Whitebox
/
u-boot
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

* Enable NAND flash support for NC650 board.

Browse Source 
* Patch by Thomas Lange 07 Oct 2004:
  Updated README for DBAu1x00 boards to match current status
master
wdenk 21 years ago
parent d407bf52b5
commit 4cfaf55e5c
4 changed files with 80 additions and 21 deletions
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Show Stats Download Patch File Download Diff File
  1. 5
      CHANGELOG
  2. 34
      board/dbau1x00/README
  3. 10
      board/nc650/nc650.c
  4. 52
      include/configs/NC650.h

5
CHANGELOG
Unescape View File

@ -2,6 +2,11 @@
Changes since U-Boot 1.1.1:
======================================================================
* Enable NAND flash support for NC650 board.
* Patch by Thomas Lange 07 Oct 2004:
Updated README for DBAu1x00 boards to match current status
* Patch by Philippe Robin, 28 Sept 2004:
Fix Flash support for Versatile.

34
board/dbau1x00/README
Unescape View File

@ -1,30 +1,40 @@
By Thomas.Lange@corelatus.se 2003-10-06
By Thomas.Lange@corelatus.se 2004-Oct-05
----------------------------------------
DbAu1000 is a development board from AMD containing
an Alchemy AU1000 with mips32 core.
DbAu1xx0 are development boards from AMD containing
an Alchemy AU1xx0 series cpu with mips32 core.
Existing cpu:s are Au1000, Au1100, Au1500 and Au1550
Limitations & comments
----------------------
I assume that you set board to BIG endian!
Little endian not tested, most probably broken.
Support was originally big endian only.
I have not tested, but several u-boot users report working
configurations in little endian mode.
I named the board dbau1x00, to allow
support for all three development boards
some day ( dbau1000, dbau1100 and dbau1500 ).
( dbau1000, dbau1100 and dbau1500 ).
Now there is a new board called dbau1550 also, which
should be supported RSN.
I only have a dbau1000, so all testing is limited
to this board!
I only have a dbau1000, so my testing is limited
to this board.
The board has two different flash banks, that can
be selected via dip switch. This makes it possible
to test new bootloaders without thrashing the YAMON
boot loader deliviered with board.
boot loader delivered with board.
NOTE! When you switch between the two boot flashes, the
base addresses will be swapped.
Have this in mind when you compile u-boot. TEXT_BASE has
to match the address where u-boot is located when you
actually launch.
Ethernet only supported for mac0.
Pcmcia only supported for slot 0, only 3.3V.
PCMCIA only supported for slot 0, only 3.3V.
Pcmcia IDE tested with Sandisk Compact Flash and
PCMCIA IDE tested with Sandisk Compact Flash and
IBM microdrive.
###################################
@ -32,7 +42,7 @@ IBM microdrive.
###################################
If you partition a disk on another system (e.g. laptop),
all bytes will be swapped on 16bit level when using
PCMCIA!!!!
PCMCIA and running cpu in big endian mode!!!!
This is probably due to an error in Au1000 chip.

10
board/nc650/nc650.c
Unescape View File

@ -205,3 +205,13 @@ static long int dram_size (long int mamr_value, long int *base,
return (get_ram_size(base, maxsize));
}
#if (CONFIG_COMMANDS & CFG_CMD_NAND)
void nand_init(void)
{
unsigned long totlen = nand_probe(CFG_NAND_BASE);
printf ("%4lu MB\n", totlen >> 20);
}
#endif

52
include/configs/NC650.h
Unescape View File

@ -96,8 +96,8 @@
/*
* Software (bit-bang) I2C driver configuration
*/
#define SCL 0x10000000 /* PA 3 */
#define SDA 0x40000000 /* PA 1 */
#define SCL 0x1000 /* PA 3 */
#define SDA 0x2000 /* PA 2 */
#define PAR immr->im_ioport.iop_papar
#define DIR immr->im_ioport.iop_padir
@ -111,19 +111,16 @@
else DAT &= ~SDA
#define I2C_SCL(bit) if (bit) DAT |= SCL; \
else DAT &= ~SCL
#define I2C_DELAY udelay(50) /* 1/4 I2C clock duration */
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#define CFG_I2C_EEPROM_ADDR 0x50
#define CFG_I2C_EEPROM_ADDR_LEN 1
#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* 16 bytes page write mode */
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
#define CONFIG_RTC_PCF8563
#define CFG_I2C_RTC_ADDR 0x51
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_ASKENV | \
CFG_CMD_DHCP | \
CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_NAND | \
CFG_CMD_DATE )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
@ -216,6 +213,31 @@
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*
* NAND flash support
*/
#define CFG_MAX_NAND_DEVICE 1
#define NAND_ChipID_UNKNOWN 0x00
#define SECTORSIZE 512
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define ADDR_COLUMN 1
#define NAND_NO_RB
#define NAND_WAIT_READY(nand) udelay(12)
#define WRITE_NAND_COMMAND(d, adr) WRITE_NAND(d, adr + 2)
#define WRITE_NAND_ADDRESS(d, adr) WRITE_NAND(d, adr + 1)
#define WRITE_NAND(d, adr) (*(volatile uint8_t *)(adr) = (uint8_t)(d))
#define READ_NAND(adr) (*(volatile uint8_t *)(adr))
#define NAND_DISABLE_CE(nand) /* nop */
#define NAND_ENABLE_CE(nand) /* nop */
#define NAND_CTL_CLRALE(nandptr) /* nop */
#define NAND_CTL_SETALE(nandptr) /* nop */
#define NAND_CTL_CLRCLE(nandptr) /* nop */
#define NAND_CTL_SETCLE(nandptr) /* nop */
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
@ -287,6 +309,18 @@
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V)
/*
* BR2 and OR2 (NAND Flash)
*/
#define CFG_NAND_BASE 0x50000000
#define CFG_NAND_SIZE 0x04000000
#define CFG_OR_TIMING_NAND (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
OR_SCY_15_CLK | OR_EHTR | OR_TRLX)
#define CFG_BR2_PRELIM ((CFG_NAND_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
#define CFG_OR2_PRELIM (((-CFG_NAND_SIZE) & OR_AM_MSK) | CFG_OR_TIMING_NAND)
/*
* BR3 and OR3 (SDRAM)
*/
#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */

Write Preview
Loading…
Cancel
Save