|
|
|
|
Overview
|
|
|
|
|
=========
|
|
|
|
|
The P1010RDB-PB is a Freescale Reference Design Board that hosts the P1010 SoC.
|
|
|
|
|
P1010RDB-PB is a variation of previous P1010RDB-PA board.
|
|
|
|
|
|
|
|
|
|
The P1010 is a cost-effective, low-power, highly integrated host processor
|
|
|
|
|
based on a Power Architecture e500v2 core (maximum core frequency 1GHz),that
|
|
|
|
|
addresses the requirements of several routing, gateways, storage, consumer,
|
|
|
|
|
and industrial applications. Applications of interest include the main CPUs and
|
|
|
|
|
I/O processors in network attached storage (NAS), the voice over IP (VoIP)
|
|
|
|
|
router/gateway, and wireless LAN (WLAN) and industrial controllers.
|
|
|
|
|
|
|
|
|
|
The P1010RDB-PB board features are as following:
|
|
|
|
|
Memory subsystem:
|
|
|
|
|
- 1G bytes unbuffered DDR3 SDRAM discrete devices (32-bit bus)
|
|
|
|
|
- 32M bytes NOR flash single-chip memory
|
|
|
|
|
- 2G bytes NAND flash memory
|
|
|
|
|
- 16M bytes SPI memory
|
|
|
|
|
- 256K bit M24256 I2C EEPROM
|
|
|
|
|
- I2C Board EEPROM 128x8 bit memory
|
|
|
|
|
- SD/MMC connector to interface with the SD memory card
|
|
|
|
|
Interfaces:
|
|
|
|
|
- Three 10/100/1000 BaseT Ethernet ports (One RGMII and two SGMII)
|
|
|
|
|
- PCIe 2.0: two x1 mini-PCIe slots
|
|
|
|
|
- SATA 2.0: two SATA interfaces
|
|
|
|
|
- USB 2.0: one USB interface
|
|
|
|
|
- FlexCAN: two FlexCAN interfaces (revision 2.0B)
|
|
|
|
|
- UART: one USB-to-Serial interface
|
|
|
|
|
- TDM: 2 FXS ports connected via an external SLIC to the TDM interface.
|
|
|
|
|
1 FXO port connected via a relay to FXS for switchover to POTS
|
|
|
|
|
|
|
|
|
|
Board connectors:
|
|
|
|
|
- Mini-ITX power supply connector
|
|
|
|
|
- JTAG/COP for debugging
|
|
|
|
|
|
|
|
|
|
POR: support critical POR setting changed via switch on board
|
|
|
|
|
PCB: 6-layer routing (4-layer signals, 2-layer power and ground)
|
|
|
|
|
|
|
|
|
|
Physical Memory Map on P1010RDB
|
|
|
|
|
===============================
|
|
|
|
|
Address Start Address End Memory type Attributes
|
|
|
|
|
0x0000_0000 0x3fff_ffff DDR 1G Cacheable
|
|
|
|
|
0xa000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable
|
|
|
|
|
0xee00_0000 0xefff_ffff NOR Flash 32M non-cacheable
|
|
|
|
|
0xffc2_0000 0xffc5_ffff PCI IO range 256K non-cacheable
|
|
|
|
|
0xffa0_0000 0xffaf_ffff NAND Flash 1M cacheable
|
|
|
|
|
0xffb0_0000 0xffbf_ffff Board CPLD 1M non-cacheable
|
|
|
|
|
0xffd0_0000 0xffd0_3fff L1 for Stack 16K Cacheable TLB0
|
|
|
|
|
0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Serial Port Configuration on P1010RDB
|
|
|
|
|
=====================================
|
|
|
|
|
Configure the serial port of the attached computer with the following values:
|
|
|
|
|
-Data rate: 115200 bps
|
|
|
|
|
-Number of data bits: 8
|
|
|
|
|
-Parity: None
|
|
|
|
|
-Number of Stop bits: 1
|
|
|
|
|
-Flow Control: Hardware/None
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P1010RDB-PB default DIP-switch settings
|
|
|
|
|
=======================================
|
|
|
|
|
SW1[1:8]= 10101010
|
|
|
|
|
SW2[1:8]= 11011000
|
|
|
|
|
SW3[1:8]= 10010000
|
|
|
|
|
SW4[1:4]= 1010
|
|
|
|
|
SW5[1:8]= 11111010
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P1010RDB-PB boot mode settings via DIP-switch
|
|
|
|
|
=============================================
|
|
|
|
|
SW4[1:4]= 1111 and SW3[3:4]= 00 for 16bit NOR boot
|
|
|
|
|
SW4[1:4]= 1010 and SW3[3:4]= 01 for 8bit NAND boot
|
|
|
|
|
SW4[1:4]= 0110 and SW3[3:4]= 00 for SPI boot
|
|
|
|
|
SW4[1:4]= 0111 and SW3[3:4]= 10 for SD boot
|
|
|
|
|
Note: 1 stands for 'on', 0 stands for 'off'
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Switch P1010RDB-PB boot mode via software without setting DIP-switch
|
|
|
|
|
====================================================================
|
|
|
|
|
=> run boot_bank0 (boot from NOR bank0)
|
|
|
|
|
=> run boot_bank1 (boot from NOR bank1)
|
|
|
|
|
=> run boot_nand (boot from NAND flash)
|
|
|
|
|
=> run boot_spi (boot from SPI flash)
|
|
|
|
|
=> run boot_sd (boot from SD card)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Frequency combination support on P1010RDB-PB
|
|
|
|
|
=============================================
|
|
|
|
|
SW1[4:7] SW5[1] SW5[5:8] SW2[2] Core(MHz) Platform(MHz) DDR(MT/s)
|
|
|
|
|
0101 1 1010 0 800 400 800
|
|
|
|
|
1001 1 1010 0 800 400 667
|
|
|
|
|
1010 1 1100 0 667 333 667
|
|
|
|
|
1000 0 1010 0 533 266 667
|
|
|
|
|
0101 1 1010 1 1000 400 800
|
|
|
|
|
1001 1 1010 1 1000 400 667
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Setting of pin mux
|
|
|
|
|
==================
|
|
|
|
|
Since pins multiplexing, TDM and CAN are muxed with SPI flash.
|
|
|
|
|
SDHC is muxed with IFC. IFC and SPI flash are enabled by default.
|
|
|
|
|
|
|
|
|
|
To enable TDM:
|
|
|
|
|
=> setenv hwconfig fsl_p1010mux:tdm_can=tdm
|
|
|
|
|
=> save;reset
|
|
|
|
|
|
|
|
|
|
To enable FlexCAN:
|
|
|
|
|
=> setenv hwconfig fsl_p1010mux:tdm_can=can
|
|
|
|
|
=> save;reset
|
|
|
|
|
|
|
|
|
|
To enable SDHC in case of NOR/NAND/SPI boot
|
|
|
|
|
a) For temporary use case in runtime without reboot system
|
|
|
|
|
run 'mux sdhc' in U-Boot to validate SDHC with invalidating IFC.
|
|
|
|
|
|
|
|
|
|
b) For long-term use case
|
|
|
|
|
set 'esdhc' in hwconfig and save it.
|
|
|
|
|
|
|
|
|
|
To enable IFC in case of SD boot
|
|
|
|
|
a) For temporary use case in runtime without reboot system
|
|
|
|
|
run 'mux ifc' in U-Boot to validate IFC with invalidating SDHC.
|
|
|
|
|
|
|
|
|
|
b) For long-term use case
|
|
|
|
|
set 'ifc' in hwconfig and save it.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Build images for different boot mode
|
|
|
|
|
====================================
|
|
|
|
|
First setup cross compile environment on build host
|
|
|
|
|
$ export ARCH=powerpc
|
|
|
|
|
$ export CROSS_COMPILE=<your-compiler-path>/powerpc-linux-gnu-
|
|
|
|
|
|
|
|
|
|
1. For NOR boot
|
|
|
|
|
$ make P1010RDB-PB_NOR
|
|
|
|
|
|
|
|
|
|
2. For NAND boot
|
|
|
|
|
$ make P1010RDB-PB_NAND
|
|
|
|
|
|
|
|
|
|
3. For SPI boot
|
|
|
|
|
$ make P1010RDB-PB_SPIFLASH
|
|
|
|
|
|
|
|
|
|
4. For SD boot
|
|
|
|
|
$ make P1010RDB-PB_SDCARD
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Steps to program images to flash for different boot mode
|
|
|
|
|
========================================================
|
|
|
|
|
1. NOR boot
|
|
|
|
|
=> tftp 1000000 u-boot.bin
|
|
|
|
|
For bank0
|
|
|
|
|
=> pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
|
|
|
|
|
set SW1[8]=0, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board
|
|
|
|
|
|
|
|
|
|
For bank1
|
|
|
|
|
=> pro off all;era eef40000 eeffffff;cp.b 1000000 eef40000 $filesize
|
|
|
|
|
set SW1[8]=1, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board
|
|
|
|
|
|
|
|
|
|
2. NAND boot
|
|
|
|
|
=> tftp 1000000 u-boot-nand.bin
|
|
|
|
|
=> nand erase 0 $filesize; nand write $loadaddr 0 $filesize
|
|
|
|
|
Set SW4[1:4]= 1010 and SW3[3:4]= 01, then power on the board
|
|
|
|
|
|
|
|
|
|
3. SPI boot
|
|
|
|
|
1) cat p1010rdb-config-header.bin u-boot.bin > u-boot-spi-combined.bin
|
|
|
|
|
2) => tftp 1000000 u-boot-spi-combined.bin
|
|
|
|
|
3) => sf probe 0; sf erase 0 100000; sf write 1000000 0 100000
|
|
|
|
|
set SW4[1:4]= 0110 and SW3[3:4]= 00, then power on the board
|
|
|
|
|
|
|
|
|
|
4. SD boot
|
|
|
|
|
1) cat p1010rdb-config-header.bin u-boot.bin > u-boot-sd-combined.bin
|
|
|
|
|
2) => tftp 1000000 u-boot-sd-combined.bin
|
|
|
|
|
3) => mux sdhc
|
|
|
|
|
4) => mmc write 1000000 0 1050
|
|
|
|
|
set SW4[1:4]= 0111 and SW3[3:4]= 10, then power on the board
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Boot Linux from network using TFTP on P1010RDB-PB
|
|
|
|
|
=================================================
|
|
|
|
|
Place uImage, p1010rdb.dtb and rootfs files in the TFTP download path.
|
|
|
|
|
=> tftp 1000000 uImage
|
|
|
|
|
=> tftp 2000000 p1010rdb.dtb
|
|
|
|
|
=> tftp 3000000 rootfs.ext2.gz.uboot.p1010rdb
|
|
|
|
|
=> bootm 1000000 3000000 2000000
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For more details, please refer to P1010RDB-PB User Guide and access website
|
|
|
|
|
www.freescale.com and Freescale QorIQ SDK Infocenter document.
|
