From 5344cc1a82fcc2817d4671696b3939b0dfa4323e Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Fri, 23 Jan 2015 00:24:19 +0900 Subject: [PATCH] powerpc: ppc4xx: remove PPChameleonEVB, CATcenter boards These boards are still non-generic boards. It is a good thing that we can drop board-specific hack code from drivers/mtd/nand/nand_base.c Signed-off-by: Masahiro Yamada Acked-by: Stefan Roese Cc: Andrea "llandre" Marson --- arch/powerpc/cpu/ppc4xx/Kconfig | 7 - board/dave/PPChameleonEVB/Kconfig | 25 - board/dave/PPChameleonEVB/MAINTAINERS | 20 - board/dave/PPChameleonEVB/Makefile | 8 - board/dave/PPChameleonEVB/PPChameleonEVB.c | 231 --------- board/dave/PPChameleonEVB/flash.c | 99 ---- board/dave/PPChameleonEVB/nand.c | 99 ---- board/dave/PPChameleonEVB/u-boot.lds | 115 ----- configs/CATcenter_25_defconfig | 4 - configs/CATcenter_33_defconfig | 4 - configs/CATcenter_defconfig | 4 - configs/PPChameleonEVB_BA_25_defconfig | 4 - configs/PPChameleonEVB_BA_33_defconfig | 4 - configs/PPChameleonEVB_HI_25_defconfig | 4 - configs/PPChameleonEVB_HI_33_defconfig | 4 - configs/PPChameleonEVB_ME_25_defconfig | 4 - configs/PPChameleonEVB_ME_33_defconfig | 4 - configs/PPChameleonEVB_defconfig | 3 - doc/README.scrapyard | 2 + drivers/mtd/nand/nand_base.c | 5 - include/configs/CATcenter.h | 750 ---------------------------- include/configs/PPChameleonEVB.h | 777 ----------------------------- 22 files changed, 2 insertions(+), 2175 deletions(-) delete mode 100644 board/dave/PPChameleonEVB/Kconfig delete mode 100644 board/dave/PPChameleonEVB/MAINTAINERS delete mode 100644 board/dave/PPChameleonEVB/Makefile delete mode 100644 board/dave/PPChameleonEVB/PPChameleonEVB.c delete mode 100644 board/dave/PPChameleonEVB/flash.c delete mode 100644 board/dave/PPChameleonEVB/nand.c delete mode 100644 board/dave/PPChameleonEVB/u-boot.lds delete mode 100644 configs/CATcenter_25_defconfig delete mode 100644 configs/CATcenter_33_defconfig delete mode 100644 configs/CATcenter_defconfig delete mode 100644 configs/PPChameleonEVB_BA_25_defconfig delete mode 100644 configs/PPChameleonEVB_BA_33_defconfig delete mode 100644 configs/PPChameleonEVB_HI_25_defconfig delete mode 100644 configs/PPChameleonEVB_HI_33_defconfig delete mode 100644 configs/PPChameleonEVB_ME_25_defconfig delete mode 100644 configs/PPChameleonEVB_ME_33_defconfig delete mode 100644 configs/PPChameleonEVB_defconfig delete mode 100644 include/configs/CATcenter.h delete mode 100644 include/configs/PPChameleonEVB.h diff --git a/arch/powerpc/cpu/ppc4xx/Kconfig b/arch/powerpc/cpu/ppc4xx/Kconfig index a40ae3b..5db5e34 100644 --- a/arch/powerpc/cpu/ppc4xx/Kconfig +++ b/arch/powerpc/cpu/ppc4xx/Kconfig @@ -101,12 +101,6 @@ config TARGET_FX12MM config TARGET_V5FX30TEVAL bool "Support v5fx30teval" -config TARGET_CATCENTER - bool "Support CATcenter" - -config TARGET_PPCHAMELEONEVB - bool "Support PPChameleonEVB" - config TARGET_CPCI2DP bool "Support CPCI2DP" @@ -199,7 +193,6 @@ source "board/avnet/fx12mm/Kconfig" source "board/avnet/v5fx30teval/Kconfig" source "board/csb272/Kconfig" source "board/csb472/Kconfig" -source "board/dave/PPChameleonEVB/Kconfig" source "board/esd/cpci2dp/Kconfig" source "board/esd/cpci405/Kconfig" source "board/esd/plu405/Kconfig" diff --git a/board/dave/PPChameleonEVB/Kconfig b/board/dave/PPChameleonEVB/Kconfig deleted file mode 100644 index bfe0011..0000000 --- a/board/dave/PPChameleonEVB/Kconfig +++ /dev/null @@ -1,25 +0,0 @@ -if TARGET_CATCENTER - -config SYS_BOARD - default "PPChameleonEVB" - -config SYS_VENDOR - default "dave" - -config SYS_CONFIG_NAME - default "CATcenter" - -endif - -if TARGET_PPCHAMELEONEVB - -config SYS_BOARD - default "PPChameleonEVB" - -config SYS_VENDOR - default "dave" - -config SYS_CONFIG_NAME - default "PPChameleonEVB" - -endif diff --git a/board/dave/PPChameleonEVB/MAINTAINERS b/board/dave/PPChameleonEVB/MAINTAINERS deleted file mode 100644 index d43c6d0..0000000 --- a/board/dave/PPChameleonEVB/MAINTAINERS +++ /dev/null @@ -1,20 +0,0 @@ -PPCHAMELEONEVB BOARD -#M: - -S: Maintained -F: board/dave/PPChameleonEVB/ -F: include/configs/CATcenter.h -F: configs/CATcenter_defconfig -F: configs/CATcenter_25_defconfig -F: configs/CATcenter_33_defconfig - -PPCHAMELEONEVB BOARD -M: Andrea "llandre" Marson -S: Maintained -F: include/configs/PPChameleonEVB.h -F: configs/PPChameleonEVB_defconfig -F: configs/PPChameleonEVB_BA_25_defconfig -F: configs/PPChameleonEVB_BA_33_defconfig -F: configs/PPChameleonEVB_HI_25_defconfig -F: configs/PPChameleonEVB_HI_33_defconfig -F: configs/PPChameleonEVB_ME_25_defconfig -F: configs/PPChameleonEVB_ME_33_defconfig diff --git a/board/dave/PPChameleonEVB/Makefile b/board/dave/PPChameleonEVB/Makefile deleted file mode 100644 index 31edc4a..0000000 --- a/board/dave/PPChameleonEVB/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = PPChameleonEVB.o flash.o nand.o diff --git a/board/dave/PPChameleonEVB/PPChameleonEVB.c b/board/dave/PPChameleonEVB/PPChameleonEVB.c deleted file mode 100644 index c9ab50e..0000000 --- a/board/dave/PPChameleonEVB/PPChameleonEVB.c +++ /dev/null @@ -1,231 +0,0 @@ -/* - * (C) Copyright 2003 - * DAVE Srl - * http://www.dave-tech.it - * http://www.wawnet.biz - * mailto:info@wawnet.biz - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -/* ------------------------------------------------------------------------- */ - -int board_early_init_f (void) -{ - out32(GPIO0_OR, CONFIG_SYS_NAND0_CE); /* set initial outputs */ - out32(GPIO0_OR, CONFIG_SYS_NAND1_CE); /* set initial outputs */ - - /* - * IRQ 0-15 405GP internally generated; active high; level sensitive - * IRQ 16 405GP internally generated; active low; level sensitive - * IRQ 17-24 RESERVED - * IRQ 25 (EXT IRQ 0) - * IRQ 26 (EXT IRQ 1) - * IRQ 27 (EXT IRQ 2) - * IRQ 28 (EXT IRQ 3) - * IRQ 29 (EXT IRQ 4) - * IRQ 30 (EXT IRQ 5) - * IRQ 31 (EXT IRQ 6) - */ - mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */ - mtdcr(UIC0ER, 0x00000000); /* disable all ints */ - mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical*/ - mtdcr(UIC0PR, 0xFFFFFF80); /* set int polarities */ - mtdcr(UIC0TR, 0x10000000); /* set int trigger levels */ - mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority*/ - mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */ - - /* - * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us - */ -#if 1 /* test-only */ - mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */ -#else - mtebc (EBC0_CFG, 0x28400000); /* ebc in high-z */ -#endif - return 0; -} - -/* ------------------------------------------------------------------------- */ - -int misc_init_f (void) -{ - return 0; /* dummy implementation */ -} - -extern flash_info_t flash_info[]; /* info for FLASH chips */ - -int misc_init_r (void) -{ - /* adjust flash start and size as well as the offset */ - gd->bd->bi_flashstart = 0 - flash_info[0].size; - gd->bd->bi_flashoffset= flash_info[0].size - CONFIG_SYS_MONITOR_LEN; -#if 0 - volatile unsigned short *fpga_mode = - (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL); - volatile unsigned char *duart0_mcr = - (unsigned char *)((ulong)DUART0_BA + 4); - volatile unsigned char *duart1_mcr = - (unsigned char *)((ulong)DUART1_BA + 4); - - bd_t *bd = gd->bd; - char * tmp; /* Temporary char pointer */ - unsigned char *dst; - ulong len = sizeof(fpgadata); - int status; - int index; - int i; - unsigned long CPC0_CR0Reg; - - dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE); - if (gunzip (dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) { - printf ("GUNZIP ERROR - must RESET board to recover\n"); - do_reset (NULL, 0, 0, NULL); - } - - status = fpga_boot(dst, len); - if (status != 0) { - printf("\nFPGA: Booting failed "); - switch (status) { - case ERROR_FPGA_PRG_INIT_LOW: - printf("(Timeout: INIT not low after asserting PROGRAM*)\n "); - break; - case ERROR_FPGA_PRG_INIT_HIGH: - printf("(Timeout: INIT not high after deasserting PROGRAM*)\n "); - break; - case ERROR_FPGA_PRG_DONE: - printf("(Timeout: DONE not high after programming FPGA)\n "); - break; - } - - /* display infos on fpgaimage */ - index = 15; - for (i=0; i<4; i++) { - len = dst[index]; - printf("FPGA: %s\n", &(dst[index+1])); - index += len+3; - } - putc ('\n'); - /* delayed reboot */ - for (i=20; i>0; i--) { - printf("Rebooting in %2d seconds \r",i); - for (index=0;index<1000;index++) - udelay(1000); - } - putc ('\n'); - do_reset(NULL, 0, 0, NULL); - } - - puts("FPGA: "); - - /* display infos on fpgaimage */ - index = 15; - for (i=0; i<4; i++) { - len = dst[index]; - printf("%s ", &(dst[index+1])); - index += len+3; - } - putc ('\n'); - - free(dst); - - /* - * Reset FPGA via FPGA_DATA pin - */ - SET_FPGA(FPGA_PRG | FPGA_CLK); - udelay(1000); /* wait 1ms */ - SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA); - udelay(1000); /* wait 1ms */ -#endif - -#if 0 - /* - * Enable power on PS/2 interface - */ - *fpga_mode |= CONFIG_SYS_FPGA_CTRL_PS2_RESET; - - /* - * Enable interrupts in exar duart mcr[3] - */ - *duart0_mcr = 0x08; - *duart1_mcr = 0x08; -#endif - return (0); -} - -/* - * Check Board Identity: - */ - -int checkboard (void) -{ - char str[64]; - int i = getenv_f("serial#", str, sizeof(str)); - - puts ("Board: "); - - if (i == -1) { - puts ("### No HW ID - assuming PPChameleonEVB"); - } else { - puts(str); - } - - putc ('\n'); - - return 0; -} - -/* ------------------------------------------------------------------------- */ - -int testdram (void) -{ - /* TODO: XXX XXX XXX */ - printf ("test: 16 MB - ok\n"); - - return (0); -} - -/* ------------------------------------------------------------------------- */ - -#ifdef CONFIG_CFB_CONSOLE -# ifdef CONFIG_CONSOLE_EXTRA_INFO -# include -extern GraphicDevice smi; - -void video_get_info_str (int line_number, char *info) -{ - uint pvr = get_pvr (); - - /* init video info strings for graphic console */ - switch (line_number) { - case 1: - switch (pvr) { - case PVR_405EP_RB: - sprintf (info, " AMCC PowerPC 405EP Rev. B"); - break; - default: - sprintf (info, " AMCC PowerPC 405EP Rev. "); - break; - } - return; - case 2: - sprintf (info, " DAVE Srl PPChameleonEVB - www.dave-tech.it"); - return; - case 3: - sprintf (info, " %s", smi.modeIdent); - return; - } - - /* no more info lines */ - *info = 0; - return; -} -# endif /* CONFIG_CONSOLE_EXTRA_INFO */ -#endif /* CONFIG_CFB_CONSOLE */ diff --git a/board/dave/PPChameleonEVB/flash.c b/board/dave/PPChameleonEVB/flash.c deleted file mode 100644 index 771151b..0000000 --- a/board/dave/PPChameleonEVB/flash.c +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2001 - * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include - -/* - * include common flash code (for esd boards) - */ -#include "../common/flash.c" - -/*----------------------------------------------------------------------- - * Functions - */ -static ulong flash_get_size (vu_long * addr, flash_info_t * info); -static void flash_get_offsets (ulong base, flash_info_t * info); - -/*----------------------------------------------------------------------- - */ - -unsigned long flash_init (void) -{ -#ifdef __DEBUG_START_FROM_SRAM__ - return CONFIG_SYS_DUMMY_FLASH_SIZE; -#else - unsigned long size; - int i; - uint pbcr; - unsigned long base; - int size_val = 0; - - debug("[%s, %d] Entering ...\n", __FUNCTION__, __LINE__); - debug("[%s, %d] flash_info = 0x%p ...\n", __func__, __LINE__, - flash_info); - - /* Init: no FLASHes known */ - for (i=0; i -#include - -#if defined(CONFIG_CMD_NAND) - -#include - -/* - * hardware specific access to control-lines - * function borrowed from Linux 2.6 (drivers/mtd/nand/ppchameleonevb.c) - */ -static void ppchameleonevb_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl) -{ - struct nand_chip *this = mtd->priv; - ulong base = (ulong) this->IO_ADDR_W; - - if (ctrl & NAND_CTRL_CHANGE) { - if ( ctrl & NAND_CLE ) - MACRO_NAND_CTL_SETCLE((unsigned long)base); - else - MACRO_NAND_CTL_CLRCLE((unsigned long)base); - if ( ctrl & NAND_ALE ) - MACRO_NAND_CTL_CLRCLE((unsigned long)base); - else - MACRO_NAND_CTL_CLRALE((unsigned long)base); - if ( ctrl & NAND_NCE ) - MACRO_NAND_ENABLE_CE((unsigned long)base); - else - MACRO_NAND_DISABLE_CE((unsigned long)base); - } - - if (cmd != NAND_CMD_NONE) - writeb(cmd, this->IO_ADDR_W); -} - - -/* - * read device ready pin - * function +/- borrowed from Linux 2.6 (drivers/mtd/nand/ppchameleonevb.c) - */ -static int ppchameleonevb_device_ready(struct mtd_info *mtdinfo) -{ - struct nand_chip *this = mtdinfo->priv; - ulong rb_gpio_pin; - - /* use the base addr to find out which chip are we dealing with */ - switch((ulong) this->IO_ADDR_W) { - case CONFIG_SYS_NAND0_BASE: - rb_gpio_pin = CONFIG_SYS_NAND0_RDY; - break; - case CONFIG_SYS_NAND1_BASE: - rb_gpio_pin = CONFIG_SYS_NAND1_RDY; - break; - default: /* this should never happen */ - return 0; - break; - } - - if (in32(GPIO0_IR) & rb_gpio_pin) - return 1; - return 0; -} - - -/* - * Board-specific NAND initialization. The following members of the - * argument are board-specific (per include/linux/mtd/nand.h): - * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device - * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device - * - cmd_ctrl: hardwarespecific function for accesing control-lines - * - dev_ready: hardwarespecific function for accesing device ready/busy line - * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must - * only be provided if a hardware ECC is available - * - ecc.mode: mode of ecc, see defines - * - chip_delay: chip dependent delay for transfering data from array to - * read regs (tR) - * - options: various chip options. They can partly be set to inform - * nand_scan about special functionality. See the defines for further - * explanation - * Members with a "?" were not set in the merged testing-NAND branch, - * so they are not set here either. - */ -int board_nand_init(struct nand_chip *nand) -{ - - nand->cmd_ctrl = ppchameleonevb_hwcontrol; - nand->dev_ready = ppchameleonevb_device_ready; - nand->ecc.mode = NAND_ECC_SOFT; - nand->chip_delay = NAND_BIG_DELAY_US; - nand->options = NAND_SAMSUNG_LP_OPTIONS; - return 0; -} -#endif diff --git a/board/dave/PPChameleonEVB/u-boot.lds b/board/dave/PPChameleonEVB/u-boot.lds deleted file mode 100644 index 94b7076..0000000 --- a/board/dave/PPChameleonEVB/u-boot.lds +++ /dev/null @@ -1,115 +0,0 @@ -/* - * Copyright 2007-2009 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include "config.h" - -#ifndef RESET_VECTOR_ADDRESS -#define RESET_VECTOR_ADDRESS 0xfffffffc -#endif - -OUTPUT_ARCH(powerpc) - -PHDRS -{ - text PT_LOAD; - bss PT_LOAD; -} - -SECTIONS -{ - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .text : - { - *(.text*) - } :text - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } :text - - /* Read-write section, merged into data segment: */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - _GOT2_TABLE_ = .; - KEEP(*(.got2)) - KEEP(*(.got)) - PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4); - _FIXUP_TABLE_ = .; - KEEP(*(.fixup)) - } - __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; - __fixup_entries = (. - _FIXUP_TABLE_) >> 2; - - .data : - { - *(.data*) - *(.sdata*) - } - _edata = .; - PROVIDE (edata = .); - - . = .; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CONFIG_SYS_MONITOR_BASE, CONFIG_SYS_MONITOR_LEN and CONFIG_SYS_TEXT_BASE may need to be modified."); - . = 0xFFFF8000; - .ppcenv : - { - common/env_embedded.o(.ppcenv); - } - - .resetvec RESET_VECTOR_ADDRESS : - { - KEEP(*(.resetvec)) - } :text = 0xffff - - . = RESET_VECTOR_ADDRESS + 0x4; - - /* - * Make sure that the bss segment isn't linked at 0x0, otherwise its - * address won't be updated during relocation fixups. Note that - * this is a temporary fix. Code to dynamically the fixup the bss - * location will be added in the future. When the bss relocation - * fixup code is present this workaround should be removed. - */ -#if (RESET_VECTOR_ADDRESS == 0xfffffffc) - . |= 0x10; -#endif - - __bss_start = .; - .bss (NOLOAD) : - { - *(.bss*) - *(.sbss*) - *(COMMON) - } :bss - - . = ALIGN(4); - __bss_end = . ; - PROVIDE (end = .); -} diff --git a/configs/CATcenter_25_defconfig b/configs/CATcenter_25_defconfig deleted file mode 100644 index 1a8903c..0000000 --- a/configs/CATcenter_25_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=1,PPCHAMELEON_CLK_25" -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_CATCENTER=y diff --git a/configs/CATcenter_33_defconfig b/configs/CATcenter_33_defconfig deleted file mode 100644 index 4b0eb8d..0000000 --- a/configs/CATcenter_33_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=1,PPCHAMELEON_CLK_33" -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_CATCENTER=y diff --git a/configs/CATcenter_defconfig b/configs/CATcenter_defconfig deleted file mode 100644 index 53e00ad..0000000 --- a/configs/CATcenter_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=1" -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_CATCENTER=y diff --git a/configs/PPChameleonEVB_BA_25_defconfig b/configs/PPChameleonEVB_BA_25_defconfig deleted file mode 100644 index e367299..0000000 --- a/configs/PPChameleonEVB_BA_25_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=0,PPCHAMELEON_CLK_25" -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_PPCHAMELEONEVB=y diff --git a/configs/PPChameleonEVB_BA_33_defconfig b/configs/PPChameleonEVB_BA_33_defconfig deleted file mode 100644 index f4041c9..0000000 --- a/configs/PPChameleonEVB_BA_33_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=0,PPCHAMELEON_CLK_33" -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_PPCHAMELEONEVB=y diff --git a/configs/PPChameleonEVB_HI_25_defconfig b/configs/PPChameleonEVB_HI_25_defconfig deleted file mode 100644 index a9de221..0000000 --- a/configs/PPChameleonEVB_HI_25_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=2,PPCHAMELEON_CLK_25" -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_PPCHAMELEONEVB=y diff --git a/configs/PPChameleonEVB_HI_33_defconfig b/configs/PPChameleonEVB_HI_33_defconfig deleted file mode 100644 index 882262b..0000000 --- a/configs/PPChameleonEVB_HI_33_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=2,PPCHAMELEON_CLK_33" -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_PPCHAMELEONEVB=y diff --git a/configs/PPChameleonEVB_ME_25_defconfig b/configs/PPChameleonEVB_ME_25_defconfig deleted file mode 100644 index f9a0440..0000000 --- a/configs/PPChameleonEVB_ME_25_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=1,PPCHAMELEON_CLK_25" -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_PPCHAMELEONEVB=y diff --git a/configs/PPChameleonEVB_ME_33_defconfig b/configs/PPChameleonEVB_ME_33_defconfig deleted file mode 100644 index 8ee09b8..0000000 --- a/configs/PPChameleonEVB_ME_33_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=1,PPCHAMELEON_CLK_33" -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_PPCHAMELEONEVB=y diff --git a/configs/PPChameleonEVB_defconfig b/configs/PPChameleonEVB_defconfig deleted file mode 100644 index 2d83330..0000000 --- a/configs/PPChameleonEVB_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_PPC=y -CONFIG_4xx=y -CONFIG_TARGET_PPCHAMELEONEVB=y diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 719b970..976fca1 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,6 +12,8 @@ The list should be sorted in reverse chronological order. Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +CATcenter powerpc ppc4xx - - +PPChameleonEVB powerpc ppc4xx - - Andrea "llandre" Marson P2020DS powerpc mpc85xx - - P2020COME powerpc mpc85xx - - Ira W. Snyder P2020RDB powerpc mpc85xx - - Poonam Aggrwal diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 63bdf65..6db6566 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -1065,11 +1065,6 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip) } } #endif -#ifdef PPCHAMELON_NAND_TIMER_HACK - time_start = get_timer(0); - while (get_timer(time_start) < 10) - ; -#endif /* PPCHAMELON_NAND_TIMER_HACK */ led_trigger_event(nand_led_trigger, LED_OFF); status = (int)chip->read_byte(mtd); diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h deleted file mode 100644 index 27539d2..0000000 --- a/include/configs/CATcenter.h +++ /dev/null @@ -1,750 +0,0 @@ -/* - * ueberarbeitet durch Christoph Seyfert - * - * (C) Copyright 2004-2005 DENX Software Engineering, - * Wolfgang Grandegger - * (C) Copyright 2003 - * DAVE Srl - * - * http://www.dave-tech.it - * http://www.wawnet.biz - * mailto:info@wawnet.biz - * - * Credits: Stefan Roese, Wolfgang Denk - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_PPCHAMELEON_MODULE_BA 0 /* Basic Model */ -#define CONFIG_PPCHAMELEON_MODULE_ME 1 /* Medium Model */ -#define CONFIG_PPCHAMELEON_MODULE_HI 2 /* High-End Model */ -#ifndef CONFIG_PPCHAMELEON_MODULE_MODEL -#define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA -#endif - -/* Only one of the following two symbols must be defined (default is 25 MHz) - * CONFIG_PPCHAMELEON_CLK_25 - * CONFIG_PPCHAMELEON_CLK_33 - */ -#if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33)) -#define CONFIG_PPCHAMELEON_CLK_25 -#endif - -#if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33)) -#error "* Two external frequencies (SysClk) are defined! *" -#endif - -#undef CONFIG_PPCHAMELEON_SMI712 - -/* - * Debug stuff - */ -#undef __DEBUG_START_FROM_SRAM__ -#define __DISABLE_MACHINE_EXCEPTION__ - -#ifdef __DEBUG_START_FROM_SRAM__ -#define CONFIG_SYS_DUMMY_FLASH_SIZE 1024*1024*4 -#endif - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405EP 1 /* This is a PPC405 CPU */ -#define CONFIG_PPCHAMELEONEVB 1 /* ...on a PPChameleonEVB board */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFB0000 /* Reserve 320 kB for Monitor */ -#define CONFIG_SYS_LDSCRIPT "board/dave/PPChameleonEVB/u-boot.lds" - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ - -#ifdef CONFIG_PPCHAMELEON_CLK_25 -# define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ -#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ -#else -# error "* External frequency (SysClk) not defined! *" -#endif - -#define CONFIG_CONS_INDEX 2 /* Use UART1 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_VERSION_VARIABLE 1 /* add version variable */ -#define CONFIG_IDENT_STRING "1" - -#undef CONFIG_BOOTARGS - -/* Ethernet stuff */ -#define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */ -#define CONFIG_ETHADDR 00:50:C2:1E:AF:FE -#define CONFIG_HAS_ETH1 -#define CONFIG_ETH1ADDR 00:50:C2:1E:AF:FD - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -#define CONFIG_PPC4xx_EMAC -#undef CONFIG_EXT_PHY - -#define CONFIG_MII 1 /* MII PHY management */ -#ifndef CONFIG_EXT_PHY -#define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */ -#define CONFIG_PHY1_ADDR 16 /* EMAC1 PHY address */ -#else -#define CONFIG_PHY_ADDR 2 /* PHY address */ -#endif -#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NAND -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP - - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ -#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ - -#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ - -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ -#define CONFIG_SYS_BASE_BAUD 691200 - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ - 57600, 115200, 230400, 460800, 921600 } - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ - -/*----------------------------------------------------------------------- - * NAND-FLASH stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_NAND0_BASE 0xFF400000 -#define CONFIG_SYS_NAND1_BASE 0xFF000000 -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE } -#define NAND_BIG_DELAY_US 25 - -/* For CATcenter there is only NAND on the module */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define NAND_NO_RB - -#define CONFIG_SYS_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CONFIG_SYS_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ - -#define CONFIG_SYS_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */ -#define CONFIG_SYS_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */ -#define CONFIG_SYS_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */ -#define CONFIG_SYS_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */ - - -#define MACRO_NAND_DISABLE_CE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_ENABLE_CE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_CLRALE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_ALE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_ALE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_SETALE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_ALE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_ALE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_CLRCLE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CLE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CLE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_SETCLE(nandptr) do { \ - switch((unsigned long)nandptr) { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CLE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CLE); \ - break; \ - } \ -} while(0) - -#ifdef NAND_NO_RB -/* constant delay (see also tR in the datasheet) */ -#define NAND_WAIT_READY(nand) do { \ - udelay(12); \ -} while (0) -#else -/* use the R/B pin */ -/* TBD */ -#endif - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#if 0 /* No PCI on CATcenter */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#undef CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */ -#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ - -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ -#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ -#endif /* No PCI */ - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ -#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ -#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ -/* - * The following defines are added for buggy IOP480 byte interface. - * All other boards should use the standard values (CPCI405 etc.) - */ -#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ -#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ -#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -/*----------------------------------------------------------------------- - * Environment Variable setup - */ -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CONFIG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */ -#define CONFIG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/ -#define CONFIG_ENV_ADDR_REDUND 0xFFFFA000 -#define CONFIG_ENV_SIZE_REDUND 0x2000 - -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ - -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ -#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */ - -/*----------------------------------------------------------------------- - * I2C EEPROM (CAT24WC16) for environment - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ - /* 16 byte page write mode using*/ - /* last 4 bits of the address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */ - -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - */ - -/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x92015480 -#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ - -/* Memory Bank 1 (External SRAM) initialization */ -/* Since this must replace NOR Flash, we use the same settings for CS0 */ -#define CONFIG_SYS_EBC_PB1AP 0x92015480 -#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */ - -/* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x92015480 -#define CONFIG_SYS_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */ - -/* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x92015480 -#define CONFIG_SYS_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */ - -#ifdef CONFIG_PPCHAMELEON_SMI712 -/* - * Video console (graphic: SMI LynxEM) - */ -#define CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_SMI_LYNXEM -#define CONFIG_VIDEO_LOGO -/*#define CONFIG_VIDEO_BMP_LOGO*/ -#define CONFIG_CONSOLE_EXTRA_INFO -#define CONFIG_VGA_AS_SINGLE_DEVICE -/* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */ -#define CONFIG_SYS_ISA_IO 0xE8000000 -/* see also drivers/video/videomodes.c */ -#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x303 -#endif - -/*----------------------------------------------------------------------- - * FPGA stuff - */ -/* FPGA internal regs */ -#define CONFIG_SYS_FPGA_MODE 0x00 -#define CONFIG_SYS_FPGA_STATUS 0x02 -#define CONFIG_SYS_FPGA_TS 0x04 -#define CONFIG_SYS_FPGA_TS_LOW 0x06 -#define CONFIG_SYS_FPGA_TS_CAP0 0x10 -#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12 -#define CONFIG_SYS_FPGA_TS_CAP1 0x14 -#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16 -#define CONFIG_SYS_FPGA_TS_CAP2 0x18 -#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a -#define CONFIG_SYS_FPGA_TS_CAP3 0x1c -#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e - -/* FPGA Mode Reg */ -#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001 -#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100 -#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000 -#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000 - -/* FPGA Status Reg */ -#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001 -#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002 -#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004 -#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008 -#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000 - -#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ -#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ - -/* FPGA program pin configuration */ -#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ -#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ -#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ -#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ -#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in data cache) - */ -/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - -/* On Chip Memory location */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Definitions for GPIO setup (PPC405EP specific) - * - * GPIO0[0] - External Bus Controller BLAST output - * GPIO0[1-9] - Instruction trace outputs -> GPIO - * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs - * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO - * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs - * GPIO0[24-27] - UART0 control signal inputs/outputs - * GPIO0[28-29] - UART1 data signal input/output - * GPIO0[30] - EMAC0 input - * GPIO0[31] - EMAC1 reject packet as output - */ -#define CONFIG_SYS_GPIO0_OSRL 0x40000550 -#define CONFIG_SYS_GPIO0_OSRH 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 -/*#define CONFIG_SYS_GPIO0_ISR1H 0x15555445*/ -#define CONFIG_SYS_GPIO0_ISR1H 0x15555444 -#define CONFIG_SYS_GPIO0_TSRL 0x00000000 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 -#define CONFIG_SYS_GPIO0_TCR 0xF7FF8014 - -#define CONFIG_NO_SERIAL_EEPROM - -/*--------------------------------------------------------------------*/ - -#ifdef CONFIG_NO_SERIAL_EEPROM - -/* -!----------------------------------------------------------------------- -! Defines for entry options. -! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that -! are plugged in the board will be utilized as non-ECC DIMMs. -!----------------------------------------------------------------------- -*/ -#undef AUTO_MEMORY_CONFIG -#define DIMM_READ_ADDR 0xAB -#define DIMM_WRITE_ADDR 0xAA - -/* Defines for CPC0_PLLMR1 Register fields */ -#define PLL_ACTIVE 0x80000000 -#define CPC0_PLLMR1_SSCS 0x80000000 -#define PLL_RESET 0x40000000 -#define CPC0_PLLMR1_PLLR 0x40000000 - /* Feedback multiplier */ -#define PLL_FBKDIV 0x00F00000 -#define CPC0_PLLMR1_FBDV 0x00F00000 -#define PLL_FBKDIV_16 0x00000000 -#define PLL_FBKDIV_1 0x00100000 -#define PLL_FBKDIV_2 0x00200000 -#define PLL_FBKDIV_3 0x00300000 -#define PLL_FBKDIV_4 0x00400000 -#define PLL_FBKDIV_5 0x00500000 -#define PLL_FBKDIV_6 0x00600000 -#define PLL_FBKDIV_7 0x00700000 -#define PLL_FBKDIV_8 0x00800000 -#define PLL_FBKDIV_9 0x00900000 -#define PLL_FBKDIV_10 0x00A00000 -#define PLL_FBKDIV_11 0x00B00000 -#define PLL_FBKDIV_12 0x00C00000 -#define PLL_FBKDIV_13 0x00D00000 -#define PLL_FBKDIV_14 0x00E00000 -#define PLL_FBKDIV_15 0x00F00000 - /* Forward A divisor */ -#define PLL_FWDDIVA 0x00070000 -#define CPC0_PLLMR1_FWDVA 0x00070000 -#define PLL_FWDDIVA_8 0x00000000 -#define PLL_FWDDIVA_7 0x00010000 -#define PLL_FWDDIVA_6 0x00020000 -#define PLL_FWDDIVA_5 0x00030000 -#define PLL_FWDDIVA_4 0x00040000 -#define PLL_FWDDIVA_3 0x00050000 -#define PLL_FWDDIVA_2 0x00060000 -#define PLL_FWDDIVA_1 0x00070000 - /* Forward B divisor */ -#define PLL_FWDDIVB 0x00007000 -#define CPC0_PLLMR1_FWDVB 0x00007000 -#define PLL_FWDDIVB_8 0x00000000 -#define PLL_FWDDIVB_7 0x00001000 -#define PLL_FWDDIVB_6 0x00002000 -#define PLL_FWDDIVB_5 0x00003000 -#define PLL_FWDDIVB_4 0x00004000 -#define PLL_FWDDIVB_3 0x00005000 -#define PLL_FWDDIVB_2 0x00006000 -#define PLL_FWDDIVB_1 0x00007000 - /* PLL tune bits */ -#define PLL_TUNE_MASK 0x000003FF -#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */ -#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */ -#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */ -#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */ -#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */ -#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */ -#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */ - -/* Defines for CPC0_PLLMR0 Register fields */ - /* CPU divisor */ -#define PLL_CPUDIV 0x00300000 -#define CPC0_PLLMR0_CCDV 0x00300000 -#define PLL_CPUDIV_1 0x00000000 -#define PLL_CPUDIV_2 0x00100000 -#define PLL_CPUDIV_3 0x00200000 -#define PLL_CPUDIV_4 0x00300000 - /* PLB divisor */ -#define PLL_PLBDIV 0x00030000 -#define CPC0_PLLMR0_CBDV 0x00030000 -#define PLL_PLBDIV_1 0x00000000 -#define PLL_PLBDIV_2 0x00010000 -#define PLL_PLBDIV_3 0x00020000 -#define PLL_PLBDIV_4 0x00030000 - /* OPB divisor */ -#define PLL_OPBDIV 0x00003000 -#define CPC0_PLLMR0_OPDV 0x00003000 -#define PLL_OPBDIV_1 0x00000000 -#define PLL_OPBDIV_2 0x00001000 -#define PLL_OPBDIV_3 0x00002000 -#define PLL_OPBDIV_4 0x00003000 - /* EBC divisor */ -#define PLL_EXTBUSDIV 0x00000300 -#define CPC0_PLLMR0_EPDV 0x00000300 -#define PLL_EXTBUSDIV_2 0x00000000 -#define PLL_EXTBUSDIV_3 0x00000100 -#define PLL_EXTBUSDIV_4 0x00000200 -#define PLL_EXTBUSDIV_5 0x00000300 - /* MAL divisor */ -#define PLL_MALDIV 0x00000030 -#define CPC0_PLLMR0_MPDV 0x00000030 -#define PLL_MALDIV_1 0x00000000 -#define PLL_MALDIV_2 0x00000010 -#define PLL_MALDIV_3 0x00000020 -#define PLL_MALDIV_4 0x00000030 - /* PCI divisor */ -#define PLL_PCIDIV 0x00000003 -#define CPC0_PLLMR0_PPFD 0x00000003 -#define PLL_PCIDIV_1 0x00000000 -#define PLL_PCIDIV_2 0x00000001 -#define PLL_PCIDIV_3 0x00000002 -#define PLL_PCIDIV_4 0x00000003 - -#ifdef CONFIG_PPCHAMELEON_CLK_25 -/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 25.0 MHz input clock to the 405EP) */ -#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_6 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) - -#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) - -/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */ -#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \ - PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \ - PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) - -#else -#error "* External frequency (SysClk) not defined! *" -#endif - -#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI) -/* Model HI */ -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55 -#define CONFIG_SYS_OPB_FREQ 55555555 -/* Model ME */ -#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME) -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33 -#define CONFIG_SYS_OPB_FREQ 66666666 -#else -/* Model BA (default) */ -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33 -#define CONFIG_SYS_OPB_FREQ 66666666 -#endif - -#endif /* CONFIG_NO_SERIAL_EEPROM */ - -#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ -#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */ - -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nand" -#define CONFIG_JFFS2_PART_SIZE 0x00200000 -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support - * - * Note: fake mtd_id used, no linux mtd map file - */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "nand0=catcenter" -#define MTDPARTS_DEFAULT "mtdparts=catcenter:2m(nand)" -*/ - -#endif /* __CONFIG_H */ diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h deleted file mode 100644 index e277d0d..0000000 --- a/include/configs/PPChameleonEVB.h +++ /dev/null @@ -1,777 +0,0 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, - * - * (C) Copyright 2003 - * DAVE Srl - * - * http://www.dave-tech.it - * http://www.wawnet.biz - * mailto:info@wawnet.biz - * - * Credits: Stefan Roese, Wolfgang Denk - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_PPCHAMELEON_MODULE_BA 0 /* Basic Model */ -#define CONFIG_PPCHAMELEON_MODULE_ME 1 /* Medium Model */ -#define CONFIG_PPCHAMELEON_MODULE_HI 2 /* High-End Model */ -#ifndef CONFIG_PPCHAMELEON_MODULE_MODEL -#define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA -#endif - - -/* Only one of the following two symbols must be defined (default is 25 MHz) - * CONFIG_PPCHAMELEON_CLK_25 - * CONFIG_PPCHAMELEON_CLK_33 - */ -#if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33)) -#define CONFIG_PPCHAMELEON_CLK_25 -#endif - -#if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33)) -#error "* Two external frequencies (SysClk) are defined! *" -#endif - -#undef CONFIG_PPCHAMELEON_SMI712 - -/* - * Debug stuff - */ -#undef __DEBUG_START_FROM_SRAM__ -#define __DISABLE_MACHINE_EXCEPTION__ - -#ifdef __DEBUG_START_FROM_SRAM__ -#define CONFIG_SYS_DUMMY_FLASH_SIZE 1024*1024*4 -#endif - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405EP 1 /* This is a PPC405 CPU */ -#define CONFIG_PPCHAMELEONEVB 1 /* ...on a PPChameleonEVB board */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFB0000 /* Reserve 320 kB for Monitor */ -#define CONFIG_SYS_LDSCRIPT "board/dave/PPChameleonEVB/u-boot.lds" - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ - - -#ifdef CONFIG_PPCHAMELEON_CLK_25 -# define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ -#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) -# define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ -#else -# error "* External frequency (SysClk) not defined! *" -#endif - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#undef CONFIG_BOOTARGS - -/* Ethernet stuff */ -#define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */ -#define CONFIG_ETHADDR 00:50:c2:1e:af:fe -#define CONFIG_HAS_ETH1 -#define CONFIG_ETH1ADDR 00:50:c2:1e:af:fd - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#undef CONFIG_EXT_PHY - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#ifndef CONFIG_EXT_PHY -#define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */ -#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */ -#else -#define CONFIG_PHY_ADDR 2 /* PHY address */ -#endif -#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NAND -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_SNTP - - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_RTC_M41T11 1 /* uses a M41T00 RTC */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_M41T11_BASE_YEAR 1900 - -/* - * SDRAM configuration (please see cpu/ppc/sdram.[ch]) - */ -#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ - -/* SDRAM timings used in datasheet */ -#define CONFIG_SYS_SDRAM_CL 2 -#define CONFIG_SYS_SDRAM_tRP 20 -#define CONFIG_SYS_SDRAM_tRC 65 -#define CONFIG_SYS_SDRAM_tRCD 20 -#undef CONFIG_SYS_SDRAM_tRFC - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ - -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ -#define CONFIG_SYS_BASE_BAUD 691200 - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ - 57600, 115200, 230400, 460800, 921600 } - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ - -/*----------------------------------------------------------------------- - * NAND-FLASH stuff - *----------------------------------------------------------------------- - */ - -/* - * nand device 1 on dave (PPChameleonEVB) needs more time, - * so we just introduce additional wait in nand_wait(), - * effectively for both devices. - */ -#define PPCHAMELON_NAND_TIMER_HACK - -#define CONFIG_SYS_NAND0_BASE 0xFF400000 -#define CONFIG_SYS_NAND1_BASE 0xFF000000 -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE, CONFIG_SYS_NAND1_BASE } -#define NAND_BIG_DELAY_US 25 -#define CONFIG_SYS_MAX_NAND_DEVICE 2 /* Max number of NAND devices */ - -#define CONFIG_SYS_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CONFIG_SYS_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ -#define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ - -#define CONFIG_SYS_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */ -#define CONFIG_SYS_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */ -#define CONFIG_SYS_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */ -#define CONFIG_SYS_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */ - -#define MACRO_NAND_DISABLE_CE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_ENABLE_CE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_CLRALE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_ALE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_ALE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_SETALE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_ALE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_ALE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_CLRCLE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CLE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CLE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_SETCLE(nandptr) do { \ - switch((unsigned long)nandptr) { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CLE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CLE); \ - break; \ - } \ -} while(0) - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#undef CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */ -#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ - -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ -#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* Reserve 256 kB for Monitor */ -/* -#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) -*/ - -/* Reserve 320 kB for Monitor */ -#define CONFIG_SYS_FLASH_BASE 0xFFFB0000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (320 * 1024) - -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ -#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ -#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ -/* - * The following defines are added for buggy IOP480 byte interface. - * All other boards should use the standard values (CPCI405 etc.) - */ -#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ -#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ -#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -/*----------------------------------------------------------------------- - * Environment Variable setup - */ -#ifdef ENVIRONMENT_IN_EEPROM - -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */ -#define CONFIG_ENV_SIZE 0x700 /* 2048-256 bytes may be used for env vars (total size of a CAT24WC16 is 2048 bytes)*/ - -#else /* DEFAULT: environment in flash, using redundand flash sectors */ - -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CONFIG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */ -#define CONFIG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/ -#define CONFIG_ENV_ADDR_REDUND 0xFFFFA000 -#define CONFIG_ENV_SIZE_REDUND 0x2000 - -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ - -#endif /* ENVIRONMENT_IN_EEPROM */ - - -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ -#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */ - -/*----------------------------------------------------------------------- - * I2C EEPROM (CAT24WC16) for environment - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ - /* 16 byte page write mode using*/ - /* last 4 bits of the address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */ - -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - */ - -/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x92015480 -#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ - -/* Memory Bank 1 (External SRAM) initialization */ -/* Since this must replace NOR Flash, we use the same settings for CS0 */ -#define CONFIG_SYS_EBC_PB1AP 0x92015480 -#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */ - -/* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x92015480 -#define CONFIG_SYS_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */ - -/* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x92015480 -#define CONFIG_SYS_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */ - -#ifdef CONFIG_PPCHAMELEON_SMI712 -/* - * Video console (graphic: SMI LynxEM) - */ -#define CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_SMI_LYNXEM -#define CONFIG_VIDEO_LOGO -/*#define CONFIG_VIDEO_BMP_LOGO*/ -#define CONFIG_CONSOLE_EXTRA_INFO -#define CONFIG_VGA_AS_SINGLE_DEVICE -/* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */ -#define CONFIG_SYS_ISA_IO 0xE8000000 -/* see also drivers/video/videomodes.c */ -#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x303 -#endif - -/*----------------------------------------------------------------------- - * FPGA stuff - */ -/* FPGA internal regs */ -#define CONFIG_SYS_FPGA_MODE 0x00 -#define CONFIG_SYS_FPGA_STATUS 0x02 -#define CONFIG_SYS_FPGA_TS 0x04 -#define CONFIG_SYS_FPGA_TS_LOW 0x06 -#define CONFIG_SYS_FPGA_TS_CAP0 0x10 -#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12 -#define CONFIG_SYS_FPGA_TS_CAP1 0x14 -#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16 -#define CONFIG_SYS_FPGA_TS_CAP2 0x18 -#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a -#define CONFIG_SYS_FPGA_TS_CAP3 0x1c -#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e - -/* FPGA Mode Reg */ -#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001 -#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100 -#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000 -#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000 - -/* FPGA Status Reg */ -#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001 -#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002 -#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004 -#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008 -#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000 - -#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ -#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ - -/* FPGA program pin configuration */ -#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ -#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ -#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ -#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ -#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in data cache) - */ -/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - -/* On Chip Memory location */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Definitions for GPIO setup (PPC405EP specific) - * - * GPIO0[0] - External Bus Controller BLAST output - * GPIO0[1-9] - Instruction trace outputs -> GPIO - * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs - * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO - * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs - * GPIO0[24-27] - UART0 control signal inputs/outputs - * GPIO0[28-29] - UART1 data signal input/output - * GPIO0[30] - EMAC0 input - * GPIO0[31] - EMAC1 reject packet as output - */ -#define CONFIG_SYS_GPIO0_OSRL 0x40000550 -#define CONFIG_SYS_GPIO0_OSRH 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 -/*#define CONFIG_SYS_GPIO0_ISR1H 0x15555445*/ -#define CONFIG_SYS_GPIO0_ISR1H 0x15555444 -#define CONFIG_SYS_GPIO0_TSRL 0x00000000 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 -#define CONFIG_SYS_GPIO0_TCR 0xF7FF8014 - -#define CONFIG_NO_SERIAL_EEPROM - -/*--------------------------------------------------------------------*/ - -#ifdef CONFIG_NO_SERIAL_EEPROM - -/* -!----------------------------------------------------------------------- -! Defines for entry options. -! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that -! are plugged in the board will be utilized as non-ECC DIMMs. -!----------------------------------------------------------------------- -*/ -#undef AUTO_MEMORY_CONFIG -#define DIMM_READ_ADDR 0xAB -#define DIMM_WRITE_ADDR 0xAA - -/* Defines for CPC0_PLLMR1 Register fields */ -#define PLL_ACTIVE 0x80000000 -#define CPC0_PLLMR1_SSCS 0x80000000 -#define PLL_RESET 0x40000000 -#define CPC0_PLLMR1_PLLR 0x40000000 - /* Feedback multiplier */ -#define PLL_FBKDIV 0x00F00000 -#define CPC0_PLLMR1_FBDV 0x00F00000 -#define PLL_FBKDIV_16 0x00000000 -#define PLL_FBKDIV_1 0x00100000 -#define PLL_FBKDIV_2 0x00200000 -#define PLL_FBKDIV_3 0x00300000 -#define PLL_FBKDIV_4 0x00400000 -#define PLL_FBKDIV_5 0x00500000 -#define PLL_FBKDIV_6 0x00600000 -#define PLL_FBKDIV_7 0x00700000 -#define PLL_FBKDIV_8 0x00800000 -#define PLL_FBKDIV_9 0x00900000 -#define PLL_FBKDIV_10 0x00A00000 -#define PLL_FBKDIV_11 0x00B00000 -#define PLL_FBKDIV_12 0x00C00000 -#define PLL_FBKDIV_13 0x00D00000 -#define PLL_FBKDIV_14 0x00E00000 -#define PLL_FBKDIV_15 0x00F00000 - /* Forward A divisor */ -#define PLL_FWDDIVA 0x00070000 -#define CPC0_PLLMR1_FWDVA 0x00070000 -#define PLL_FWDDIVA_8 0x00000000 -#define PLL_FWDDIVA_7 0x00010000 -#define PLL_FWDDIVA_6 0x00020000 -#define PLL_FWDDIVA_5 0x00030000 -#define PLL_FWDDIVA_4 0x00040000 -#define PLL_FWDDIVA_3 0x00050000 -#define PLL_FWDDIVA_2 0x00060000 -#define PLL_FWDDIVA_1 0x00070000 - /* Forward B divisor */ -#define PLL_FWDDIVB 0x00007000 -#define CPC0_PLLMR1_FWDVB 0x00007000 -#define PLL_FWDDIVB_8 0x00000000 -#define PLL_FWDDIVB_7 0x00001000 -#define PLL_FWDDIVB_6 0x00002000 -#define PLL_FWDDIVB_5 0x00003000 -#define PLL_FWDDIVB_4 0x00004000 -#define PLL_FWDDIVB_3 0x00005000 -#define PLL_FWDDIVB_2 0x00006000 -#define PLL_FWDDIVB_1 0x00007000 - /* PLL tune bits */ -#define PLL_TUNE_MASK 0x000003FF -#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */ -#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */ -#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */ -#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */ -#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */ -#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */ -#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */ - -/* Defines for CPC0_PLLMR0 Register fields */ - /* CPU divisor */ -#define PLL_CPUDIV 0x00300000 -#define CPC0_PLLMR0_CCDV 0x00300000 -#define PLL_CPUDIV_1 0x00000000 -#define PLL_CPUDIV_2 0x00100000 -#define PLL_CPUDIV_3 0x00200000 -#define PLL_CPUDIV_4 0x00300000 - /* PLB divisor */ -#define PLL_PLBDIV 0x00030000 -#define CPC0_PLLMR0_CBDV 0x00030000 -#define PLL_PLBDIV_1 0x00000000 -#define PLL_PLBDIV_2 0x00010000 -#define PLL_PLBDIV_3 0x00020000 -#define PLL_PLBDIV_4 0x00030000 - /* OPB divisor */ -#define PLL_OPBDIV 0x00003000 -#define CPC0_PLLMR0_OPDV 0x00003000 -#define PLL_OPBDIV_1 0x00000000 -#define PLL_OPBDIV_2 0x00001000 -#define PLL_OPBDIV_3 0x00002000 -#define PLL_OPBDIV_4 0x00003000 - /* EBC divisor */ -#define PLL_EXTBUSDIV 0x00000300 -#define CPC0_PLLMR0_EPDV 0x00000300 -#define PLL_EXTBUSDIV_2 0x00000000 -#define PLL_EXTBUSDIV_3 0x00000100 -#define PLL_EXTBUSDIV_4 0x00000200 -#define PLL_EXTBUSDIV_5 0x00000300 - /* MAL divisor */ -#define PLL_MALDIV 0x00000030 -#define CPC0_PLLMR0_MPDV 0x00000030 -#define PLL_MALDIV_1 0x00000000 -#define PLL_MALDIV_2 0x00000010 -#define PLL_MALDIV_3 0x00000020 -#define PLL_MALDIV_4 0x00000030 - /* PCI divisor */ -#define PLL_PCIDIV 0x00000003 -#define CPC0_PLLMR0_PPFD 0x00000003 -#define PLL_PCIDIV_1 0x00000000 -#define PLL_PCIDIV_2 0x00000001 -#define PLL_PCIDIV_3 0x00000002 -#define PLL_PCIDIV_4 0x00000003 - -#ifdef CONFIG_PPCHAMELEON_CLK_25 -/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 25.0 MHz input clock to the 405EP) */ -#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_6 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) - -#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) - -/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */ -#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \ - PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \ - PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) - -#else -#error "* External frequency (SysClk) not defined! *" -#endif - -#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI) -/* Model HI */ -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55 -#define CONFIG_SYS_OPB_FREQ 55555555 -/* Model ME */ -#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME) -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33 -#define CONFIG_SYS_OPB_FREQ 66666666 -#else -/* Model BA (default) */ -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33 -#define CONFIG_SYS_OPB_FREQ 66666666 -#endif - -#endif /* CONFIG_NO_SERIAL_EEPROM */ - -#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ -#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */ - -/* - * JFFS2 partitions - */ - -/* No command line, one static partition */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nand0" -#define CONFIG_JFFS2_PART_SIZE 0x00400000 -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "nor0=PPChameleon-0,nand0=ppchameleonevb-nand" -*/ - -/* 256 kB U-boot image */ -/* -#define MTDPARTS_DEFAULT "mtdparts=PPChameleon-0:1m(kernel1),1m(kernel2)," \ - "1792k(user),256k(u-boot);" \ - "ppchameleonevb-nand:-(nand)" -*/ - -/* 320 kB U-boot image */ -/* -#define MTDPARTS_DEFAULT "mtdparts=PPChameleon-0:1m(kernel1),1m(kernel2)," \ - "1728k(user),320k(u-boot);" \ - "ppchameleonevb-nand:-(nand)" -*/ - -#endif /* __CONFIG_H */