upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
u-boot/common/cmd_mmc_spi.c

90 lines
2.1 KiB

/*
* Command for mmc_spi setup.
*
* Copyright (C) 2010 Thomas Chou <thomas@wytron.com.tw>
* Licensed under the GPL-2 or later.
*/
#include <common.h>
#include <mmc.h>
#include <spi.h>
#ifndef CONFIG_MMC_SPI_BUS
# define CONFIG_MMC_SPI_BUS 0
#endif
#ifndef CONFIG_MMC_SPI_CS
# define CONFIG_MMC_SPI_CS 1
#endif
/* in SPI mode, MMC speed limit is 20MHz, while SD speed limit is 25MHz */
#ifndef CONFIG_MMC_SPI_SPEED
# define CONFIG_MMC_SPI_SPEED 25000000
#endif
/* MMC and SD specs only seem to care that sampling is on the
* rising edge ... meaning SPI modes 0 or 3. So either SPI mode
* should be legit. We'll use mode 0 since the steady state is 0,
* which is appropriate for hotplugging, unless the platform data
* specify mode 3 (if hardware is not compatible to mode 0).
*/
#ifndef CONFIG_MMC_SPI_MODE
# define CONFIG_MMC_SPI_MODE SPI_MODE_0
#endif
static int do_mmc_spi(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
uint bus = CONFIG_MMC_SPI_BUS;
uint cs = CONFIG_MMC_SPI_CS;
uint speed = CONFIG_MMC_SPI_SPEED;
uint mode = CONFIG_MMC_SPI_MODE;
char *endp;
struct mmc *mmc;
if (argc < 2)
goto usage;
cs = simple_strtoul(argv[1], &endp, 0);
if (*argv[1] == 0 || (*endp != 0 && *endp != ':'))
goto usage;
if (*endp == ':') {
if (endp[1] == 0)
goto usage;
bus = cs;
cs = simple_strtoul(endp + 1, &endp, 0);
if (*endp != 0)
goto usage;
}
if (argc >= 3) {
speed = simple_strtoul(argv[2], &endp, 0);
if (*argv[2] == 0 || *endp != 0)
goto usage;
}
if (argc >= 4) {
mode = simple_strtoul(argv[3], &endp, 16);
if (*argv[3] == 0 || *endp != 0)
goto usage;
}
if (!spi_cs_is_valid(bus, cs)) {
printf("Invalid SPI bus %u cs %u\n", bus, cs);
return 1;
}
mmc = mmc_spi_init(bus, cs, speed, mode);
if (!mmc) {
printf("Failed to create MMC Device\n");
return 1;
}
printf("%s: %d at %u:%u hz %u mode %u\n", mmc->name, mmc->block_dev.dev,
bus, cs, speed, mode);
mmc_init(mmc);
return 0;
usage:
cmd_usage(cmdtp);
return 1;
}
U_BOOT_CMD(
mmc_spi, 4, 0, do_mmc_spi,
"mmc_spi setup",
"[bus:]cs [hz] [mode] - setup mmc_spi device"
);