Merge git://git.denx.de/u-boot-socfpga

arch/arm/dts/socfpga_cyclone5_socdk.dts

@@ -89,7 +89,7 @@
 		#size-cells = <1>;
 		compatible = "n25q00";
 		reg = <0>;      /* chip select */
-		spi-max-frequency = <50000000>;
+		spi-max-frequency = <100000000>;
 		m25p,fast-read;
 		page-size = <256>;
 		block-size = <16>; /* 2^16, 64KB */

arch/arm/mach-socfpga/include/mach/reset_manager.h

@@ -69,9 +69,9 @@ struct socfpga_reset_manager {
 #define RSTMGR_UART0		RSTMGR_DEFINE(1, 16)
 #define RSTMGR_SPIM0		RSTMGR_DEFINE(1, 18)
 #define RSTMGR_SPIM1		RSTMGR_DEFINE(1, 19)
-#define RSTMGR_QSPI		RSTMGR_DEFINE(0, 5)
-#define RSTMGR_SDMMC		RSTMGR_DEFINE(0, 22)
-#define RSTMGR_DMA		RSTMGR_DEFINE(0, 28)
+#define RSTMGR_QSPI		RSTMGR_DEFINE(1, 5)
+#define RSTMGR_SDMMC		RSTMGR_DEFINE(1, 22)
+#define RSTMGR_DMA		RSTMGR_DEFINE(1, 28)
 #define RSTMGR_SDR		RSTMGR_DEFINE(1, 29)
 
 /* Create a human-readable reference to SoCFPGA reset. */

drivers/spi/cadence_qspi.c

@@ -37,9 +37,8 @@ static int cadence_spi_write_speed(struct udevice *bus, uint hz)
 }
 
 /* Calibration sequence to determine the read data capture delay register */
-static int spi_calibration(struct udevice *bus)
+static int spi_calibration(struct udevice *bus, uint hz)
 {
-	struct cadence_spi_platdata *plat = bus->platdata;
 	struct cadence_spi_priv *priv = dev_get_priv(bus);
 	void *base = priv->regbase;
 	u8 opcode_rdid = 0x9F;
@@ -64,7 +63,7 @@ static int spi_calibration(struct udevice *bus)
 	}
 
 	/* use back the intended clock and find low range */
-	cadence_spi_write_speed(bus, plat->max_hz);
+	cadence_spi_write_speed(bus, hz);
 	for (i = 0; i < CQSPI_READ_CAPTURE_MAX_DELAY; i++) {
 		/* Disable QSPI */
 		cadence_qspi_apb_controller_disable(base);
@@ -111,7 +110,7 @@ static int spi_calibration(struct udevice *bus)
 	      (range_hi + range_lo) / 2, range_lo, range_hi);
 
 	/* just to ensure we do once only when speed or chip select change */
-	priv->qspi_calibrated_hz = plat->max_hz;
+	priv->qspi_calibrated_hz = hz;
 	priv->qspi_calibrated_cs = spi_chip_select(bus);
 
 	return 0;
@@ -123,17 +122,25 @@ static int cadence_spi_set_speed(struct udevice *bus, uint hz)
 	struct cadence_spi_priv *priv = dev_get_priv(bus);
 	int err;
 
+	if (hz > plat->max_hz)
+		hz = plat->max_hz;
+
 	/* Disable QSPI */
 	cadence_qspi_apb_controller_disable(priv->regbase);
 
-	cadence_spi_write_speed(bus, hz);
-
-	/* Calibration required for different SCLK speed or chip select */
-	if (priv->qspi_calibrated_hz != plat->max_hz ||
+	/*
+	 * Calibration required for different current SCLK speed, requested
+	 * SCLK speed or chip select
+	 */
+	if (priv->previous_hz != hz ||
+	    priv->qspi_calibrated_hz != hz ||
 	    priv->qspi_calibrated_cs != spi_chip_select(bus)) {
-		err = spi_calibration(bus);
+		err = spi_calibration(bus, hz);
 		if (err)
 			return err;
+
+		/* prevent calibration run when same as previous request */
+		priv->previous_hz = hz;
 	}
 
 	/* Enable QSPI */
@@ -291,10 +298,6 @@ static int cadence_spi_ofdata_to_platdata(struct udevice *bus)
 	plat->regbase = (void *)data[0];
 	plat->ahbbase = (void *)data[2];
 
-	/* Use 500KHz as a suitable default */
-	plat->max_hz = fdtdec_get_int(blob, node, "spi-max-frequency",
-				      500000);
-
 	/* All other paramters are embedded in the child node */
 	subnode = fdt_first_subnode(blob, node);
 	if (subnode < 0) {
@@ -302,6 +305,10 @@ static int cadence_spi_ofdata_to_platdata(struct udevice *bus)
 		return -ENODEV;
 	}
 
+	/* Use 500 KHz as a suitable default */
+	plat->max_hz = fdtdec_get_uint(blob, subnode, "spi-max-frequency",
+				       500000);
+
 	/* Read other parameters from DT */
 	plat->page_size = fdtdec_get_int(blob, subnode, "page-size", 256);
 	plat->block_size = fdtdec_get_int(blob, subnode, "block-size", 16);

drivers/spi/cadence_qspi.h

@@ -38,6 +38,7 @@ struct cadence_spi_priv {
 	int		qspi_is_init;
 	unsigned int	qspi_calibrated_hz;
 	unsigned int	qspi_calibrated_cs;
+	unsigned int	previous_hz;
 };
 
 /* Functions call declaration */

include/fdtdec.h

@@ -490,6 +490,19 @@ s32 fdtdec_get_int(const void *blob, int node, const char *prop_name,
 		s32 default_val);
 
 /**
+ * Unsigned version of fdtdec_get_int. The property must have at least
+ * 4 bytes of data. The value of the first cell is returned.
+ *
+ * @param blob	FDT blob
+ * @param node	node to examine
+ * @param prop_name	name of property to find
+ * @param default_val	default value to return if the property is not found
+ * @return unsigned integer value, if found, or default_val if not
+ */
+unsigned int fdtdec_get_uint(const void *blob, int node, const char *prop_name,
+			unsigned int default_val);
+
+/**
  * Get a variable-sized number from a property
  *
  * This reads a number from one or more cells.

lib/fdtdec_common.c

@@ -36,3 +36,21 @@ int fdtdec_get_int(const void *blob, int node, const char *prop_name,
 	debug("(not found)\n");
 	return default_val;
 }
+
+unsigned int fdtdec_get_uint(const void *blob, int node, const char *prop_name,
+			unsigned int default_val)
+{
+	const int *cell;
+	int len;
+
+	debug("%s: %s: ", __func__, prop_name);
+	cell = fdt_getprop(blob, node, prop_name, &len);
+	if (cell && len >= sizeof(unsigned int)) {
+		unsigned int val = fdt32_to_cpu(cell[0]);
+
+		debug("%#x (%d)\n", val, val);
+		return val;
+	}
+	debug("(not found)\n");
+	return default_val;
+}