mpc8323erdb: Improve the system performance

The following changes are based on kernel UCC ethernet performance:

1.  Make the CSB bus pipeline depth as 4, and enable the repeat mode
2.  Optimize transactions between QE and CSB.  Added CFG_SPCR_OPT
    switch to enable this setting.

The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:

3.  CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4.  CS0_CONFIG[ODT_WR_CONFIG] set to 1.  Was a reserved setting
    previously.
5.  TIMING_CFG_1[WRREC] is changed from 3clks to 2clks  (based on
    Twr=15ns, and this was already the setting in DDR_MODE)
6.  TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
    Trp=15ns)
7.  TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
    Tras=40ns)
8.  TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
    Trcd=15ns)
9.  TIMING_CFG_1[REFREC] changed from 21 clks to 11clks.  (based on
    Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks.  (based
    on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
    on CL=3 and WL=2).

Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

cpu/mpc83xx/cpu_init.c

@@ -79,6 +79,12 @@ void cpu_init_f (volatile immap_t * im)
 			  (CFG_ACR_RPTCNT << ACR_RPTCNT_SHIFT);
 #endif
 
+#ifdef CFG_SPCR_OPT
+	/* Optimize transactions between CSB and other devices */
+	im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_OPT) |
+			   (CFG_SPCR_OPT << SPCR_OPT_SHIFT);
+#endif
+
 #ifdef CFG_SPCR_TSECEP
 	/* all eTSEC's Emergency priority */
 	im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSECEP) |

include/configs/MPC8323ERDB.h

@@ -66,6 +66,13 @@
 #define CFG_IMMR		0xE0000000
 
 /*
+ * System performance
+ */
+#define CFG_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
+#define CFG_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
+#define CFG_SPCR_OPT		1	/* (0-1) Optimize transactions between  CSB and the SEC and QUICC Engine block */
+
+/*
  * DDR Setup
  */
 #define CFG_DDR_BASE		0x00000000	/* DDR is system memory */
@@ -83,10 +90,9 @@
  */
 #define CFG_DDR_SIZE		64	/* MB */
 #define CFG_DDR_CS0_CONFIG	( CSCONFIG_EN \
-				| CSCONFIG_AP \
-				| 0x00040000 /* TODO */ \
+				| CSCONFIG_ODT_WR_ACS \
 				| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9 )
-				/* 0x80840101 */
+				/* 0x80010101 */
 #define CFG_DDR_TIMING_0	( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_RRT_SHIFT ) \
@@ -96,28 +102,29 @@
 				| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
 				| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
 				/* 0x00220802 */
-#define CFG_DDR_TIMING_1	( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
-				| ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
-				| ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
+#define CFG_DDR_TIMING_1	( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
+				| ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+				| ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \
 				| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
-				| (13 << TIMING_CFG1_REFREC_SHIFT ) \
-				| ( 3 << TIMING_CFG1_WRREC_SHIFT ) \
+				| ( 3 << TIMING_CFG1_REFREC_SHIFT ) \
+				| ( 2 << TIMING_CFG1_WRREC_SHIFT ) \
 				| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
 				| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
-				/* 0x3935d322 */
-#define CFG_DDR_TIMING_2	( (31 << TIMING_CFG2_CPO_SHIFT ) \
+				/* 0x26253222 */
+#define CFG_DDR_TIMING_2	( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+				| (31 << TIMING_CFG2_CPO_SHIFT ) \
 				| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
 				| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
 				| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
 				| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
-				| (10 << TIMING_CFG2_FOUR_ACT_SHIFT) )
-				/* 0x0f9048ca */
+				| ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+				/* 0x1f9048c7 */
 #define CFG_DDR_TIMING_3	0x00000000
 #define CFG_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 				/* 0x02000000 */
-#define CFG_DDR_MODE		( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \
+#define CFG_DDR_MODE		( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
 				| ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
-				/* 0x44400232 */
+				/* 0x44480232 */
 #define CFG_DDR_MODE2		0x8000c000
 #define CFG_DDR_INTERVAL	( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
 				| ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )

include/mpc83xx.h

@@ -121,6 +121,7 @@
 #define SPCR_PCIPR			0x03000000	/* PCI bridge system bus request priority */
 #define SPCR_PCIPR_SHIFT		(31-7)
 #define SPCR_OPT			0x00800000	/* Optimize */
+#define SPCR_OPT_SHIFT			(31-8)
 #define SPCR_TBEN			0x00400000	/* E300 PowerPC core time base unit enable */
 #define SPCR_TBEN_SHIFT			(31-9)
 #define SPCR_COREPR			0x00300000	/* E300 PowerPC Core system bus request priority */