|
|
|
|
/*
|
|
|
|
|
* (C) Copyright 2010
|
|
|
|
|
* Marvell Semiconductor <www.marvell.com>
|
|
|
|
|
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>,
|
|
|
|
|
*
|
|
|
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#include <common.h>
|
|
|
|
|
#include <asm/io.h>
|
|
|
|
|
#include <mvmfp.h>
|
|
|
|
|
#include <asm/arch/mfp.h>
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* mfp_config
|
|
|
|
|
*
|
|
|
|
|
* On most of Marvell SoCs (ex. ARMADA100) there is Multi-Funtion-Pin
|
|
|
|
|
* configuration registers to configure each GPIO/Function pin on the
|
|
|
|
|
* SoC.
|
|
|
|
|
*
|
|
|
|
|
* This function reads the array of values for
|
|
|
|
|
* MFPR_X registers and programms them into respective
|
|
|
|
|
* Multi-Function Pin registers.
|
|
|
|
|
* It supports - Alternate Function Selection programming.
|
|
|
|
|
*
|
|
|
|
|
* Whereas,
|
|
|
|
|
* The Configureation value is constructed using MFP()
|
|
|
|
|
* array consists of 32bit values as defined in MFP(xx,xx..) macro
|
|
|
|
|
*/
|
|
|
|
|
void mfp_config(u32 *mfp_cfgs)
|
|
|
|
|
{
|
|
|
|
|
u32 *p_mfpr = NULL;
|
|
|
|
|
u32 cfg_val, val;
|
|
|
|
|
|
|
|
|
|
do {
|
|
|
|
|
cfg_val = *mfp_cfgs++;
|
|
|
|
|
/* exit if End of configuration table detected */
|
|
|
|
|
if (cfg_val == MFP_EOC)
|
|
|
|
|
break;
|
|
|
|
|
|
|
|
|
|
p_mfpr = (u32 *)(MV_MFPR_BASE
|
|
|
|
|
+ MFP_REG_GET_OFFSET(cfg_val));
|
|
|
|
|
|
|
|
|
|
/* Write a mfg register as per configuration */
|
|
|
|
|
val = 0;
|
|
|
|
|
if (cfg_val & MFP_VALUE_MASK)
|
|
|
|
|
val |= cfg_val & MFP_VALUE_MASK;
|
|
|
|
|
|
|
|
|
|
writel(val, p_mfpr);
|
|
|
|
|
} while (1);
|
|
|
|
|
/*
|
|
|
|
|
* perform a read-back of any MFPR register to make sure the
|
|
|
|
|
* previous writings are finished
|
|
|
|
|
*/
|
|
|
|
|
readl(p_mfpr);
|
|
|
|
|
}
|
