|
b) Loading the binary file via the serial port
|
|
|
|
-----------------------------------------------
|
|
|
|
For many toolchains, the entry point is not the load point.
|
|
|
|
The Load point is a hard coded address from the
|
|
|
|
examples/Makefile. The entry point can be found by doing something
|
|
|
|
like:
|
|
|
|
|
|
|
|
u-boot_1.1.1/examples> bfin-elf-objdump -d smc91111_eeprom |less
|
|
|
|
|
|
|
|
smc91111_eeprom: file format elf32-bfin
|
|
|
|
|
|
|
|
Disassembly of section .text:
|
|
|
|
|
|
|
|
00001000 <smc91111_eeprom-0xd8>:
|
|
|
|
1000:
|
|
|
|
000010d8 <smc91111_eeprom>:
|
|
|
|
|
|
|
|
You can see that the entry point (or the address that should be
|
|
|
|
jumped to is 0x10d8). This is also the same as the entry point
|
|
|
|
of the elf file.
|
|
|
|
|
|
|
|
Now we load it to the actual load location:
|
|
|
|
|
|
|
|
BOOT> loadb 0x1000
|
|
|
|
|
|
|
|
## Ready for binary (kermit) download to 0x00001000 at 57600 bps...
|
|
|
|
|
|
|
|
(Back at pinky.dsl-only.net)
|
|
|
|
----------------------------------------------------
|
|
|
|
Kermit>send /tftpboot/eeprom.bin
|
|
|
|
Kermit>connect
|
|
|
|
|
|
|
|
Connecting to /dev/ttyS0, speed 57600
|
|
|
|
Escape character: Ctrl-\ (ASCII 28, FS): enabled
|
|
|
|
Type the escape character followed by C to get back,
|
|
|
|
or followed by ? to see other options.
|
|
|
|
----------------------------------------------------
|
|
|
|
## Total Size = 0x00000d70 = 3440 Bytes
|
|
|
|
## Start Addr = 0x00001000
|
|
|
|
|
|
|
|
BOOT> go 0x10D8
|
|
|
|
|
|
|
|
## Starting application at 0x000010D8 ...
|
|
|
|
|
|
|
|
SMC91111>
|
|
|
|
|
|
|
|
3. Setting MAC addresses
|
|
|
|
--------------------------------------------------------------------------
|
|
|
|
|
|
|
|
The MAC address can be stored in four locations:
|
|
|
|
|
|
|
|
-Boot environmental variable in Flash <- can not change, without
|
|
|
|
re-flashing U-boot.
|
|
|
|
U-Boot environmental variable <- can not change, without
|
|
|
|
resetting board/U-Boot
|
|
|
|
LAN91C111 Registers <- volatile
|
|
|
|
LAN91C111 EEPROM <- Non-volatile
|
|
|
|
|
|
|
|
If you have not activated the network, and do not have a hardcoded
|
|
|
|
or pre-assigned MAC address in U-boot, the environmental variables
|
|
|
|
should be blank, and allow you to set things one time.
|
|
|
|
|
|
|
|
To set the EEPROM MAC address to 12:34:56:78:9A:BC
|
|
|
|
|
|
|
|
SMC91111> W E 20 3412
|
|
|
|
|
|
|
|
Writing EEPROM register 20 with 3412
|
|
|
|
SMC91111> W E 21 7856
|
|
|
|
|
|
|
|
Writing EEPROM register 21 with 7856
|
|
|
|
SMC91111> W E 22 BC9A
|
|
|
|
|
|
|
|
Writing EEPROM register 22 with bc9a
|
|
|
|
EEPROM contents copied to MAC
|
|
|
|
SMC91111> P
|
|
|
|
|
|
|
|
Current MAC Address in SMSC91111 12:34:56:78:9a:bc
|
|
|
|
Current MAC Address in EEPROM 12:34:56:78:9a:bc
|
|
|
|
|
|
|
|
(CNTRL-C to exit)
|
|
|
|
SMC91111> ## Application terminated, rc = 0x0
|
|
|
|
|
|
|
|
BOOT> reset
|
|
|
|
U-Boot 1.1.1 (gcc version: 3.3.3)
|
|
|
|
Release Version Beta released on Oct 10 2004 - 00:34:35
|
|
|
|
Blackfin support by LG Soft India
|
|
|
|
For further information please check this link http://www.blackfin.uclinux.org
|
|
|
|
BOOT> ping 192.168.0.4
|
|
|
|
|
|
|
|
Using MAC Address 12:34:56:78:9A:BC
|
|
|
|
host 192.168.0.4 is alive
|
|
|
|
|
|
|
|
|
|
|
|
4. Other things that you can do
|
|
|
|
--------------------------------------------------------------------------
|
|
|
|
After the stand alone application is running, there are a few options:
|
|
|
|
- P : Print the MAC
|
|
|
|
- D : Dump the LAN91C111 EEPROM contents
|
|
|
|
- M : Dump the LAN91C111 MAC contents
|
|
|
|
- C : Copies the MAC address from the EEPROM to the LAN91C111
|
|
|
|
- W : Write a register in the EEPROM or in the MAC
|
|
|
|
|
|
|
|
SMC91111> P
|
|
|
|
|
|
|
|
Current MAC Address in SMSC91111 12:34:56:78:9a:bc
|
|
|
|
Current MAC Address in EEPROM 12:34:56:78:9a:bc
|
|
|
|
|
|
|
|
SMC91111> D
|
|
|
|
|
|
|
|
IOS2-0 000 001 002 003 004 005 006 007
|
|
|
|
CONFIG 00:ffff 04:ffff 08:ffff 0c:ffff 10:ffff 14:ffff 18:ffff 1c:ffff
|
|
|
|
BASE 01:ffff 05:ffff 09:ffff 0d:ffff 11:ffff 15:ffff 19:ffff 1d:ffff
|
|
|
|
02:ffff 06:ffff 0a:ffff 0e:0020 12:ffff 16:ffff 1a:ffff 1e:ffff
|
|
|
|
03:ffff 07:ffff 0b:ffff 0f:ffff 13:ffff 17:ffff 1b:ffff 1f:ffff
|
|
|
|
|
|
|
|
20:3412 21:7856 22:bc9a 23:ffff 24:ffff 25:ffff 26:ffff 27:ffff
|
|
|
|
28:ffff 29:ffff 2a:ffff 2b:ffff 2c:ffff 2d:ffff 2e:ffff 2f:ffff
|
|
|
|
30:ffff 31:ffff 32:ffff 33:ffff 34:ffff 35:ffff 36:ffff 37:ffff
|
|
|
|
38:ffff 39:ffff 3a:ffff 3b:ffff 3c:ffff 3d:ffff 3e:ffff 3f:ffff
|
|
|
|
|
|
|
|
SMC91111> M
|
|
|
|
|
|
|
|
Bank0 Bank1 Bank2 Bank3
|
|
|
|
00 0000 a0b1 3332 0000
|
|
|
|
02 0000 1801 8000 0000
|
|
|
|
04 0000 3412 8080 0000
|
|
|
|
06 0000 7856 003f 0000
|
|
|
|
08 0404 bc9a 02df 3332
|
|
|
|
0a 0000 ffff 02df 3391
|
|
|
|
0c 0000 1214 0004 001f
|
|
|
|
0e 3300 3301 3302 3303
|
|
|
|
|
|
|
|
SMC91111> C
|
|
|
|
|
|
|
|
EEPROM contents copied to MAC
|
|
|
|
|
|
|
|
SMC91111> W E 2A ABCD
|
|
|
|
|
|
|
|
Writing EEPROM register 2a with abcd
|
|
|
|
|
|
|
|
SMC91111> W M 14 FF00
|
|
|
|
|
|
|
|
Writing MAC register bank 1, reg 04 with ff00
|