clk: clk_stm32f: Move SYSCFG clock setup into configure_clocks()

Move SYSCFG clock setup into configure_clocks() instead of calling
clock_setup() from board file.

As this clock is only needed in case of ethernet enabled and as
both stm32f4 and stm32f7 are using the Designware ethernet IP,
we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed.

Move the RMII setup from board_early_init_f() to board_init()
to insure that RMII bit is set only when clock driver is initialized.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

arch/arm/include/asm/arch-stm32f7/stm32_periph.h

@@ -21,7 +21,6 @@ enum periph_id {
 };
 
 enum periph_clock {
-	SYSCFG_CLOCK_CFG,
 	TIMER2_CLOCK_CFG,
 };
 

board/st/stm32f746-disco/stm32f746-disco.c

@@ -69,23 +69,10 @@ int dram_init_banksize(void)
 	return 0;
 }
 
-#ifdef CONFIG_ETH_DESIGNWARE
-static int stmmac_setup(void)
-{
-	clock_setup(SYSCFG_CLOCK_CFG);
-	/* Set >RMII mode */
-	STM32_SYSCFG->pmc |= SYSCFG_PMC_MII_RMII_SEL;
-
-	return 0;
-}
-
 int board_early_init_f(void)
 {
-	stmmac_setup();
-
 	return 0;
 }
-#endif
 
 #ifdef CONFIG_SPL_BUILD
 #ifdef CONFIG_SPL_OS_BOOT
@@ -162,5 +149,11 @@ int board_late_init(void)
 int board_init(void)
 {
 	gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
+
+#ifdef CONFIG_ETH_DESIGNWARE
+	/* Set >RMII mode */
+	STM32_SYSCFG->pmc |= SYSCFG_PMC_MII_RMII_SEL;
+#endif
+
 	return 0;
 }

drivers/clk/clk_stm32f.c

@@ -67,8 +67,6 @@
 #define RCC_DCKCFGRX_SDMMC1SEL		BIT(28)
 #define RCC_DCKCFGR2_SDMMC2SEL		BIT(29)
 
-#define RCC_APB2ENR_SAI1EN		BIT(22)
-
 /*
  * RCC AHB1ENR specific definitions
  */
@@ -86,9 +84,9 @@
  * RCC APB2ENR specific definitions
  */
 #define RCC_APB2ENR_SYSCFGEN		BIT(14)
+#define RCC_APB2ENR_SAI1EN		BIT(22)
 
 enum periph_clock {
-	SYSCFG_CLOCK_CFG,
 	TIMER2_CLOCK_CFG,
 };
 
@@ -226,6 +224,11 @@ static int configure_clocks(struct udevice *dev)
 	/* gate the SAI clock, needed for MMC 1&2 clocks */
 	setbits_le32(&regs->apb2enr, RCC_APB2ENR_SAI1EN);
 
+#ifdef CONFIG_ETH_DESIGNWARE
+	/* gate the SYSCFG clock, needed to set RMII ethernet interface */
+	setbits_le32(&regs->apb2enr, RCC_APB2ENR_SYSCFGEN);
+#endif
+
 	return 0;
 }
 
@@ -351,9 +354,6 @@ static int stm32_clk_enable(struct clk *clk)
 void clock_setup(int peripheral)
 {
 	switch (peripheral) {
-	case SYSCFG_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->apb2enr, RCC_APB2ENR_SYSCFGEN);
-		break;
 	case TIMER2_CLOCK_CFG:
 		setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_TIM2EN);
 		break;