Whitebox
/
u-boot
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

powerpc/p2041: configure the CPLD lane_mux according to RCW

Browse Source 
Lane muxing on p2041 is controlled by a reg in CPLD, offset of this reg
is 0xc, CPLD supports SATA by default, we should re-configure the lane
muxing according to RCW, which indicates what SerDes protocol it is running.

Default lane muxing map is as below:
Lane G on bank1 routes to SGMII, controlled by bit 1 of the reg;
Lane A on bank2 routes to AURORA, controlled by bit 0 of the reg;
Lane C/D on bank2 routes to SATA0 and SATA1, controlled by bit 2
and bit 3 respectively.

Default value of these bits for lane muxing is '1', we should set or clear
these bits accoring to RCW.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
master
Shaohui Xie 12 years ago committed by Andy Fleming
parent 98de369b1c
commit 145dbc0250
1 changed files with 39 additions and 0 deletions
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Show Stats Download Patch File Download Diff File
  1. 39
      board/freescale/p2041rdb/eth.c

39
board/freescale/p2041rdb/eth.c
Unescape View File

@ -136,6 +136,11 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
}
#endif /* #ifdef CONFIG_FMAN_ENET */
#define CPLD_LANE_A_SEL 0x1
#define CPLD_LANE_G_SEL 0x2
#define CPLD_LANE_C_SEL 0x4
#define CPLD_LANE_D_SEL 0x8
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_FMAN_ENET
@ -143,6 +148,10 @@ int board_eth_init(bd_t *bis)
struct tgec_mdio_info tgec_mdio_info;
unsigned int i, slot;
int lane;
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
int srds_prtcl = (in_be32(&gur->rcwsr[4]) &
FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26;
u8 mux = CPLD_READ(serdes_mux);
printf("Initializing Fman\n");
@ -172,6 +181,36 @@ int board_eth_init(bd_t *bis)
fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC3, CONFIG_SYS_FM1_DTSEC3_PHY_ADDR);
mux &= ~(CPLD_LANE_A_SEL | CPLD_LANE_C_SEL | CPLD_LANE_D_SEL);
switch (srds_prtcl) {
case 0x2:
case 0xf:
mux &= ~CPLD_LANE_G_SEL;
break;
case 0x5:
case 0x9:
case 0xa:
case 0x17:
mux |= CPLD_LANE_G_SEL;
break;
case 0x14:
mux = (mux & (~CPLD_LANE_G_SEL)) | CPLD_LANE_A_SEL;
break;
case 0x8:
case 0x16:
case 0x19:
case 0x1a:
mux |= CPLD_LANE_G_SEL | CPLD_LANE_C_SEL | CPLD_LANE_D_SEL;
break;
case 0x1c:
mux |= CPLD_LANE_G_SEL | CPLD_LANE_A_SEL;
break;
default:
printf("Fman:Unsupported SerDes Protocol 0x%02x\n", srds_prtcl);
break;
}
CPLD_WRITE(serdes_mux, mux);
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
int idx = i - FM1_DTSEC1;

Write Preview
Loading…
Cancel
Save