Whitebox
/
u-boot
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

powerpc/p1_p2_rdb_pc: Add a pin to reset the DDR chip for P1021RDB-PC

Browse Source 
When P1021RDB-PC reboot system, the board will hung at uboot DDR
configuration. For P1021RDB-PC DDR reset pin is multiplex with
QE, so uboot will reserve this pin for QE and skip DDR reset.
Other platforms without QE will do this reset. This patch adds
a slight code to reset DDR chip by QE CE_PB8 pin for NAND and
NOR FLASH boot. For booting from SPI FALSH and SD card, it
seems possible to use the rom on chip to write to the GPIO
pins before configuring the DDR.

Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
master
Xu Jiucheng 12 years ago committed by Andy Fleming
parent 1f06c9af31
commit 545c12cf9a
2 changed files with 33 additions and 1 deletions
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Show Stats Download Patch File Download Diff File
  1. 19
      board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
  2. 15
      board/freescale/p1_p2_rdb_pc/spl_minimal.c

19
board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
Unescape View File

@ -55,6 +55,13 @@
#define GPIO_SLIC_PIN 30
#define GPIO_SLIC_DATA (1 << (31 - GPIO_SLIC_PIN))
#if defined(CONFIG_P1021RDB) && !defined(CONFIG_SYS_RAMBOOT)
#define GPIO_DDR_RST_PORT 1
#define GPIO_DDR_RST_PIN 8
#define GPIO_DDR_RST_DATA (1 << (31 - GPIO_DDR_RST_PIN))
#define GPIO_2BIT_MASK (0x3 << (32 - (GPIO_DDR_RST_PIN + 1) * 2))
#endif
#if defined(CONFIG_P1025RDB) || defined(CONFIG_P1021RDB)
#define PCA_IOPORT_I2C_ADDR 0x23
@ -67,7 +74,7 @@
const qe_iop_conf_t qe_iop_conf_tab[] = {
/* GPIO */
{1, 1, 2, 0, 0}, /* GPIO7/PB1 - LOAD_DEFAULT_N */
#if 0
#if defined(CONFIG_P1021RDB) && !defined(CONFIG_SYS_RAMBOOT)
{1, 8, 1, 1, 0}, /* GPIO10/PB8 - DDR_RST */
#endif
{0, 15, 1, 0, 0}, /* GPIO11/A15 - WDI */
@ -159,6 +166,16 @@ void board_gpio_init(void)
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
par_io_t *par_io = (par_io_t *) &(gur->qe_par_io);
#if defined(CONFIG_P1021RDB) && !defined(CONFIG_SYS_RAMBOOT)
/* reset DDR3 */
setbits_be32(&par_io[GPIO_DDR_RST_PORT].cpdat, GPIO_DDR_RST_DATA);
udelay(1000);
clrbits_be32(&par_io[GPIO_DDR_RST_PORT].cpdat, GPIO_DDR_RST_DATA);
udelay(1000);
setbits_be32(&par_io[GPIO_DDR_RST_PORT].cpdat, GPIO_DDR_RST_DATA);
/* disable CE_PB8 */
clrbits_be32(&par_io[GPIO_DDR_RST_PORT].cpdir1, GPIO_2BIT_MASK);
#endif
/* Enable VSC7385 switch */
setbits_be32(&par_io[GPIO_GETH_SW_PORT].cpdat, GPIO_GETH_SW_DATA);

15
board/freescale/p1_p2_rdb_pc/spl_minimal.c
Unescape View File

@ -81,6 +81,8 @@ void board_init_f(ulong bootflag)
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
#ifndef CONFIG_QE
ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
#elif defined(CONFIG_P1021RDB)
par_io_t *par_io = (par_io_t *)&(gur->qe_par_io);
#endif
/* initialize selected port with appropriate baud rate */
@ -102,6 +104,19 @@ void board_init_f(ulong bootflag)
__raw_writel(0x00200000, &pgpio->gpdat);
udelay(1000);
__raw_writel(0x00000000, &pgpio->gpdir);
#elif defined(CONFIG_P1021RDB)
/* init DDR3 reset signal CE_PB8 */
out_be32(&par_io[1].cpdir1, 0x00004000);
out_be32(&par_io[1].cpodr, 0x00800000);
out_be32(&par_io[1].cppar1, 0x00000000);
/* reset DDR3 */
out_be32(&par_io[1].cpdat, 0x00800000);
udelay(1000);
out_be32(&par_io[1].cpdat, 0x00000000);
udelay(1000);
out_be32(&par_io[1].cpdat, 0x00800000);
/* disable the CE_PB8 */
out_be32(&par_io[1].cpdir1, 0x00000000);
#endif
#ifndef CONFIG_SYS_INIT_L2_ADDR

Write Preview
Loading…
Cancel
Save