armv8: ls1012ardb: support hwconfig for eSDHC1 enabling

I2C reading for DIP switch setting is not reliable for LS1012ARDB
RevD and later versions. This patch is to add hwconfig support to
enable/disable eSDHC1 manually for these boards. Also drop 'status'
fix-up for eSDHC0 and leave it as it is. It shouldn't always be
fixed up with 'okay'.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

board/freescale/ls1012ardb/ls1012ardb.c

@@ -152,34 +152,49 @@ int board_init(void)
 
 int esdhc_status_fixup(void *blob, const char *compat)
 {
-	char esdhc0_path[] = "/soc/esdhc@1560000";
 	char esdhc1_path[] = "/soc/esdhc@1580000";
-	u8 io = 0;
+	bool sdhc2_en = false;
 	u8 mux_sdhc2;
-
-	do_fixup_by_path(blob, esdhc0_path, "status", "okay",
-			 sizeof("okay"), 1);
+	u8 io = 0;
 
 	i2c_set_bus_num(0);
 
-	/*
-	 * The I2C IO-expander for mux select is used to control the muxing
-	 * of various onboard interfaces.
-	 *
-	 * IO1[3:2] indicates SDHC2 interface demultiplexer select lines.
-	 *	00 - SDIO wifi
-	 *	01 - GPIO (to Arduino)
-	 *	10 - eMMC Memory
-	 *	11 - SPI
-	 */
-	if (i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_0, 1, &io, 1) < 0) {
+	/* IO1[7:3] is the field of board revision info. */
+	if (i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_1, 1, &io, 1) < 0) {
 		printf("Error reading i2c boot information!\n");
-		return 0; /* Don't want to hang() on this error */
+		return 0;
+	}
+
+	/* hwconfig method is used for RevD and later versions. */
+	if ((io & SW_REV_MASK) <= SW_REV_D) {
+#ifdef CONFIG_HWCONFIG
+		if (hwconfig("esdhc1"))
+			sdhc2_en = true;
+#endif
+	} else {
+		/*
+		 * The I2C IO-expander for mux select is used to control
+		 * the muxing of various onboard interfaces.
+		 *
+		 * IO0[3:2] indicates SDHC2 interface demultiplexer
+		 * select lines.
+		 *	00 - SDIO wifi
+		 *	01 - GPIO (to Arduino)
+		 *	10 - eMMC Memory
+		 *	11 - SPI
+		 */
+		if (i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_0, 1, &io, 1) < 0) {
+			printf("Error reading i2c boot information!\n");
+			return 0;
+		}
+
+		mux_sdhc2 = (io & 0x0c) >> 2;
+		/* Enable SDHC2 only when use SDIO wifi and eMMC */
+		if (mux_sdhc2 == 2 || mux_sdhc2 == 0)
+			sdhc2_en = true;
 	}
 
-	mux_sdhc2 = (io & 0x0c) >> 2;
-	/* Enable SDHC2 only when use SDIO wifi and eMMC */
-	if (mux_sdhc2 == 2 || mux_sdhc2 == 0)
+	if (sdhc2_en)
 		do_fixup_by_path(blob, esdhc1_path, "status", "okay",
 				 sizeof("okay"), 1);
 	else