diff --git a/drivers/ddr/altera/Makefile b/drivers/ddr/altera/Makefile new file mode 100644 index 0000000..1ca7058 --- /dev/null +++ b/drivers/ddr/altera/Makefile @@ -0,0 +1,11 @@ +# +# (C) Copyright 2000-2003 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# (C) Copyright 2010, Thomas Chou +# Copyright (C) 2014 Altera Corporation +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-$(CONFIG_ALTERA_SDRAM) += sdram.o sequencer.o diff --git a/drivers/ddr/altera/sequencer.c b/drivers/ddr/altera/sequencer.c new file mode 100644 index 0000000..6340859 --- /dev/null +++ b/drivers/ddr/altera/sequencer.c @@ -0,0 +1,4051 @@ +/* + * Copyright Altera Corporation (C) 2012-2015 + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#include +#include +#include +#include "sequencer.h" +#include "sequencer_auto.h" +#include "sequencer_auto_ac_init.h" +#include "sequencer_auto_inst_init.h" +#include "sequencer_defines.h" + +static void scc_mgr_load_dqs_for_write_group(uint32_t write_group); + +static struct socfpga_sdr_rw_load_manager *sdr_rw_load_mgr_regs = + (struct socfpga_sdr_rw_load_manager *)(BASE_RW_MGR + 0x800); + +static struct socfpga_sdr_rw_load_jump_manager *sdr_rw_load_jump_mgr_regs = + (struct socfpga_sdr_rw_load_jump_manager *)(BASE_RW_MGR + 0xC00); + +static struct socfpga_sdr_reg_file *sdr_reg_file = + (struct socfpga_sdr_reg_file *)(BASE_REG_FILE); + +static struct socfpga_sdr_scc_mgr *sdr_scc_mgr = + (struct socfpga_sdr_scc_mgr *)(BASE_SCC_MGR + 0x0E00); + +static struct socfpga_phy_mgr_cmd *phy_mgr_cmd = + (struct socfpga_phy_mgr_cmd *)(BASE_PHY_MGR); + +static struct socfpga_phy_mgr_cfg *phy_mgr_cfg = + (struct socfpga_phy_mgr_cfg *)(BASE_PHY_MGR + 0x4000); + +static struct socfpga_data_mgr *data_mgr = + (struct socfpga_data_mgr *)(BASE_DATA_MGR); + +#define DELTA_D 1 +#define MGR_SELECT_MASK 0xf8000 + +/* + * In order to reduce ROM size, most of the selectable calibration steps are + * decided at compile time based on the user's calibration mode selection, + * as captured by the STATIC_CALIB_STEPS selection below. + * + * However, to support simulation-time selection of fast simulation mode, where + * we skip everything except the bare minimum, we need a few of the steps to + * be dynamic. In those cases, we either use the DYNAMIC_CALIB_STEPS for the + * check, which is based on the rtl-supplied value, or we dynamically compute + * the value to use based on the dynamically-chosen calibration mode + */ + +#define DLEVEL 0 +#define STATIC_IN_RTL_SIM 0 +#define STATIC_SKIP_DELAY_LOOPS 0 + +#define STATIC_CALIB_STEPS (STATIC_IN_RTL_SIM | CALIB_SKIP_FULL_TEST | \ + STATIC_SKIP_DELAY_LOOPS) + +/* calibration steps requested by the rtl */ +uint16_t dyn_calib_steps; + +/* + * To make CALIB_SKIP_DELAY_LOOPS a dynamic conditional option + * instead of static, we use boolean logic to select between + * non-skip and skip values + * + * The mask is set to include all bits when not-skipping, but is + * zero when skipping + */ + +uint16_t skip_delay_mask; /* mask off bits when skipping/not-skipping */ + +#define SKIP_DELAY_LOOP_VALUE_OR_ZERO(non_skip_value) \ + ((non_skip_value) & skip_delay_mask) + +struct gbl_type *gbl; +struct param_type *param; +uint32_t curr_shadow_reg; + +static uint32_t rw_mgr_mem_calibrate_write_test(uint32_t rank_bgn, + uint32_t write_group, uint32_t use_dm, + uint32_t all_correct, uint32_t *bit_chk, uint32_t all_ranks); + +static u32 sdr_get_addr(u32 *base) +{ + u32 addr = (u32)base & MGR_SELECT_MASK; + + switch (addr) { + case BASE_PHY_MGR: + addr = (((u32)base >> 8) & (1 << 6)) | ((u32)base & 0x3f) | + SDR_PHYGRP_PHYMGRGRP_ADDRESS; + break; + case BASE_RW_MGR: + addr = ((u32)base & 0x1fff) | SDR_PHYGRP_RWMGRGRP_ADDRESS; + break; + case BASE_DATA_MGR: + addr = ((u32)base & 0x7ff) | SDR_PHYGRP_DATAMGRGRP_ADDRESS; + break; + case BASE_SCC_MGR: + addr = ((u32)base & 0xfff) | SDR_PHYGRP_SCCGRP_ADDRESS; + break; + case BASE_REG_FILE: + addr = ((u32)base & 0x7ff) | SDR_PHYGRP_REGFILEGRP_ADDRESS; + break; + case BASE_MMR: + addr = ((u32)base & 0xfff) | SDR_CTRLGRP_ADDRESS; + break; + default: + return -1; + } + + return addr; +} + +static void set_failing_group_stage(uint32_t group, uint32_t stage, + uint32_t substage) +{ + /* + * Only set the global stage if there was not been any other + * failing group + */ + if (gbl->error_stage == CAL_STAGE_NIL) { + gbl->error_substage = substage; + gbl->error_stage = stage; + gbl->error_group = group; + } +} + +static void reg_file_set_group(uint32_t set_group) +{ + u32 addr = sdr_get_addr(&sdr_reg_file->cur_stage); + + /* Read the current group and stage */ + uint32_t cur_stage_group = readl(SOCFPGA_SDR_ADDRESS + addr); + + /* Clear the group */ + cur_stage_group &= 0x0000FFFF; + + /* Set the group */ + cur_stage_group |= (set_group << 16); + + /* Write the data back */ + writel(cur_stage_group, SOCFPGA_SDR_ADDRESS + addr); +} + +static void reg_file_set_stage(uint32_t set_stage) +{ + u32 addr = sdr_get_addr(&sdr_reg_file->cur_stage); + /* Read the current group and stage */ + uint32_t cur_stage_group = readl(SOCFPGA_SDR_ADDRESS + addr); + + /* Clear the stage and substage */ + cur_stage_group &= 0xFFFF0000; + + /* Set the stage */ + cur_stage_group |= (set_stage & 0x000000FF); + + /* Write the data back */ + writel(cur_stage_group, SOCFPGA_SDR_ADDRESS + addr); +} + +static void reg_file_set_sub_stage(uint32_t set_sub_stage) +{ + u32 addr = sdr_get_addr(&sdr_reg_file->cur_stage); + /* Read the current group and stage */ + uint32_t cur_stage_group = readl(SOCFPGA_SDR_ADDRESS + addr); + + /* Clear the substage */ + cur_stage_group &= 0xFFFF00FF; + + /* Set the sub stage */ + cur_stage_group |= ((set_sub_stage << 8) & 0x0000FF00); + + /* Write the data back */ + writel(cur_stage_group, SOCFPGA_SDR_ADDRESS + addr); +} + +static void initialize(void) +{ + u32 addr = sdr_get_addr(&phy_mgr_cfg->mux_sel); + + debug("%s:%d\n", __func__, __LINE__); + /* USER calibration has control over path to memory */ + /* + * In Hard PHY this is a 2-bit control: + * 0: AFI Mux Select + * 1: DDIO Mux Select + */ + writel(0x3, SOCFPGA_SDR_ADDRESS + addr); + + /* USER memory clock is not stable we begin initialization */ + addr = sdr_get_addr(&phy_mgr_cfg->reset_mem_stbl); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* USER calibration status all set to zero */ + addr = sdr_get_addr(&phy_mgr_cfg->cal_status); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&phy_mgr_cfg->cal_debug_info); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + if ((dyn_calib_steps & CALIB_SKIP_ALL) != CALIB_SKIP_ALL) { + param->read_correct_mask_vg = ((uint32_t)1 << + (RW_MGR_MEM_DQ_PER_READ_DQS / + RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS)) - 1; + param->write_correct_mask_vg = ((uint32_t)1 << + (RW_MGR_MEM_DQ_PER_READ_DQS / + RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS)) - 1; + param->read_correct_mask = ((uint32_t)1 << + RW_MGR_MEM_DQ_PER_READ_DQS) - 1; + param->write_correct_mask = ((uint32_t)1 << + RW_MGR_MEM_DQ_PER_WRITE_DQS) - 1; + param->dm_correct_mask = ((uint32_t)1 << + (RW_MGR_MEM_DATA_WIDTH / RW_MGR_MEM_DATA_MASK_WIDTH)) + - 1; + } +} + +static void set_rank_and_odt_mask(uint32_t rank, uint32_t odt_mode) +{ + uint32_t odt_mask_0 = 0; + uint32_t odt_mask_1 = 0; + uint32_t cs_and_odt_mask; + uint32_t addr; + + if (odt_mode == RW_MGR_ODT_MODE_READ_WRITE) { + if (RW_MGR_MEM_NUMBER_OF_RANKS == 1) { + /* + * 1 Rank + * Read: ODT = 0 + * Write: ODT = 1 + */ + odt_mask_0 = 0x0; + odt_mask_1 = 0x1; + } else if (RW_MGR_MEM_NUMBER_OF_RANKS == 2) { + /* 2 Ranks */ + if (RW_MGR_MEM_NUMBER_OF_CS_PER_DIMM == 1) { + /* - Dual-Slot , Single-Rank + * (1 chip-select per DIMM) + * OR + * - RDIMM, 4 total CS (2 CS per DIMM) + * means 2 DIMM + * Since MEM_NUMBER_OF_RANKS is 2 they are + * both single rank + * with 2 CS each (special for RDIMM) + * Read: Turn on ODT on the opposite rank + * Write: Turn on ODT on all ranks + */ + odt_mask_0 = 0x3 & ~(1 << rank); + odt_mask_1 = 0x3; + } else { + /* + * USER - Single-Slot , Dual-rank DIMMs + * (2 chip-selects per DIMM) + * USER Read: Turn on ODT off on all ranks + * USER Write: Turn on ODT on active rank + */ + odt_mask_0 = 0x0; + odt_mask_1 = 0x3 & (1 << rank); + } + } else { + /* 4 Ranks + * Read: + * ----------+-----------------------+ + * | | + * | ODT | + * Read From +-----------------------+ + * Rank | 3 | 2 | 1 | 0 | + * ----------+-----+-----+-----+-----+ + * 0 | 0 | 1 | 0 | 0 | + * 1 | 1 | 0 | 0 | 0 | + * 2 | 0 | 0 | 0 | 1 | + * 3 | 0 | 0 | 1 | 0 | + * ----------+-----+-----+-----+-----+ + * + * Write: + * ----------+-----------------------+ + * | | + * | ODT | + * Write To +-----------------------+ + * Rank | 3 | 2 | 1 | 0 | + * ----------+-----+-----+-----+-----+ + * 0 | 0 | 1 | 0 | 1 | + * 1 | 1 | 0 | 1 | 0 | + * 2 | 0 | 1 | 0 | 1 | + * 3 | 1 | 0 | 1 | 0 | + * ----------+-----+-----+-----+-----+ + */ + switch (rank) { + case 0: + odt_mask_0 = 0x4; + odt_mask_1 = 0x5; + break; + case 1: + odt_mask_0 = 0x8; + odt_mask_1 = 0xA; + break; + case 2: + odt_mask_0 = 0x1; + odt_mask_1 = 0x5; + break; + case 3: + odt_mask_0 = 0x2; + odt_mask_1 = 0xA; + break; + } + } + } else { + odt_mask_0 = 0x0; + odt_mask_1 = 0x0; + } + + cs_and_odt_mask = + (0xFF & ~(1 << rank)) | + ((0xFF & odt_mask_0) << 8) | + ((0xFF & odt_mask_1) << 16); + addr = sdr_get_addr((u32 *)RW_MGR_SET_CS_AND_ODT_MASK); + writel(cs_and_odt_mask, SOCFPGA_SDR_ADDRESS + addr); +} + +static void scc_mgr_initialize(void) +{ + u32 addr = sdr_get_addr((u32 *)SCC_MGR_HHP_RFILE); + + /* + * Clear register file for HPS + * 16 (2^4) is the size of the full register file in the scc mgr: + * RFILE_DEPTH = log2(MEM_DQ_PER_DQS + 1 + MEM_DM_PER_DQS + + * MEM_IF_READ_DQS_WIDTH - 1) + 1; + */ + uint32_t i; + for (i = 0; i < 16; i++) { + debug_cond(DLEVEL == 1, "%s:%d: Clearing SCC RFILE index %u", + __func__, __LINE__, i); + writel(0, SOCFPGA_SDR_ADDRESS + addr + (i << 2)); + } +} + +static void scc_mgr_set_dqs_bus_in_delay(uint32_t read_group, + uint32_t delay) +{ + u32 addr = sdr_get_addr((u32 *)SCC_MGR_DQS_IN_DELAY); + + /* Load the setting in the SCC manager */ + writel(delay, SOCFPGA_SDR_ADDRESS + addr + (read_group << 2)); +} + +static void scc_mgr_set_dqs_io_in_delay(uint32_t write_group, + uint32_t delay) +{ + u32 addr = sdr_get_addr((u32 *)SCC_MGR_IO_IN_DELAY); + + writel(delay, SOCFPGA_SDR_ADDRESS + addr + (RW_MGR_MEM_DQ_PER_WRITE_DQS << 2)); +} + +static void scc_mgr_set_dqs_en_phase(uint32_t read_group, uint32_t phase) +{ + u32 addr = sdr_get_addr((u32 *)SCC_MGR_DQS_EN_PHASE); + + /* Load the setting in the SCC manager */ + writel(phase, SOCFPGA_SDR_ADDRESS + addr + (read_group << 2)); +} + +static void scc_mgr_set_dqs_en_phase_all_ranks(uint32_t read_group, + uint32_t phase) +{ + uint32_t r; + uint32_t update_scan_chains; + uint32_t addr; + + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; + r += NUM_RANKS_PER_SHADOW_REG) { + /* + * USER although the h/w doesn't support different phases per + * shadow register, for simplicity our scc manager modeling + * keeps different phase settings per shadow reg, and it's + * important for us to keep them in sync to match h/w. + * for efficiency, the scan chain update should occur only + * once to sr0. + */ + update_scan_chains = (r == 0) ? 1 : 0; + + scc_mgr_set_dqs_en_phase(read_group, phase); + + if (update_scan_chains) { + addr = sdr_get_addr(&sdr_scc_mgr->dqs_ena); + writel(read_group, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + } + } +} + +static void scc_mgr_set_dqdqs_output_phase(uint32_t write_group, + uint32_t phase) +{ + u32 addr = sdr_get_addr((u32 *)SCC_MGR_DQDQS_OUT_PHASE); + + /* Load the setting in the SCC manager */ + writel(phase, SOCFPGA_SDR_ADDRESS + addr + (write_group << 2)); +} + +static void scc_mgr_set_dqdqs_output_phase_all_ranks(uint32_t write_group, + uint32_t phase) +{ + uint32_t r; + uint32_t update_scan_chains; + uint32_t addr; + + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; + r += NUM_RANKS_PER_SHADOW_REG) { + /* + * USER although the h/w doesn't support different phases per + * shadow register, for simplicity our scc manager modeling + * keeps different phase settings per shadow reg, and it's + * important for us to keep them in sync to match h/w. + * for efficiency, the scan chain update should occur only + * once to sr0. + */ + update_scan_chains = (r == 0) ? 1 : 0; + + scc_mgr_set_dqdqs_output_phase(write_group, phase); + + if (update_scan_chains) { + addr = sdr_get_addr(&sdr_scc_mgr->dqs_ena); + writel(write_group, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + } + } +} + +static void scc_mgr_set_dqs_en_delay(uint32_t read_group, uint32_t delay) +{ + uint32_t addr = sdr_get_addr((u32 *)SCC_MGR_DQS_EN_DELAY); + + /* Load the setting in the SCC manager */ + writel(delay + IO_DQS_EN_DELAY_OFFSET, SOCFPGA_SDR_ADDRESS + addr + + (read_group << 2)); +} + +static void scc_mgr_set_dqs_en_delay_all_ranks(uint32_t read_group, + uint32_t delay) +{ + uint32_t r; + uint32_t addr; + + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; + r += NUM_RANKS_PER_SHADOW_REG) { + scc_mgr_set_dqs_en_delay(read_group, delay); + + addr = sdr_get_addr(&sdr_scc_mgr->dqs_ena); + writel(read_group, SOCFPGA_SDR_ADDRESS + addr); + /* + * In shadow register mode, the T11 settings are stored in + * registers in the core, which are updated by the DQS_ENA + * signals. Not issuing the SCC_MGR_UPD command allows us to + * save lots of rank switching overhead, by calling + * select_shadow_regs_for_update with update_scan_chains + * set to 0. + */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + } + /* + * In shadow register mode, the T11 settings are stored in + * registers in the core, which are updated by the DQS_ENA + * signals. Not issuing the SCC_MGR_UPD command allows us to + * save lots of rank switching overhead, by calling + * select_shadow_regs_for_update with update_scan_chains + * set to 0. + */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); +} + +static void scc_mgr_set_oct_out1_delay(uint32_t write_group, uint32_t delay) +{ + uint32_t read_group; + uint32_t addr = sdr_get_addr((u32 *)SCC_MGR_OCT_OUT1_DELAY); + + /* + * Load the setting in the SCC manager + * Although OCT affects only write data, the OCT delay is controlled + * by the DQS logic block which is instantiated once per read group. + * For protocols where a write group consists of multiple read groups, + * the setting must be set multiple times. + */ + for (read_group = write_group * RW_MGR_MEM_IF_READ_DQS_WIDTH / + RW_MGR_MEM_IF_WRITE_DQS_WIDTH; + read_group < (write_group + 1) * RW_MGR_MEM_IF_READ_DQS_WIDTH / + RW_MGR_MEM_IF_WRITE_DQS_WIDTH; ++read_group) + writel(delay, SOCFPGA_SDR_ADDRESS + addr + (read_group << 2)); +} + +static void scc_mgr_set_dq_out1_delay(uint32_t write_group, + uint32_t dq_in_group, uint32_t delay) +{ + uint32_t addr = sdr_get_addr((u32 *)SCC_MGR_IO_OUT1_DELAY); + + /* Load the setting in the SCC manager */ + writel(delay, SOCFPGA_SDR_ADDRESS + addr + (dq_in_group << 2)); +} + +static void scc_mgr_set_dq_in_delay(uint32_t write_group, + uint32_t dq_in_group, uint32_t delay) +{ + uint32_t addr = sdr_get_addr((u32 *)SCC_MGR_IO_IN_DELAY); + + /* Load the setting in the SCC manager */ + writel(delay, SOCFPGA_SDR_ADDRESS + addr + (dq_in_group << 2)); +} + +static void scc_mgr_set_hhp_extras(void) +{ + /* + * Load the fixed setting in the SCC manager + * bits: 0:0 = 1'b1 - dqs bypass + * bits: 1:1 = 1'b1 - dq bypass + * bits: 4:2 = 3'b001 - rfifo_mode + * bits: 6:5 = 2'b01 - rfifo clock_select + * bits: 7:7 = 1'b0 - separate gating from ungating setting + * bits: 8:8 = 1'b0 - separate OE from Output delay setting + */ + uint32_t value = (0<<8) | (0<<7) | (1<<5) | (1<<2) | (1<<1) | (1<<0); + uint32_t addr = sdr_get_addr((u32 *)SCC_MGR_HHP_GLOBALS); + + writel(value, SOCFPGA_SDR_ADDRESS + addr + SCC_MGR_HHP_EXTRAS_OFFSET); +} + +static void scc_mgr_set_dqs_out1_delay(uint32_t write_group, + uint32_t delay) +{ + uint32_t addr = sdr_get_addr((u32 *)SCC_MGR_IO_OUT1_DELAY); + + /* Load the setting in the SCC manager */ + writel(delay, SOCFPGA_SDR_ADDRESS + addr + (RW_MGR_MEM_DQ_PER_WRITE_DQS << 2)); +} + +static void scc_mgr_set_dm_out1_delay(uint32_t write_group, + uint32_t dm, uint32_t delay) +{ + uint32_t addr = sdr_get_addr((u32 *)SCC_MGR_IO_OUT1_DELAY); + + /* Load the setting in the SCC manager */ + writel(delay, SOCFPGA_SDR_ADDRESS + addr + + ((RW_MGR_MEM_DQ_PER_WRITE_DQS + 1 + dm) << 2)); +} + +/* + * USER Zero all DQS config + * TODO: maybe rename to scc_mgr_zero_dqs_config (or something) + */ +static void scc_mgr_zero_all(void) +{ + uint32_t i, r; + uint32_t addr; + + /* + * USER Zero all DQS config settings, across all groups and all + * shadow registers + */ + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; r += + NUM_RANKS_PER_SHADOW_REG) { + for (i = 0; i < RW_MGR_MEM_IF_READ_DQS_WIDTH; i++) { + /* + * The phases actually don't exist on a per-rank basis, + * but there's no harm updating them several times, so + * let's keep the code simple. + */ + scc_mgr_set_dqs_bus_in_delay(i, IO_DQS_IN_RESERVE); + scc_mgr_set_dqs_en_phase(i, 0); + scc_mgr_set_dqs_en_delay(i, 0); + } + + for (i = 0; i < RW_MGR_MEM_IF_WRITE_DQS_WIDTH; i++) { + scc_mgr_set_dqdqs_output_phase(i, 0); + /* av/cv don't have out2 */ + scc_mgr_set_oct_out1_delay(i, IO_DQS_OUT_RESERVE); + } + } + + /* multicast to all DQS group enables */ + addr = sdr_get_addr(&sdr_scc_mgr->dqs_ena); + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); +} + +static void scc_set_bypass_mode(uint32_t write_group, uint32_t mode) +{ + uint32_t addr; + /* mode = 0 : Do NOT bypass - Half Rate Mode */ + /* mode = 1 : Bypass - Full Rate Mode */ + + /* only need to set once for all groups, pins, dq, dqs, dm */ + if (write_group == 0) { + debug_cond(DLEVEL == 1, "%s:%d Setting HHP Extras\n", __func__, + __LINE__); + scc_mgr_set_hhp_extras(); + debug_cond(DLEVEL == 1, "%s:%d Done Setting HHP Extras\n", + __func__, __LINE__); + } + /* multicast to all DQ enables */ + addr = sdr_get_addr(&sdr_scc_mgr->dq_ena); + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_scc_mgr->dm_ena); + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + + /* update current DQS IO enable */ + addr = sdr_get_addr(&sdr_scc_mgr->dqs_io_ena); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* update the DQS logic */ + addr = sdr_get_addr(&sdr_scc_mgr->dqs_ena); + writel(write_group, SOCFPGA_SDR_ADDRESS + addr); + + /* hit update */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); +} + +static void scc_mgr_zero_group(uint32_t write_group, uint32_t test_begin, + int32_t out_only) +{ + uint32_t i, r; + uint32_t addr; + + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; r += + NUM_RANKS_PER_SHADOW_REG) { + /* Zero all DQ config settings */ + for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) { + scc_mgr_set_dq_out1_delay(write_group, i, 0); + if (!out_only) + scc_mgr_set_dq_in_delay(write_group, i, 0); + } + + /* multicast to all DQ enables */ + addr = sdr_get_addr(&sdr_scc_mgr->dq_ena); + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + + /* Zero all DM config settings */ + for (i = 0; i < RW_MGR_NUM_DM_PER_WRITE_GROUP; i++) { + scc_mgr_set_dm_out1_delay(write_group, i, 0); + } + + /* multicast to all DM enables */ + addr = sdr_get_addr(&sdr_scc_mgr->dm_ena); + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + + /* zero all DQS io settings */ + if (!out_only) + scc_mgr_set_dqs_io_in_delay(write_group, 0); + /* av/cv don't have out2 */ + scc_mgr_set_dqs_out1_delay(write_group, IO_DQS_OUT_RESERVE); + scc_mgr_set_oct_out1_delay(write_group, IO_DQS_OUT_RESERVE); + scc_mgr_load_dqs_for_write_group(write_group); + + /* multicast to all DQS IO enables (only 1) */ + addr = sdr_get_addr(&sdr_scc_mgr->dqs_io_ena); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* hit update to zero everything */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + } +} + +/* load up dqs config settings */ +static void scc_mgr_load_dqs(uint32_t dqs) +{ + uint32_t addr = sdr_get_addr(&sdr_scc_mgr->dqs_ena); + + writel(dqs, SOCFPGA_SDR_ADDRESS + addr); +} + +static void scc_mgr_load_dqs_for_write_group(uint32_t write_group) +{ + uint32_t read_group; + uint32_t addr = sdr_get_addr(&sdr_scc_mgr->dqs_ena); + /* + * Although OCT affects only write data, the OCT delay is controlled + * by the DQS logic block which is instantiated once per read group. + * For protocols where a write group consists of multiple read groups, + * the setting must be scanned multiple times. + */ + for (read_group = write_group * RW_MGR_MEM_IF_READ_DQS_WIDTH / + RW_MGR_MEM_IF_WRITE_DQS_WIDTH; + read_group < (write_group + 1) * RW_MGR_MEM_IF_READ_DQS_WIDTH / + RW_MGR_MEM_IF_WRITE_DQS_WIDTH; ++read_group) + writel(read_group, SOCFPGA_SDR_ADDRESS + addr); +} + +/* load up dqs io config settings */ +static void scc_mgr_load_dqs_io(void) +{ + uint32_t addr = sdr_get_addr(&sdr_scc_mgr->dqs_io_ena); + + writel(0, SOCFPGA_SDR_ADDRESS + addr); +} + +/* load up dq config settings */ +static void scc_mgr_load_dq(uint32_t dq_in_group) +{ + uint32_t addr = sdr_get_addr(&sdr_scc_mgr->dq_ena); + + writel(dq_in_group, SOCFPGA_SDR_ADDRESS + addr); +} + +/* load up dm config settings */ +static void scc_mgr_load_dm(uint32_t dm) +{ + uint32_t addr = sdr_get_addr(&sdr_scc_mgr->dm_ena); + + writel(dm, SOCFPGA_SDR_ADDRESS + addr); +} + +/* + * apply and load a particular input delay for the DQ pins in a group + * group_bgn is the index of the first dq pin (in the write group) + */ +static void scc_mgr_apply_group_dq_in_delay(uint32_t write_group, + uint32_t group_bgn, uint32_t delay) +{ + uint32_t i, p; + + for (i = 0, p = group_bgn; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++, p++) { + scc_mgr_set_dq_in_delay(write_group, p, delay); + scc_mgr_load_dq(p); + } +} + +/* apply and load a particular output delay for the DQ pins in a group */ +static void scc_mgr_apply_group_dq_out1_delay(uint32_t write_group, + uint32_t group_bgn, + uint32_t delay1) +{ + uint32_t i, p; + + for (i = 0, p = group_bgn; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++, p++) { + scc_mgr_set_dq_out1_delay(write_group, i, delay1); + scc_mgr_load_dq(i); + } +} + +/* apply and load a particular output delay for the DM pins in a group */ +static void scc_mgr_apply_group_dm_out1_delay(uint32_t write_group, + uint32_t delay1) +{ + uint32_t i; + + for (i = 0; i < RW_MGR_NUM_DM_PER_WRITE_GROUP; i++) { + scc_mgr_set_dm_out1_delay(write_group, i, delay1); + scc_mgr_load_dm(i); + } +} + + +/* apply and load delay on both DQS and OCT out1 */ +static void scc_mgr_apply_group_dqs_io_and_oct_out1(uint32_t write_group, + uint32_t delay) +{ + scc_mgr_set_dqs_out1_delay(write_group, delay); + scc_mgr_load_dqs_io(); + + scc_mgr_set_oct_out1_delay(write_group, delay); + scc_mgr_load_dqs_for_write_group(write_group); +} + +/* apply a delay to the entire output side: DQ, DM, DQS, OCT */ +static void scc_mgr_apply_group_all_out_delay_add(uint32_t write_group, + uint32_t group_bgn, + uint32_t delay) +{ + uint32_t i, p, new_delay; + + /* dq shift */ + for (i = 0, p = group_bgn; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++, p++) { + new_delay = READ_SCC_DQ_OUT2_DELAY; + new_delay += delay; + + if (new_delay > IO_IO_OUT2_DELAY_MAX) { + debug_cond(DLEVEL == 1, "%s:%d (%u, %u, %u) DQ[%u,%u]:\ + %u > %lu => %lu", __func__, __LINE__, + write_group, group_bgn, delay, i, p, new_delay, + (long unsigned int)IO_IO_OUT2_DELAY_MAX, + (long unsigned int)IO_IO_OUT2_DELAY_MAX); + new_delay = IO_IO_OUT2_DELAY_MAX; + } + + scc_mgr_load_dq(i); + } + + /* dm shift */ + for (i = 0; i < RW_MGR_NUM_DM_PER_WRITE_GROUP; i++) { + new_delay = READ_SCC_DM_IO_OUT2_DELAY; + new_delay += delay; + + if (new_delay > IO_IO_OUT2_DELAY_MAX) { + debug_cond(DLEVEL == 1, "%s:%d (%u, %u, %u) DM[%u]:\ + %u > %lu => %lu\n", __func__, __LINE__, + write_group, group_bgn, delay, i, new_delay, + (long unsigned int)IO_IO_OUT2_DELAY_MAX, + (long unsigned int)IO_IO_OUT2_DELAY_MAX); + new_delay = IO_IO_OUT2_DELAY_MAX; + } + + scc_mgr_load_dm(i); + } + + /* dqs shift */ + new_delay = READ_SCC_DQS_IO_OUT2_DELAY; + new_delay += delay; + + if (new_delay > IO_IO_OUT2_DELAY_MAX) { + debug_cond(DLEVEL == 1, "%s:%d (%u, %u, %u) DQS: %u > %d => %d;" + " adding %u to OUT1\n", __func__, __LINE__, + write_group, group_bgn, delay, new_delay, + IO_IO_OUT2_DELAY_MAX, IO_IO_OUT2_DELAY_MAX, + new_delay - IO_IO_OUT2_DELAY_MAX); + scc_mgr_set_dqs_out1_delay(write_group, new_delay - + IO_IO_OUT2_DELAY_MAX); + new_delay = IO_IO_OUT2_DELAY_MAX; + } + + scc_mgr_load_dqs_io(); + + /* oct shift */ + new_delay = READ_SCC_OCT_OUT2_DELAY; + new_delay += delay; + + if (new_delay > IO_IO_OUT2_DELAY_MAX) { + debug_cond(DLEVEL == 1, "%s:%d (%u, %u, %u) DQS: %u > %d => %d;" + " adding %u to OUT1\n", __func__, __LINE__, + write_group, group_bgn, delay, new_delay, + IO_IO_OUT2_DELAY_MAX, IO_IO_OUT2_DELAY_MAX, + new_delay - IO_IO_OUT2_DELAY_MAX); + scc_mgr_set_oct_out1_delay(write_group, new_delay - + IO_IO_OUT2_DELAY_MAX); + new_delay = IO_IO_OUT2_DELAY_MAX; + } + + scc_mgr_load_dqs_for_write_group(write_group); +} + +/* + * USER apply a delay to the entire output side (DQ, DM, DQS, OCT) + * and to all ranks + */ +static void scc_mgr_apply_group_all_out_delay_add_all_ranks( + uint32_t write_group, uint32_t group_bgn, uint32_t delay) +{ + uint32_t r; + uint32_t addr = sdr_get_addr(&sdr_scc_mgr->update); + + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; + r += NUM_RANKS_PER_SHADOW_REG) { + scc_mgr_apply_group_all_out_delay_add(write_group, + group_bgn, delay); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + } +} + +/* optimization used to recover some slots in ddr3 inst_rom */ +/* could be applied to other protocols if we wanted to */ +static void set_jump_as_return(void) +{ + uint32_t addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr0); + + /* + * to save space, we replace return with jump to special shared + * RETURN instruction so we set the counter to large value so that + * we always jump + */ + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add0); + writel(RW_MGR_RETURN, SOCFPGA_SDR_ADDRESS + addr); +} + +/* + * should always use constants as argument to ensure all computations are + * performed at compile time + */ +static void delay_for_n_mem_clocks(const uint32_t clocks) +{ + uint32_t afi_clocks; + uint8_t inner = 0; + uint8_t outer = 0; + uint16_t c_loop = 0; + uint32_t addr; + + debug("%s:%d: clocks=%u ... start\n", __func__, __LINE__, clocks); + + + afi_clocks = (clocks + AFI_RATE_RATIO-1) / AFI_RATE_RATIO; + /* scale (rounding up) to get afi clocks */ + + /* + * Note, we don't bother accounting for being off a little bit + * because of a few extra instructions in outer loops + * Note, the loops have a test at the end, and do the test before + * the decrement, and so always perform the loop + * 1 time more than the counter value + */ + if (afi_clocks == 0) { + ; + } else if (afi_clocks <= 0x100) { + inner = afi_clocks-1; + outer = 0; + c_loop = 0; + } else if (afi_clocks <= 0x10000) { + inner = 0xff; + outer = (afi_clocks-1) >> 8; + c_loop = 0; + } else { + inner = 0xff; + outer = 0xff; + c_loop = (afi_clocks-1) >> 16; + } + + /* + * rom instructions are structured as follows: + * + * IDLE_LOOP2: jnz cntr0, TARGET_A + * IDLE_LOOP1: jnz cntr1, TARGET_B + * return + * + * so, when doing nested loops, TARGET_A is set to IDLE_LOOP2, and + * TARGET_B is set to IDLE_LOOP2 as well + * + * if we have no outer loop, though, then we can use IDLE_LOOP1 only, + * and set TARGET_B to IDLE_LOOP1 and we skip IDLE_LOOP2 entirely + * + * a little confusing, but it helps save precious space in the inst_rom + * and sequencer rom and keeps the delays more accurate and reduces + * overhead + */ + if (afi_clocks <= 0x100) { + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr1); + writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(inner), SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add1); + writel(RW_MGR_IDLE_LOOP1, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_IDLE_LOOP1, SOCFPGA_SDR_ADDRESS + addr); + } else { + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr0); + writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(inner), SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr1); + writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(outer), SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add0); + writel(RW_MGR_IDLE_LOOP2, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add1); + writel(RW_MGR_IDLE_LOOP2, SOCFPGA_SDR_ADDRESS + addr); + + /* hack to get around compiler not being smart enough */ + if (afi_clocks <= 0x10000) { + /* only need to run once */ + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_IDLE_LOOP2, SOCFPGA_SDR_ADDRESS + addr); + } else { + do { + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_IDLE_LOOP2, SOCFPGA_SDR_ADDRESS + addr); + } while (c_loop-- != 0); + } + } + debug("%s:%d clocks=%u ... end\n", __func__, __LINE__, clocks); +} + +static void rw_mgr_mem_initialize(void) +{ + uint32_t r; + uint32_t addr; + + debug("%s:%d\n", __func__, __LINE__); + + /* The reset / cke part of initialization is broadcasted to all ranks */ + addr = sdr_get_addr((u32 *)RW_MGR_SET_CS_AND_ODT_MASK); + writel(RW_MGR_RANK_ALL, SOCFPGA_SDR_ADDRESS + addr); + + /* + * Here's how you load register for a loop + * Counters are located @ 0x800 + * Jump address are located @ 0xC00 + * For both, registers 0 to 3 are selected using bits 3 and 2, like + * in 0x800, 0x804, 0x808, 0x80C and 0xC00, 0xC04, 0xC08, 0xC0C + * I know this ain't pretty, but Avalon bus throws away the 2 least + * significant bits + */ + + /* start with memory RESET activated */ + + /* tINIT = 200us */ + + /* + * 200us @ 266MHz (3.75 ns) ~ 54000 clock cycles + * If a and b are the number of iteration in 2 nested loops + * it takes the following number of cycles to complete the operation: + * number_of_cycles = ((2 + n) * a + 2) * b + * where n is the number of instruction in the inner loop + * One possible solution is n = 0 , a = 256 , b = 106 => a = FF, + * b = 6A + */ + + /* Load counters */ + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr0); + writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TINIT_CNTR0_VAL), + SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr1); + writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TINIT_CNTR1_VAL), + SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr2); + writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TINIT_CNTR2_VAL), + SOCFPGA_SDR_ADDRESS + addr); + + /* Load jump address */ + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add0); + writel(RW_MGR_INIT_RESET_0_CKE_0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add1); + writel(RW_MGR_INIT_RESET_0_CKE_0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add2); + writel(RW_MGR_INIT_RESET_0_CKE_0, SOCFPGA_SDR_ADDRESS + addr); + + /* Execute count instruction */ + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_INIT_RESET_0_CKE_0, SOCFPGA_SDR_ADDRESS + addr); + + /* indicate that memory is stable */ + addr = sdr_get_addr(&phy_mgr_cfg->reset_mem_stbl); + writel(1, SOCFPGA_SDR_ADDRESS + addr); + + /* + * transition the RESET to high + * Wait for 500us + */ + + /* + * 500us @ 266MHz (3.75 ns) ~ 134000 clock cycles + * If a and b are the number of iteration in 2 nested loops + * it takes the following number of cycles to complete the operation + * number_of_cycles = ((2 + n) * a + 2) * b + * where n is the number of instruction in the inner loop + * One possible solution is n = 2 , a = 131 , b = 256 => a = 83, + * b = FF + */ + + /* Load counters */ + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr0); + writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TRESET_CNTR0_VAL), + SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr1); + writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TRESET_CNTR1_VAL), + SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr2); + writel(SKIP_DELAY_LOOP_VALUE_OR_ZERO(SEQ_TRESET_CNTR2_VAL), + SOCFPGA_SDR_ADDRESS + addr); + + /* Load jump address */ + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add0); + writel(RW_MGR_INIT_RESET_1_CKE_0, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add1); + writel(RW_MGR_INIT_RESET_1_CKE_0, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add2); + writel(RW_MGR_INIT_RESET_1_CKE_0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_INIT_RESET_1_CKE_0, SOCFPGA_SDR_ADDRESS + addr); + + /* bring up clock enable */ + + /* tXRP < 250 ck cycles */ + delay_for_n_mem_clocks(250); + + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; r++) { + if (param->skip_ranks[r]) { + /* request to skip the rank */ + continue; + } + + /* set rank */ + set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_OFF); + + /* + * USER Use Mirror-ed commands for odd ranks if address + * mirrorring is on + */ + if ((RW_MGR_MEM_ADDRESS_MIRRORING >> r) & 0x1) { + set_jump_as_return(); + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_MRS2_MIRR, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS3_MIRR, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS1_MIRR, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS0_DLL_RESET_MIRR, SOCFPGA_SDR_ADDRESS + addr); + } else { + set_jump_as_return(); + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_MRS2, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS3, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS1, SOCFPGA_SDR_ADDRESS + addr); + set_jump_as_return(); + writel(RW_MGR_MRS0_DLL_RESET, SOCFPGA_SDR_ADDRESS + addr); + } + set_jump_as_return(); + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_ZQCL, SOCFPGA_SDR_ADDRESS + addr); + + /* tZQinit = tDLLK = 512 ck cycles */ + delay_for_n_mem_clocks(512); + } +} + +/* + * At the end of calibration we have to program the user settings in, and + * USER hand off the memory to the user. + */ +static void rw_mgr_mem_handoff(void) +{ + uint32_t r; + uint32_t addr; + + debug("%s:%d\n", __func__, __LINE__); + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; r++) { + if (param->skip_ranks[r]) + /* request to skip the rank */ + continue; + /* set rank */ + set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_OFF); + + /* precharge all banks ... */ + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_PRECHARGE_ALL, SOCFPGA_SDR_ADDRESS + addr); + + /* load up MR settings specified by user */ + + /* + * Use Mirror-ed commands for odd ranks if address + * mirrorring is on + */ + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + if ((RW_MGR_MEM_ADDRESS_MIRRORING >> r) & 0x1) { + set_jump_as_return(); + writel(RW_MGR_MRS2_MIRR, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS3_MIRR, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS1_MIRR, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS0_USER_MIRR, SOCFPGA_SDR_ADDRESS + addr); + } else { + set_jump_as_return(); + writel(RW_MGR_MRS2, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS3, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS1, SOCFPGA_SDR_ADDRESS + addr); + delay_for_n_mem_clocks(4); + set_jump_as_return(); + writel(RW_MGR_MRS0_USER, SOCFPGA_SDR_ADDRESS + addr); + } + /* + * USER need to wait tMOD (12CK or 15ns) time before issuing + * other commands, but we will have plenty of NIOS cycles before + * actual handoff so its okay. + */ + } +} + +/* + * performs a guaranteed read on the patterns we are going to use during a + * read test to ensure memory works + */ +static uint32_t rw_mgr_mem_calibrate_read_test_patterns(uint32_t rank_bgn, + uint32_t group, uint32_t num_tries, uint32_t *bit_chk, + uint32_t all_ranks) +{ + uint32_t r, vg; + uint32_t correct_mask_vg; + uint32_t tmp_bit_chk; + uint32_t rank_end = all_ranks ? RW_MGR_MEM_NUMBER_OF_RANKS : + (rank_bgn + NUM_RANKS_PER_SHADOW_REG); + uint32_t addr; + uint32_t base_rw_mgr; + + *bit_chk = param->read_correct_mask; + correct_mask_vg = param->read_correct_mask_vg; + + for (r = rank_bgn; r < rank_end; r++) { + if (param->skip_ranks[r]) + /* request to skip the rank */ + continue; + + /* set rank */ + set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_READ_WRITE); + + /* Load up a constant bursts of read commands */ + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr0); + writel(0x20, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add0); + writel(RW_MGR_GUARANTEED_READ, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr1); + writel(0x20, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add1); + writel(RW_MGR_GUARANTEED_READ_CONT, SOCFPGA_SDR_ADDRESS + addr); + + tmp_bit_chk = 0; + for (vg = RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS-1; ; vg--) { + /* reset the fifos to get pointers to known state */ + + addr = sdr_get_addr(&phy_mgr_cmd->fifo_reset); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr((u32 *)RW_MGR_RESET_READ_DATAPATH); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + tmp_bit_chk = tmp_bit_chk << (RW_MGR_MEM_DQ_PER_READ_DQS + / RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS); + + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_GUARANTEED_READ, SOCFPGA_SDR_ADDRESS + addr + + ((group * RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS + + vg) << 2)); + + addr = sdr_get_addr((u32 *)BASE_RW_MGR); + base_rw_mgr = readl(SOCFPGA_SDR_ADDRESS + addr); + tmp_bit_chk = tmp_bit_chk | (correct_mask_vg & (~base_rw_mgr)); + + if (vg == 0) + break; + } + *bit_chk &= tmp_bit_chk; + } + + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_CLEAR_DQS_ENABLE, SOCFPGA_SDR_ADDRESS + addr + (group << 2)); + + set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF); + debug_cond(DLEVEL == 1, "%s:%d test_load_patterns(%u,ALL) => (%u == %u) =>\ + %lu\n", __func__, __LINE__, group, *bit_chk, param->read_correct_mask, + (long unsigned int)(*bit_chk == param->read_correct_mask)); + return *bit_chk == param->read_correct_mask; +} + +static uint32_t rw_mgr_mem_calibrate_read_test_patterns_all_ranks + (uint32_t group, uint32_t num_tries, uint32_t *bit_chk) +{ + return rw_mgr_mem_calibrate_read_test_patterns(0, group, + num_tries, bit_chk, 1); +} + +/* load up the patterns we are going to use during a read test */ +static void rw_mgr_mem_calibrate_read_load_patterns(uint32_t rank_bgn, + uint32_t all_ranks) +{ + uint32_t r; + uint32_t addr; + uint32_t rank_end = all_ranks ? RW_MGR_MEM_NUMBER_OF_RANKS : + (rank_bgn + NUM_RANKS_PER_SHADOW_REG); + + debug("%s:%d\n", __func__, __LINE__); + for (r = rank_bgn; r < rank_end; r++) { + if (param->skip_ranks[r]) + /* request to skip the rank */ + continue; + + /* set rank */ + set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_READ_WRITE); + + /* Load up a constant bursts */ + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr0); + writel(0x20, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add0); + writel(RW_MGR_GUARANTEED_WRITE_WAIT0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr1); + writel(0x20, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add1); + writel(RW_MGR_GUARANTEED_WRITE_WAIT1, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr2); + writel(0x04, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add2); + writel(RW_MGR_GUARANTEED_WRITE_WAIT2, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr3); + writel(0x04, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add3); + writel(RW_MGR_GUARANTEED_WRITE_WAIT3, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_GUARANTEED_WRITE, SOCFPGA_SDR_ADDRESS + addr); + } + + set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF); +} + +/* + * try a read and see if it returns correct data back. has dummy reads + * inserted into the mix used to align dqs enable. has more thorough checks + * than the regular read test. + */ +static uint32_t rw_mgr_mem_calibrate_read_test(uint32_t rank_bgn, uint32_t group, + uint32_t num_tries, uint32_t all_correct, uint32_t *bit_chk, + uint32_t all_groups, uint32_t all_ranks) +{ + uint32_t r, vg; + uint32_t correct_mask_vg; + uint32_t tmp_bit_chk; + uint32_t rank_end = all_ranks ? RW_MGR_MEM_NUMBER_OF_RANKS : + (rank_bgn + NUM_RANKS_PER_SHADOW_REG); + uint32_t addr; + uint32_t base_rw_mgr; + + *bit_chk = param->read_correct_mask; + correct_mask_vg = param->read_correct_mask_vg; + + uint32_t quick_read_mode = (((STATIC_CALIB_STEPS) & + CALIB_SKIP_DELAY_SWEEPS) && ENABLE_SUPER_QUICK_CALIBRATION); + + for (r = rank_bgn; r < rank_end; r++) { + if (param->skip_ranks[r]) + /* request to skip the rank */ + continue; + + /* set rank */ + set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_READ_WRITE); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr1); + writel(0x10, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add1); + writel(RW_MGR_READ_B2B_WAIT1, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr2); + writel(0x10, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add2); + writel(RW_MGR_READ_B2B_WAIT2, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr0); + if (quick_read_mode) + writel(0x1, SOCFPGA_SDR_ADDRESS + addr); + /* need at least two (1+1) reads to capture failures */ + else if (all_groups) + writel(0x06, SOCFPGA_SDR_ADDRESS + addr); + else + writel(0x32, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add0); + writel(RW_MGR_READ_B2B, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr3); + if (all_groups) + writel(RW_MGR_MEM_IF_READ_DQS_WIDTH * + RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS - 1, + SOCFPGA_SDR_ADDRESS + addr); + else + writel(0x0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add3); + writel(RW_MGR_READ_B2B, SOCFPGA_SDR_ADDRESS + addr); + + tmp_bit_chk = 0; + for (vg = RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS-1; ; vg--) { + /* reset the fifos to get pointers to known state */ + addr = sdr_get_addr(&phy_mgr_cmd->fifo_reset); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr((u32 *)RW_MGR_RESET_READ_DATAPATH); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + tmp_bit_chk = tmp_bit_chk << (RW_MGR_MEM_DQ_PER_READ_DQS + / RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS); + + addr = sdr_get_addr((u32 *)(all_groups ? RW_MGR_RUN_ALL_GROUPS : + RW_MGR_RUN_SINGLE_GROUP)); + writel(RW_MGR_READ_B2B, SOCFPGA_SDR_ADDRESS + addr + + ((group * RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS + + vg) << 2)); + + addr = sdr_get_addr((u32 *)BASE_RW_MGR); + base_rw_mgr = readl(SOCFPGA_SDR_ADDRESS + addr); + tmp_bit_chk = tmp_bit_chk | (correct_mask_vg & ~(base_rw_mgr)); + + if (vg == 0) + break; + } + *bit_chk &= tmp_bit_chk; + } + + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_CLEAR_DQS_ENABLE, SOCFPGA_SDR_ADDRESS + addr + (group << 2)); + + if (all_correct) { + set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF); + debug_cond(DLEVEL == 2, "%s:%d read_test(%u,ALL,%u) =>\ + (%u == %u) => %lu", __func__, __LINE__, group, + all_groups, *bit_chk, param->read_correct_mask, + (long unsigned int)(*bit_chk == + param->read_correct_mask)); + return *bit_chk == param->read_correct_mask; + } else { + set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF); + debug_cond(DLEVEL == 2, "%s:%d read_test(%u,ONE,%u) =>\ + (%u != %lu) => %lu\n", __func__, __LINE__, + group, all_groups, *bit_chk, (long unsigned int)0, + (long unsigned int)(*bit_chk != 0x00)); + return *bit_chk != 0x00; + } +} + +static uint32_t rw_mgr_mem_calibrate_read_test_all_ranks(uint32_t group, + uint32_t num_tries, uint32_t all_correct, uint32_t *bit_chk, + uint32_t all_groups) +{ + return rw_mgr_mem_calibrate_read_test(0, group, num_tries, all_correct, + bit_chk, all_groups, 1); +} + +static void rw_mgr_incr_vfifo(uint32_t grp, uint32_t *v) +{ + uint32_t addr = sdr_get_addr(&phy_mgr_cmd->inc_vfifo_hard_phy); + + writel(grp, SOCFPGA_SDR_ADDRESS + addr); + (*v)++; +} + +static void rw_mgr_decr_vfifo(uint32_t grp, uint32_t *v) +{ + uint32_t i; + + for (i = 0; i < VFIFO_SIZE-1; i++) + rw_mgr_incr_vfifo(grp, v); +} + +static int find_vfifo_read(uint32_t grp, uint32_t *bit_chk) +{ + uint32_t v; + uint32_t fail_cnt = 0; + uint32_t test_status; + + for (v = 0; v < VFIFO_SIZE; ) { + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: vfifo %u\n", + __func__, __LINE__, v); + test_status = rw_mgr_mem_calibrate_read_test_all_ranks + (grp, 1, PASS_ONE_BIT, bit_chk, 0); + if (!test_status) { + fail_cnt++; + + if (fail_cnt == 2) + break; + } + + /* fiddle with FIFO */ + rw_mgr_incr_vfifo(grp, &v); + } + + if (v >= VFIFO_SIZE) { + /* no failing read found!! Something must have gone wrong */ + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: vfifo failed\n", + __func__, __LINE__); + return 0; + } else { + return v; + } +} + +static int find_working_phase(uint32_t *grp, uint32_t *bit_chk, + uint32_t dtaps_per_ptap, uint32_t *work_bgn, + uint32_t *v, uint32_t *d, uint32_t *p, + uint32_t *i, uint32_t *max_working_cnt) +{ + uint32_t found_begin = 0; + uint32_t tmp_delay = 0; + uint32_t test_status; + + for (*d = 0; *d <= dtaps_per_ptap; (*d)++, tmp_delay += + IO_DELAY_PER_DQS_EN_DCHAIN_TAP) { + *work_bgn = tmp_delay; + scc_mgr_set_dqs_en_delay_all_ranks(*grp, *d); + + for (*i = 0; *i < VFIFO_SIZE; (*i)++) { + for (*p = 0; *p <= IO_DQS_EN_PHASE_MAX; (*p)++, *work_bgn += + IO_DELAY_PER_OPA_TAP) { + scc_mgr_set_dqs_en_phase_all_ranks(*grp, *p); + + test_status = + rw_mgr_mem_calibrate_read_test_all_ranks + (*grp, 1, PASS_ONE_BIT, bit_chk, 0); + + if (test_status) { + *max_working_cnt = 1; + found_begin = 1; + break; + } + } + + if (found_begin) + break; + + if (*p > IO_DQS_EN_PHASE_MAX) + /* fiddle with FIFO */ + rw_mgr_incr_vfifo(*grp, v); + } + + if (found_begin) + break; + } + + if (*i >= VFIFO_SIZE) { + /* cannot find working solution */ + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: no vfifo/\ + ptap/dtap\n", __func__, __LINE__); + return 0; + } else { + return 1; + } +} + +static void sdr_backup_phase(uint32_t *grp, uint32_t *bit_chk, + uint32_t *work_bgn, uint32_t *v, uint32_t *d, + uint32_t *p, uint32_t *max_working_cnt) +{ + uint32_t found_begin = 0; + uint32_t tmp_delay; + + /* Special case code for backing up a phase */ + if (*p == 0) { + *p = IO_DQS_EN_PHASE_MAX; + rw_mgr_decr_vfifo(*grp, v); + } else { + (*p)--; + } + tmp_delay = *work_bgn - IO_DELAY_PER_OPA_TAP; + scc_mgr_set_dqs_en_phase_all_ranks(*grp, *p); + + for (*d = 0; *d <= IO_DQS_EN_DELAY_MAX && tmp_delay < *work_bgn; + (*d)++, tmp_delay += IO_DELAY_PER_DQS_EN_DCHAIN_TAP) { + scc_mgr_set_dqs_en_delay_all_ranks(*grp, *d); + + if (rw_mgr_mem_calibrate_read_test_all_ranks(*grp, 1, + PASS_ONE_BIT, + bit_chk, 0)) { + found_begin = 1; + *work_bgn = tmp_delay; + break; + } + } + + /* We have found a working dtap before the ptap found above */ + if (found_begin == 1) + (*max_working_cnt)++; + + /* + * Restore VFIFO to old state before we decremented it + * (if needed). + */ + (*p)++; + if (*p > IO_DQS_EN_PHASE_MAX) { + *p = 0; + rw_mgr_incr_vfifo(*grp, v); + } + + scc_mgr_set_dqs_en_delay_all_ranks(*grp, 0); +} + +static int sdr_nonworking_phase(uint32_t *grp, uint32_t *bit_chk, + uint32_t *work_bgn, uint32_t *v, uint32_t *d, + uint32_t *p, uint32_t *i, uint32_t *max_working_cnt, + uint32_t *work_end) +{ + uint32_t found_end = 0; + + (*p)++; + *work_end += IO_DELAY_PER_OPA_TAP; + if (*p > IO_DQS_EN_PHASE_MAX) { + /* fiddle with FIFO */ + *p = 0; + rw_mgr_incr_vfifo(*grp, v); + } + + for (; *i < VFIFO_SIZE + 1; (*i)++) { + for (; *p <= IO_DQS_EN_PHASE_MAX; (*p)++, *work_end + += IO_DELAY_PER_OPA_TAP) { + scc_mgr_set_dqs_en_phase_all_ranks(*grp, *p); + + if (!rw_mgr_mem_calibrate_read_test_all_ranks + (*grp, 1, PASS_ONE_BIT, bit_chk, 0)) { + found_end = 1; + break; + } else { + (*max_working_cnt)++; + } + } + + if (found_end) + break; + + if (*p > IO_DQS_EN_PHASE_MAX) { + /* fiddle with FIFO */ + rw_mgr_incr_vfifo(*grp, v); + *p = 0; + } + } + + if (*i >= VFIFO_SIZE + 1) { + /* cannot see edge of failing read */ + debug_cond(DLEVEL == 2, "%s:%d sdr_nonworking_phase: end:\ + failed\n", __func__, __LINE__); + return 0; + } else { + return 1; + } +} + +static int sdr_find_window_centre(uint32_t *grp, uint32_t *bit_chk, + uint32_t *work_bgn, uint32_t *v, uint32_t *d, + uint32_t *p, uint32_t *work_mid, + uint32_t *work_end) +{ + int i; + int tmp_delay = 0; + + *work_mid = (*work_bgn + *work_end) / 2; + + debug_cond(DLEVEL == 2, "work_bgn=%d work_end=%d work_mid=%d\n", + *work_bgn, *work_end, *work_mid); + /* Get the middle delay to be less than a VFIFO delay */ + for (*p = 0; *p <= IO_DQS_EN_PHASE_MAX; + (*p)++, tmp_delay += IO_DELAY_PER_OPA_TAP) + ; + debug_cond(DLEVEL == 2, "vfifo ptap delay %d\n", tmp_delay); + while (*work_mid > tmp_delay) + *work_mid -= tmp_delay; + debug_cond(DLEVEL == 2, "new work_mid %d\n", *work_mid); + + tmp_delay = 0; + for (*p = 0; *p <= IO_DQS_EN_PHASE_MAX && tmp_delay < *work_mid; + (*p)++, tmp_delay += IO_DELAY_PER_OPA_TAP) + ; + tmp_delay -= IO_DELAY_PER_OPA_TAP; + debug_cond(DLEVEL == 2, "new p %d, tmp_delay=%d\n", (*p) - 1, tmp_delay); + for (*d = 0; *d <= IO_DQS_EN_DELAY_MAX && tmp_delay < *work_mid; (*d)++, + tmp_delay += IO_DELAY_PER_DQS_EN_DCHAIN_TAP) + ; + debug_cond(DLEVEL == 2, "new d %d, tmp_delay=%d\n", *d, tmp_delay); + + scc_mgr_set_dqs_en_phase_all_ranks(*grp, (*p) - 1); + scc_mgr_set_dqs_en_delay_all_ranks(*grp, *d); + + /* + * push vfifo until we can successfully calibrate. We can do this + * because the largest possible margin in 1 VFIFO cycle. + */ + for (i = 0; i < VFIFO_SIZE; i++) { + debug_cond(DLEVEL == 2, "find_dqs_en_phase: center: vfifo=%u\n", + *v); + if (rw_mgr_mem_calibrate_read_test_all_ranks(*grp, 1, + PASS_ONE_BIT, + bit_chk, 0)) { + break; + } + + /* fiddle with FIFO */ + rw_mgr_incr_vfifo(*grp, v); + } + + if (i >= VFIFO_SIZE) { + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: center: \ + failed\n", __func__, __LINE__); + return 0; + } else { + return 1; + } +} + +/* find a good dqs enable to use */ +static uint32_t rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase(uint32_t grp) +{ + uint32_t v, d, p, i; + uint32_t max_working_cnt; + uint32_t bit_chk; + uint32_t dtaps_per_ptap; + uint32_t work_bgn, work_mid, work_end; + uint32_t found_passing_read, found_failing_read, initial_failing_dtap; + uint32_t addr; + + debug("%s:%d %u\n", __func__, __LINE__, grp); + + reg_file_set_sub_stage(CAL_SUBSTAGE_VFIFO_CENTER); + + scc_mgr_set_dqs_en_delay_all_ranks(grp, 0); + scc_mgr_set_dqs_en_phase_all_ranks(grp, 0); + + /* ************************************************************** */ + /* * Step 0 : Determine number of delay taps for each phase tap * */ + dtaps_per_ptap = IO_DELAY_PER_OPA_TAP/IO_DELAY_PER_DQS_EN_DCHAIN_TAP; + + /* ********************************************************* */ + /* * Step 1 : First push vfifo until we get a failing read * */ + v = find_vfifo_read(grp, &bit_chk); + + max_working_cnt = 0; + + /* ******************************************************** */ + /* * step 2: find first working phase, increment in ptaps * */ + work_bgn = 0; + if (find_working_phase(&grp, &bit_chk, dtaps_per_ptap, &work_bgn, &v, &d, + &p, &i, &max_working_cnt) == 0) + return 0; + + work_end = work_bgn; + + /* + * If d is 0 then the working window covers a phase tap and + * we can follow the old procedure otherwise, we've found the beginning, + * and we need to increment the dtaps until we find the end. + */ + if (d == 0) { + /* ********************************************************* */ + /* * step 3a: if we have room, back off by one and + increment in dtaps * */ + + sdr_backup_phase(&grp, &bit_chk, &work_bgn, &v, &d, &p, + &max_working_cnt); + + /* ********************************************************* */ + /* * step 4a: go forward from working phase to non working + phase, increment in ptaps * */ + if (sdr_nonworking_phase(&grp, &bit_chk, &work_bgn, &v, &d, &p, + &i, &max_working_cnt, &work_end) == 0) + return 0; + + /* ********************************************************* */ + /* * step 5a: back off one from last, increment in dtaps * */ + + /* Special case code for backing up a phase */ + if (p == 0) { + p = IO_DQS_EN_PHASE_MAX; + rw_mgr_decr_vfifo(grp, &v); + } else { + p = p - 1; + } + + work_end -= IO_DELAY_PER_OPA_TAP; + scc_mgr_set_dqs_en_phase_all_ranks(grp, p); + + /* * The actual increment of dtaps is done outside of + the if/else loop to share code */ + d = 0; + + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: v/p: \ + vfifo=%u ptap=%u\n", __func__, __LINE__, + v, p); + } else { + /* ******************************************************* */ + /* * step 3-5b: Find the right edge of the window using + delay taps * */ + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase:vfifo=%u \ + ptap=%u dtap=%u bgn=%u\n", __func__, __LINE__, + v, p, d, work_bgn); + + work_end = work_bgn; + + /* * The actual increment of dtaps is done outside of the + if/else loop to share code */ + + /* Only here to counterbalance a subtract later on which is + not needed if this branch of the algorithm is taken */ + max_working_cnt++; + } + + /* The dtap increment to find the failing edge is done here */ + for (; d <= IO_DQS_EN_DELAY_MAX; d++, work_end += + IO_DELAY_PER_DQS_EN_DCHAIN_TAP) { + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: \ + end-2: dtap=%u\n", __func__, __LINE__, d); + scc_mgr_set_dqs_en_delay_all_ranks(grp, d); + + if (!rw_mgr_mem_calibrate_read_test_all_ranks(grp, 1, + PASS_ONE_BIT, + &bit_chk, 0)) { + break; + } + } + + /* Go back to working dtap */ + if (d != 0) + work_end -= IO_DELAY_PER_DQS_EN_DCHAIN_TAP; + + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: v/p/d: vfifo=%u \ + ptap=%u dtap=%u end=%u\n", __func__, __LINE__, + v, p, d-1, work_end); + + if (work_end < work_bgn) { + /* nil range */ + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: end-2: \ + failed\n", __func__, __LINE__); + return 0; + } + + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: found range [%u,%u]\n", + __func__, __LINE__, work_bgn, work_end); + + /* *************************************************************** */ + /* + * * We need to calculate the number of dtaps that equal a ptap + * * To do that we'll back up a ptap and re-find the edge of the + * * window using dtaps + */ + + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: calculate dtaps_per_ptap \ + for tracking\n", __func__, __LINE__); + + /* Special case code for backing up a phase */ + if (p == 0) { + p = IO_DQS_EN_PHASE_MAX; + rw_mgr_decr_vfifo(grp, &v); + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: backedup \ + cycle/phase: v=%u p=%u\n", __func__, __LINE__, + v, p); + } else { + p = p - 1; + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: backedup \ + phase only: v=%u p=%u", __func__, __LINE__, + v, p); + } + + scc_mgr_set_dqs_en_phase_all_ranks(grp, p); + + /* + * Increase dtap until we first see a passing read (in case the + * window is smaller than a ptap), + * and then a failing read to mark the edge of the window again + */ + + /* Find a passing read */ + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: find passing read\n", + __func__, __LINE__); + found_passing_read = 0; + found_failing_read = 0; + initial_failing_dtap = d; + for (; d <= IO_DQS_EN_DELAY_MAX; d++) { + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: testing \ + read d=%u\n", __func__, __LINE__, d); + scc_mgr_set_dqs_en_delay_all_ranks(grp, d); + + if (rw_mgr_mem_calibrate_read_test_all_ranks(grp, 1, + PASS_ONE_BIT, + &bit_chk, 0)) { + found_passing_read = 1; + break; + } + } + + if (found_passing_read) { + /* Find a failing read */ + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: find failing \ + read\n", __func__, __LINE__); + for (d = d + 1; d <= IO_DQS_EN_DELAY_MAX; d++) { + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: \ + testing read d=%u\n", __func__, __LINE__, d); + scc_mgr_set_dqs_en_delay_all_ranks(grp, d); + + if (!rw_mgr_mem_calibrate_read_test_all_ranks + (grp, 1, PASS_ONE_BIT, &bit_chk, 0)) { + found_failing_read = 1; + break; + } + } + } else { + debug_cond(DLEVEL == 1, "%s:%d find_dqs_en_phase: failed to \ + calculate dtaps", __func__, __LINE__); + debug_cond(DLEVEL == 1, "per ptap. Fall back on static value\n"); + } + + /* + * The dynamically calculated dtaps_per_ptap is only valid if we + * found a passing/failing read. If we didn't, it means d hit the max + * (IO_DQS_EN_DELAY_MAX). Otherwise, dtaps_per_ptap retains its + * statically calculated value. + */ + if (found_passing_read && found_failing_read) + dtaps_per_ptap = d - initial_failing_dtap; + + addr = sdr_get_addr(&sdr_reg_file->dtaps_per_ptap); + writel(dtaps_per_ptap, SOCFPGA_SDR_ADDRESS + addr); + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: dtaps_per_ptap=%u \ + - %u = %u", __func__, __LINE__, d, + initial_failing_dtap, dtaps_per_ptap); + + /* ******************************************** */ + /* * step 6: Find the centre of the window * */ + if (sdr_find_window_centre(&grp, &bit_chk, &work_bgn, &v, &d, &p, + &work_mid, &work_end) == 0) + return 0; + + debug_cond(DLEVEL == 2, "%s:%d find_dqs_en_phase: center found: \ + vfifo=%u ptap=%u dtap=%u\n", __func__, __LINE__, + v, p-1, d); + return 1; +} + +/* + * Try rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase across different + * dq_in_delay values + */ +static uint32_t +rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase_sweep_dq_in_delay +(uint32_t write_group, uint32_t read_group, uint32_t test_bgn) +{ + uint32_t found; + uint32_t i; + uint32_t p; + uint32_t d; + uint32_t r; + uint32_t addr; + + const uint32_t delay_step = IO_IO_IN_DELAY_MAX / + (RW_MGR_MEM_DQ_PER_READ_DQS-1); + /* we start at zero, so have one less dq to devide among */ + + debug("%s:%d (%u,%u,%u)", __func__, __LINE__, write_group, read_group, + test_bgn); + + /* try different dq_in_delays since the dq path is shorter than dqs */ + + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; + r += NUM_RANKS_PER_SHADOW_REG) { + for (i = 0, p = test_bgn, d = 0; i < RW_MGR_MEM_DQ_PER_READ_DQS; + i++, p++, d += delay_step) { + debug_cond(DLEVEL == 1, "%s:%d rw_mgr_mem_calibrate_\ + vfifo_find_dqs_", __func__, __LINE__); + debug_cond(DLEVEL == 1, "en_phase_sweep_dq_in_delay: g=%u/%u ", + write_group, read_group); + debug_cond(DLEVEL == 1, "r=%u, i=%u p=%u d=%u\n", r, i , p, d); + scc_mgr_set_dq_in_delay(write_group, p, d); + scc_mgr_load_dq(p); + } + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + } + + found = rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase(read_group); + + debug_cond(DLEVEL == 1, "%s:%d rw_mgr_mem_calibrate_vfifo_find_dqs_\ + en_phase_sweep_dq", __func__, __LINE__); + debug_cond(DLEVEL == 1, "_in_delay: g=%u/%u found=%u; Reseting delay \ + chain to zero\n", write_group, read_group, found); + + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; + r += NUM_RANKS_PER_SHADOW_REG) { + for (i = 0, p = test_bgn; i < RW_MGR_MEM_DQ_PER_READ_DQS; + i++, p++) { + scc_mgr_set_dq_in_delay(write_group, p, 0); + scc_mgr_load_dq(p); + } + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + } + + return found; +} + +/* per-bit deskew DQ and center */ +static uint32_t rw_mgr_mem_calibrate_vfifo_center(uint32_t rank_bgn, + uint32_t write_group, uint32_t read_group, uint32_t test_bgn, + uint32_t use_read_test, uint32_t update_fom) +{ + uint32_t i, p, d, min_index; + /* + * Store these as signed since there are comparisons with + * signed numbers. + */ + uint32_t bit_chk; + uint32_t sticky_bit_chk; + int32_t left_edge[RW_MGR_MEM_DQ_PER_READ_DQS]; + int32_t right_edge[RW_MGR_MEM_DQ_PER_READ_DQS]; + int32_t final_dq[RW_MGR_MEM_DQ_PER_READ_DQS]; + int32_t mid; + int32_t orig_mid_min, mid_min; + int32_t new_dqs, start_dqs, start_dqs_en, shift_dq, final_dqs, + final_dqs_en; + int32_t dq_margin, dqs_margin; + uint32_t stop; + uint32_t temp_dq_in_delay1, temp_dq_in_delay2; + uint32_t addr; + + debug("%s:%d: %u %u", __func__, __LINE__, read_group, test_bgn); + + addr = sdr_get_addr((u32 *)SCC_MGR_DQS_IN_DELAY); + start_dqs = readl(SOCFPGA_SDR_ADDRESS + addr + (read_group << 2)); + if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS) + start_dqs_en = readl(SOCFPGA_SDR_ADDRESS + addr + ((read_group << 2) + - IO_DQS_EN_DELAY_OFFSET)); + + /* set the left and right edge of each bit to an illegal value */ + /* use (IO_IO_IN_DELAY_MAX + 1) as an illegal value */ + sticky_bit_chk = 0; + for (i = 0; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) { + left_edge[i] = IO_IO_IN_DELAY_MAX + 1; + right_edge[i] = IO_IO_IN_DELAY_MAX + 1; + } + + addr = sdr_get_addr(&sdr_scc_mgr->update); + /* Search for the left edge of the window for each bit */ + for (d = 0; d <= IO_IO_IN_DELAY_MAX; d++) { + scc_mgr_apply_group_dq_in_delay(write_group, test_bgn, d); + + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* + * Stop searching when the read test doesn't pass AND when + * we've seen a passing read on every bit. + */ + if (use_read_test) { + stop = !rw_mgr_mem_calibrate_read_test(rank_bgn, + read_group, NUM_READ_PB_TESTS, PASS_ONE_BIT, + &bit_chk, 0, 0); + } else { + rw_mgr_mem_calibrate_write_test(rank_bgn, write_group, + 0, PASS_ONE_BIT, + &bit_chk, 0); + bit_chk = bit_chk >> (RW_MGR_MEM_DQ_PER_READ_DQS * + (read_group - (write_group * + RW_MGR_MEM_IF_READ_DQS_WIDTH / + RW_MGR_MEM_IF_WRITE_DQS_WIDTH))); + stop = (bit_chk == 0); + } + sticky_bit_chk = sticky_bit_chk | bit_chk; + stop = stop && (sticky_bit_chk == param->read_correct_mask); + debug_cond(DLEVEL == 2, "%s:%d vfifo_center(left): dtap=%u => %u == %u \ + && %u", __func__, __LINE__, d, + sticky_bit_chk, + param->read_correct_mask, stop); + + if (stop == 1) { + break; + } else { + for (i = 0; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) { + if (bit_chk & 1) { + /* Remember a passing test as the + left_edge */ + left_edge[i] = d; + } else { + /* If a left edge has not been seen yet, + then a future passing test will mark + this edge as the right edge */ + if (left_edge[i] == + IO_IO_IN_DELAY_MAX + 1) { + right_edge[i] = -(d + 1); + } + } + bit_chk = bit_chk >> 1; + } + } + } + + /* Reset DQ delay chains to 0 */ + scc_mgr_apply_group_dq_in_delay(write_group, test_bgn, 0); + sticky_bit_chk = 0; + for (i = RW_MGR_MEM_DQ_PER_READ_DQS - 1;; i--) { + debug_cond(DLEVEL == 2, "%s:%d vfifo_center: left_edge[%u]: \ + %d right_edge[%u]: %d\n", __func__, __LINE__, + i, left_edge[i], i, right_edge[i]); + + /* + * Check for cases where we haven't found the left edge, + * which makes our assignment of the the right edge invalid. + * Reset it to the illegal value. + */ + if ((left_edge[i] == IO_IO_IN_DELAY_MAX + 1) && ( + right_edge[i] != IO_IO_IN_DELAY_MAX + 1)) { + right_edge[i] = IO_IO_IN_DELAY_MAX + 1; + debug_cond(DLEVEL == 2, "%s:%d vfifo_center: reset \ + right_edge[%u]: %d\n", __func__, __LINE__, + i, right_edge[i]); + } + + /* + * Reset sticky bit (except for bits where we have seen + * both the left and right edge). + */ + sticky_bit_chk = sticky_bit_chk << 1; + if ((left_edge[i] != IO_IO_IN_DELAY_MAX + 1) && + (right_edge[i] != IO_IO_IN_DELAY_MAX + 1)) { + sticky_bit_chk = sticky_bit_chk | 1; + } + + if (i == 0) + break; + } + + addr = sdr_get_addr(&sdr_scc_mgr->update); + /* Search for the right edge of the window for each bit */ + for (d = 0; d <= IO_DQS_IN_DELAY_MAX - start_dqs; d++) { + scc_mgr_set_dqs_bus_in_delay(read_group, d + start_dqs); + if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS) { + uint32_t delay = d + start_dqs_en; + if (delay > IO_DQS_EN_DELAY_MAX) + delay = IO_DQS_EN_DELAY_MAX; + scc_mgr_set_dqs_en_delay(read_group, delay); + } + scc_mgr_load_dqs(read_group); + + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* + * Stop searching when the read test doesn't pass AND when + * we've seen a passing read on every bit. + */ + if (use_read_test) { + stop = !rw_mgr_mem_calibrate_read_test(rank_bgn, + read_group, NUM_READ_PB_TESTS, PASS_ONE_BIT, + &bit_chk, 0, 0); + } else { + rw_mgr_mem_calibrate_write_test(rank_bgn, write_group, + 0, PASS_ONE_BIT, + &bit_chk, 0); + bit_chk = bit_chk >> (RW_MGR_MEM_DQ_PER_READ_DQS * + (read_group - (write_group * + RW_MGR_MEM_IF_READ_DQS_WIDTH / + RW_MGR_MEM_IF_WRITE_DQS_WIDTH))); + stop = (bit_chk == 0); + } + sticky_bit_chk = sticky_bit_chk | bit_chk; + stop = stop && (sticky_bit_chk == param->read_correct_mask); + + debug_cond(DLEVEL == 2, "%s:%d vfifo_center(right): dtap=%u => %u == \ + %u && %u", __func__, __LINE__, d, + sticky_bit_chk, param->read_correct_mask, stop); + + if (stop == 1) { + break; + } else { + for (i = 0; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) { + if (bit_chk & 1) { + /* Remember a passing test as + the right_edge */ + right_edge[i] = d; + } else { + if (d != 0) { + /* If a right edge has not been + seen yet, then a future passing + test will mark this edge as the + left edge */ + if (right_edge[i] == + IO_IO_IN_DELAY_MAX + 1) { + left_edge[i] = -(d + 1); + } + } else { + /* d = 0 failed, but it passed + when testing the left edge, + so it must be marginal, + set it to -1 */ + if (right_edge[i] == + IO_IO_IN_DELAY_MAX + 1 && + left_edge[i] != + IO_IO_IN_DELAY_MAX + + 1) { + right_edge[i] = -1; + } + /* If a right edge has not been + seen yet, then a future passing + test will mark this edge as the + left edge */ + else if (right_edge[i] == + IO_IO_IN_DELAY_MAX + + 1) { + left_edge[i] = -(d + 1); + } + } + } + + debug_cond(DLEVEL == 2, "%s:%d vfifo_center[r,\ + d=%u]: ", __func__, __LINE__, d); + debug_cond(DLEVEL == 2, "bit_chk_test=%d left_edge[%u]: %d ", + (int)(bit_chk & 1), i, left_edge[i]); + debug_cond(DLEVEL == 2, "right_edge[%u]: %d\n", i, + right_edge[i]); + bit_chk = bit_chk >> 1; + } + } + } + + /* Check that all bits have a window */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + for (i = 0; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) { + debug_cond(DLEVEL == 2, "%s:%d vfifo_center: left_edge[%u]: \ + %d right_edge[%u]: %d", __func__, __LINE__, + i, left_edge[i], i, right_edge[i]); + if ((left_edge[i] == IO_IO_IN_DELAY_MAX + 1) || (right_edge[i] + == IO_IO_IN_DELAY_MAX + 1)) { + /* + * Restore delay chain settings before letting the loop + * in rw_mgr_mem_calibrate_vfifo to retry different + * dqs/ck relationships. + */ + scc_mgr_set_dqs_bus_in_delay(read_group, start_dqs); + if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS) { + scc_mgr_set_dqs_en_delay(read_group, + start_dqs_en); + } + scc_mgr_load_dqs(read_group); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + debug_cond(DLEVEL == 1, "%s:%d vfifo_center: failed to \ + find edge [%u]: %d %d", __func__, __LINE__, + i, left_edge[i], right_edge[i]); + if (use_read_test) { + set_failing_group_stage(read_group * + RW_MGR_MEM_DQ_PER_READ_DQS + i, + CAL_STAGE_VFIFO, + CAL_SUBSTAGE_VFIFO_CENTER); + } else { + set_failing_group_stage(read_group * + RW_MGR_MEM_DQ_PER_READ_DQS + i, + CAL_STAGE_VFIFO_AFTER_WRITES, + CAL_SUBSTAGE_VFIFO_CENTER); + } + return 0; + } + } + + /* Find middle of window for each DQ bit */ + mid_min = left_edge[0] - right_edge[0]; + min_index = 0; + for (i = 1; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) { + mid = left_edge[i] - right_edge[i]; + if (mid < mid_min) { + mid_min = mid; + min_index = i; + } + } + + /* + * -mid_min/2 represents the amount that we need to move DQS. + * If mid_min is odd and positive we'll need to add one to + * make sure the rounding in further calculations is correct + * (always bias to the right), so just add 1 for all positive values. + */ + if (mid_min > 0) + mid_min++; + + mid_min = mid_min / 2; + + debug_cond(DLEVEL == 1, "%s:%d vfifo_center: mid_min=%d (index=%u)\n", + __func__, __LINE__, mid_min, min_index); + + /* Determine the amount we can change DQS (which is -mid_min) */ + orig_mid_min = mid_min; + new_dqs = start_dqs - mid_min; + if (new_dqs > IO_DQS_IN_DELAY_MAX) + new_dqs = IO_DQS_IN_DELAY_MAX; + else if (new_dqs < 0) + new_dqs = 0; + + mid_min = start_dqs - new_dqs; + debug_cond(DLEVEL == 1, "vfifo_center: new mid_min=%d new_dqs=%d\n", + mid_min, new_dqs); + + if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS) { + if (start_dqs_en - mid_min > IO_DQS_EN_DELAY_MAX) + mid_min += start_dqs_en - mid_min - IO_DQS_EN_DELAY_MAX; + else if (start_dqs_en - mid_min < 0) + mid_min += start_dqs_en - mid_min; + } + new_dqs = start_dqs - mid_min; + + debug_cond(DLEVEL == 1, "vfifo_center: start_dqs=%d start_dqs_en=%d \ + new_dqs=%d mid_min=%d\n", start_dqs, + IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS ? start_dqs_en : -1, + new_dqs, mid_min); + + /* Initialize data for export structures */ + dqs_margin = IO_IO_IN_DELAY_MAX + 1; + dq_margin = IO_IO_IN_DELAY_MAX + 1; + + addr = sdr_get_addr((u32 *)SCC_MGR_IO_IN_DELAY); + /* add delay to bring centre of all DQ windows to the same "level" */ + for (i = 0, p = test_bgn; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++, p++) { + /* Use values before divide by 2 to reduce round off error */ + shift_dq = (left_edge[i] - right_edge[i] - + (left_edge[min_index] - right_edge[min_index]))/2 + + (orig_mid_min - mid_min); + + debug_cond(DLEVEL == 2, "vfifo_center: before: \ + shift_dq[%u]=%d\n", i, shift_dq); + + temp_dq_in_delay1 = readl(SOCFPGA_SDR_ADDRESS + addr + (p << 2)); + temp_dq_in_delay2 = readl(SOCFPGA_SDR_ADDRESS + addr + (i << 2)); + + if (shift_dq + (int32_t)temp_dq_in_delay1 > + (int32_t)IO_IO_IN_DELAY_MAX) { + shift_dq = (int32_t)IO_IO_IN_DELAY_MAX - temp_dq_in_delay2; + } else if (shift_dq + (int32_t)temp_dq_in_delay1 < 0) { + shift_dq = -(int32_t)temp_dq_in_delay1; + } + debug_cond(DLEVEL == 2, "vfifo_center: after: \ + shift_dq[%u]=%d\n", i, shift_dq); + final_dq[i] = temp_dq_in_delay1 + shift_dq; + scc_mgr_set_dq_in_delay(write_group, p, final_dq[i]); + scc_mgr_load_dq(p); + + debug_cond(DLEVEL == 2, "vfifo_center: margin[%u]=[%d,%d]\n", i, + left_edge[i] - shift_dq + (-mid_min), + right_edge[i] + shift_dq - (-mid_min)); + /* To determine values for export structures */ + if (left_edge[i] - shift_dq + (-mid_min) < dq_margin) + dq_margin = left_edge[i] - shift_dq + (-mid_min); + + if (right_edge[i] + shift_dq - (-mid_min) < dqs_margin) + dqs_margin = right_edge[i] + shift_dq - (-mid_min); + } + + final_dqs = new_dqs; + if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS) + final_dqs_en = start_dqs_en - mid_min; + + /* Move DQS-en */ + if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS) { + scc_mgr_set_dqs_en_delay(read_group, final_dqs_en); + scc_mgr_load_dqs(read_group); + } + + /* Move DQS */ + scc_mgr_set_dqs_bus_in_delay(read_group, final_dqs); + scc_mgr_load_dqs(read_group); + debug_cond(DLEVEL == 2, "%s:%d vfifo_center: dq_margin=%d \ + dqs_margin=%d", __func__, __LINE__, + dq_margin, dqs_margin); + + /* + * Do not remove this line as it makes sure all of our decisions + * have been applied. Apply the update bit. + */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + return (dq_margin >= 0) && (dqs_margin >= 0); +} + +/* + * calibrate the read valid prediction FIFO. + * + * - read valid prediction will consist of finding a good DQS enable phase, + * DQS enable delay, DQS input phase, and DQS input delay. + * - we also do a per-bit deskew on the DQ lines. + */ +static uint32_t rw_mgr_mem_calibrate_vfifo(uint32_t read_group, + uint32_t test_bgn) +{ + uint32_t p, d, rank_bgn, sr; + uint32_t dtaps_per_ptap; + uint32_t tmp_delay; + uint32_t bit_chk; + uint32_t grp_calibrated; + uint32_t write_group, write_test_bgn; + uint32_t failed_substage; + + debug("%s:%d: %u %u", __func__, __LINE__, read_group, test_bgn); + + /* update info for sims */ + reg_file_set_stage(CAL_STAGE_VFIFO); + + write_group = read_group; + write_test_bgn = test_bgn; + + /* USER Determine number of delay taps for each phase tap */ + dtaps_per_ptap = 0; + tmp_delay = 0; + while (tmp_delay < IO_DELAY_PER_OPA_TAP) { + dtaps_per_ptap++; + tmp_delay += IO_DELAY_PER_DQS_EN_DCHAIN_TAP; + } + dtaps_per_ptap--; + tmp_delay = 0; + + /* update info for sims */ + reg_file_set_group(read_group); + + grp_calibrated = 0; + + reg_file_set_sub_stage(CAL_SUBSTAGE_GUARANTEED_READ); + failed_substage = CAL_SUBSTAGE_GUARANTEED_READ; + + for (d = 0; d <= dtaps_per_ptap && grp_calibrated == 0; d += 2) { + /* + * In RLDRAMX we may be messing the delay of pins in + * the same write group but outside of the current read + * the group, but that's ok because we haven't + * calibrated output side yet. + */ + if (d > 0) { + scc_mgr_apply_group_all_out_delay_add_all_ranks + (write_group, write_test_bgn, d); + } + + for (p = 0; p <= IO_DQDQS_OUT_PHASE_MAX && grp_calibrated == 0; + p++) { + /* set a particular dqdqs phase */ + scc_mgr_set_dqdqs_output_phase_all_ranks(read_group, p); + + debug_cond(DLEVEL == 1, "%s:%d calibrate_vfifo: g=%u \ + p=%u d=%u\n", __func__, __LINE__, + read_group, p, d); + + /* + * Load up the patterns used by read calibration + * using current DQDQS phase. + */ + rw_mgr_mem_calibrate_read_load_patterns(0, 1); + if (!(gbl->phy_debug_mode_flags & + PHY_DEBUG_DISABLE_GUARANTEED_READ)) { + if (!rw_mgr_mem_calibrate_read_test_patterns_all_ranks + (read_group, 1, &bit_chk)) { + debug_cond(DLEVEL == 1, "%s:%d Guaranteed read test failed:", + __func__, __LINE__); + debug_cond(DLEVEL == 1, " g=%u p=%u d=%u\n", + read_group, p, d); + break; + } + } + +/* case:56390 */ + grp_calibrated = 1; + if (rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase_sweep_dq_in_delay + (write_group, read_group, test_bgn)) { + /* + * USER Read per-bit deskew can be done on a + * per shadow register basis. + */ + for (rank_bgn = 0, sr = 0; + rank_bgn < RW_MGR_MEM_NUMBER_OF_RANKS; + rank_bgn += NUM_RANKS_PER_SHADOW_REG, + ++sr) { + /* + * Determine if this set of ranks + * should be skipped entirely. + */ + if (!param->skip_shadow_regs[sr]) { + /* + * If doing read after write + * calibration, do not update + * FOM, now - do it then. + */ + if (!rw_mgr_mem_calibrate_vfifo_center + (rank_bgn, write_group, + read_group, test_bgn, 1, 0)) { + grp_calibrated = 0; + failed_substage = + CAL_SUBSTAGE_VFIFO_CENTER; + } + } + } + } else { + grp_calibrated = 0; + failed_substage = CAL_SUBSTAGE_DQS_EN_PHASE; + } + } + } + + if (grp_calibrated == 0) { + set_failing_group_stage(write_group, CAL_STAGE_VFIFO, + failed_substage); + return 0; + } + + /* + * Reset the delay chains back to zero if they have moved > 1 + * (check for > 1 because loop will increase d even when pass in + * first case). + */ + if (d > 2) + scc_mgr_zero_group(write_group, write_test_bgn, 1); + + return 1; +} + +/* VFIFO Calibration -- Read Deskew Calibration after write deskew */ +static uint32_t rw_mgr_mem_calibrate_vfifo_end(uint32_t read_group, + uint32_t test_bgn) +{ + uint32_t rank_bgn, sr; + uint32_t grp_calibrated; + uint32_t write_group; + + debug("%s:%d %u %u", __func__, __LINE__, read_group, test_bgn); + + /* update info for sims */ + + reg_file_set_stage(CAL_STAGE_VFIFO_AFTER_WRITES); + reg_file_set_sub_stage(CAL_SUBSTAGE_VFIFO_CENTER); + + write_group = read_group; + + /* update info for sims */ + reg_file_set_group(read_group); + + grp_calibrated = 1; + /* Read per-bit deskew can be done on a per shadow register basis */ + for (rank_bgn = 0, sr = 0; rank_bgn < RW_MGR_MEM_NUMBER_OF_RANKS; + rank_bgn += NUM_RANKS_PER_SHADOW_REG, ++sr) { + /* Determine if this set of ranks should be skipped entirely */ + if (!param->skip_shadow_regs[sr]) { + /* This is the last calibration round, update FOM here */ + if (!rw_mgr_mem_calibrate_vfifo_center(rank_bgn, + write_group, + read_group, + test_bgn, 0, + 1)) { + grp_calibrated = 0; + } + } + } + + + if (grp_calibrated == 0) { + set_failing_group_stage(write_group, + CAL_STAGE_VFIFO_AFTER_WRITES, + CAL_SUBSTAGE_VFIFO_CENTER); + return 0; + } + + return 1; +} + +/* Calibrate LFIFO to find smallest read latency */ +static uint32_t rw_mgr_mem_calibrate_lfifo(void) +{ + uint32_t found_one; + uint32_t bit_chk; + uint32_t addr; + + debug("%s:%d\n", __func__, __LINE__); + + /* update info for sims */ + reg_file_set_stage(CAL_STAGE_LFIFO); + reg_file_set_sub_stage(CAL_SUBSTAGE_READ_LATENCY); + + /* Load up the patterns used by read calibration for all ranks */ + rw_mgr_mem_calibrate_read_load_patterns(0, 1); + found_one = 0; + + addr = sdr_get_addr(&phy_mgr_cfg->phy_rlat); + do { + writel(gbl->curr_read_lat, SOCFPGA_SDR_ADDRESS + addr); + debug_cond(DLEVEL == 2, "%s:%d lfifo: read_lat=%u", + __func__, __LINE__, gbl->curr_read_lat); + + if (!rw_mgr_mem_calibrate_read_test_all_ranks(0, + NUM_READ_TESTS, + PASS_ALL_BITS, + &bit_chk, 1)) { + break; + } + + found_one = 1; + /* reduce read latency and see if things are working */ + /* correctly */ + gbl->curr_read_lat--; + } while (gbl->curr_read_lat > 0); + + /* reset the fifos to get pointers to known state */ + + addr = sdr_get_addr(&phy_mgr_cmd->fifo_reset); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + if (found_one) { + /* add a fudge factor to the read latency that was determined */ + gbl->curr_read_lat += 2; + addr = sdr_get_addr(&phy_mgr_cfg->phy_rlat); + writel(gbl->curr_read_lat, SOCFPGA_SDR_ADDRESS + addr); + debug_cond(DLEVEL == 2, "%s:%d lfifo: success: using \ + read_lat=%u\n", __func__, __LINE__, + gbl->curr_read_lat); + return 1; + } else { + set_failing_group_stage(0xff, CAL_STAGE_LFIFO, + CAL_SUBSTAGE_READ_LATENCY); + + debug_cond(DLEVEL == 2, "%s:%d lfifo: failed at initial \ + read_lat=%u\n", __func__, __LINE__, + gbl->curr_read_lat); + return 0; + } +} + +/* + * issue write test command. + * two variants are provided. one that just tests a write pattern and + * another that tests datamask functionality. + */ +static void rw_mgr_mem_calibrate_write_test_issue(uint32_t group, + uint32_t test_dm) +{ + uint32_t mcc_instruction; + uint32_t quick_write_mode = (((STATIC_CALIB_STEPS) & CALIB_SKIP_WRITES) && + ENABLE_SUPER_QUICK_CALIBRATION); + uint32_t rw_wl_nop_cycles; + uint32_t addr; + + /* + * Set counter and jump addresses for the right + * number of NOP cycles. + * The number of supported NOP cycles can range from -1 to infinity + * Three different cases are handled: + * + * 1. For a number of NOP cycles greater than 0, the RW Mgr looping + * mechanism will be used to insert the right number of NOPs + * + * 2. For a number of NOP cycles equals to 0, the micro-instruction + * issuing the write command will jump straight to the + * micro-instruction that turns on DQS (for DDRx), or outputs write + * data (for RLD), skipping + * the NOP micro-instruction all together + * + * 3. A number of NOP cycles equal to -1 indicates that DQS must be + * turned on in the same micro-instruction that issues the write + * command. Then we need + * to directly jump to the micro-instruction that sends out the data + * + * NOTE: Implementing this mechanism uses 2 RW Mgr jump-counters + * (2 and 3). One jump-counter (0) is used to perform multiple + * write-read operations. + * one counter left to issue this command in "multiple-group" mode + */ + + rw_wl_nop_cycles = gbl->rw_wl_nop_cycles; + + if (rw_wl_nop_cycles == -1) { + /* + * CNTR 2 - We want to execute the special write operation that + * turns on DQS right away and then skip directly to the + * instruction that sends out the data. We set the counter to a + * large number so that the jump is always taken. + */ + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr2); + writel(0xFF, SOCFPGA_SDR_ADDRESS + addr); + + /* CNTR 3 - Not used */ + if (test_dm) { + mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0_WL_1; + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add2); + writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_DATA, + SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add3); + writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP, + SOCFPGA_SDR_ADDRESS + addr); + } else { + mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0_WL_1; + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add2); + writel(RW_MGR_LFSR_WR_RD_BANK_0_DATA, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add3); + writel(RW_MGR_LFSR_WR_RD_BANK_0_NOP, SOCFPGA_SDR_ADDRESS + addr); + } + } else if (rw_wl_nop_cycles == 0) { + /* + * CNTR 2 - We want to skip the NOP operation and go straight + * to the DQS enable instruction. We set the counter to a large + * number so that the jump is always taken. + */ + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr2); + writel(0xFF, SOCFPGA_SDR_ADDRESS + addr); + + /* CNTR 3 - Not used */ + if (test_dm) { + mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0; + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add2); + writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_DQS, + SOCFPGA_SDR_ADDRESS + addr); + } else { + mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0; + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add2); + writel(RW_MGR_LFSR_WR_RD_BANK_0_DQS, SOCFPGA_SDR_ADDRESS + addr); + } + } else { + /* + * CNTR 2 - In this case we want to execute the next instruction + * and NOT take the jump. So we set the counter to 0. The jump + * address doesn't count. + */ + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr2); + writel(0x0, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add2); + writel(0x0, SOCFPGA_SDR_ADDRESS + addr); + + /* + * CNTR 3 - Set the nop counter to the number of cycles we + * need to loop for, minus 1. + */ + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr3); + writel(rw_wl_nop_cycles - 1, SOCFPGA_SDR_ADDRESS + addr); + if (test_dm) { + mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0; + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add3); + writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP, SOCFPGA_SDR_ADDRESS + addr); + } else { + mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0; + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add3); + writel(RW_MGR_LFSR_WR_RD_BANK_0_NOP, SOCFPGA_SDR_ADDRESS + addr); + } + } + + addr = sdr_get_addr((u32 *)RW_MGR_RESET_READ_DATAPATH); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr0); + if (quick_write_mode) + writel(0x08, SOCFPGA_SDR_ADDRESS + addr); + else + writel(0x40, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add0); + writel(mcc_instruction, SOCFPGA_SDR_ADDRESS + addr); + + /* + * CNTR 1 - This is used to ensure enough time elapses + * for read data to come back. + */ + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr1); + writel(0x30, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add1); + if (test_dm) { + writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_WAIT, SOCFPGA_SDR_ADDRESS + addr); + } else { + writel(RW_MGR_LFSR_WR_RD_BANK_0_WAIT, SOCFPGA_SDR_ADDRESS + addr); + } + + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(mcc_instruction, SOCFPGA_SDR_ADDRESS + addr + (group << 2)); +} + +/* Test writes, can check for a single bit pass or multiple bit pass */ +static uint32_t rw_mgr_mem_calibrate_write_test(uint32_t rank_bgn, + uint32_t write_group, uint32_t use_dm, uint32_t all_correct, + uint32_t *bit_chk, uint32_t all_ranks) +{ + uint32_t addr; + uint32_t r; + uint32_t correct_mask_vg; + uint32_t tmp_bit_chk; + uint32_t vg; + uint32_t rank_end = all_ranks ? RW_MGR_MEM_NUMBER_OF_RANKS : + (rank_bgn + NUM_RANKS_PER_SHADOW_REG); + uint32_t addr_rw_mgr; + uint32_t base_rw_mgr; + + *bit_chk = param->write_correct_mask; + correct_mask_vg = param->write_correct_mask_vg; + + for (r = rank_bgn; r < rank_end; r++) { + if (param->skip_ranks[r]) { + /* request to skip the rank */ + continue; + } + + /* set rank */ + set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_READ_WRITE); + + tmp_bit_chk = 0; + addr = sdr_get_addr(&phy_mgr_cmd->fifo_reset); + addr_rw_mgr = sdr_get_addr((u32 *)BASE_RW_MGR); + for (vg = RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS-1; ; vg--) { + /* reset the fifos to get pointers to known state */ + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + tmp_bit_chk = tmp_bit_chk << + (RW_MGR_MEM_DQ_PER_WRITE_DQS / + RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS); + rw_mgr_mem_calibrate_write_test_issue(write_group * + RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS+vg, + use_dm); + + base_rw_mgr = readl(SOCFPGA_SDR_ADDRESS + addr_rw_mgr); + tmp_bit_chk = tmp_bit_chk | (correct_mask_vg & ~(base_rw_mgr)); + if (vg == 0) + break; + } + *bit_chk &= tmp_bit_chk; + } + + if (all_correct) { + set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF); + debug_cond(DLEVEL == 2, "write_test(%u,%u,ALL) : %u == \ + %u => %lu", write_group, use_dm, + *bit_chk, param->write_correct_mask, + (long unsigned int)(*bit_chk == + param->write_correct_mask)); + return *bit_chk == param->write_correct_mask; + } else { + set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF); + debug_cond(DLEVEL == 2, "write_test(%u,%u,ONE) : %u != ", + write_group, use_dm, *bit_chk); + debug_cond(DLEVEL == 2, "%lu" " => %lu", (long unsigned int)0, + (long unsigned int)(*bit_chk != 0)); + return *bit_chk != 0x00; + } +} + +/* + * center all windows. do per-bit-deskew to possibly increase size of + * certain windows. + */ +static uint32_t rw_mgr_mem_calibrate_writes_center(uint32_t rank_bgn, + uint32_t write_group, uint32_t test_bgn) +{ + uint32_t i, p, min_index; + int32_t d; + /* + * Store these as signed since there are comparisons with + * signed numbers. + */ + uint32_t bit_chk; + uint32_t sticky_bit_chk; + int32_t left_edge[RW_MGR_MEM_DQ_PER_WRITE_DQS]; + int32_t right_edge[RW_MGR_MEM_DQ_PER_WRITE_DQS]; + int32_t mid; + int32_t mid_min, orig_mid_min; + int32_t new_dqs, start_dqs, shift_dq; + int32_t dq_margin, dqs_margin, dm_margin; + uint32_t stop; + uint32_t temp_dq_out1_delay; + uint32_t addr; + + debug("%s:%d %u %u", __func__, __LINE__, write_group, test_bgn); + + dm_margin = 0; + + addr = sdr_get_addr((u32 *)SCC_MGR_IO_OUT1_DELAY); + start_dqs = readl(SOCFPGA_SDR_ADDRESS + addr + + (RW_MGR_MEM_DQ_PER_WRITE_DQS << 2)); + + /* per-bit deskew */ + + /* + * set the left and right edge of each bit to an illegal value + * use (IO_IO_OUT1_DELAY_MAX + 1) as an illegal value. + */ + sticky_bit_chk = 0; + for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) { + left_edge[i] = IO_IO_OUT1_DELAY_MAX + 1; + right_edge[i] = IO_IO_OUT1_DELAY_MAX + 1; + } + + /* Search for the left edge of the window for each bit */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + for (d = 0; d <= IO_IO_OUT1_DELAY_MAX; d++) { + scc_mgr_apply_group_dq_out1_delay(write_group, test_bgn, d); + + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* + * Stop searching when the read test doesn't pass AND when + * we've seen a passing read on every bit. + */ + stop = !rw_mgr_mem_calibrate_write_test(rank_bgn, write_group, + 0, PASS_ONE_BIT, &bit_chk, 0); + sticky_bit_chk = sticky_bit_chk | bit_chk; + stop = stop && (sticky_bit_chk == param->write_correct_mask); + debug_cond(DLEVEL == 2, "write_center(left): dtap=%d => %u \ + == %u && %u [bit_chk= %u ]\n", + d, sticky_bit_chk, param->write_correct_mask, + stop, bit_chk); + + if (stop == 1) { + break; + } else { + for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) { + if (bit_chk & 1) { + /* + * Remember a passing test as the + * left_edge. + */ + left_edge[i] = d; + } else { + /* + * If a left edge has not been seen + * yet, then a future passing test will + * mark this edge as the right edge. + */ + if (left_edge[i] == + IO_IO_OUT1_DELAY_MAX + 1) { + right_edge[i] = -(d + 1); + } + } + debug_cond(DLEVEL == 2, "write_center[l,d=%d):", d); + debug_cond(DLEVEL == 2, "bit_chk_test=%d left_edge[%u]: %d", + (int)(bit_chk & 1), i, left_edge[i]); + debug_cond(DLEVEL == 2, "right_edge[%u]: %d\n", i, + right_edge[i]); + bit_chk = bit_chk >> 1; + } + } + } + + /* Reset DQ delay chains to 0 */ + scc_mgr_apply_group_dq_out1_delay(write_group, test_bgn, 0); + sticky_bit_chk = 0; + for (i = RW_MGR_MEM_DQ_PER_WRITE_DQS - 1;; i--) { + debug_cond(DLEVEL == 2, "%s:%d write_center: left_edge[%u]: \ + %d right_edge[%u]: %d\n", __func__, __LINE__, + i, left_edge[i], i, right_edge[i]); + + /* + * Check for cases where we haven't found the left edge, + * which makes our assignment of the the right edge invalid. + * Reset it to the illegal value. + */ + if ((left_edge[i] == IO_IO_OUT1_DELAY_MAX + 1) && + (right_edge[i] != IO_IO_OUT1_DELAY_MAX + 1)) { + right_edge[i] = IO_IO_OUT1_DELAY_MAX + 1; + debug_cond(DLEVEL == 2, "%s:%d write_center: reset \ + right_edge[%u]: %d\n", __func__, __LINE__, + i, right_edge[i]); + } + + /* + * Reset sticky bit (except for bits where we have + * seen the left edge). + */ + sticky_bit_chk = sticky_bit_chk << 1; + if ((left_edge[i] != IO_IO_OUT1_DELAY_MAX + 1)) + sticky_bit_chk = sticky_bit_chk | 1; + + if (i == 0) + break; + } + + /* Search for the right edge of the window for each bit */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + for (d = 0; d <= IO_IO_OUT1_DELAY_MAX - start_dqs; d++) { + scc_mgr_apply_group_dqs_io_and_oct_out1(write_group, + d + start_dqs); + + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* + * Stop searching when the read test doesn't pass AND when + * we've seen a passing read on every bit. + */ + stop = !rw_mgr_mem_calibrate_write_test(rank_bgn, write_group, + 0, PASS_ONE_BIT, &bit_chk, 0); + + sticky_bit_chk = sticky_bit_chk | bit_chk; + stop = stop && (sticky_bit_chk == param->write_correct_mask); + + debug_cond(DLEVEL == 2, "write_center (right): dtap=%u => %u == \ + %u && %u\n", d, sticky_bit_chk, + param->write_correct_mask, stop); + + if (stop == 1) { + if (d == 0) { + for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; + i++) { + /* d = 0 failed, but it passed when + testing the left edge, so it must be + marginal, set it to -1 */ + if (right_edge[i] == + IO_IO_OUT1_DELAY_MAX + 1 && + left_edge[i] != + IO_IO_OUT1_DELAY_MAX + 1) { + right_edge[i] = -1; + } + } + } + break; + } else { + for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) { + if (bit_chk & 1) { + /* + * Remember a passing test as + * the right_edge. + */ + right_edge[i] = d; + } else { + if (d != 0) { + /* + * If a right edge has not + * been seen yet, then a future + * passing test will mark this + * edge as the left edge. + */ + if (right_edge[i] == + IO_IO_OUT1_DELAY_MAX + 1) + left_edge[i] = -(d + 1); + } else { + /* + * d = 0 failed, but it passed + * when testing the left edge, + * so it must be marginal, set + * it to -1. + */ + if (right_edge[i] == + IO_IO_OUT1_DELAY_MAX + 1 && + left_edge[i] != + IO_IO_OUT1_DELAY_MAX + 1) + right_edge[i] = -1; + /* + * If a right edge has not been + * seen yet, then a future + * passing test will mark this + * edge as the left edge. + */ + else if (right_edge[i] == + IO_IO_OUT1_DELAY_MAX + + 1) + left_edge[i] = -(d + 1); + } + } + debug_cond(DLEVEL == 2, "write_center[r,d=%d):", d); + debug_cond(DLEVEL == 2, "bit_chk_test=%d left_edge[%u]: %d", + (int)(bit_chk & 1), i, left_edge[i]); + debug_cond(DLEVEL == 2, "right_edge[%u]: %d\n", i, + right_edge[i]); + bit_chk = bit_chk >> 1; + } + } + } + + /* Check that all bits have a window */ + for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) { + debug_cond(DLEVEL == 2, "%s:%d write_center: left_edge[%u]: \ + %d right_edge[%u]: %d", __func__, __LINE__, + i, left_edge[i], i, right_edge[i]); + if ((left_edge[i] == IO_IO_OUT1_DELAY_MAX + 1) || + (right_edge[i] == IO_IO_OUT1_DELAY_MAX + 1)) { + set_failing_group_stage(test_bgn + i, + CAL_STAGE_WRITES, + CAL_SUBSTAGE_WRITES_CENTER); + return 0; + } + } + + /* Find middle of window for each DQ bit */ + mid_min = left_edge[0] - right_edge[0]; + min_index = 0; + for (i = 1; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) { + mid = left_edge[i] - right_edge[i]; + if (mid < mid_min) { + mid_min = mid; + min_index = i; + } + } + + /* + * -mid_min/2 represents the amount that we need to move DQS. + * If mid_min is odd and positive we'll need to add one to + * make sure the rounding in further calculations is correct + * (always bias to the right), so just add 1 for all positive values. + */ + if (mid_min > 0) + mid_min++; + mid_min = mid_min / 2; + debug_cond(DLEVEL == 1, "%s:%d write_center: mid_min=%d\n", __func__, + __LINE__, mid_min); + + /* Determine the amount we can change DQS (which is -mid_min) */ + orig_mid_min = mid_min; + new_dqs = start_dqs; + mid_min = 0; + debug_cond(DLEVEL == 1, "%s:%d write_center: start_dqs=%d new_dqs=%d \ + mid_min=%d\n", __func__, __LINE__, start_dqs, new_dqs, mid_min); + /* Initialize data for export structures */ + dqs_margin = IO_IO_OUT1_DELAY_MAX + 1; + dq_margin = IO_IO_OUT1_DELAY_MAX + 1; + + /* add delay to bring centre of all DQ windows to the same "level" */ + addr = sdr_get_addr((u32 *)SCC_MGR_IO_OUT1_DELAY); + for (i = 0, p = test_bgn; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++, p++) { + /* Use values before divide by 2 to reduce round off error */ + shift_dq = (left_edge[i] - right_edge[i] - + (left_edge[min_index] - right_edge[min_index]))/2 + + (orig_mid_min - mid_min); + + debug_cond(DLEVEL == 2, "%s:%d write_center: before: shift_dq \ + [%u]=%d\n", __func__, __LINE__, i, shift_dq); + + temp_dq_out1_delay = readl(SOCFPGA_SDR_ADDRESS + addr + (i << 2)); + if (shift_dq + (int32_t)temp_dq_out1_delay > + (int32_t)IO_IO_OUT1_DELAY_MAX) { + shift_dq = (int32_t)IO_IO_OUT1_DELAY_MAX - temp_dq_out1_delay; + } else if (shift_dq + (int32_t)temp_dq_out1_delay < 0) { + shift_dq = -(int32_t)temp_dq_out1_delay; + } + debug_cond(DLEVEL == 2, "write_center: after: shift_dq[%u]=%d\n", + i, shift_dq); + scc_mgr_set_dq_out1_delay(write_group, i, temp_dq_out1_delay + + shift_dq); + scc_mgr_load_dq(i); + + debug_cond(DLEVEL == 2, "write_center: margin[%u]=[%d,%d]\n", i, + left_edge[i] - shift_dq + (-mid_min), + right_edge[i] + shift_dq - (-mid_min)); + /* To determine values for export structures */ + if (left_edge[i] - shift_dq + (-mid_min) < dq_margin) + dq_margin = left_edge[i] - shift_dq + (-mid_min); + + if (right_edge[i] + shift_dq - (-mid_min) < dqs_margin) + dqs_margin = right_edge[i] + shift_dq - (-mid_min); + } + + /* Move DQS */ + scc_mgr_apply_group_dqs_io_and_oct_out1(write_group, new_dqs); + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* Centre DM */ + debug_cond(DLEVEL == 2, "%s:%d write_center: DM\n", __func__, __LINE__); + + /* + * set the left and right edge of each bit to an illegal value, + * use (IO_IO_OUT1_DELAY_MAX + 1) as an illegal value, + */ + left_edge[0] = IO_IO_OUT1_DELAY_MAX + 1; + right_edge[0] = IO_IO_OUT1_DELAY_MAX + 1; + int32_t bgn_curr = IO_IO_OUT1_DELAY_MAX + 1; + int32_t end_curr = IO_IO_OUT1_DELAY_MAX + 1; + int32_t bgn_best = IO_IO_OUT1_DELAY_MAX + 1; + int32_t end_best = IO_IO_OUT1_DELAY_MAX + 1; + int32_t win_best = 0; + + /* Search for the/part of the window with DM shift */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + for (d = IO_IO_OUT1_DELAY_MAX; d >= 0; d -= DELTA_D) { + scc_mgr_apply_group_dm_out1_delay(write_group, d); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + if (rw_mgr_mem_calibrate_write_test(rank_bgn, write_group, 1, + PASS_ALL_BITS, &bit_chk, + 0)) { + /* USE Set current end of the window */ + end_curr = -d; + /* + * If a starting edge of our window has not been seen + * this is our current start of the DM window. + */ + if (bgn_curr == IO_IO_OUT1_DELAY_MAX + 1) + bgn_curr = -d; + + /* + * If current window is bigger than best seen. + * Set best seen to be current window. + */ + if ((end_curr-bgn_curr+1) > win_best) { + win_best = end_curr-bgn_curr+1; + bgn_best = bgn_curr; + end_best = end_curr; + } + } else { + /* We just saw a failing test. Reset temp edge */ + bgn_curr = IO_IO_OUT1_DELAY_MAX + 1; + end_curr = IO_IO_OUT1_DELAY_MAX + 1; + } + } + + + /* Reset DM delay chains to 0 */ + scc_mgr_apply_group_dm_out1_delay(write_group, 0); + + /* + * Check to see if the current window nudges up aganist 0 delay. + * If so we need to continue the search by shifting DQS otherwise DQS + * search begins as a new search. */ + if (end_curr != 0) { + bgn_curr = IO_IO_OUT1_DELAY_MAX + 1; + end_curr = IO_IO_OUT1_DELAY_MAX + 1; + } + + /* Search for the/part of the window with DQS shifts */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + for (d = 0; d <= IO_IO_OUT1_DELAY_MAX - new_dqs; d += DELTA_D) { + /* + * Note: This only shifts DQS, so are we limiting ourselve to + * width of DQ unnecessarily. + */ + scc_mgr_apply_group_dqs_io_and_oct_out1(write_group, + d + new_dqs); + + writel(0, SOCFPGA_SDR_ADDRESS + addr); + if (rw_mgr_mem_calibrate_write_test(rank_bgn, write_group, 1, + PASS_ALL_BITS, &bit_chk, + 0)) { + /* USE Set current end of the window */ + end_curr = d; + /* + * If a beginning edge of our window has not been seen + * this is our current begin of the DM window. + */ + if (bgn_curr == IO_IO_OUT1_DELAY_MAX + 1) + bgn_curr = d; + + /* + * If current window is bigger than best seen. Set best + * seen to be current window. + */ + if ((end_curr-bgn_curr+1) > win_best) { + win_best = end_curr-bgn_curr+1; + bgn_best = bgn_curr; + end_best = end_curr; + } + } else { + /* We just saw a failing test. Reset temp edge */ + bgn_curr = IO_IO_OUT1_DELAY_MAX + 1; + end_curr = IO_IO_OUT1_DELAY_MAX + 1; + + /* Early exit optimization: if ther remaining delay + chain space is less than already seen largest window + we can exit */ + if ((win_best-1) > + (IO_IO_OUT1_DELAY_MAX - new_dqs - d)) { + break; + } + } + } + + /* assign left and right edge for cal and reporting; */ + left_edge[0] = -1*bgn_best; + right_edge[0] = end_best; + + debug_cond(DLEVEL == 2, "%s:%d dm_calib: left=%d right=%d\n", __func__, + __LINE__, left_edge[0], right_edge[0]); + + /* Move DQS (back to orig) */ + scc_mgr_apply_group_dqs_io_and_oct_out1(write_group, new_dqs); + + /* Move DM */ + + /* Find middle of window for the DM bit */ + mid = (left_edge[0] - right_edge[0]) / 2; + + /* only move right, since we are not moving DQS/DQ */ + if (mid < 0) + mid = 0; + + /* dm_marign should fail if we never find a window */ + if (win_best == 0) + dm_margin = -1; + else + dm_margin = left_edge[0] - mid; + + scc_mgr_apply_group_dm_out1_delay(write_group, mid); + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + debug_cond(DLEVEL == 2, "%s:%d dm_calib: left=%d right=%d mid=%d \ + dm_margin=%d\n", __func__, __LINE__, left_edge[0], + right_edge[0], mid, dm_margin); + /* Export values */ + gbl->fom_out += dq_margin + dqs_margin; + + debug_cond(DLEVEL == 2, "%s:%d write_center: dq_margin=%d \ + dqs_margin=%d dm_margin=%d\n", __func__, __LINE__, + dq_margin, dqs_margin, dm_margin); + + /* + * Do not remove this line as it makes sure all of our + * decisions have been applied. + */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + return (dq_margin >= 0) && (dqs_margin >= 0) && (dm_margin >= 0); +} + +/* calibrate the write operations */ +static uint32_t rw_mgr_mem_calibrate_writes(uint32_t rank_bgn, uint32_t g, + uint32_t test_bgn) +{ + /* update info for sims */ + debug("%s:%d %u %u\n", __func__, __LINE__, g, test_bgn); + + reg_file_set_stage(CAL_STAGE_WRITES); + reg_file_set_sub_stage(CAL_SUBSTAGE_WRITES_CENTER); + + reg_file_set_group(g); + + if (!rw_mgr_mem_calibrate_writes_center(rank_bgn, g, test_bgn)) { + set_failing_group_stage(g, CAL_STAGE_WRITES, + CAL_SUBSTAGE_WRITES_CENTER); + return 0; + } + + return 1; +} + +/* precharge all banks and activate row 0 in bank "000..." and bank "111..." */ +static void mem_precharge_and_activate(void) +{ + uint32_t r; + uint32_t addr; + + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; r++) { + if (param->skip_ranks[r]) { + /* request to skip the rank */ + continue; + } + + /* set rank */ + set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_OFF); + + /* precharge all banks ... */ + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_PRECHARGE_ALL, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr0); + writel(0x0F, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add0); + writel(RW_MGR_ACTIVATE_0_AND_1_WAIT1, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_rw_load_mgr_regs->load_cntr1); + writel(0x0F, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_rw_load_jump_mgr_regs->load_jump_add1); + writel(RW_MGR_ACTIVATE_0_AND_1_WAIT2, SOCFPGA_SDR_ADDRESS + addr); + + /* activate rows */ + addr = sdr_get_addr((u32 *)RW_MGR_RUN_SINGLE_GROUP); + writel(RW_MGR_ACTIVATE_0_AND_1, SOCFPGA_SDR_ADDRESS + addr); + } +} + +/* Configure various memory related parameters. */ +static void mem_config(void) +{ + uint32_t rlat, wlat; + uint32_t rw_wl_nop_cycles; + uint32_t max_latency; + uint32_t addr; + + debug("%s:%d\n", __func__, __LINE__); + /* read in write and read latency */ + addr = sdr_get_addr(&data_mgr->t_wl_add); + wlat = readl(SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&data_mgr->mem_t_add); + wlat += readl(SOCFPGA_SDR_ADDRESS + addr); + /* WL for hard phy does not include additive latency */ + + /* + * add addtional write latency to offset the address/command extra + * clock cycle. We change the AC mux setting causing AC to be delayed + * by one mem clock cycle. Only do this for DDR3 + */ + wlat = wlat + 1; + + addr = sdr_get_addr(&data_mgr->t_rl_add); + rlat = readl(SOCFPGA_SDR_ADDRESS + addr); + + rw_wl_nop_cycles = wlat - 2; + gbl->rw_wl_nop_cycles = rw_wl_nop_cycles; + + /* + * For AV/CV, lfifo is hardened and always runs at full rate so + * max latency in AFI clocks, used here, is correspondingly smaller. + */ + max_latency = (1<curr_read_lat = rlat + 16; + + if (gbl->curr_read_lat > max_latency) + gbl->curr_read_lat = max_latency; + + addr = sdr_get_addr(&phy_mgr_cfg->phy_rlat); + writel(gbl->curr_read_lat, SOCFPGA_SDR_ADDRESS + addr); + + /* advertise write latency */ + gbl->curr_write_lat = wlat; + addr = sdr_get_addr(&phy_mgr_cfg->afi_wlat); + writel(wlat - 2, SOCFPGA_SDR_ADDRESS + addr); + + /* initialize bit slips */ + mem_precharge_and_activate(); +} + +/* Set VFIFO and LFIFO to instant-on settings in skip calibration mode */ +static void mem_skip_calibrate(void) +{ + uint32_t vfifo_offset; + uint32_t i, j, r; + uint32_t addr; + + debug("%s:%d\n", __func__, __LINE__); + /* Need to update every shadow register set used by the interface */ + for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS; + r += NUM_RANKS_PER_SHADOW_REG) { + /* + * Set output phase alignment settings appropriate for + * skip calibration. + */ + for (i = 0; i < RW_MGR_MEM_IF_READ_DQS_WIDTH; i++) { + scc_mgr_set_dqs_en_phase(i, 0); +#if IO_DLL_CHAIN_LENGTH == 6 + scc_mgr_set_dqdqs_output_phase(i, 6); +#else + scc_mgr_set_dqdqs_output_phase(i, 7); +#endif + /* + * Case:33398 + * + * Write data arrives to the I/O two cycles before write + * latency is reached (720 deg). + * -> due to bit-slip in a/c bus + * -> to allow board skew where dqs is longer than ck + * -> how often can this happen!? + * -> can claim back some ptaps for high freq + * support if we can relax this, but i digress... + * + * The write_clk leads mem_ck by 90 deg + * The minimum ptap of the OPA is 180 deg + * Each ptap has (360 / IO_DLL_CHAIN_LENGH) deg of delay + * The write_clk is always delayed by 2 ptaps + * + * Hence, to make DQS aligned to CK, we need to delay + * DQS by: + * (720 - 90 - 180 - 2 * (360 / IO_DLL_CHAIN_LENGTH)) + * + * Dividing the above by (360 / IO_DLL_CHAIN_LENGTH) + * gives us the number of ptaps, which simplies to: + * + * (1.25 * IO_DLL_CHAIN_LENGTH - 2) + */ + scc_mgr_set_dqdqs_output_phase(i, (1.25 * + IO_DLL_CHAIN_LENGTH - 2)); + } + addr = sdr_get_addr(&sdr_scc_mgr->dqs_ena); + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_scc_mgr->dqs_io_ena); + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr((u32 *)SCC_MGR_GROUP_COUNTER); + for (i = 0; i < RW_MGR_MEM_IF_WRITE_DQS_WIDTH; i++) { + writel(i, SOCFPGA_SDR_ADDRESS + addr); + } + addr = sdr_get_addr(&sdr_scc_mgr->dq_ena); + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_scc_mgr->dm_ena); + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + } + + /* Compensate for simulation model behaviour */ + for (i = 0; i < RW_MGR_MEM_IF_READ_DQS_WIDTH; i++) { + scc_mgr_set_dqs_bus_in_delay(i, 10); + scc_mgr_load_dqs(i); + } + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* + * ArriaV has hard FIFOs that can only be initialized by incrementing + * in sequencer. + */ + vfifo_offset = CALIB_VFIFO_OFFSET; + addr = sdr_get_addr(&phy_mgr_cmd->inc_vfifo_hard_phy); + for (j = 0; j < vfifo_offset; j++) { + writel(0xff, SOCFPGA_SDR_ADDRESS + addr); + } + addr = sdr_get_addr(&phy_mgr_cmd->fifo_reset); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* + * For ACV with hard lfifo, we get the skip-cal setting from + * generation-time constant. + */ + gbl->curr_read_lat = CALIB_LFIFO_OFFSET; + addr = sdr_get_addr(&phy_mgr_cfg->phy_rlat); + writel(gbl->curr_read_lat, SOCFPGA_SDR_ADDRESS + addr); +} + +/* Memory calibration entry point */ +static uint32_t mem_calibrate(void) +{ + uint32_t i; + uint32_t rank_bgn, sr; + uint32_t write_group, write_test_bgn; + uint32_t read_group, read_test_bgn; + uint32_t run_groups, current_run; + uint32_t failing_groups = 0; + uint32_t group_failed = 0; + uint32_t sr_failed = 0; + uint32_t addr; + + debug("%s:%d\n", __func__, __LINE__); + /* Initialize the data settings */ + + gbl->error_substage = CAL_SUBSTAGE_NIL; + gbl->error_stage = CAL_STAGE_NIL; + gbl->error_group = 0xff; + gbl->fom_in = 0; + gbl->fom_out = 0; + + mem_config(); + + uint32_t bypass_mode = 0x1; + addr = sdr_get_addr((u32 *)SCC_MGR_GROUP_COUNTER); + for (i = 0; i < RW_MGR_MEM_IF_READ_DQS_WIDTH; i++) { + writel(i, SOCFPGA_SDR_ADDRESS + addr); + scc_set_bypass_mode(i, bypass_mode); + } + + if ((dyn_calib_steps & CALIB_SKIP_ALL) == CALIB_SKIP_ALL) { + /* + * Set VFIFO and LFIFO to instant-on settings in skip + * calibration mode. + */ + mem_skip_calibrate(); + } else { + for (i = 0; i < NUM_CALIB_REPEAT; i++) { + /* + * Zero all delay chain/phase settings for all + * groups and all shadow register sets. + */ + scc_mgr_zero_all(); + + run_groups = ~param->skip_groups; + + for (write_group = 0, write_test_bgn = 0; write_group + < RW_MGR_MEM_IF_WRITE_DQS_WIDTH; write_group++, + write_test_bgn += RW_MGR_MEM_DQ_PER_WRITE_DQS) { + /* Initialized the group failure */ + group_failed = 0; + + current_run = run_groups & ((1 << + RW_MGR_NUM_DQS_PER_WRITE_GROUP) - 1); + run_groups = run_groups >> + RW_MGR_NUM_DQS_PER_WRITE_GROUP; + + if (current_run == 0) + continue; + + addr = sdr_get_addr((u32 *)SCC_MGR_GROUP_COUNTER); + writel(write_group, SOCFPGA_SDR_ADDRESS + addr); + scc_mgr_zero_group(write_group, write_test_bgn, + 0); + + for (read_group = write_group * + RW_MGR_MEM_IF_READ_DQS_WIDTH / + RW_MGR_MEM_IF_WRITE_DQS_WIDTH, + read_test_bgn = 0; + read_group < (write_group + 1) * + RW_MGR_MEM_IF_READ_DQS_WIDTH / + RW_MGR_MEM_IF_WRITE_DQS_WIDTH && + group_failed == 0; + read_group++, read_test_bgn += + RW_MGR_MEM_DQ_PER_READ_DQS) { + /* Calibrate the VFIFO */ + if (!((STATIC_CALIB_STEPS) & + CALIB_SKIP_VFIFO)) { + if (!rw_mgr_mem_calibrate_vfifo + (read_group, + read_test_bgn)) { + group_failed = 1; + + if (!(gbl-> + phy_debug_mode_flags & + PHY_DEBUG_SWEEP_ALL_GROUPS)) { + return 0; + } + } + } + } + + /* Calibrate the output side */ + if (group_failed == 0) { + for (rank_bgn = 0, sr = 0; rank_bgn + < RW_MGR_MEM_NUMBER_OF_RANKS; + rank_bgn += + NUM_RANKS_PER_SHADOW_REG, + ++sr) { + sr_failed = 0; + if (!((STATIC_CALIB_STEPS) & + CALIB_SKIP_WRITES)) { + if ((STATIC_CALIB_STEPS) + & CALIB_SKIP_DELAY_SWEEPS) { + /* not needed in quick mode! */ + } else { + /* + * Determine if this set of + * ranks should be skipped + * entirely. + */ + if (!param->skip_shadow_regs[sr]) { + if (!rw_mgr_mem_calibrate_writes + (rank_bgn, write_group, + write_test_bgn)) { + sr_failed = 1; + if (!(gbl-> + phy_debug_mode_flags & + PHY_DEBUG_SWEEP_ALL_GROUPS)) { + return 0; + } + } + } + } + } + if (sr_failed != 0) + group_failed = 1; + } + } + + if (group_failed == 0) { + for (read_group = write_group * + RW_MGR_MEM_IF_READ_DQS_WIDTH / + RW_MGR_MEM_IF_WRITE_DQS_WIDTH, + read_test_bgn = 0; + read_group < (write_group + 1) + * RW_MGR_MEM_IF_READ_DQS_WIDTH + / RW_MGR_MEM_IF_WRITE_DQS_WIDTH && + group_failed == 0; + read_group++, read_test_bgn += + RW_MGR_MEM_DQ_PER_READ_DQS) { + if (!((STATIC_CALIB_STEPS) & + CALIB_SKIP_WRITES)) { + if (!rw_mgr_mem_calibrate_vfifo_end + (read_group, read_test_bgn)) { + group_failed = 1; + + if (!(gbl->phy_debug_mode_flags + & PHY_DEBUG_SWEEP_ALL_GROUPS)) { + return 0; + } + } + } + } + } + + if (group_failed != 0) + failing_groups++; + } + + /* + * USER If there are any failing groups then report + * the failure. + */ + if (failing_groups != 0) + return 0; + + /* Calibrate the LFIFO */ + if (!((STATIC_CALIB_STEPS) & CALIB_SKIP_LFIFO)) { + /* + * If we're skipping groups as part of debug, + * don't calibrate LFIFO. + */ + if (param->skip_groups == 0) { + if (!rw_mgr_mem_calibrate_lfifo()) + return 0; + } + } + } + } + + /* + * Do not remove this line as it makes sure all of our decisions + * have been applied. + */ + addr = sdr_get_addr(&sdr_scc_mgr->update); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + return 1; +} + +static uint32_t run_mem_calibrate(void) +{ + uint32_t pass; + uint32_t debug_info; + uint32_t addr; + + debug("%s:%d\n", __func__, __LINE__); + + /* Reset pass/fail status shown on afi_cal_success/fail */ + addr = sdr_get_addr(&phy_mgr_cfg->cal_status); + writel(PHY_MGR_CAL_RESET, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr((u32 *)BASE_MMR); + /* stop tracking manger */ + uint32_t ctrlcfg = readl(SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr((u32 *)BASE_MMR); + writel(ctrlcfg & 0xFFBFFFFF, SOCFPGA_SDR_ADDRESS + addr); + + initialize(); + rw_mgr_mem_initialize(); + + pass = mem_calibrate(); + + mem_precharge_and_activate(); + addr = sdr_get_addr(&phy_mgr_cmd->fifo_reset); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + /* + * Handoff: + * Don't return control of the PHY back to AFI when in debug mode. + */ + if ((gbl->phy_debug_mode_flags & PHY_DEBUG_IN_DEBUG_MODE) == 0) { + rw_mgr_mem_handoff(); + /* + * In Hard PHY this is a 2-bit control: + * 0: AFI Mux Select + * 1: DDIO Mux Select + */ + addr = sdr_get_addr(&phy_mgr_cfg->mux_sel); + writel(0x2, SOCFPGA_SDR_ADDRESS + addr); + } + + addr = sdr_get_addr((u32 *)BASE_MMR); + writel(ctrlcfg, SOCFPGA_SDR_ADDRESS + addr); + + if (pass) { + printf("%s: CALIBRATION PASSED\n", __FILE__); + + gbl->fom_in /= 2; + gbl->fom_out /= 2; + + if (gbl->fom_in > 0xff) + gbl->fom_in = 0xff; + + if (gbl->fom_out > 0xff) + gbl->fom_out = 0xff; + + /* Update the FOM in the register file */ + debug_info = gbl->fom_in; + debug_info |= gbl->fom_out << 8; + addr = sdr_get_addr(&sdr_reg_file->fom); + writel(debug_info, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&phy_mgr_cfg->cal_debug_info); + writel(debug_info, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&phy_mgr_cfg->cal_status); + writel(PHY_MGR_CAL_SUCCESS, SOCFPGA_SDR_ADDRESS + addr); + } else { + printf("%s: CALIBRATION FAILED\n", __FILE__); + + debug_info = gbl->error_stage; + debug_info |= gbl->error_substage << 8; + debug_info |= gbl->error_group << 16; + + addr = sdr_get_addr(&sdr_reg_file->failing_stage); + writel(debug_info, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&phy_mgr_cfg->cal_debug_info); + writel(debug_info, SOCFPGA_SDR_ADDRESS + addr); + addr = sdr_get_addr(&phy_mgr_cfg->cal_status); + writel(PHY_MGR_CAL_FAIL, SOCFPGA_SDR_ADDRESS + addr); + + /* Update the failing group/stage in the register file */ + debug_info = gbl->error_stage; + debug_info |= gbl->error_substage << 8; + debug_info |= gbl->error_group << 16; + addr = sdr_get_addr(&sdr_reg_file->failing_stage); + writel(debug_info, SOCFPGA_SDR_ADDRESS + addr); + } + + return pass; +} + +static void hc_initialize_rom_data(void) +{ + uint32_t i; + uint32_t addr; + + addr = sdr_get_addr((u32 *)(RW_MGR_INST_ROM_WRITE)); + for (i = 0; i < ARRAY_SIZE(inst_rom_init); i++) { + uint32_t data = inst_rom_init[i]; + writel(data, SOCFPGA_SDR_ADDRESS + addr + (i << 2)); + } + + addr = sdr_get_addr((u32 *)(RW_MGR_AC_ROM_WRITE)); + for (i = 0; i < ARRAY_SIZE(ac_rom_init); i++) { + uint32_t data = ac_rom_init[i]; + writel(data, SOCFPGA_SDR_ADDRESS + addr + (i << 2)); + } +} + +static void initialize_reg_file(void) +{ + uint32_t addr; + + /* Initialize the register file with the correct data */ + addr = sdr_get_addr(&sdr_reg_file->signature); + writel(REG_FILE_INIT_SEQ_SIGNATURE, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->debug_data_addr); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->cur_stage); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->fom); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->failing_stage); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->debug1); + writel(0, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->debug2); + writel(0, SOCFPGA_SDR_ADDRESS + addr); +} + +static void initialize_hps_phy(void) +{ + uint32_t reg; + uint32_t addr; + /* + * Tracking also gets configured here because it's in the + * same register. + */ + uint32_t trk_sample_count = 7500; + uint32_t trk_long_idle_sample_count = (10 << 16) | 100; + /* + * Format is number of outer loops in the 16 MSB, sample + * count in 16 LSB. + */ + + reg = 0; + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_ACDELAYEN_SET(2); + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_DQDELAYEN_SET(1); + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_DQSDELAYEN_SET(1); + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_DQSLOGICDELAYEN_SET(1); + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_RESETDELAYEN_SET(0); + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_LPDDRDIS_SET(1); + /* + * This field selects the intrinsic latency to RDATA_EN/FULL path. + * 00-bypass, 01- add 5 cycles, 10- add 10 cycles, 11- add 15 cycles. + */ + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_ADDLATSEL_SET(0); + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_SAMPLECOUNT_19_0_SET( + trk_sample_count); + addr = sdr_get_addr((u32 *)BASE_MMR); + writel(reg, SOCFPGA_SDR_ADDRESS + addr + SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_OFFSET); + + reg = 0; + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_1_SAMPLECOUNT_31_20_SET( + trk_sample_count >> + SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_SAMPLECOUNT_19_0_WIDTH); + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_1_LONGIDLESAMPLECOUNT_19_0_SET( + trk_long_idle_sample_count); + writel(reg, SOCFPGA_SDR_ADDRESS + addr + SDR_CTRLGRP_PHYCTRL_PHYCTRL_1_OFFSET); + + reg = 0; + reg |= SDR_CTRLGRP_PHYCTRL_PHYCTRL_2_LONGIDLESAMPLECOUNT_31_20_SET( + trk_long_idle_sample_count >> + SDR_CTRLGRP_PHYCTRL_PHYCTRL_1_LONGIDLESAMPLECOUNT_19_0_WIDTH); + writel(reg, SOCFPGA_SDR_ADDRESS + addr + SDR_CTRLGRP_PHYCTRL_PHYCTRL_2_OFFSET); +} + +static void initialize_tracking(void) +{ + uint32_t concatenated_longidle = 0x0; + uint32_t concatenated_delays = 0x0; + uint32_t concatenated_rw_addr = 0x0; + uint32_t concatenated_refresh = 0x0; + uint32_t trk_sample_count = 7500; + uint32_t dtaps_per_ptap; + uint32_t tmp_delay; + uint32_t addr; + + /* + * compute usable version of value in case we skip full + * computation later + */ + dtaps_per_ptap = 0; + tmp_delay = 0; + while (tmp_delay < IO_DELAY_PER_OPA_TAP) { + dtaps_per_ptap++; + tmp_delay += IO_DELAY_PER_DCHAIN_TAP; + } + dtaps_per_ptap--; + + concatenated_longidle = concatenated_longidle ^ 10; + /*longidle outer loop */ + concatenated_longidle = concatenated_longidle << 16; + concatenated_longidle = concatenated_longidle ^ 100; + /*longidle sample count */ + concatenated_delays = concatenated_delays ^ 243; + /* trfc, worst case of 933Mhz 4Gb */ + concatenated_delays = concatenated_delays << 8; + concatenated_delays = concatenated_delays ^ 14; + /* trcd, worst case */ + concatenated_delays = concatenated_delays << 8; + concatenated_delays = concatenated_delays ^ 10; + /* vfifo wait */ + concatenated_delays = concatenated_delays << 8; + concatenated_delays = concatenated_delays ^ 4; + /* mux delay */ + + concatenated_rw_addr = concatenated_rw_addr ^ RW_MGR_IDLE; + concatenated_rw_addr = concatenated_rw_addr << 8; + concatenated_rw_addr = concatenated_rw_addr ^ RW_MGR_ACTIVATE_1; + concatenated_rw_addr = concatenated_rw_addr << 8; + concatenated_rw_addr = concatenated_rw_addr ^ RW_MGR_SGLE_READ; + concatenated_rw_addr = concatenated_rw_addr << 8; + concatenated_rw_addr = concatenated_rw_addr ^ RW_MGR_PRECHARGE_ALL; + + concatenated_refresh = concatenated_refresh ^ RW_MGR_REFRESH_ALL; + concatenated_refresh = concatenated_refresh << 24; + concatenated_refresh = concatenated_refresh ^ 1000; /* trefi */ + + /* Initialize the register file with the correct data */ + addr = sdr_get_addr(&sdr_reg_file->dtaps_per_ptap); + writel(dtaps_per_ptap, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->trk_sample_count); + writel(trk_sample_count, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->trk_longidle); + writel(concatenated_longidle, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->delays); + writel(concatenated_delays, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->trk_rw_mgr_addr); + writel(concatenated_rw_addr, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->trk_read_dqs_width); + writel(RW_MGR_MEM_IF_READ_DQS_WIDTH, SOCFPGA_SDR_ADDRESS + addr); + + addr = sdr_get_addr(&sdr_reg_file->trk_rfsh); + writel(concatenated_refresh, SOCFPGA_SDR_ADDRESS + addr); +} + +int sdram_calibration_full(void) +{ + struct param_type my_param; + struct gbl_type my_gbl; + uint32_t pass; + uint32_t i; + + param = &my_param; + gbl = &my_gbl; + + /* Initialize the debug mode flags */ + gbl->phy_debug_mode_flags = 0; + /* Set the calibration enabled by default */ + gbl->phy_debug_mode_flags |= PHY_DEBUG_ENABLE_CAL_RPT; + /* + * Only sweep all groups (regardless of fail state) by default + * Set enabled read test by default. + */ +#if DISABLE_GUARANTEED_READ + gbl->phy_debug_mode_flags |= PHY_DEBUG_DISABLE_GUARANTEED_READ; +#endif + /* Initialize the register file */ + initialize_reg_file(); + + /* Initialize any PHY CSR */ + initialize_hps_phy(); + + scc_mgr_initialize(); + + initialize_tracking(); + + /* USER Enable all ranks, groups */ + for (i = 0; i < RW_MGR_MEM_NUMBER_OF_RANKS; i++) + param->skip_ranks[i] = 0; + for (i = 0; i < NUM_SHADOW_REGS; ++i) + param->skip_shadow_regs[i] = 0; + param->skip_groups = 0; + + printf("%s: Preparing to start memory calibration\n", __FILE__); + + debug("%s:%d\n", __func__, __LINE__); + debug_cond(DLEVEL == 1, "DDR3 FULL_RATE ranks=%lu cs/dimm=%lu dq/dqs=%lu,%lu vg/dqs=%lu,%lu", + (long unsigned int)RW_MGR_MEM_NUMBER_OF_RANKS, + (long unsigned int)RW_MGR_MEM_NUMBER_OF_CS_PER_DIMM, + (long unsigned int)RW_MGR_MEM_DQ_PER_READ_DQS, + (long unsigned int)RW_MGR_MEM_DQ_PER_WRITE_DQS, + (long unsigned int)RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS, + (long unsigned int)RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS); + debug_cond(DLEVEL == 1, "dqs=%lu,%lu dq=%lu dm=%lu ptap_delay=%lu dtap_delay=%lu", + (long unsigned int)RW_MGR_MEM_IF_READ_DQS_WIDTH, + (long unsigned int)RW_MGR_MEM_IF_WRITE_DQS_WIDTH, + (long unsigned int)RW_MGR_MEM_DATA_WIDTH, + (long unsigned int)RW_MGR_MEM_DATA_MASK_WIDTH, + (long unsigned int)IO_DELAY_PER_OPA_TAP, + (long unsigned int)IO_DELAY_PER_DCHAIN_TAP); + debug_cond(DLEVEL == 1, "dtap_dqsen_delay=%lu, dll=%lu", + (long unsigned int)IO_DELAY_PER_DQS_EN_DCHAIN_TAP, + (long unsigned int)IO_DLL_CHAIN_LENGTH); + debug_cond(DLEVEL == 1, "max values: en_p=%lu dqdqs_p=%lu en_d=%lu dqs_in_d=%lu", + (long unsigned int)IO_DQS_EN_PHASE_MAX, + (long unsigned int)IO_DQDQS_OUT_PHASE_MAX, + (long unsigned int)IO_DQS_EN_DELAY_MAX, + (long unsigned int)IO_DQS_IN_DELAY_MAX); + debug_cond(DLEVEL == 1, "io_in_d=%lu io_out1_d=%lu io_out2_d=%lu", + (long unsigned int)IO_IO_IN_DELAY_MAX, + (long unsigned int)IO_IO_OUT1_DELAY_MAX, + (long unsigned int)IO_IO_OUT2_DELAY_MAX); + debug_cond(DLEVEL == 1, "dqs_in_reserve=%lu dqs_out_reserve=%lu", + (long unsigned int)IO_DQS_IN_RESERVE, + (long unsigned int)IO_DQS_OUT_RESERVE); + + hc_initialize_rom_data(); + + /* update info for sims */ + reg_file_set_stage(CAL_STAGE_NIL); + reg_file_set_group(0); + + /* + * Load global needed for those actions that require + * some dynamic calibration support. + */ + dyn_calib_steps = STATIC_CALIB_STEPS; + /* + * Load global to allow dynamic selection of delay loop settings + * based on calibration mode. + */ + if (!(dyn_calib_steps & CALIB_SKIP_DELAY_LOOPS)) + skip_delay_mask = 0xff; + else + skip_delay_mask = 0x0; + + pass = run_mem_calibrate(); + + printf("%s: Calibration complete\n", __FILE__); + return pass; +} diff --git a/drivers/ddr/altera/sequencer.h b/drivers/ddr/altera/sequencer.h new file mode 100644 index 0000000..ed2bae2 --- /dev/null +++ b/drivers/ddr/altera/sequencer.h @@ -0,0 +1,322 @@ +/* + * Copyright Altera Corporation (C) 2012-2015 + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#ifndef _SEQUENCER_H_ +#define _SEQUENCER_H_ + +#define RW_MGR_NUM_DM_PER_WRITE_GROUP (RW_MGR_MEM_DATA_MASK_WIDTH \ + / RW_MGR_MEM_IF_WRITE_DQS_WIDTH) +#define RW_MGR_NUM_TRUE_DM_PER_WRITE_GROUP (RW_MGR_TRUE_MEM_DATA_MASK_WIDTH \ + / RW_MGR_MEM_IF_WRITE_DQS_WIDTH) + +#define RW_MGR_NUM_DQS_PER_WRITE_GROUP (RW_MGR_MEM_IF_READ_DQS_WIDTH \ + / RW_MGR_MEM_IF_WRITE_DQS_WIDTH) +#define NUM_RANKS_PER_SHADOW_REG (RW_MGR_MEM_NUMBER_OF_RANKS / NUM_SHADOW_REGS) + +#define RW_MGR_RUN_SINGLE_GROUP (BASE_RW_MGR) +#define RW_MGR_RUN_ALL_GROUPS (BASE_RW_MGR + 0x0400) + +#define RW_MGR_DI_BASE (BASE_RW_MGR + 0x0020) + +#define RW_MGR_MEM_NUMBER_OF_RANKS 1 +#define NUM_SHADOW_REGS 1 + +#define RW_MGR_RESET_READ_DATAPATH (BASE_RW_MGR + 0x1000) +#define RW_MGR_SET_CS_AND_ODT_MASK (BASE_RW_MGR + 0x1400) + +#define RW_MGR_RANK_NONE 0xFF +#define RW_MGR_RANK_ALL 0x00 + +#define RW_MGR_ODT_MODE_OFF 0 +#define RW_MGR_ODT_MODE_READ_WRITE 1 + +#define NUM_CALIB_REPEAT 1 + +#define NUM_READ_TESTS 7 +#define NUM_READ_PB_TESTS 7 +#define NUM_WRITE_TESTS 15 +#define NUM_WRITE_PB_TESTS 31 + +#define PASS_ALL_BITS 1 +#define PASS_ONE_BIT 0 + +/* calibration stages */ +#define CAL_STAGE_NIL 0 +#define CAL_STAGE_VFIFO 1 +#define CAL_STAGE_WLEVEL 2 +#define CAL_STAGE_LFIFO 3 +#define CAL_STAGE_WRITES 4 +#define CAL_STAGE_FULLTEST 5 +#define CAL_STAGE_REFRESH 6 +#define CAL_STAGE_CAL_SKIPPED 7 +#define CAL_STAGE_CAL_ABORTED 8 +#define CAL_STAGE_VFIFO_AFTER_WRITES 9 + +/* calibration substages */ +#define CAL_SUBSTAGE_NIL 0 +#define CAL_SUBSTAGE_GUARANTEED_READ 1 +#define CAL_SUBSTAGE_DQS_EN_PHASE 2 +#define CAL_SUBSTAGE_VFIFO_CENTER 3 +#define CAL_SUBSTAGE_WORKING_DELAY 1 +#define CAL_SUBSTAGE_LAST_WORKING_DELAY 2 +#define CAL_SUBSTAGE_WLEVEL_COPY 3 +#define CAL_SUBSTAGE_WRITES_CENTER 1 +#define CAL_SUBSTAGE_READ_LATENCY 1 +#define CAL_SUBSTAGE_REFRESH 1 + +#define MAX_RANKS (RW_MGR_MEM_NUMBER_OF_RANKS) +#define MAX_DQS (RW_MGR_MEM_IF_WRITE_DQS_WIDTH > \ + RW_MGR_MEM_IF_READ_DQS_WIDTH ? \ + RW_MGR_MEM_IF_WRITE_DQS_WIDTH : \ + RW_MGR_MEM_IF_READ_DQS_WIDTH) +#define MAX_DQ (RW_MGR_MEM_DATA_WIDTH) +#define MAX_DM (RW_MGR_MEM_DATA_MASK_WIDTH) + +/* length of VFIFO, from SW_MACROS */ +#define VFIFO_SIZE (READ_VALID_FIFO_SIZE) + +/* MarkW: how should these base addresses be done for A-V? */ +#define BASE_PTR_MGR 0x00040000 +#define BASE_SCC_MGR 0x00058000 +#define BASE_REG_FILE 0x00070000 +#define BASE_TIMER 0x00078000 +#define BASE_PHY_MGR 0x00088000 +#define BASE_RW_MGR 0x00090000 +#define BASE_DATA_MGR 0x00098000 +#define BASE_MMR 0x000C0000 +#define BASE_TRK_MGR 0x000D0000 + +#define SCC_MGR_GROUP_COUNTER (BASE_SCC_MGR + 0x0000) +#define SCC_MGR_DQS_IN_DELAY (BASE_SCC_MGR + 0x0100) +#define SCC_MGR_DQS_EN_PHASE (BASE_SCC_MGR + 0x0200) +#define SCC_MGR_DQS_EN_DELAY (BASE_SCC_MGR + 0x0300) +#define SCC_MGR_DQDQS_OUT_PHASE (BASE_SCC_MGR + 0x0400) +#define SCC_MGR_OCT_OUT1_DELAY (BASE_SCC_MGR + 0x0500) +#define SCC_MGR_IO_OUT1_DELAY (BASE_SCC_MGR + 0x0700) +#define SCC_MGR_IO_IN_DELAY (BASE_SCC_MGR + 0x0900) + +/* HHP-HPS-specific versions of some commands */ +#define SCC_MGR_DQS_EN_DELAY_GATE (BASE_SCC_MGR + 0x0600) +#define SCC_MGR_IO_OE_DELAY (BASE_SCC_MGR + 0x0800) +#define SCC_MGR_HHP_GLOBALS (BASE_SCC_MGR + 0x0A00) +#define SCC_MGR_HHP_RFILE (BASE_SCC_MGR + 0x0B00) +#define SCC_MGR_AFI_CAL_INIT (BASE_SCC_MGR + 0x0D00) + +#define SDR_PHYGRP_SCCGRP_ADDRESS 0x0 +#define SDR_PHYGRP_PHYMGRGRP_ADDRESS 0x1000 +#define SDR_PHYGRP_RWMGRGRP_ADDRESS 0x2000 +#define SDR_PHYGRP_DATAMGRGRP_ADDRESS 0x4000 +#define SDR_PHYGRP_REGFILEGRP_ADDRESS 0x4800 + +#define SDR_CTRLGRP_PHYCTRL_PHYCTRL_0_OFFSET 0x150 +#define SDR_CTRLGRP_PHYCTRL_PHYCTRL_1_OFFSET 0x154 +#define SDR_CTRLGRP_PHYCTRL_PHYCTRL_2_OFFSET 0x158 + +#define PHY_MGR_CAL_RESET (0) +#define PHY_MGR_CAL_SUCCESS (1) +#define PHY_MGR_CAL_FAIL (2) + +#define CALIB_SKIP_DELAY_LOOPS (1 << 0) +#define CALIB_SKIP_ALL_BITS_CHK (1 << 1) +#define CALIB_SKIP_DELAY_SWEEPS (1 << 2) +#define CALIB_SKIP_VFIFO (1 << 3) +#define CALIB_SKIP_LFIFO (1 << 4) +#define CALIB_SKIP_WLEVEL (1 << 5) +#define CALIB_SKIP_WRITES (1 << 6) +#define CALIB_SKIP_FULL_TEST (1 << 7) +#define CALIB_SKIP_ALL (CALIB_SKIP_VFIFO | \ + CALIB_SKIP_LFIFO | CALIB_SKIP_WLEVEL | \ + CALIB_SKIP_WRITES | CALIB_SKIP_FULL_TEST) +#define CALIB_IN_RTL_SIM (1 << 8) + +/* Scan chain manager command addresses */ +#define READ_SCC_OCT_OUT2_DELAY 0 +#define READ_SCC_DQ_OUT2_DELAY 0 +#define READ_SCC_DQS_IO_OUT2_DELAY 0 +#define READ_SCC_DM_IO_OUT2_DELAY 0 + +/* HHP-HPS-specific values */ +#define SCC_MGR_HHP_EXTRAS_OFFSET 0 +#define SCC_MGR_HHP_DQSE_MAP_OFFSET 1 + +/* PHY Debug mode flag constants */ +#define PHY_DEBUG_IN_DEBUG_MODE 0x00000001 +#define PHY_DEBUG_ENABLE_CAL_RPT 0x00000002 +#define PHY_DEBUG_ENABLE_MARGIN_RPT 0x00000004 +#define PHY_DEBUG_SWEEP_ALL_GROUPS 0x00000008 +#define PHY_DEBUG_DISABLE_GUARANTEED_READ 0x00000010 +#define PHY_DEBUG_ENABLE_NON_DESTRUCTIVE_CALIBRATION 0x00000020 + +/* Init and Reset delay constants - Only use if defined by sequencer_defines.h, + * otherwise, revert to defaults + * Default for Tinit = (0+1) * ((202+1) * (2 * 131 + 1) + 1) = 53532 = + * 200.75us @ 266MHz + */ +#ifdef TINIT_CNTR0_VAL +#define SEQ_TINIT_CNTR0_VAL TINIT_CNTR0_VAL +#else +#define SEQ_TINIT_CNTR0_VAL 0 +#endif + +#ifdef TINIT_CNTR1_VAL +#define SEQ_TINIT_CNTR1_VAL TINIT_CNTR1_VAL +#else +#define SEQ_TINIT_CNTR1_VAL 202 +#endif + +#ifdef TINIT_CNTR2_VAL +#define SEQ_TINIT_CNTR2_VAL TINIT_CNTR2_VAL +#else +#define SEQ_TINIT_CNTR2_VAL 131 +#endif + + +/* Default for Treset = (2+1) * ((252+1) * (2 * 131 + 1) + 1) = 133563 = + * 500.86us @ 266MHz + */ +#ifdef TRESET_CNTR0_VAL +#define SEQ_TRESET_CNTR0_VAL TRESET_CNTR0_VAL +#else +#define SEQ_TRESET_CNTR0_VAL 2 +#endif + +#ifdef TRESET_CNTR1_VAL +#define SEQ_TRESET_CNTR1_VAL TRESET_CNTR1_VAL +#else +#define SEQ_TRESET_CNTR1_VAL 252 +#endif + +#ifdef TRESET_CNTR2_VAL +#define SEQ_TRESET_CNTR2_VAL TRESET_CNTR2_VAL +#else +#define SEQ_TRESET_CNTR2_VAL 131 +#endif + +#define RW_MGR_INST_ROM_WRITE BASE_RW_MGR + 0x1800 +#define RW_MGR_AC_ROM_WRITE BASE_RW_MGR + 0x1C00 + +struct socfpga_sdr_rw_load_manager { + u32 load_cntr0; + u32 load_cntr1; + u32 load_cntr2; + u32 load_cntr3; +}; + +struct socfpga_sdr_rw_load_jump_manager { + u32 load_jump_add0; + u32 load_jump_add1; + u32 load_jump_add2; + u32 load_jump_add3; +}; + +struct socfpga_sdr_reg_file { + u32 signature; + u32 debug_data_addr; + u32 cur_stage; + u32 fom; + u32 failing_stage; + u32 debug1; + u32 debug2; + u32 dtaps_per_ptap; + u32 trk_sample_count; + u32 trk_longidle; + u32 delays; + u32 trk_rw_mgr_addr; + u32 trk_read_dqs_width; + u32 trk_rfsh; +}; + +/* parameter variable holder */ +struct param_type { + uint32_t dm_correct_mask; + uint32_t read_correct_mask; + uint32_t read_correct_mask_vg; + uint32_t write_correct_mask; + uint32_t write_correct_mask_vg; + + /* set a particular entry to 1 if we need to skip a particular rank */ + + uint32_t skip_ranks[MAX_RANKS]; + + /* set a particular entry to 1 if we need to skip a particular group */ + + uint32_t skip_groups; + + /* set a particular entry to 1 if the shadow register + (which represents a set of ranks) needs to be skipped */ + + uint32_t skip_shadow_regs[NUM_SHADOW_REGS]; + +}; + + +/* global variable holder */ +struct gbl_type { + uint32_t phy_debug_mode_flags; + + /* current read latency */ + + uint32_t curr_read_lat; + + /* current write latency */ + + uint32_t curr_write_lat; + + /* error code */ + + uint32_t error_substage; + uint32_t error_stage; + uint32_t error_group; + + /* figure-of-merit in, figure-of-merit out */ + + uint32_t fom_in; + uint32_t fom_out; + + /*USER Number of RW Mgr NOP cycles between + write command and write data */ + uint32_t rw_wl_nop_cycles; +}; + +struct socfpga_sdr_scc_mgr { + u32 dqs_ena; + u32 dqs_io_ena; + u32 dq_ena; + u32 dm_ena; + u32 __padding1[4]; + u32 update; + u32 __padding2[7]; + u32 active_rank; +}; + +/* PHY manager configuration registers. */ +struct socfpga_phy_mgr_cfg { + u32 phy_rlat; + u32 reset_mem_stbl; + u32 mux_sel; + u32 cal_status; + u32 cal_debug_info; + u32 vfifo_rd_en_ovrd; + u32 afi_wlat; + u32 afi_rlat; +}; + +/* PHY manager command addresses. */ +struct socfpga_phy_mgr_cmd { + u32 inc_vfifo_fr; + u32 inc_vfifo_hard_phy; + u32 fifo_reset; + u32 inc_vfifo_fr_hr; + u32 inc_vfifo_qr; +}; + +struct socfpga_data_mgr { + u32 __padding1; + u32 t_wl_add; + u32 mem_t_add; + u32 t_rl_add; +}; +#endif /* _SEQUENCER_H_ */ diff --git a/drivers/ddr/altera/sequencer_auto.h b/drivers/ddr/altera/sequencer_auto.h new file mode 100644 index 0000000..0c5d83b --- /dev/null +++ b/drivers/ddr/altera/sequencer_auto.h @@ -0,0 +1,128 @@ +/* + * Copyright Altera Corporation (C) 2012-2015 + * + * SPDX-License-Identifier: BSD-3-Clause + */ + + +#define RW_MGR_READ_B2B_WAIT2 0x6A +#define RW_MGR_LFSR_WR_RD_BANK_0_WAIT 0x31 +#define RW_MGR_REFRESH_ALL 0x14 +#define RW_MGR_ZQCL 0x06 +#define RW_MGR_LFSR_WR_RD_BANK_0_NOP 0x22 +#define RW_MGR_LFSR_WR_RD_BANK_0_DQS 0x23 +#define RW_MGR_ACTIVATE_0_AND_1 0x0D +#define RW_MGR_MRS2_MIRR 0x0A +#define RW_MGR_INIT_RESET_0_CKE_0 0x6E +#define RW_MGR_LFSR_WR_RD_DM_BANK_0_WAIT 0x45 +#define RW_MGR_ACTIVATE_1 0x0F +#define RW_MGR_MRS2 0x04 +#define RW_MGR_LFSR_WR_RD_DM_BANK_0_WL_1 0x34 +#define RW_MGR_MRS1 0x03 +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +#define RW_MGR_IDLE_LOOP1 0x7A +#else +#define RW_MGR_IDLE_LOOP1 0x7C +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +#define RW_MGR_GUARANTEED_WRITE_WAIT2 0x18 +#define RW_MGR_MRS3 0x05 +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +#define RW_MGR_IDLE_LOOP2 0x79 +#else +#define RW_MGR_IDLE_LOOP2 0x7B +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +#define RW_MGR_GUARANTEED_WRITE_WAIT1 0x1E +#define RW_MGR_LFSR_WR_RD_BANK_0_DATA 0x24 +#define RW_MGR_GUARANTEED_WRITE_WAIT3 0x1C +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +#define RW_MGR_RDIMM_CMD 0x78 +#else +#define RW_MGR_RDIMM_CMD 0x7A +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +#define RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP 0x36 +#define RW_MGR_GUARANTEED_WRITE_WAIT0 0x1A +#define RW_MGR_LFSR_WR_RD_DM_BANK_0_DATA 0x38 +#define RW_MGR_GUARANTEED_READ_CONT 0x53 +#define RW_MGR_MRS3_MIRR 0x0B +#define RW_MGR_IDLE 0x00 +#define RW_MGR_READ_B2B 0x58 +#define RW_MGR_INIT_RESET_0_CKE_0_inloop 0x6F +#define RW_MGR_LFSR_WR_RD_DM_BANK_0_DQS 0x37 +#define RW_MGR_GUARANTEED_WRITE 0x17 +#define RW_MGR_PRECHARGE_ALL 0x12 +#define RW_MGR_INIT_RESET_1_CKE_0_inloop_1 0x74 +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +#define RW_MGR_SGLE_READ 0x7C +#else +#define RW_MGR_SGLE_READ 0x7E +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +#define RW_MGR_MRS0_USER_MIRR 0x0C +#define RW_MGR_RETURN 0x01 +#define RW_MGR_LFSR_WR_RD_DM_BANK_0 0x35 +#define RW_MGR_MRS0_USER 0x07 +#define RW_MGR_GUARANTEED_READ 0x4B +#define RW_MGR_MRS0_DLL_RESET_MIRR 0x08 +#define RW_MGR_INIT_RESET_1_CKE_0 0x73 +#define RW_MGR_ACTIVATE_0_AND_1_WAIT2 0x10 +#define RW_MGR_LFSR_WR_RD_BANK_0_WL_1 0x20 +#define RW_MGR_MRS0_DLL_RESET 0x02 +#define RW_MGR_ACTIVATE_0_AND_1_WAIT1 0x0E +#define RW_MGR_LFSR_WR_RD_BANK_0 0x21 +#define RW_MGR_CLEAR_DQS_ENABLE 0x48 +#define RW_MGR_MRS1_MIRR 0x09 +#define RW_MGR_READ_B2B_WAIT1 0x60 +#define RW_MGR_CONTENT_READ_B2B_WAIT2 0x00C680 +#define RW_MGR_CONTENT_LFSR_WR_RD_BANK_0_WAIT 0x00A680 +#define RW_MGR_CONTENT_REFRESH_ALL 0x000980 +#define RW_MGR_CONTENT_ZQCL 0x008380 +#define RW_MGR_CONTENT_LFSR_WR_RD_BANK_0_NOP 0x00E700 +#define RW_MGR_CONTENT_LFSR_WR_RD_BANK_0_DQS 0x000C00 +#define RW_MGR_CONTENT_ACTIVATE_0_AND_1 0x000800 +#define RW_MGR_CONTENT_MRS2_MIRR 0x008580 +#define RW_MGR_CONTENT_INIT_RESET_0_CKE_0 0x000000 +#define RW_MGR_CONTENT_LFSR_WR_RD_DM_BANK_0_WAIT 0x00A680 +#define RW_MGR_CONTENT_ACTIVATE_1 0x000880 +#define RW_MGR_CONTENT_MRS2 0x008280 +#define RW_MGR_CONTENT_LFSR_WR_RD_DM_BANK_0_WL_1 0x00CE00 +#define RW_MGR_CONTENT_MRS1 0x008200 +#define RW_MGR_CONTENT_IDLE_LOOP1 0x00A680 +#define RW_MGR_CONTENT_GUARANTEED_WRITE_WAIT2 0x00CCE8 +#define RW_MGR_CONTENT_MRS3 0x008300 +#define RW_MGR_CONTENT_IDLE_LOOP2 0x008680 +#define RW_MGR_CONTENT_GUARANTEED_WRITE_WAIT1 0x00AC88 +#define RW_MGR_CONTENT_LFSR_WR_RD_BANK_0_DATA 0x020CE0 +#define RW_MGR_CONTENT_GUARANTEED_WRITE_WAIT3 0x00EC88 +#define RW_MGR_CONTENT_RDIMM_CMD 0x009180 +#define RW_MGR_CONTENT_LFSR_WR_RD_DM_BANK_0_NOP 0x00E700 +#define RW_MGR_CONTENT_GUARANTEED_WRITE_WAIT0 0x008CE8 +#define RW_MGR_CONTENT_LFSR_WR_RD_DM_BANK_0_DATA 0x030CE0 +#define RW_MGR_CONTENT_GUARANTEED_READ_CONT 0x001168 +#define RW_MGR_CONTENT_MRS3_MIRR 0x008600 +#define RW_MGR_CONTENT_IDLE 0x080000 +#define RW_MGR_CONTENT_READ_B2B 0x040E88 +#define RW_MGR_CONTENT_INIT_RESET_0_CKE_0_inloop 0x000000 +#define RW_MGR_CONTENT_LFSR_WR_RD_DM_BANK_0_DQS 0x000C00 +#define RW_MGR_CONTENT_GUARANTEED_WRITE 0x000B68 +#define RW_MGR_CONTENT_PRECHARGE_ALL 0x000900 +#define RW_MGR_CONTENT_INIT_RESET_1_CKE_0_inloop_1 0x000080 +#define RW_MGR_CONTENT_SGLE_READ 0x040F08 +#define RW_MGR_CONTENT_MRS0_USER_MIRR 0x008400 +#define RW_MGR_CONTENT_RETURN 0x080680 +#define RW_MGR_CONTENT_LFSR_WR_RD_DM_BANK_0 0x00CD80 +#define RW_MGR_CONTENT_MRS0_USER 0x008100 +#define RW_MGR_CONTENT_GUARANTEED_READ 0x001168 +#define RW_MGR_CONTENT_MRS0_DLL_RESET_MIRR 0x008480 +#define RW_MGR_CONTENT_INIT_RESET_1_CKE_0 0x000080 +#define RW_MGR_CONTENT_ACTIVATE_0_AND_1_WAIT2 0x00A680 +#define RW_MGR_CONTENT_LFSR_WR_RD_BANK_0_WL_1 0x00CE00 +#define RW_MGR_CONTENT_MRS0_DLL_RESET 0x008180 +#define RW_MGR_CONTENT_ACTIVATE_0_AND_1_WAIT1 0x008680 +#define RW_MGR_CONTENT_LFSR_WR_RD_BANK_0 0x00CD80 +#define RW_MGR_CONTENT_CLEAR_DQS_ENABLE 0x001158 +#define RW_MGR_CONTENT_MRS1_MIRR 0x008500 +#define RW_MGR_CONTENT_READ_B2B_WAIT1 0x00A680 + diff --git a/drivers/ddr/altera/sequencer_auto_ac_init.h b/drivers/ddr/altera/sequencer_auto_ac_init.h new file mode 100644 index 0000000..c46421b --- /dev/null +++ b/drivers/ddr/altera/sequencer_auto_ac_init.h @@ -0,0 +1,84 @@ +/* + * Copyright Altera Corporation (C) 2012-2015 + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +const uint32_t ac_rom_init[] = { +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ + 0x20700000, + 0x20780000, + 0x10080831, + 0x10080930, + 0x10090004, + 0x100a0008, + 0x100b0000, + 0x10380400, + 0x10080849, + 0x100808c8, + 0x100a0004, + 0x10090010, + 0x100b0000, + 0x30780000, + 0x38780000, + 0x30780000, + 0x10680000, + 0x106b0000, + 0x10280400, + 0x10480000, + 0x1c980000, + 0x1c9b0000, + 0x1c980008, + 0x1c9b0008, + 0x38f80000, + 0x3cf80000, + 0x38780000, + 0x18180000, + 0x18980000, + 0x13580000, + 0x135b0000, + 0x13580008, + 0x135b0008, + 0x33780000, + 0x10580008, + 0x10780000 +#else + 0x20700000, + 0x20780000, + 0x10080431, + 0x10080530, + 0x10090004, + 0x100a0008, + 0x100b0000, + 0x10380400, + 0x10080449, + 0x100804c8, + 0x100a0004, + 0x10090010, + 0x100b0000, + 0x30780000, + 0x38780000, + 0x30780000, + 0x10680000, + 0x106b0000, + 0x10280400, + 0x10480000, + 0x1c980000, + 0x1c9b0000, + 0x1c980008, + 0x1c9b0008, + 0x38f80000, + 0x3cf80000, + 0x38780000, + 0x18180000, + 0x18980000, + 0x13580000, + 0x135b0000, + 0x13580008, + 0x135b0008, + 0x33780000, + 0x10580008, + 0x10780000 +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +}; diff --git a/drivers/ddr/altera/sequencer_auto_inst_init.h b/drivers/ddr/altera/sequencer_auto_inst_init.h new file mode 100644 index 0000000..ad0395b --- /dev/null +++ b/drivers/ddr/altera/sequencer_auto_inst_init.h @@ -0,0 +1,268 @@ +/* + * Copyright Altera Corporation (C) 2012-2015 + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +const u32 inst_rom_init[] = { + 0x80000, + 0x80680, + 0x8180, + 0x8200, + 0x8280, + 0x8300, + 0x8380, + 0x8100, + 0x8480, + 0x8500, + 0x8580, + 0x8600, + 0x8400, + 0x800, + 0x8680, + 0x880, + 0xa680, + 0x80680, + 0x900, + 0x80680, + 0x980, + 0x8680, + 0x80680, + 0xb68, + 0xcce8, + 0xae8, + 0x8ce8, + 0xb88, + 0xec88, + 0xa08, + 0xac88, + 0x80680, + 0xce00, + 0xcd80, + 0xe700, + 0xc00, + 0x20ce0, + 0x20ce0, + 0x20ce0, + 0x20ce0, + 0xd00, + 0x680, + 0x680, + 0x680, + 0x680, + 0x60e80, + 0x61080, + 0x61080, + 0x61080, + 0xa680, + 0x8680, + 0x80680, + 0xce00, + 0xcd80, + 0xe700, + 0xc00, + 0x30ce0, + 0x30ce0, + 0x30ce0, + 0x30ce0, + 0xd00, + 0x680, + 0x680, + 0x680, + 0x680, + 0x70e80, + 0x71080, + 0x71080, + 0x71080, + 0xa680, + 0x8680, + 0x80680, + 0x1158, + 0x6d8, + 0x80680, + 0x1168, + 0x7e8, + 0x7e8, + 0x87e8, + 0x40fe8, + 0x410e8, + 0x410e8, + 0x410e8, + 0x1168, + 0x7e8, + 0x7e8, + 0xa7e8, + 0x80680, + 0x40e88, + 0x41088, + 0x41088, + 0x41088, + 0x40f68, + 0x410e8, + 0x410e8, + 0x410e8, + 0xa680, + 0x40fe8, + 0x410e8, + 0x410e8, + 0x410e8, + 0x41008, + 0x41088, + 0x41088, + 0x41088, + 0x1100, + 0xc680, + 0x8680, + 0xe680, + 0x80680, + 0x0, + 0x8000, + 0xa000, + 0xc000, + 0x80000, + 0x80, + 0x8080, + 0xa080, + 0xc080, + 0x80080, + 0x9180, + 0x8680, + 0xa680, + 0x80680, + 0x40f08, + 0x80680 +}; +#else +const u32 inst_rom_init[] = { + 0x80000, + 0x80680, + 0x8180, + 0x8200, + 0x8280, + 0x8300, + 0x8380, + 0x8100, + 0x8480, + 0x8500, + 0x8580, + 0x8600, + 0x8400, + 0x800, + 0x8680, + 0x880, + 0xa680, + 0x80680, + 0x900, + 0x80680, + 0x980, + 0x8680, + 0x80680, + 0xb68, + 0xcce8, + 0xae8, + 0x8ce8, + 0xb88, + 0xec88, + 0xa08, + 0xac88, + 0x80680, + 0xce00, + 0xcd80, + 0xe700, + 0xc00, + 0x20ce0, + 0x20ce0, + 0x20ce0, + 0x20ce0, + 0xd00, + 0x680, + 0x680, + 0x680, + 0x680, + 0x60e80, + 0x61080, + 0x61080, + 0x61080, + 0xa680, + 0x8680, + 0x80680, + 0xce00, + 0xcd80, + 0xe700, + 0xc00, + 0x30ce0, + 0x30ce0, + 0x30ce0, + 0x30ce0, + 0xd00, + 0x680, + 0x680, + 0x680, + 0x680, + 0x70e80, + 0x71080, + 0x71080, + 0x71080, + 0xa680, + 0x8680, + 0x80680, + 0x1158, + 0x6d8, + 0x80680, + 0x1168, + 0x7e8, + 0x7e8, + 0x87e8, + 0x40fe8, + 0x410e8, + 0x410e8, + 0x410e8, + 0x1168, + 0x7e8, + 0x7e8, + 0xa7e8, + 0x80680, + 0x40e88, + 0x41088, + 0x41088, + 0x41088, + 0x40f68, + 0x410e8, + 0x410e8, + 0x410e8, + 0xa680, + 0x40fe8, + 0x410e8, + 0x410e8, + 0x410e8, + 0x41008, + 0x41088, + 0x41088, + 0x41088, + 0x1100, + 0xc680, + 0x8680, + 0xe680, + 0x80680, + 0x0, + 0x0, + 0xa000, + 0x8000, + 0x80000, + 0x80, + 0x80, + 0x80, + 0x80, + 0xa080, + 0x8080, + 0x80080, + 0x9180, + 0x8680, + 0xa680, + 0x80680, + 0x40f08, + 0x80680 +}; +#endif /* CONFIG_SOCFPGA_ARRIA5 */ diff --git a/drivers/ddr/altera/sequencer_defines.h b/drivers/ddr/altera/sequencer_defines.h new file mode 100644 index 0000000..32f13ac --- /dev/null +++ b/drivers/ddr/altera/sequencer_defines.h @@ -0,0 +1,121 @@ +/* + * Copyright Altera Corporation (C) 2012-2015 + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#ifndef _SEQUENCER_DEFINES_H_ +#define _SEQUENCER_DEFINES_H_ + +#define AC_ROM_MR1_MIRR 0000000000100 +#define AC_ROM_MR1_OCD_ENABLE +#define AC_ROM_MR2_MIRR 0000000010000 +#define AC_ROM_MR3_MIRR 0000000000000 +#define AC_ROM_MR0_CALIB +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +#define AC_ROM_MR0_DLL_RESET_MIRR 0100011001000 +#define AC_ROM_MR0_DLL_RESET 0100100110000 +#define AC_ROM_MR0_MIRR 0100001001001 +#define AC_ROM_MR0 0100000110001 +#else +#define AC_ROM_MR0_DLL_RESET_MIRR 0010011001000 +#define AC_ROM_MR0_DLL_RESET 0010100110000 +#define AC_ROM_MR0_MIRR 0010001001001 +#define AC_ROM_MR0 0010000110001 +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +#define AC_ROM_MR1 0000000000100 +#define AC_ROM_MR2 0000000001000 +#define AC_ROM_MR3 0000000000000 +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +#define AFI_CLK_FREQ 534 +#else +#define AFI_CLK_FREQ 401 +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +#define AFI_RATE_RATIO 1 +#define AVL_CLK_FREQ 67 +#define BFM_MODE 0 +#define BURST2 0 +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +#define CALIB_LFIFO_OFFSET 8 +#define CALIB_VFIFO_OFFSET 6 +#else +#define CALIB_LFIFO_OFFSET 7 +#define CALIB_VFIFO_OFFSET 5 +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +#define ENABLE_EXPORT_SEQ_DEBUG_BRIDGE 0 +#define ENABLE_SUPER_QUICK_CALIBRATION 0 +#define GUARANTEED_READ_BRINGUP_TEST 0 +#define HARD_PHY 1 +#define HARD_VFIFO 1 +#define HPS_HW 1 +#define HR_DDIO_OUT_HAS_THREE_REGS 0 +#define IO_DELAY_PER_DCHAIN_TAP 25 +#define IO_DELAY_PER_DQS_EN_DCHAIN_TAP 25 +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +#define IO_DELAY_PER_OPA_TAP 234 +#else +#define IO_DELAY_PER_OPA_TAP 312 +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +#define IO_DLL_CHAIN_LENGTH 8 +#define IO_DM_OUT_RESERVE 0 +#define IO_DQDQS_OUT_PHASE_MAX 0 +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +#define IO_DQS_EN_DELAY_MAX 15 +#define IO_DQS_EN_DELAY_OFFSET 16 +#else +#define IO_DQS_EN_DELAY_MAX 31 +#define IO_DQS_EN_DELAY_OFFSET 0 +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +#define IO_DQS_EN_PHASE_MAX 7 +#define IO_DQS_IN_DELAY_MAX 31 +#define IO_DQS_IN_RESERVE 4 +#define IO_DQS_OUT_RESERVE 6 +#define IO_DQ_OUT_RESERVE 0 +#define IO_IO_IN_DELAY_MAX 31 +#define IO_IO_OUT1_DELAY_MAX 31 +#define IO_IO_OUT2_DELAY_MAX 0 +#define IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS 0 +#define MARGIN_VARIATION_TEST 0 +#define MAX_LATENCY_COUNT_WIDTH 5 +#define MEM_ADDR_WIDTH 13 +#define READ_VALID_FIFO_SIZE 16 +#ifdef CONFIG_SOCFPGA_ARRIA5 +/* The if..else... is not required if generated by tools */ +#define REG_FILE_INIT_SEQ_SIGNATURE 0x5555048c +#else +#define REG_FILE_INIT_SEQ_SIGNATURE 0x55550483 +#endif /* CONFIG_SOCFPGA_ARRIA5 */ +#define RW_MGR_MEM_ADDRESS_MIRRORING 0 +#define RW_MGR_MEM_ADDRESS_WIDTH 15 +#define RW_MGR_MEM_BANK_WIDTH 3 +#define RW_MGR_MEM_CHIP_SELECT_WIDTH 1 +#define RW_MGR_MEM_CLK_EN_WIDTH 1 +#define RW_MGR_MEM_CONTROL_WIDTH 1 +#define RW_MGR_MEM_DATA_MASK_WIDTH 5 +#define RW_MGR_MEM_DATA_WIDTH 40 +#define RW_MGR_MEM_DQ_PER_READ_DQS 8 +#define RW_MGR_MEM_DQ_PER_WRITE_DQS 8 +#define RW_MGR_MEM_IF_READ_DQS_WIDTH 5 +#define RW_MGR_MEM_IF_WRITE_DQS_WIDTH 5 +#define RW_MGR_MEM_NUMBER_OF_CS_PER_DIMM 1 +#define RW_MGR_MEM_ODT_WIDTH 1 +#define RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS 1 +#define RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS 1 +#define RW_MGR_MR0_BL 1 +#define RW_MGR_MR0_CAS_LATENCY 3 +#define RW_MGR_TRUE_MEM_DATA_MASK_WIDTH 5 +#define RW_MGR_WRITE_TO_DEBUG_READ 1.0 +#define SKEW_CALIBRATION 0 +#define TINIT_CNTR1_VAL 32 +#define TINIT_CNTR2_VAL 32 +#define TINIT_CNTR0_VAL 132 +#define TRESET_CNTR1_VAL 99 +#define TRESET_CNTR2_VAL 10 +#define TRESET_CNTR0_VAL 132 + +#endif /* _SEQUENCER_DEFINES_H_ */