Whitebox
/
u-boot
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

board/t1024qds: add retimer support on t1024qds

Browse Source 
Initialize retimer for XFI on t1024qds.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
master
Shengzhou Liu 10 years ago committed by York Sun
parent 5818643bf4
commit 10227aaa24
2 changed files with 61 additions and 1 deletions
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Show Stats Download Patch File Download Diff File
  1. 57
      board/freescale/t102xqds/t102xqds.c
  2. 5
      include/configs/T102xQDS.h

57
board/freescale/t102xqds/t102xqds.c
Unescape View File

@ -186,6 +186,62 @@ static void board_mux_setup(void)
}
#endif
void board_retimer_ds125df111_init(void)
{
u8 reg;
/* Retimer DS125DF111 is connected to I2C1_CH7_CH5 */
reg = I2C_MUX_CH7;
i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &reg, 1);
reg = I2C_MUX_CH5;
i2c_write(I2C_MUX_PCA_ADDR_SEC, 0, 1, &reg, 1);
/* Access to Control/Shared register */
reg = 0x0;
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, &reg, 1);
/* Read device revision and ID */
i2c_read(I2C_RETIMER_ADDR, 1, 1, &reg, 1);
debug("Retimer version id = 0x%x\n", reg);
/* Enable Broadcast */
reg = 0x0c;
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, &reg, 1);
/* Reset Channel Registers */
i2c_read(I2C_RETIMER_ADDR, 0, 1, &reg, 1);
reg |= 0x4;
i2c_write(I2C_RETIMER_ADDR, 0, 1, &reg, 1);
/* Enable override divider select and Enable Override Output Mux */
i2c_read(I2C_RETIMER_ADDR, 9, 1, &reg, 1);
reg |= 0x24;
i2c_write(I2C_RETIMER_ADDR, 9, 1, &reg, 1);
/* Select VCO Divider to full rate (000) */
i2c_read(I2C_RETIMER_ADDR, 0x18, 1, &reg, 1);
reg &= 0x8f;
i2c_write(I2C_RETIMER_ADDR, 0x18, 1, &reg, 1);
/* Select active PFD MUX input as re-timed data (001) */
i2c_read(I2C_RETIMER_ADDR, 0x1e, 1, &reg, 1);
reg &= 0x3f;
reg |= 0x20;
i2c_write(I2C_RETIMER_ADDR, 0x1e, 1, &reg, 1);
/* Set data rate as 10.3125 Gbps */
reg = 0x0;
i2c_write(I2C_RETIMER_ADDR, 0x60, 1, &reg, 1);
reg = 0xb2;
i2c_write(I2C_RETIMER_ADDR, 0x61, 1, &reg, 1);
reg = 0x90;
i2c_write(I2C_RETIMER_ADDR, 0x62, 1, &reg, 1);
reg = 0xb3;
i2c_write(I2C_RETIMER_ADDR, 0x63, 1, &reg, 1);
reg = 0xcd;
i2c_write(I2C_RETIMER_ADDR, 0x64, 1, &reg, 1);
}
int board_early_init_r(void)
{
#ifdef CONFIG_SYS_FLASH_BASE
@ -220,6 +276,7 @@ int board_early_init_r(void)
#endif
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
board_mux_lane_to_slot();
board_retimer_ds125df111_init();
/* Increase IO drive strength to address FCS error on RGMII */
out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR, 0xbfdb7800);

5
include/configs/T102xQDS.h
Unescape View File

@ -555,11 +555,14 @@ unsigned long get_board_ddr_clk(void);
#define I2C_MUX_PCA_ADDR 0x77
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
#define I2C_RETIMER_ADDR 0x18
/* I2C bus multiplexer */
#define I2C_MUX_CH_DEFAULT 0x8
#define I2C_MUX_CH_DIU 0xC
#define I2C_MUX_CH5 0xD
#define I2C_MUX_CH7 0xF
/* LDI/DVI Encoder for display */
#define CONFIG_SYS_I2C_LDI_ADDR 0x38

Write Preview
Loading…
Cancel
Save