diff --git a/MAINTAINERS b/MAINTAINERS
index ef53a79..fcc2043 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -263,6 +263,10 @@ Jon Loeliger <jdl@freescale.com>
 
 	MPC8641HPCN	MPC8641D
 
+Ron Madrid <info@sheldoninst.com>
+
+	SIMPC8313	MPC8313
+
 Dan Malek <dan@embeddedalley.com>
 
 	stxgp3		MPC85xx
diff --git a/MAKEALL b/MAKEALL
index 0733dfc..29faaa5 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -353,6 +353,7 @@ LIST_83xx="		\
 	MPC837XERDB	\
 	MVBLM7		\
 	sbc8349		\
+	SIMPC8313_LP	\
 	TQM834x		\
 "
 
diff --git a/Makefile b/Makefile
index 121e096..4aeae07 100644
--- a/Makefile
+++ b/Makefile
@@ -2328,6 +2328,21 @@ MVBLM7_config: unconfig
 sbc8349_config:		unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349
 
+SIMPC8313_LP_config \
+SIMPC8313_SP_config: unconfig
+	@mkdir -p $(obj)include
+	@mkdir -p $(obj)board/sheldon/simpc8313
+	@if [ "$(findstring _LP_,$@)" ] ; then \
+		$(XECHO) -n "...Large Page NAND..." ; \
+		echo "#define CONFIG_NAND_LP" >> $(obj)include/config.h ; \
+	fi ; \
+	if [ "$(findstring _SP_,$@)" ] ; then \
+		$(XECHO) -n "...Small Page NAND..." ; \
+		echo "#define CONFIG_NAND_SP" >> $(obj)include/config.h ; \
+	fi ;
+	@$(MKCONFIG) -a SIMPC8313 ppc mpc83xx simpc8313 sheldon
+	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+
 TQM834x_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc83xx tqm834x tqc
 
diff --git a/board/freescale/mpc8315erdb/mpc8315erdb.c b/board/freescale/mpc8315erdb/mpc8315erdb.c
index ea4b04f..f80b0ba 100644
--- a/board/freescale/mpc8315erdb/mpc8315erdb.c
+++ b/board/freescale/mpc8315erdb/mpc8315erdb.c
@@ -30,6 +30,7 @@
 #include <pci.h>
 #include <mpc83xx.h>
 #include <netdev.h>
+#include <asm/io.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -95,12 +96,45 @@ static struct pci_region pci_regions[] = {
 	}
 };
 
+static struct pci_region pcie_regions_0[] = {
+	{
+		.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+		.size = CONFIG_SYS_PCIE1_MEM_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+		.size = CONFIG_SYS_PCIE1_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
+static struct pci_region pcie_regions_1[] = {
+	{
+		.bus_start = CONFIG_SYS_PCIE2_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCIE2_MEM_PHYS,
+		.size = CONFIG_SYS_PCIE2_MEM_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CONFIG_SYS_PCIE2_IO_BASE,
+		.phys_start = CONFIG_SYS_PCIE2_IO_PHYS,
+		.size = CONFIG_SYS_PCIE2_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
 void pci_init_board(void)
 {
 	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile sysconf83xx_t *sysconf = &immr->sysconf;
 	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
 	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	volatile law83xx_t *pcie_law = sysconf->pcielaw;
 	struct pci_region *reg[] = { pci_regions };
+	struct pci_region *pcie_reg[] = { pcie_regions_0, pcie_regions_1, };
 	int warmboot;
 
 	/* Enable all 3 PCI_CLK_OUTPUTs. */
@@ -119,6 +153,24 @@ void pci_init_board(void)
 	warmboot |= immr->pmc.pmccr1 & PMCCR1_POWER_OFF;
 
 	mpc83xx_pci_init(1, reg, warmboot);
+
+	/* Configure the clock for PCIE controller */
+	clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM | SCCR_PCIEXP2CM,
+				    SCCR_PCIEXP1CM_1 | SCCR_PCIEXP2CM_1);
+
+	/* Deassert the resets in the control register */
+	out_be32(&sysconf->pecr1, 0xE0008000);
+	out_be32(&sysconf->pecr2, 0xE0008000);
+	udelay(2000);
+
+	/* Configure PCI Express Local Access Windows */
+	out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+	out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	out_be32(&pcie_law[1].bar, CONFIG_SYS_PCIE2_BASE & LAWBAR_BAR);
+	out_be32(&pcie_law[1].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	mpc83xx_pcie_init(2, pcie_reg, warmboot);
 }
 
 #if defined(CONFIG_OF_BOARD_SETUP)
diff --git a/board/freescale/mpc8349emds/pci.c b/board/freescale/mpc8349emds/pci.c
index ad7bf5d..af0b1da 100644
--- a/board/freescale/mpc8349emds/pci.c
+++ b/board/freescale/mpc8349emds/pci.c
@@ -171,15 +171,10 @@ void pci_init_board(void)
 void pci_init_board(void)
 {
 	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
-	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
 	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
 	volatile pcictrl83xx_t *pci_ctrl = &immr->pci_ctrl[0];
 	struct pci_region *reg[] = { pci1_regions };
 
-	/* Enable all 8 PCI_CLK_OUTPUTS */
-	clk->occr = 0xff000000;
-	udelay(2000);
-
 	/* Configure PCI Local Access Windows */
 	pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
 	pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G;
@@ -187,8 +182,6 @@ void pci_init_board(void)
 	pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
 	pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_4M;
 
-	udelay(2000);
-
 	mpc83xx_pci_init(1, reg, 0);
 
 	/* Configure PCI Inbound Translation Windows (3 1MB windows) */
diff --git a/board/freescale/mpc837xemds/mpc837xemds.c b/board/freescale/mpc837xemds/mpc837xemds.c
index acf8ada..156d808 100644
--- a/board/freescale/mpc837xemds/mpc837xemds.c
+++ b/board/freescale/mpc837xemds/mpc837xemds.c
@@ -18,6 +18,7 @@
 #include <tsec.h>
 #include <libfdt.h>
 #include <fdt_support.h>
+#include "pci.h"
 #include "../common/pq-mds-pib.h"
 
 int board_early_init_f(void)
@@ -38,14 +39,10 @@ int board_early_init_f(void)
 	case SPR_8377:
 		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
 				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
-		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
-				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
 		break;
 	case SPR_8378:
 		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SGMII,
 				 FSL_SERDES_CLK_125, FSL_SERDES_VDD_1V);
-		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
-				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
 		break;
 	case SPR_8379:
 		fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
@@ -316,6 +313,7 @@ void ft_board_setup(void *blob, bd_t *bd)
 	ft_pci_setup(blob, bd);
 	if (board_pci_host_broken())
 		ft_pci_fixup(blob, bd);
+	ft_pcie_fixup(blob, bd);
 #endif
 }
 #endif /* CONFIG_OF_BOARD_SETUP */
diff --git a/board/freescale/mpc837xemds/pci.c b/board/freescale/mpc837xemds/pci.c
index df4e748..31116b3 100644
--- a/board/freescale/mpc837xemds/pci.c
+++ b/board/freescale/mpc837xemds/pci.c
@@ -16,7 +16,9 @@
 #include <mpc83xx.h>
 #include <pci.h>
 #include <i2c.h>
+#include <fdt_support.h>
 #include <asm/fsl_i2c.h>
+#include <asm/fsl_serdes.h>
 
 #if defined(CONFIG_PCI)
 static struct pci_region pci_regions[] = {
@@ -40,15 +42,59 @@ static struct pci_region pci_regions[] = {
 	}
 };
 
+static struct pci_region pcie_regions_0[] = {
+	{
+		.bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+		.size = CONFIG_SYS_PCIE1_MEM_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+		.phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+		.size = CONFIG_SYS_PCIE1_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
+static struct pci_region pcie_regions_1[] = {
+	{
+		.bus_start = CONFIG_SYS_PCIE2_MEM_BASE,
+		.phys_start = CONFIG_SYS_PCIE2_MEM_PHYS,
+		.size = CONFIG_SYS_PCIE2_MEM_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CONFIG_SYS_PCIE2_IO_BASE,
+		.phys_start = CONFIG_SYS_PCIE2_IO_PHYS,
+		.size = CONFIG_SYS_PCIE2_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
+static int is_pex_x2(void)
+{
+	const char *pex_x2 = getenv("pex_x2");
+
+	if (pex_x2 && !strcmp(pex_x2, "yes"))
+		return 1;
+	return 0;
+}
+
 void pci_init_board(void)
 {
 	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile sysconf83xx_t *sysconf = &immr->sysconf;
 	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
 	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	volatile law83xx_t *pcie_law = sysconf->pcielaw;
 	struct pci_region *reg[] = { pci_regions };
+	struct pci_region *pcie_reg[] = { pcie_regions_0, pcie_regions_1, };
+	u32 spridr = in_be32(&immr->sysconf.spridr);
+	int pex2 = is_pex_x2();
 
 	if (board_pci_host_broken())
-		return;
+		goto skip_pci;
 
 	/* Enable all 5 PCI_CLK_OUTPUTS */
 	clk->occr |= 0xf8000000;
@@ -64,5 +110,46 @@ void pci_init_board(void)
 	udelay(2000);
 
 	mpc83xx_pci_init(1, reg, 0);
+skip_pci:
+	/* There is no PEX in MPC8379 parts. */
+	if (PARTID_NO_E(spridr) == SPR_8379)
+		return;
+
+	/* Configure the clock for PCIE controller */
+	clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM | SCCR_PCIEXP2CM,
+				    SCCR_PCIEXP1CM_1 | SCCR_PCIEXP2CM_1);
+
+	/* Deassert the resets in the control register */
+	out_be32(&sysconf->pecr1, 0xE0008000);
+	if (!pex2)
+		out_be32(&sysconf->pecr2, 0xE0008000);
+	udelay(2000);
+
+	/* Configure PCI Express Local Access Windows */
+	out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+	out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	out_be32(&pcie_law[1].bar, CONFIG_SYS_PCIE2_BASE & LAWBAR_BAR);
+	out_be32(&pcie_law[1].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+	if (pex2)
+		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX_X2,
+				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+	else
+		fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
+				 FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+	mpc83xx_pcie_init(pex2 ? 1 : 2, pcie_reg, 0);
+}
+
+void ft_pcie_fixup(void *blob, bd_t *bd)
+{
+	const char *status = "disabled (PCIE1 is x2)";
+
+	if (!is_pex_x2())
+		return;
+
+	do_fixup_by_path(blob, "pci2", "status", status,
+			 strlen(status) + 1, 1);
 }
 #endif /* CONFIG_PCI */
diff --git a/board/freescale/mpc837xemds/pci.h b/board/freescale/mpc837xemds/pci.h
new file mode 100644
index 0000000..fd7a916
--- /dev/null
+++ b/board/freescale/mpc837xemds/pci.h
@@ -0,0 +1,6 @@
+#ifndef __BOARD_MPC837XEMDS_PCI_H
+#define __BOARD_MPC837XEMDS_PCI_H
+
+extern void ft_pcie_fixup(void *blob, bd_t *bd);
+
+#endif /* __BOARD_MPC837XEMDS_PCI_H */
diff --git a/board/sheldon/simpc8313/Makefile b/board/sheldon/simpc8313/Makefile
new file mode 100644
index 0000000..7c34c5e
--- /dev/null
+++ b/board/sheldon/simpc8313/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o sdram.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/sheldon/simpc8313/config.mk b/board/sheldon/simpc8313/config.mk
new file mode 100644
index 0000000..ce1c0d8
--- /dev/null
+++ b/board/sheldon/simpc8313/config.mk
@@ -0,0 +1,13 @@
+ifndef NAND_SPL
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+endif
+
+ifndef TEXT_BASE
+TEXT_BASE = 0x00100000
+endif
+
+ifdef CONFIG_NAND_LP
+PAD_TO = 0xFFF20000
+else
+PAD_TO = 0xFFF04000
+endif
diff --git a/board/sheldon/simpc8313/sdram.c b/board/sheldon/simpc8313/sdram.c
new file mode 100644
index 0000000..ebb70a2
--- /dev/null
+++ b/board/sheldon/simpc8313/sdram.c
@@ -0,0 +1,193 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ * Copyright (C) Sheldon Instruments, Inc. 2008
+ *
+ * Author: Ron Madrid <info@sheldoninst.com>
+ *
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spd_sdram.h>
+#include <asm/bitops.h>
+#include <asm/io.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static long fixed_sdram(void);
+
+#if defined(CONFIG_NAND_SPL)
+void si_wait_i2c(void)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+
+	while (!(__raw_readb(&im->i2c[0].sr) & 0x02))
+		;
+
+	__raw_writeb(0x00, &im->i2c[0].sr);
+
+	sync();
+
+	return;
+}
+
+void si_read_i2c(u32 lbyte, int count, u8 *buffer)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+	u32 i;
+	u8 chip = 0x50 << 1; /* boot sequencer I2C */
+	u32 ubyte = (lbyte & 0xff00) >> 8;
+
+	lbyte &= 0xff;
+
+	/*
+	 * Set up controller
+	 */
+	__raw_writeb(0x3f, &im->i2c[0].fdr);
+	__raw_writeb(0x00, &im->i2c[0].adr);
+	__raw_writeb(0x00, &im->i2c[0].sr);
+	__raw_writeb(0x00, &im->i2c[0].dr);
+
+	while (__raw_readb(&im->i2c[0].sr) & 0x20)
+		;
+
+	/*
+	 * Writing address to device
+	 */
+	__raw_writeb(0xb0, &im->i2c[0].cr);
+	sync();
+	__raw_writeb(chip, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(0xb0, &im->i2c[0].cr);
+	sync();
+	__raw_writeb(ubyte, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(lbyte, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(0xb4, &im->i2c[0].cr);
+	sync();
+	__raw_writeb(chip + 1, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(0xa0, &im->i2c[0].cr);
+	sync();
+
+	/*
+	 * Dummy read
+	 */
+	__raw_readb(&im->i2c[0].dr);
+
+	si_wait_i2c();
+
+	/*
+	 * Read actual data
+	 */
+	for (i = 0; i < count; i++)
+	{
+		if (i == (count - 2))	/* Reached next to last byte, No ACK */
+			__raw_writeb(0xa8, &im->i2c[0].cr);
+		if (i == (count - 1))	/* Reached last byte, STOP */
+			__raw_writeb(0x88, &im->i2c[0].cr);
+
+		/* Read byte of data */
+		buffer[i] = __raw_readb(&im->i2c[0].dr);
+
+		if (i == (count - 1))
+			break;
+		si_wait_i2c();
+	}
+
+	return;
+}
+#endif /* CONFIG_NAND_SPL */
+
+phys_size_t initdram(int board_type)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+	volatile fsl_lbus_t *lbc= &im->lbus;
+	u32 msize;
+
+	if ((__raw_readl(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32) im)
+		return -1;
+
+	/* DDR SDRAM - Main SODIMM */
+	__raw_writel(CONFIG_SYS_DDR_BASE & LAWBAR_BAR, &im->sysconf.ddrlaw[0].bar);
+
+	msize = fixed_sdram();
+
+	/* Local Bus setup lbcr and mrtpr */
+	__raw_writel(CONFIG_SYS_LBC_LBCR, &lbc->lbcr);
+	__raw_writel(CONFIG_SYS_LBC_MRTPR, &lbc->mrtpr);
+	sync();
+
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return (msize * 1024 * 1024);
+}
+
+/*************************************************************************
+ *  fixed sdram init -- reads values from boot sequencer I2C
+ ************************************************************************/
+static long fixed_sdram(void)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+	u32 msizelog2, msize = 1;
+#if defined(CONFIG_NAND_SPL)
+	u32 i;
+	const u8 bytecount = 135;
+	u8 buffer[bytecount];
+	u32 addr, data;
+
+	si_read_i2c(0, bytecount, buffer);
+
+	for (i = 18; i < bytecount; i += 7){
+		addr = (u32)buffer[i];
+		addr <<= 8;
+		addr |= (u32)buffer[i + 1];
+		addr <<= 2;
+		data = (u32)buffer[i + 2];
+		data <<= 8;
+		data |= (u32)buffer[i + 3];
+		data <<= 8;
+		data |= (u32)buffer[i + 4];
+		data <<= 8;
+		data |= (u32)buffer[i + 5];
+
+		__raw_writel(data, (u32 *)(CONFIG_SYS_IMMR + addr));
+	}
+
+	sync();
+
+	/* enable DDR controller */
+	__raw_writel((__raw_readl(&im->ddr.sdram_cfg) | SDRAM_CFG_MEM_EN), &im->ddr.sdram_cfg);
+#endif /* (CONFIG_NAND_SPL) */
+
+	msizelog2 = ((__raw_readl(&im->sysconf.ddrlaw[0].ar) & LAWAR_SIZE) + 1);
+	msize <<= (msizelog2 - 20);
+
+	return msize;
+}
diff --git a/board/sheldon/simpc8313/simpc8313.c b/board/sheldon/simpc8313/simpc8313.c
new file mode 100644
index 0000000..25e5c24
--- /dev/null
+++ b/board/sheldon/simpc8313/simpc8313.c
@@ -0,0 +1,134 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ * Copyright (C) Sheldon Instruments, Inc. 2008
+ *
+ * Author: Ron Madrid <info@sheldoninst.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <ns16550.h>
+#include <nand.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	puts("Board: Sheldon Instruments SIMPC8313\n");
+	return 0;
+}
+
+#ifndef CONFIG_NAND_SPL
+static struct pci_region pci_regions[] = {
+	{
+		bus_start: CONFIG_SYS_PCI1_MEM_BASE,
+		phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
+		size: CONFIG_SYS_PCI1_MEM_SIZE,
+		flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
+		phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
+		size: CONFIG_SYS_PCI1_MMIO_SIZE,
+		flags: PCI_REGION_MEM
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_IO_BASE,
+		phys_start: CONFIG_SYS_PCI1_IO_PHYS,
+		size: CONFIG_SYS_PCI1_IO_SIZE,
+		flags: PCI_REGION_IO
+	}
+};
+
+void pci_init_board(void)
+{
+	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	struct pci_region *reg[] = { pci_regions };
+	int warmboot;
+
+	/* Enable all 3 PCI_CLK_OUTPUTs. */
+	clk->occr |= 0xe0000000;
+
+	/*
+	 * Configure PCI Local Access Windows
+	 */
+	pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
+	pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
+
+	pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
+	pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
+
+	warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM;
+
+	mpc83xx_pci_init(1, reg, warmboot);
+}
+
+/*
+ * Miscellaneous late-boot configurations
+ */
+int misc_init_r(void)
+{
+	int rc = 0;
+
+	return rc;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+#ifdef CONFIG_PCI
+	ft_pci_setup(blob, bd);
+#endif
+}
+#endif
+#else /* CONFIG_NAND_SPL */
+void board_init_f(ulong bootflag)
+{
+	NS16550_init((NS16550_t)(CONFIG_SYS_IMMR + 0x4500),
+				CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE);
+	puts("NAND boot... ");
+	init_timebase();
+	initdram(0);
+	relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000, (gd_t *)gd,
+				  CONFIG_SYS_NAND_U_BOOT_RELOC);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	nand_boot();
+}
+
+void putc(char c)
+{
+	if (gd->flags & GD_FLG_SILENT)
+		return;
+
+	if (c == '\n')
+		NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), '\r');
+
+	NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), c);
+}
+#endif
diff --git a/cpu/mpc83xx/Makefile b/cpu/mpc83xx/Makefile
index fcb6a52..dd35e6b 100644
--- a/cpu/mpc83xx/Makefile
+++ b/cpu/mpc83xx/Makefile
@@ -39,6 +39,7 @@ COBJS-y += ecc.o
 COBJS-$(CONFIG_QE) += qe_io.o
 COBJS-$(CONFIG_FSL_SERDES) += serdes.o
 COBJS-$(CONFIG_83XX_GENERIC_PCI) += pci.o
+COBJS-$(CONFIG_83XX_GENERIC_PCIE) += pcie.o
 COBJS-$(CONFIG_OF_LIBFDT) += fdt.o
 
 COBJS	:= $(COBJS-y)
diff --git a/cpu/mpc83xx/pci.c b/cpu/mpc83xx/pci.c
index ab0760b..e9965d7 100644
--- a/cpu/mpc83xx/pci.c
+++ b/cpu/mpc83xx/pci.c
@@ -118,10 +118,12 @@ static void pci_init_bus(int bus, struct pci_region *reg)
 #ifdef CONFIG_PCI_SCAN_SHOW
 	printf("PCI:   Bus Dev VenId DevId Class Int\n");
 #endif
+#ifndef CONFIG_PCISLAVE
 	/*
 	 * Hose scan.
 	 */
 	hose->last_busno = pci_hose_scan(hose);
+#endif
 }
 
 /*
@@ -190,6 +192,9 @@ void mpc83xx_pcislave_unlock(int bus)
 	pci_hose_read_config_word (hose, dev, PCI_FUNCTION_CONFIG, &reg16);
 	reg16 &= ~(PCI_FUNCTION_CFG_LOCK);
 	pci_hose_write_config_word (hose, dev, PCI_FUNCTION_CONFIG, reg16);
+
+	/* The configuration bit is now unlocked, so we can scan the bus */
+	hose->last_busno = pci_hose_scan(hose);
 }
 #endif
 
diff --git a/cpu/mpc83xx/pcie.c b/cpu/mpc83xx/pcie.c
new file mode 100644
index 0000000..02150ba
--- /dev/null
+++ b/cpu/mpc83xx/pcie.c
@@ -0,0 +1,314 @@
+/*
+ * Copyright (C) 2007-2009  Freescale Semiconductor, Inc.
+ * Copyright (C) 2008-2009  MontaVista Software, Inc.
+ *
+ * Authors: Tony Li <tony.li@freescale.com>
+ *          Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define PCIE_MAX_BUSES 2
+
+#ifdef CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES
+
+static int mpc83xx_pcie_remap_cfg(struct pci_controller *hose, pci_dev_t dev)
+{
+	int bus = PCI_BUS(dev) - hose->first_busno;
+	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+	pex83xx_t *pex = &immr->pciexp[bus];
+	struct pex_outbound_window *out_win = &pex->bridge.pex_outbound_win[0];
+	u8 devfn = PCI_DEV(dev) << 3 | PCI_FUNC(dev);
+	u32 dev_base = bus << 24 | devfn << 16;
+
+	if (hose->indirect_type == INDIRECT_TYPE_NO_PCIE_LINK)
+		return -1;
+	/*
+	 * Workaround for the HW bug: for Type 0 configure transactions the
+	 * PCI-E controller does not check the device number bits and just
+	 * assumes that the device number bits are 0.
+	 */
+	if (devfn & 0xf8)
+		return -1;
+
+	out_le32(&out_win->tarl, dev_base);
+	return 0;
+}
+
+#define cfg_read(val, addr, type, op) \
+	do { *val = op((type)(addr)); } while (0)
+#define cfg_write(val, addr, type, op) \
+	do { op((type *)(addr), (val)); } while (0)
+
+#define PCIE_OP(rw, size, type, op)					\
+static int pcie_##rw##_config_##size(struct pci_controller *hose,	\
+				     pci_dev_t dev, int offset,		\
+				     type val)				\
+{									\
+	int ret;							\
+									\
+	ret = mpc83xx_pcie_remap_cfg(hose, dev);			\
+	if (ret)							\
+		return ret;						\
+	cfg_##rw(val, (void *)hose->cfg_addr + offset, type, op);	\
+	return 0;							\
+}
+
+PCIE_OP(read, byte, u8 *, in_8)
+PCIE_OP(read, word, u16 *, in_le16)
+PCIE_OP(read, dword, u32 *, in_le32)
+PCIE_OP(write, byte, u8, out_8)
+PCIE_OP(write, word, u16, out_le16)
+PCIE_OP(write, dword, u32, out_le32)
+
+static void mpc83xx_pcie_register_hose(int bus, struct pci_region *reg,
+				       u8 link)
+{
+	extern void disable_addr_trans(void); /* start.S */
+	static struct pci_controller pcie_hose[PCIE_MAX_BUSES];
+	static int max_bus;
+	struct pci_controller *hose = &pcie_hose[bus];
+	int i;
+
+	/*
+	 * There are no spare BATs to remap all PCI-E windows for U-Boot, so
+	 * disable translations. In general, this is not great solution, and
+	 * that's why we don't register PCI-E hoses by default.
+	 */
+	disable_addr_trans();
+
+	for (i = 0; i < 2; i++, reg++) {
+		if (reg->size == 0)
+			break;
+
+		hose->regions[i] = *reg;
+		hose->region_count++;
+	}
+
+	i = hose->region_count++;
+	hose->regions[i].bus_start = 0;
+	hose->regions[i].phys_start = 0;
+	hose->regions[i].size = gd->ram_size;
+	hose->regions[i].flags = PCI_REGION_MEM | PCI_REGION_MEMORY;
+
+	i = hose->region_count++;
+	hose->regions[i].bus_start = CONFIG_SYS_IMMR;
+	hose->regions[i].phys_start = CONFIG_SYS_IMMR;
+	hose->regions[i].size = 0x100000;
+	hose->regions[i].flags = PCI_REGION_MEM | PCI_REGION_MEMORY;
+
+	hose->first_busno = max_bus;
+	hose->last_busno = 0xff;
+
+	if (bus == 0)
+		hose->cfg_addr = (unsigned int *)CONFIG_SYS_PCIE1_CFG_BASE;
+	else
+		hose->cfg_addr = (unsigned int *)CONFIG_SYS_PCIE2_CFG_BASE;
+
+	pci_set_ops(hose,
+			pcie_read_config_byte,
+			pcie_read_config_word,
+			pcie_read_config_dword,
+			pcie_write_config_byte,
+			pcie_write_config_word,
+			pcie_write_config_dword);
+
+	if (!link)
+		hose->indirect_type = INDIRECT_TYPE_NO_PCIE_LINK;
+
+	pci_register_hose(hose);
+
+#ifdef CONFIG_PCI_SCAN_SHOW
+	printf("PCI:   Bus Dev VenId DevId Class Int\n");
+#endif
+	/*
+	 * Hose scan.
+	 */
+	hose->last_busno = pci_hose_scan(hose);
+	max_bus = hose->last_busno + 1;
+}
+
+#else
+
+static void mpc83xx_pcie_register_hose(int bus, struct pci_region *reg,
+				       u8 link) {}
+
+#endif /* CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES */
+
+static void mpc83xx_pcie_init_bus(int bus, struct pci_region *reg)
+{
+	immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+	pex83xx_t *pex = &immr->pciexp[bus];
+	struct pex_outbound_window *out_win;
+	struct pex_inbound_window *in_win;
+	void *hose_cfg_base;
+	unsigned int ram_sz;
+	unsigned int barl;
+	unsigned int tar;
+	u16 reg16;
+	int i;
+
+	/* Enable pex csb bridge inbound & outbound transactions */
+	out_le32(&pex->bridge.pex_csb_ctrl,
+		in_le32(&pex->bridge.pex_csb_ctrl) | PEX_CSB_CTRL_OBPIOE |
+		PEX_CSB_CTRL_IBPIOE);
+
+	/* Enable bridge outbound */
+	out_le32(&pex->bridge.pex_csb_obctrl, PEX_CSB_OBCTRL_PIOE |
+		PEX_CSB_OBCTRL_MEMWE | PEX_CSB_OBCTRL_IOWE |
+		PEX_CSB_OBCTRL_CFGWE);
+
+	out_win = &pex->bridge.pex_outbound_win[0];
+	if (bus) {
+		out_le32(&out_win->ar, PEX_OWAR_EN | PEX_OWAR_TYPE_CFG |
+			CONFIG_SYS_PCIE2_CFG_SIZE);
+		out_le32(&out_win->bar, CONFIG_SYS_PCIE2_CFG_BASE);
+	} else {
+		out_le32(&out_win->ar, PEX_OWAR_EN | PEX_OWAR_TYPE_CFG |
+			CONFIG_SYS_PCIE1_CFG_SIZE);
+		out_le32(&out_win->bar, CONFIG_SYS_PCIE1_CFG_BASE);
+	}
+	out_le32(&out_win->tarl, 0);
+	out_le32(&out_win->tarh, 0);
+
+	for (i = 0; i < 2; i++, reg++) {
+		u32 ar;
+
+		if (reg->size == 0)
+			break;
+
+		out_win = &pex->bridge.pex_outbound_win[i + 1];
+		out_le32(&out_win->bar, reg->phys_start);
+		out_le32(&out_win->tarl, reg->bus_start);
+		out_le32(&out_win->tarh, 0);
+		ar = PEX_OWAR_EN | (reg->size & PEX_OWAR_SIZE);
+		if (reg->flags & PCI_REGION_IO)
+			ar |= PEX_OWAR_TYPE_IO;
+		else
+			ar |= PEX_OWAR_TYPE_MEM;
+		out_le32(&out_win->ar, ar);
+	}
+
+	out_le32(&pex->bridge.pex_csb_ibctrl, PEX_CSB_IBCTRL_PIOE);
+
+	ram_sz = gd->ram_size;
+	barl = 0;
+	tar = 0;
+	i = 0;
+	while (ram_sz > 0) {
+		in_win = &pex->bridge.pex_inbound_win[i];
+		out_le32(&in_win->barl, barl);
+		out_le32(&in_win->barh, 0x0);
+		out_le32(&in_win->tar, tar);
+		if (ram_sz >= 0x10000000) {
+			/* The maxium windows size is 256M */
+			out_le32(&in_win->ar, PEX_IWAR_EN | PEX_IWAR_NSOV |
+				PEX_IWAR_TYPE_PF | 0x0FFFF000);
+			barl += 0x10000000;
+			tar += 0x10000000;
+			ram_sz -= 0x10000000;
+		} else {
+			/* The UM  is not clear here.
+			 * So, round up to even Mb boundary */
+
+			ram_sz = ram_sz >> (20 +
+					((ram_sz & 0xFFFFF) ? 1 : 0));
+			if (!(ram_sz % 2))
+				ram_sz -= 1;
+			out_le32(&in_win->ar, PEX_IWAR_EN | PEX_IWAR_NSOV |
+				PEX_IWAR_TYPE_PF | (ram_sz << 20) | 0xFF000);
+			ram_sz = 0;
+		}
+		i++;
+	}
+
+	in_win = &pex->bridge.pex_inbound_win[i];
+	out_le32(&in_win->barl, CONFIG_SYS_IMMR);
+	out_le32(&in_win->barh, 0);
+	out_le32(&in_win->tar, CONFIG_SYS_IMMR);
+	out_le32(&in_win->ar, PEX_IWAR_EN |
+		PEX_IWAR_TYPE_NO_PF | PEX_IWAR_SIZE_1M);
+
+	/* Enable the host virtual INTX interrupts */
+	out_le32(&pex->bridge.pex_int_axi_misc_enb,
+		in_le32(&pex->bridge.pex_int_axi_misc_enb) | 0x1E0);
+
+	/* Hose configure header is memory-mapped */
+	hose_cfg_base = (void *)pex;
+
+	get_clocks();
+	/* Configure the PCIE controller core clock ratio */
+	out_le32(hose_cfg_base + PEX_GCLK_RATIO,
+		(((bus ? gd->pciexp2_clk : gd->pciexp1_clk) / 1000000) * 16)
+		/ 333);
+	udelay(1000000);
+
+	/* Do Type 1 bridge configuration */
+	out_8(hose_cfg_base + PCI_PRIMARY_BUS, 0);
+	out_8(hose_cfg_base + PCI_SECONDARY_BUS, 1);
+	out_8(hose_cfg_base + PCI_SUBORDINATE_BUS, 255);
+
+	/*
+	 * Write to Command register
+	 */
+	reg16 = in_le16(hose_cfg_base + PCI_COMMAND);
+	reg16 |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO |
+			PCI_COMMAND_SERR | PCI_COMMAND_PARITY;
+	out_le16(hose_cfg_base + PCI_COMMAND, reg16);
+
+	/*
+	 * Clear non-reserved bits in status register.
+	 */
+	out_le16(hose_cfg_base + PCI_STATUS, 0xffff);
+	out_8(hose_cfg_base + PCI_LATENCY_TIMER, 0x80);
+	out_8(hose_cfg_base + PCI_CACHE_LINE_SIZE, 0x08);
+
+	printf("PCIE%d: ", bus);
+
+	reg16 = in_le16(hose_cfg_base + PCI_LTSSM);
+	if (reg16 >= PCI_LTSSM_L0)
+		printf("link\n");
+	else
+		printf("No link\n");
+
+	mpc83xx_pcie_register_hose(bus, reg, reg16 >= PCI_LTSSM_L0);
+}
+
+/*
+ * The caller must have already set SCCR, SERDES and the PCIE_LAW BARs
+ * must have been set to cover all of the requested regions.
+ */
+void mpc83xx_pcie_init(int num_buses, struct pci_region **reg, int warmboot)
+{
+	int i;
+
+	/*
+	 * Release PCI RST Output signal.
+	 * Power on to RST high must be at least 100 ms as per PCI spec.
+	 * On warm boots only 1 ms is required.
+	 */
+	udelay(warmboot ? 1000 : 100000);
+
+	for (i = 0; i < num_buses; i++)
+		mpc83xx_pcie_init_bus(i, reg[i]);
+}
diff --git a/cpu/mpc83xx/speed.c b/cpu/mpc83xx/speed.c
index bf9bf36..4230099 100644
--- a/cpu/mpc83xx/speed.c
+++ b/cpu/mpc83xx/speed.c
@@ -132,7 +132,7 @@ int get_clocks(void)
 	u32 qe_clk;
 	u32 brg_clk;
 #endif
-#if defined(CONFIG_MPC837X)
+#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC831X)
 	u32 pciexp1_clk;
 	u32 pciexp2_clk;
 #endif
@@ -328,7 +328,7 @@ int get_clocks(void)
 	i2c2_clk = csb_clk; /* i2c-2 clk is equal to csb clk */
 #endif
 
-#if defined(CONFIG_MPC837X)
+#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC831X)
 	switch ((sccr & SCCR_PCIEXP1CM) >> SCCR_PCIEXP1CM_SHIFT) {
 	case 0:
 		pciexp1_clk = 0;
diff --git a/cpu/mpc83xx/start.S b/cpu/mpc83xx/start.S
index 792b2c8..26e3106 100644
--- a/cpu/mpc83xx/start.S
+++ b/cpu/mpc83xx/start.S
@@ -109,6 +109,45 @@ version_string:
 	.ascii " (", U_BOOT_DATE, " - ", U_BOOT_TIME, ")"
 	.ascii " ", CONFIG_IDENT_STRING, "\0"
 
+	.align 2
+
+	.globl enable_addr_trans
+enable_addr_trans:
+	/* enable address translation */
+	mfmsr	r5
+	ori	r5, r5, (MSR_IR | MSR_DR)
+	mtmsr	r5
+	isync
+	blr
+
+	.globl disable_addr_trans
+disable_addr_trans:
+	/* disable address translation */
+	mflr	r4
+	mfmsr	r3
+	andi.	r0, r3, (MSR_IR | MSR_DR)
+	beqlr
+	andc	r3, r3, r0
+	mtspr	SRR0, r4
+	mtspr	SRR1, r3
+	rfi
+
+	.globl get_pvr
+get_pvr:
+	mfspr	r3, PVR
+	blr
+
+	.globl	ppcDWstore
+ppcDWstore:
+	lfd	1, 0(r4)
+	stfd	1, 0(r3)
+	blr
+
+	.globl	ppcDWload
+ppcDWload:
+	lfd	1, 0(r3)
+	stfd	1, 0(r4)
+	blr
 
 #ifndef CONFIG_DEFAULT_IMMR
 #error CONFIG_DEFAULT_IMMR must be defined
@@ -161,9 +200,23 @@ boot_cold: /* time t 3 */
 	nop
 boot_warm: /* time t 5 */
 	mfmsr	r5			/* save msr contents	*/
+
+	/* 83xx manuals prescribe a specific sequence for updating IMMRBAR. */
+	bl	1f
+1:	mflr	r7
+
 	lis	r3, CONFIG_SYS_IMMR@h
 	ori	r3, r3, CONFIG_SYS_IMMR@l
+
+	lwz	r6, IMMRBAR(r4)
+	isync
+
 	stw	r3, IMMRBAR(r4)
+	lwz	r6, 0(r7)		/* Arbitrary external load */
+	isync
+
+	lwz	r6, IMMRBAR(r3)
+	isync
 
 	/* Initialise the E300 processor core		*/
 	/*------------------------------------------*/
@@ -173,9 +226,7 @@ boot_warm: /* time t 5 */
 	 * is loaded.  Wait for the rest before branching
 	 * to another flash page.
 	 */
-	addi	r7, r3, 0x50b0
-1:	dcbi	0, r7
-	lwz	r6, 0(r7)
+1:	lwz	r6, 0x50b0(r3)
 	andi.	r6, r6, 1
 	beq	1b
 #endif
@@ -698,27 +749,6 @@ setup_bats:
 
 	blr
 
-	.globl enable_addr_trans
-enable_addr_trans:
-	/* enable address translation */
-	mfmsr	r5
-	ori	r5, r5, (MSR_IR | MSR_DR)
-	mtmsr	r5
-	isync
-	blr
-
-	.globl disable_addr_trans
-disable_addr_trans:
-	/* disable address translation */
-	mflr	r4
-	mfmsr	r3
-	andi.	r0, r3, (MSR_IR | MSR_DR)
-	beqlr
-	andc	r3, r3, r0
-	mtspr	SRR0, r4
-	mtspr	SRR1, r3
-	rfi
-
 /* Cache functions.
  *
  * Note: requires that all cache bits in
@@ -796,23 +826,6 @@ flush_dcache:
 	b	1b
 2:	blr
 
-	.globl get_pvr
-get_pvr:
-	mfspr	r3, PVR
-	blr
-
-	.globl	ppcDWstore
-ppcDWstore:
-	lfd	1, 0(r4)
-	stfd	1, 0(r3)
-	blr
-
-	.globl	ppcDWload
-ppcDWload:
-	lfd	1, 0(r3)
-	stfd	1, 0(r4)
-	blr
-
 /*-------------------------------------------------------------------*/
 
 /*
diff --git a/doc/README.simpc8313 b/doc/README.simpc8313
new file mode 100644
index 0000000..b362c6a
--- /dev/null
+++ b/doc/README.simpc8313
@@ -0,0 +1,80 @@
+Sheldon Instruments SIMPC8313 Board
+-----------------------------------------
+
+1.	Board Switches and Jumpers
+
+	S2 is used to set CFG_RESET_SOURCE.
+
+	To boot the image in Large page NAND flash, use these DIP
+	switch settings for S2:
+
+	+----------+ ON
+	| * * **** |
+	|  * *     |
+	+----------+
+	  12345678
+
+	To boot the image in Small page NAND flash, use these DIP
+	switch settings for S2:
+
+	+----------+ ON
+	| *** **** |
+	|    *     |
+	+----------+
+	  12345678
+	(where the '*' indicates the position of the tab of the switch.)
+
+2.	Memory Map
+	The memory map looks like this:
+
+	0x0000_0000	0x1fff_ffff	DDR			512M
+	0x8000_0000	0x8fff_ffff	PCI MEM			256M
+	0x9000_0000	0x9fff_ffff	PCI_MMIO		256M
+	0xe000_0000	0xe00f_ffff	IMMR			1M
+	0xe200_0000	0xe20f_ffff	PCI IO			16M
+	0xe280_0000	0xe280_7fff	NAND FLASH (CS0)	32K
+	or
+	0xe280_0000	0xe281_ffff	NAND FLASH (CS0)	128K
+	0xff00_0000	0xff00_7fff	FPGA (CS1)		1M
+
+3.	Compilation
+
+	Assuming you're using BASH (or similar) as your shell:
+
+	export CROSS_COMPILE=your-cross-compiler-prefix-
+	make distclean
+	make SIMPC8313_LP_config
+	(or make SIMPC8313_SP_config, depending on the page size
+	of your NAND flash)
+	make
+
+4.	Downloading and Flashing Images
+
+4.1	Reflash U-boot Image using U-boot
+
+	=>run update_uboot
+
+	You may want to try
+	=>tftp $loadaddr $uboot
+	first, to make sure that the TFTP load will succeed before it
+	goes ahead and wipes out your current firmware.  And of course,
+	if the new u-boot doesn't boot, you can plug the board into
+	your PCI slot and with the supplied driver and sample app
+	you can reburn a working u-boot.
+
+4.2	Downloading and Booting Linux Kernel
+
+	Ensure that all networking-related environment variables are set
+	properly (including ipaddr, serverip, gatewayip (if needed),
+	netmask, ethaddr, eth1addr, fdtfile, and bootfile).
+
+	=>tftp $loadaddr uImage
+	=>nand write $loadaddr kernel $filesize
+	=>tftp $loadaddr $fdtfile
+	=>nand write $loadaddr 7e0000 1800
+
+	=>boot
+
+5	Notes
+
+	The console baudrate for SIMPC8313 is 115200bps.
diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h
index 2bb50b4..e5a3b2c 100644
--- a/include/asm-ppc/global_data.h
+++ b/include/asm-ppc/global_data.h
@@ -75,7 +75,7 @@ typedef	struct	global_data {
 	u32 lbiu_clk;
 	u32 lclk_clk;
 	u32 pci_clk;
-#if defined(CONFIG_MPC837X)
+#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC831X)
 	u32 pciexp1_clk;
 	u32 pciexp2_clk;
 #endif
diff --git a/include/asm-ppc/immap_83xx.h b/include/asm-ppc/immap_83xx.h
index df24a6e..77c09db 100644
--- a/include/asm-ppc/immap_83xx.h
+++ b/include/asm-ppc/immap_83xx.h
@@ -52,23 +52,28 @@ typedef struct sysconf83xx {
 	law83xx_t lblaw[4];	/* LBIU local access window */
 	u8 res2[0x20];
 	law83xx_t pcilaw[2];	/* PCI local access window */
-	u8 res3[0x30];
+	u8 res3[0x10];
+	law83xx_t pcielaw[2];	/* PCI Express local access window */
+	u8 res4[0x10];
 	law83xx_t ddrlaw[2];	/* DDR local access window */
-	u8 res4[0x50];
+	u8 res5[0x50];
 	u32 sgprl;		/* System General Purpose Register Low */
 	u32 sgprh;		/* System General Purpose Register High */
 	u32 spridr;		/* System Part and Revision ID Register */
-	u8 res5[0x04];
+	u8 res6[0x04];
 	u32 spcr;		/* System Priority Configuration Register */
 	u32 sicrl;		/* System I/O Configuration Register Low */
 	u32 sicrh;		/* System I/O Configuration Register High */
-	u8 res6[0x04];
+	u8 res7[0x04];
 	u32 sidcr0;		/* System I/O Delay Configuration Register 0 */
 	u32 sidcr1;		/* System I/O Delay Configuration Register 1 */
 	u32 ddrcdr;		/* DDR Control Driver Register */
 	u32 ddrdsr;		/* DDR Debug Status Register */
 	u32 obir;		/* Output Buffer Impedance Register */
-	u8 res7[0xCC];
+	u8 res8[0xC];
+	u32 pecr1;		/* PCI Express control register 1 */
+	u32 pecr2;		/* PCI Express control register 2 */
+	u8 res9[0xB8];
 } sysconf83xx_t;
 
 /*
@@ -503,8 +508,110 @@ typedef struct security83xx {
 /*
  *  PCI Express
  */
+struct pex_inbound_window {
+	u32 ar;
+	u32 tar;
+	u32 barl;
+	u32 barh;
+};
+
+struct pex_outbound_window {
+	u32 ar;
+	u32 bar;
+	u32 tarl;
+	u32 tarh;
+};
+
+struct pex_csb_bridge {
+	u32 pex_csb_ver;
+	u32 pex_csb_cab;
+	u32 pex_csb_ctrl;
+	u8 res0[8];
+	u32 pex_dms_dstmr;
+	u8 res1[4];
+	u32 pex_cbs_stat;
+	u8 res2[0x20];
+	u32 pex_csb_obctrl;
+	u32 pex_csb_obstat;
+	u8 res3[0x98];
+	u32 pex_csb_ibctrl;
+	u32 pex_csb_ibstat;
+	u8 res4[0xb8];
+	u32 pex_wdma_ctrl;
+	u32 pex_wdma_addr;
+	u32 pex_wdma_stat;
+	u8 res5[0x94];
+	u32 pex_rdma_ctrl;
+	u32 pex_rdma_addr;
+	u32 pex_rdma_stat;
+	u8 res6[0xd4];
+	u32 pex_ombcr;
+	u32 pex_ombdr;
+	u8 res7[0x38];
+	u32 pex_imbcr;
+	u32 pex_imbdr;
+	u8 res8[0x38];
+	u32 pex_int_enb;
+	u32 pex_int_stat;
+	u32 pex_int_apio_vec1;
+	u32 pex_int_apio_vec2;
+	u8 res9[0x10];
+	u32 pex_int_ppio_vec1;
+	u32 pex_int_ppio_vec2;
+	u32 pex_int_wdma_vec1;
+	u32 pex_int_wdma_vec2;
+	u32 pex_int_rdma_vec1;
+	u32 pex_int_rdma_vec2;
+	u32 pex_int_misc_vec;
+	u8 res10[4];
+	u32 pex_int_axi_pio_enb;
+	u32 pex_int_axi_wdma_enb;
+	u32 pex_int_axi_rdma_enb;
+	u32 pex_int_axi_misc_enb;
+	u32 pex_int_axi_pio_stat;
+	u32 pex_int_axi_wdma_stat;
+	u32 pex_int_axi_rdma_stat;
+	u32 pex_int_axi_misc_stat;
+	u8 res11[0xa0];
+	struct pex_outbound_window pex_outbound_win[4];
+	u8 res12[0x100];
+	u32 pex_epiwtar0;
+	u32 pex_epiwtar1;
+	u32 pex_epiwtar2;
+	u32 pex_epiwtar3;
+	u8 res13[0x70];
+	struct pex_inbound_window pex_inbound_win[4];
+};
+
 typedef struct pex83xx {
-	u8 fixme[0x1000];
+	u8 pex_cfg_header[0x404];
+	u32 pex_ltssm_stat;
+	u8 res0[0x30];
+	u32 pex_ack_replay_timeout;
+	u8 res1[4];
+	u32 pex_gclk_ratio;
+	u8 res2[0xc];
+	u32 pex_pm_timer;
+	u32 pex_pme_timeout;
+	u8 res3[4];
+	u32 pex_aspm_req_timer;
+	u8 res4[0x18];
+	u32 pex_ssvid_update;
+	u8 res5[0x34];
+	u32 pex_cfg_ready;
+	u8 res6[0x24];
+	u32 pex_bar_sizel;
+	u8 res7[4];
+	u32 pex_bar_sel;
+	u8 res8[0x20];
+	u32 pex_bar_pf;
+	u8 res9[0x88];
+	u32 pex_pme_to_ack_tor;
+	u8 res10[0xc];
+	u32 pex_ss_intr_mask;
+	u8 res11[0x25c];
+	struct pex_csb_bridge bridge;
+	u8 res12[0x160];
 } pex83xx_t;
 
 /*
diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h
index e4ada65..a04868e 100644
--- a/include/configs/MPC8315ERDB.h
+++ b/include/configs/MPC8315ERDB.h
@@ -309,8 +309,29 @@
 #define CONFIG_SYS_PCI_SLV_MEM_BUS	0x00000000
 #define CONFIG_SYS_PCI_SLV_MEM_SIZE	0x80000000
 
+#define CONFIG_SYS_PCIE1_BASE		0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
+#define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
+#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
+
+#define CONFIG_SYS_PCIE2_BASE		0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_BASE	0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xC0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000
+#define CONFIG_SYS_PCIE2_CFG_BASE	0xD0000000
+#define CONFIG_SYS_PCIE2_CFG_SIZE	0x01000000
+#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xD1000000
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000
+
 #define CONFIG_PCI
 #define CONFIG_83XX_GENERIC_PCI	1 /* Use generic PCI setup */
+#define CONFIG_83XX_GENERIC_PCIE	1
 
 #define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP		/* do pci plug-and-play */
diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h
index dbffb71..0dd6ef5 100644
--- a/include/configs/MPC837XEMDS.h
+++ b/include/configs/MPC837XEMDS.h
@@ -353,11 +353,32 @@
 #define CONFIG_SYS_PCI_SLV_MEM_BUS	0x00000000
 #define CONFIG_SYS_PCI_SLV_MEM_SIZE	0x80000000
 
+#define CONFIG_SYS_PCIE1_BASE		0xA0000000
+#define CONFIG_SYS_PCIE1_CFG_BASE	0xA0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE	0x08000000
+#define CONFIG_SYS_PCIE1_MEM_BASE	0xA8000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xA8000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
+#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xB8000000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
+
+#define CONFIG_SYS_PCIE2_BASE		0xC0000000
+#define CONFIG_SYS_PCIE2_CFG_BASE	0xC0000000
+#define CONFIG_SYS_PCIE2_CFG_SIZE	0x08000000
+#define CONFIG_SYS_PCIE2_MEM_BASE	0xC8000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xC8000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000
+#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xD8000000
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000
+
 #ifdef CONFIG_PCI
 #ifndef __ASSEMBLY__
 extern int board_pci_host_broken(void);
 #endif
 #define CONFIG_83XX_GENERIC_PCI	1 /* Use generic PCI setup */
+#define CONFIG_83XX_GENERIC_PCIE	1
 #define CONFIG_PQ_MDS_PIB	1 /* PQ MDS Platform IO Board */
 
 #define CONFIG_HAS_FSL_DR_USB	1 /* fixup device tree for the DR USB */
diff --git a/include/configs/SIMPC8313.h b/include/configs/SIMPC8313.h
new file mode 100644
index 0000000..a616236
--- /dev/null
+++ b/include/configs/SIMPC8313.h
@@ -0,0 +1,544 @@
+/*
+ * Copyright (C) Sheldon Instruments, Inc. 2008
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/*
+ * simpc8313 board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_NAND_U_BOOT
+
+#define CONFIG_E300			1
+#define CONFIG_MPC83XX			1
+#define CONFIG_MPC831X			1
+#define CONFIG_MPC8313			1
+
+#define CONFIG_PCI
+#define CONFIG_83XX_GENERIC_PCI
+
+#define CONFIG_MISC_INIT_R
+
+/*
+ * On-board devices
+ *
+ * TSEC1 is Marvell PHY 88E1118
+ */
+
+#define CONFIG_SYS_33MHZ
+
+#define CONFIG_83XX_CLKIN		33333333	/* in Hz */
+
+#define CONFIG_SYS_CLK_FREQ		CONFIG_83XX_CLKIN
+
+#define CONFIG_SYS_IMMR			0xE0000000
+
+#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_DEFAULT_IMMR		CONFIG_SYS_IMMR
+#endif
+
+#define CONFIG_SYS_MEMTEST_START	0x00001000
+#define CONFIG_SYS_MEMTEST_END		0x07f00000
+
+#define CONFIG_SYS_ACR_PIPE_DEP		3	/* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
+
+/*
+ * Device configurations
+ */
+#define CONFIG_TSEC1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000	/* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_MAX_MEM_MAPPED		(512 << 20)
+
+#define CONFIG_SYS_DDRCDR		( DDRCDR_EN \
+					| DDRCDR_PZ_NOMZ \
+					| DDRCDR_NZ_NOMZ \
+					| DDRCDR_M_ODR )
+					/* 0x73000002 TODO ODR & DRN ? */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#if !defined(CONFIG_NAND_SPL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000	/* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END		0x1000		/* End of used area in RAM*/
+
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100		/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(512 * 1024)	/* Reserved for malloc */
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CONFIG_SYS_LCRR		(LCRR_DBYP | LCRR_EADC_1 | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LBC_LBCR	(0x00040000 /* TODO */ \
+				| (0xFF << LBCR_BMT_SHIFT) \
+				| 0xF )	/* 0x0004ff0f */
+
+#define CONFIG_SYS_LBC_MRTPR	0x20000000	/* LB refresh timer prescal, 266MHz/32 */
+
+/* drivers/mtd/nand/nand.c */
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_SYS_NAND_BASE		0xFFF00000
+#else
+#define CONFIG_SYS_NAND_BASE		0xE2800000
+#endif
+
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define NAND_MAX_CHIPS			1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND 		1
+#define CONFIG_NAND_FSL_ELBC		1
+
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST	0x00100000
+#define CONFIG_SYS_NAND_U_BOOT_START	0x00100100
+#define CONFIG_SYS_NAND_U_BOOT_RELOC	0x00010000
+
+#define CONFIG_SYS_NAND_BR_PRELIM	( CONFIG_SYS_NAND_BASE \
+					| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
+					| BR_PS_8		/* Port Size = 8 bit */ \
+					| BR_MS_FCM		/* MSEL = FCM */ \
+					| BR_V )		/* valid */
+
+#ifdef CONFIG_NAND_SP
+#define CONFIG_SYS_NAND_OR_PRELIM	( 0xFFFF8000	/* length 32K */ \
+					| OR_FCM_CSCT \
+					| OR_FCM_CST \
+					| OR_FCM_CHT \
+					| OR_FCM_SCY_1 \
+					| OR_FCM_TRLX \
+					| OR_FCM_EHTR )
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x8000000E	/* 32KB */
+#define CONFIG_SYS_NAND_PAGE_SIZE	(512)		/* NAND chip page size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 << 10)	/* NAND chip block size */
+#define NAND_CACHE_PAGES		32
+#elif defined(CONFIG_NAND_LP)
+#define CONFIG_SYS_NAND_OR_PRELIM	( 0xFFFC0000	/* length 256K */ \
+					| OR_FCM_PGS \
+					| OR_FCM_CSCT \
+					| OR_FCM_CST \
+					| OR_FCM_CHT \
+					| OR_FCM_SCY_1 \
+					| OR_FCM_TRLX \
+					| OR_FCM_EHTR )
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000011	/* 256KB */
+#define CONFIG_SYS_NAND_PAGE_SIZE	(2048)		/* NAND chip page size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)	/* NAND chip block size */
+#define NAND_CACHE_PAGES		64
+#else
+#error Page size of NAND not defined.
+#endif /* CONFIG_NAND_SP */
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SYS_NAND_BLOCK_SIZE
+
+#define CONFIG_SYS_BR0_PRELIM		CONFIG_SYS_NAND_BR_PRELIM
+#define CONFIG_SYS_OR0_PRELIM		CONFIG_SYS_NAND_OR_PRELIM
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM	CONFIG_SYS_LBLAWBAR0_PRELIM
+#define CONFIG_SYS_NAND_LBLAWAR_PRELIM	CONFIG_SYS_LBLAWAR0_PRELIM
+
+/*
+ * JFFS2 configuration
+ */
+#define CONFIG_JFFS2_NAND
+#define CONFIG_JFFS2_DEV	"nand0"
+
+/* mtdparts command line support */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nand0=nand0"
+#define MTDPARTS_DEFAULT	"mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)"
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1		(CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2		(CONFIG_SYS_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/* I2C */
+#define CONFIG_HARD_I2C			/* I2C with hardware support*/
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_NOPROBES		{{0,0x69}} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C2_OFFSET		0x3100
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */
+
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1057	/* Motorola */
+
+/*
+ * TSEC
+ */
+#define CONFIG_TSEC_ENET		/* TSEC ethernet support */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_GMII			/* MII PHY management */
+
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
+#define CONFIG_TSEC1_NAME		"TSEC0"
+#define CONFIG_SYS_TSEC1_OFFSET		0x24000
+#define TSEC1_PHY_ADDR			0x0
+#define TSEC1_FLAGS			TSEC_GIGABIT
+#define TSEC1_PHYIDX			0
+#endif
+
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
+#define CONFIG_TSEC2_NAME		"TSEC1"
+#define CONFIG_SYS_TSEC2_OFFSET		0x25000
+#define TSEC2_PHY_ADDR			4
+#define TSEC2_FLAGS			TSEC_GIGABIT
+#define TSEC2_PHYIDX			0
+#endif
+
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME			"TSEC1"
+
+/*
+ * Configure on-board RTC
+ */
+#define CONFIG_RTC_DS1337
+#define CONFIG_SYS_I2C_RTC_ADDR		0x68
+
+/*
+ * Environment
+ */
+#if defined(CONFIG_NAND_U_BOOT)
+	#define CONFIG_ENV_IS_IN_NAND		1
+	#define CONFIG_ENV_OFFSET		(768 * 1024)
+	#define CONFIG_ENV_SECT_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
+	#define CONFIG_ENV_SIZE			CONFIG_ENV_SECT_SIZE
+	#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
+	#define CONFIG_ENV_RANGE		(CONFIG_ENV_SECT_SIZE * 4)
+	#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
+#elif !defined(CONFIG_SYS_RAMBOOT)
+	#define CONFIG_ENV_IS_IN_FLASH		1
+	#define CONFIG_ENV_ADDR			(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+	#define CONFIG_ENV_SECT_SIZE		0x10000	/* 64K(one sector) for env */
+	#define CONFIG_ENV_SIZE			0x2000
+
+/* Address and size of Redundant Environment Sector */
+#else
+	#define CONFIG_ENV_IS_NOWHERE		1	/* Store ENV in memory only */
+	#define CONFIG_ENV_ADDR			(CONFIG_SYS_MONITOR_BASE - 0x1000)
+	#define CONFIG_ENV_SIZE			0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO			1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE		1	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_FLASH
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_JFFS2
+
+#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
+	#undef CONFIG_CMD_ENV
+	#undef CONFIG_CMD_LOADS
+#endif
+
+#define CONFIG_CMDLINE_EDITING		1
+
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP				/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR		0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT		"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size */
+
+#define CONFIG_SYS_PBSIZE		( CONFIG_SYS_CBSIZE		\
+					+ sizeof(CONFIG_SYS_PROMPT)	\
+					+ 16 )	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ			1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux*/
+
+#define CONFIG_SYS_RCWH_PCIHOST		0x80000000	/* PCIHOST */
+
+#define CONFIG_SYS_HRCW_LOW		( HRCWL_LCL_BUS_TO_SCB_CLK_1X1	\
+					| 0x20000000 /* reserved */	\
+					| HRCWL_DDR_TO_SCB_CLK_2X1	\
+					| HRCWL_CSB_TO_CLKIN_4X1	\
+					| HRCWL_CORE_TO_CSB_2_5X1 )
+
+#define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 4)
+
+#define CONFIG_SYS_HRCW_HIGH_BASE	( HRCWH_PCI_HOST		\
+					| HRCWH_PCI1_ARBITER_ENABLE	\
+					| HRCWH_CORE_ENABLE		\
+					| HRCWH_BOOTSEQ_DISABLE		\
+					| HRCWH_SW_WATCHDOG_DISABLE	\
+					| HRCWH_TSEC1M_IN_RGMII		\
+					| HRCWH_TSEC2M_IN_RGMII		\
+					| HRCWH_BIG_ENDIAN		\
+					| HRCWH_LALE_NORMAL )
+
+#ifdef CONFIG_NAND_LP
+#define CONFIG_SYS_HRCW_HIGH	( CONFIG_SYS_HRCW_HIGH_BASE		\
+				| HRCWH_FROM_0XFFF00100			\
+				| HRCWH_ROM_LOC_NAND_LP_8BIT		\
+				| HRCWH_RL_EXT_NAND)
+#else
+#define CONFIG_SYS_HRCW_HIGH	( CONFIG_SYS_HRCW_HIGH_BASE		\
+				| HRCWH_FROM_0XFFF00100			\
+				| HRCWH_ROM_LOC_NAND_SP_8BIT		\
+				| HRCWH_RL_EXT_NAND )
+#endif
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH	( SICRH_ETSEC2_B	\
+				| SICRH_ETSEC2_C	\
+				| SICRH_ETSEC2_D	\
+				| SICRH_ETSEC2_E	\
+				| SICRH_ETSEC2_F	\
+				| SICRH_ETSEC2_G	\
+				| SICRH_TSOBI1		\
+				| SICRH_TSOBI2 )
+#define CONFIG_SYS_SICRL	(SICRL_USBDR		\
+				| SICRL_ETSEC2_A )
+
+#define CONFIG_SYS_HID0_INIT	0x000000000
+#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK	\
+				| HID0_ENABLE_DYNAMIC_POWER_MANAGMENT )
+
+#define CONFIG_SYS_HID2		HID2_HBE
+
+#define CONFIG_HIGH_BATS	1	/* High BATs supported */
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L	((CONFIG_SYS_SDRAM_BASE + 0x10000000) | BATL_PP_10)
+#define CONFIG_SYS_IBAT1U	((CONFIG_SYS_SDRAM_BASE + 0x10000000) | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* PCI @ 0x80000000 */
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* PCI2 not supported on 8313 */
+#define CONFIG_SYS_IBAT4L	(0)
+#define CONFIG_SYS_IBAT4U	(0)
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
+#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CONFIG_SYS_IBAT6L	(0xF0000000 | BATL_PP_10)
+#define CONFIG_SYS_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CONFIG_SYS_IBAT7L	(0)
+#define CONFIG_SYS_IBAT7U	(0)
+
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
+#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
+#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02	/* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_NETDEV		eth1
+
+#define CONFIG_HOSTNAME		simpc8313
+#define CONFIG_ROOTPATH		/tftpboot/
+#define CONFIG_BOOTFILE		/tftpboot/uImage
+#define CONFIG_UBOOTPATH	u-boot-nand.bin	/* U-Boot image on TFTP server */
+#define CONFIG_FDTFILE		simpc8313.dtb
+
+#define CONFIG_LOADADDR		500000	/* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY	5	/* 5 second delay */
+#define CONFIG_BAUDRATE		115200
+
+#define CONFIG_BOOTCOMMAND	"nand read $loadaddr kernel 600000;bootm $loadaddr - $fdtaddr"
+
+#define XMK_STR(x)	#x
+#define MK_STR(x)	XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"netdev=" MK_STR(CONFIG_NETDEV) "\0"				\
+	"ethprime=TSEC1\0"						\
+	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+	"tftpflash=tftpboot $loadaddr $uboot; "				\
+		"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
+		"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
+		"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
+		"protect on " MK_STR(TEXT_BASE) " +$filesize; "		\
+		"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
+	"fdtaddr=ae0000\0"						\
+	"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0"				\
+	"console=ttyS0\0"						\
+	"setbootargs=setenv bootargs "					\
+		"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
+	"setipargs=setenv bootargs nfsroot=$serverip:$rootpath "	 \
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+		"root=$rootdev rw console=$console,$baudrate $othbootargs\0"	\
+	"load_uboot=tftp 100000 u-boot-nand.bin\0"			\
+	"burn_uboot=nand erase u-boot 80000; "				\
+		"nand write 100000 u-boot $filesize\0"			\
+	"update_uboot=run load_uboot;run burn_uboot\0"			\
+	"mtdids=nand0=nand0\0"						\
+	"mtdparts=mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)\0"	\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"	\
+	"bootargs=root=/dev/mtdblock2 rootfstype=jffs2 rw "		\
+		"console=ttyS0,115200\0"				\
+	""
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv rootdev /dev/nfs;"					\
+	"run setbootargs;"						\
+	"run setipargs;"						\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND						\
+	"setenv rootdev /dev/ram;"					\
+	"run setbootargs;"						\
+	"tftp $ramdiskaddr $ramdiskfile;"				\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif	/* __CONFIG_H */
diff --git a/include/mpc83xx.h b/include/mpc83xx.h
index 43553f5..191488a 100644
--- a/include/mpc83xx.h
+++ b/include/mpc83xx.h
@@ -751,9 +751,6 @@
 #define SCCR_USBDRCM_2			0x00800000
 #define SCCR_USBDRCM_3			0x00c00000
 
-#define SCCR_PCIEXP1CM			0x00300000
-#define SCCR_PCIEXP2CM			0x000c0000
-
 #define SCCR_SATA1CM			0x00003000
 #define SCCR_SATA1CM_SHIFT		12
 #define SCCR_SATACM			0x00003c00
@@ -800,6 +797,17 @@
 #define SCCR_USBDRCM_2			0x00800000
 #define SCCR_USBDRCM_3			0x00c00000
 
+/* All of the four SATA controllers must have the same clock ratio */
+#define SCCR_SATA1CM			0x000000c0
+#define SCCR_SATA1CM_SHIFT		6
+#define SCCR_SATACM			0x000000ff
+#define SCCR_SATACM_SHIFT		0
+#define SCCR_SATACM_0			0x00000000
+#define SCCR_SATACM_1			0x00000055
+#define SCCR_SATACM_2			0x000000aa
+#define SCCR_SATACM_3			0x000000ff
+#endif
+
 #define SCCR_PCIEXP1CM			0x00300000
 #define SCCR_PCIEXP1CM_SHIFT		20
 #define SCCR_PCIEXP1CM_0		0x00000000
@@ -814,17 +822,6 @@
 #define SCCR_PCIEXP2CM_2		0x00080000
 #define SCCR_PCIEXP2CM_3		0x000c0000
 
-/* All of the four SATA controllers must have the same clock ratio */
-#define SCCR_SATA1CM			0x000000c0
-#define SCCR_SATA1CM_SHIFT		6
-#define SCCR_SATACM			0x000000ff
-#define SCCR_SATACM_SHIFT		0
-#define SCCR_SATACM_0			0x00000000
-#define SCCR_SATACM_1			0x00000055
-#define SCCR_SATACM_2			0x000000aa
-#define SCCR_SATACM_3			0x000000ff
-#endif
-
 /* CSn_BDNS - Chip Select memory Bounds Register
  */
 #define CSBNDS_SA			0x00FF0000
@@ -1170,9 +1167,52 @@
 #define DDRCDR_M_ODR		0x00000002
 #define DDRCDR_Q_DRN		0x00000001
 
+/* PCIE Bridge Register
+*/
+#define PEX_CSB_CTRL_OBPIOE	0x00000001
+#define PEX_CSB_CTRL_IBPIOE	0x00000002
+#define PEX_CSB_CTRL_WDMAE	0x00000004
+#define PEX_CSB_CTRL_RDMAE	0x00000008
+
+#define PEX_CSB_OBCTRL_PIOE	0x00000001
+#define PEX_CSB_OBCTRL_MEMWE	0x00000002
+#define PEX_CSB_OBCTRL_IOWE	0x00000004
+#define PEX_CSB_OBCTRL_CFGWE	0x00000008
+
+#define PEX_CSB_IBCTRL_PIOE	0x00000001
+
+#define PEX_OWAR_EN		0x00000001
+#define PEX_OWAR_TYPE_CFG	0x00000000
+#define PEX_OWAR_TYPE_IO	0x00000002
+#define PEX_OWAR_TYPE_MEM	0x00000004
+#define PEX_OWAR_RLXO		0x00000008
+#define PEX_OWAR_NANP		0x00000010
+#define PEX_OWAR_SIZE		0xFFFFF000
+
+#define PEX_IWAR_EN		0x00000001
+#define PEX_IWAR_TYPE_INT	0x00000000
+#define PEX_IWAR_TYPE_PF	0x00000004
+#define PEX_IWAR_TYPE_NO_PF	0x00000006
+#define PEX_IWAR_NSOV		0x00000008
+#define PEX_IWAR_NSNP		0x00000010
+#define PEX_IWAR_SIZE		0xFFFFF000
+#define PEX_IWAR_SIZE_1M	0x000FF000
+#define PEX_IWAR_SIZE_2M	0x001FF000
+#define PEX_IWAR_SIZE_4M	0x003FF000
+#define PEX_IWAR_SIZE_8M	0x007FF000
+#define PEX_IWAR_SIZE_16M	0x00FFF000
+#define PEX_IWAR_SIZE_32M	0x01FFF000
+#define PEX_IWAR_SIZE_64M	0x03FFF000
+#define PEX_IWAR_SIZE_128M	0x07FFF000
+#define PEX_IWAR_SIZE_256M	0x0FFFF000
+
+#define PEX_GCLK_RATIO		0x440
+
 #ifndef __ASSEMBLY__
 struct pci_region;
 void mpc83xx_pci_init(int num_buses, struct pci_region **reg, int warmboot);
+void mpc83xx_pcislave_unlock(int bus);
+void mpc83xx_pcie_init(int num_buses, struct pci_region **reg, int warmboot);
 #endif
 
 #endif	/* __MPC83XX_H__ */
diff --git a/include/pci.h b/include/pci.h
index eebe8a8..072273b 100644
--- a/include/pci.h
+++ b/include/pci.h
@@ -382,6 +382,8 @@ extern void pci_cfgfunc_config_device(struct pci_controller* hose, pci_dev_t dev
 
 #define MAX_PCI_REGIONS		7
 
+#define INDIRECT_TYPE_NO_PCIE_LINK	1
+
 /*
  * Structure of a PCI controller (host bridge)
  */
@@ -394,6 +396,8 @@ struct pci_controller {
 	volatile unsigned int *cfg_addr;
 	volatile unsigned char *cfg_data;
 
+	int indirect_type;
+
 	struct pci_region regions[MAX_PCI_REGIONS];
 	int region_count;
 
diff --git a/nand_spl/board/sheldon/simpc8313/Makefile b/nand_spl/board/sheldon/simpc8313/Makefile
new file mode 100644
index 0000000..b0967a3
--- /dev/null
+++ b/nand_spl/board/sheldon/simpc8313/Makefile
@@ -0,0 +1,100 @@
+#
+# (C) Copyright 2007
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+# (C) Copyright 2008 Freescale Semiconductor
+# (C) Copyright Sheldon Instruments, Inc. 2008
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+NAND_SPL := y
+TEXT_BASE := 0xfff00000
+
+include $(TOPDIR)/config.mk
+
+LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds
+LDFLAGS	= -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS)
+AFLAGS	+= -DCONFIG_NAND_SPL
+CFLAGS	+= -DCONFIG_NAND_SPL
+
+SOBJS	= start.o ticks.o
+COBJS	= nand_boot_fsl_elbc.o $(BOARD).o sdram.o ns16550.o nand_init.o time.o
+
+SRCS	:= $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS	:= $(SOBJS) $(COBJS)
+LNDIR	:= $(OBJTREE)/nand_spl/board/$(BOARDDIR)
+
+nandobj	:= $(OBJTREE)/nand_spl/
+
+ALL	= $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+
+all:	$(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin:	$(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
+
+$(nandobj)u-boot-spl.bin:	$(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl:	$(OBJS)
+	cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
+		-Map $(nandobj)u-boot-spl.map \
+		-o $(nandobj)u-boot-spl
+
+# create symbolic links for common files
+
+$(obj)start.S:
+	ln -sf $(SRCTREE)/cpu/mpc83xx/start.S $<
+
+$(obj)nand_boot_fsl_elbc.c:
+	ln -sf $(SRCTREE)/nand_spl/nand_boot_fsl_elbc.c $<
+
+$(obj)sdram.c:
+	ln -sf $(SRCTREE)/board/$(BOARDDIR)/sdram.c $<
+
+$(obj)$(BOARD).c:
+	ln -sf $(SRCTREE)/board/$(BOARDDIR)/$(BOARD).c $<
+
+$(obj)ns16550.c:
+	ln -sf $(SRCTREE)/drivers/serial/ns16550.c $<
+
+$(obj)nand_init.c:
+	ln -sf $(SRCTREE)/cpu/mpc83xx/nand_init.c $<
+
+$(obj)time.c:
+	ln -sf $(SRCTREE)/lib_ppc/time.c $<
+
+$(obj)ticks.S:
+	ln -sf $(SRCTREE)/lib_ppc/ticks.S $<
+
+#########################################################################
+
+$(obj)%.o:	$(obj)%.S
+	$(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o:	$(obj)%.c
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/nand_spl/board/sheldon/simpc8313/u-boot.lds b/nand_spl/board/sheldon/simpc8313/u-boot.lds
new file mode 100644
index 0000000..40c4145
--- /dev/null
+++ b/nand_spl/board/sheldon/simpc8313/u-boot.lds
@@ -0,0 +1,52 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SECTIONS
+{
+	. = 0xfff00000;
+	.text : {
+		*(.text*)
+		. = ALIGN(16);
+		*(.rodata*)
+		*(.eh_frame)
+	}
+
+	. = ALIGN(8);
+	.data : {
+		*(.data*)
+		*(.sdata*)
+		_GOT2_TABLE_ = .;
+		*(.got2)
+		__got2_entries = (. - _GOT2_TABLE_) >> 2;
+	}
+
+	. = ALIGN(8);
+	__bss_start = .;
+	.bss (NOLOAD) : { *(.*bss) }
+	_end = .;
+}
+ENTRY(_start)
+ASSERT(_end <= 0xfff01000, "NAND bootstrap too big");