diff --git a/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c b/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c index eec06bc..df7d6a2 100644 --- a/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c +++ b/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c @@ -32,6 +32,7 @@ #include #include +#if defined(CONFIG_SYS_DA850_PLL_INIT) void da850_waitloop(unsigned long loopcnt) { unsigned long i; @@ -163,7 +164,9 @@ int da850_pll_init(struct davinci_pllc_regs *reg, unsigned long pllmult) return 0; } +#endif /* CONFIG_SYS_DA850_PLL_INIT */ +#if defined(CONFIG_SYS_DA850_DDR_INIT) int da850_ddr_setup(void) { unsigned long tmp; @@ -242,6 +245,7 @@ int da850_ddr_setup(void) return 0; } +#endif /* CONFIG_SYS_DA850_DDR_INIT */ __attribute__((weak)) void board_gpio_init(void) @@ -249,10 +253,6 @@ void board_gpio_init(void) return; } -/* pinmux_resource[] vector is defined in the board specific file */ -extern const struct pinmux_resource pinmuxes[]; -extern const int pinmuxes_size; - int arch_cpu_init(void) { /* Unlock kick registers */ @@ -266,13 +266,11 @@ int arch_cpu_init(void) if (davinci_configure_pin_mux_items(pinmuxes, pinmuxes_size)) return 1; +#if defined(CONFIG_SYS_DA850_PLL_INIT) /* PLL setup */ da850_pll_init(davinci_pllc0_regs, CONFIG_SYS_DA850_PLL0_PLLM); da850_pll_init(davinci_pllc1_regs, CONFIG_SYS_DA850_PLL1_PLLM); - - /* GPIO setup */ - board_gpio_init(); - +#endif /* setup CSn config */ #if defined(CONFIG_SYS_DA850_CS2CFG) writel(CONFIG_SYS_DA850_CS2CFG, &davinci_emif_regs->ab1cr); @@ -281,7 +279,12 @@ int arch_cpu_init(void) writel(CONFIG_SYS_DA850_CS3CFG, &davinci_emif_regs->ab2cr); #endif - lpsc_on(CONFIG_SYS_DA850_LPSC_UART); + da8xx_configure_lpsc_items(lpsc, lpsc_size); + + /* GPIO setup */ + board_gpio_init(); + + NS16550_init((NS16550_t)(CONFIG_SYS_NS16550_COM1), CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE); @@ -293,6 +296,9 @@ int arch_cpu_init(void) DAVINCI_UART_PWREMU_MGMT_UTRST), &davinci_uart2_ctrl_regs->pwremu_mgmt); +#if defined(CONFIG_SYS_DA850_DDR_INIT) da850_ddr_setup(); +#endif + return 0; } diff --git a/arch/arm/cpu/arm926ejs/davinci/spl.c b/arch/arm/cpu/arm926ejs/davinci/spl.c index f475f9b..74632e5 100644 --- a/arch/arm/cpu/arm926ejs/davinci/spl.c +++ b/arch/arm/cpu/arm926ejs/davinci/spl.c @@ -74,12 +74,12 @@ void board_init_f(ulong dummy) void board_init_r(gd_t *id, ulong dummy) { -#ifdef CONFIG_SOC_DM365 +#ifdef CONFIG_SPL_NAND_LOAD nand_init(); puts("Nand boot...\n"); nand_boot(); #endif -#ifdef CONFIG_SOC_DA8XX +#ifdef CONFIG_SPL_SPI_LOAD mem_malloc_init(CONFIG_SYS_TEXT_BASE - CONFIG_SYS_MALLOC_LEN, CONFIG_SYS_MALLOC_LEN); diff --git a/arch/arm/include/asm/arch-davinci/da850_lowlevel.h b/arch/arm/include/asm/arch-davinci/da850_lowlevel.h index e489c47..11ed91d 100644 --- a/arch/arm/include/asm/arch-davinci/da850_lowlevel.h +++ b/arch/arm/include/asm/arch-davinci/da850_lowlevel.h @@ -24,6 +24,15 @@ #ifndef __DA850_LOWLEVEL_H #define __DA850_LOWLEVEL_H +#include + +/* pinmux_resource[] vector is defined in the board specific file */ +extern const struct pinmux_resource pinmuxes[]; +extern const int pinmuxes_size; + +extern const struct lpsc_resource lpsc[]; +extern const int lpsc_size; + /* NOR Boot Configuration Word Field Descriptions */ #define DA850_NORBOOT_COPY_XK(X) ((X - 1) << 8) #define DA850_NORBOOT_METHOD_DIRECT (1 << 4) diff --git a/board/davinci/da8xxevm/da850evm.c b/board/davinci/da8xxevm/da850evm.c index 9bd3e71..34ef53d 100644 --- a/board/davinci/da8xxevm/da850evm.c +++ b/board/davinci/da8xxevm/da850evm.c @@ -137,7 +137,7 @@ const struct pinmux_resource pinmuxes[] = { const int pinmuxes_size = ARRAY_SIZE(pinmuxes); -static const struct lpsc_resource lpsc[] = { +const struct lpsc_resource lpsc[] = { { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */ { DAVINCI_LPSC_SPI1 }, /* Serial Flash */ { DAVINCI_LPSC_EMAC }, /* image download */ @@ -145,6 +145,8 @@ static const struct lpsc_resource lpsc[] = { { DAVINCI_LPSC_GPIO }, }; +const int lpsc_size = ARRAY_SIZE(lpsc); + #ifndef CONFIG_DA850_EVM_MAX_CPU_CLK #define CONFIG_DA850_EVM_MAX_CPU_CLK 300000000 #endif diff --git a/board/davinci/da8xxevm/hawkboard.c b/board/davinci/da8xxevm/hawkboard.c index 9d4e238..b694258 100644 --- a/board/davinci/da8xxevm/hawkboard.c +++ b/board/davinci/da8xxevm/hawkboard.c @@ -27,10 +27,33 @@ #include #include #include +#include #include DECLARE_GLOBAL_DATA_PTR; +const struct pinmux_resource pinmuxes[] = { + PINMUX_ITEM(emac_pins_mii), + PINMUX_ITEM(emac_pins_mdio), + PINMUX_ITEM(emifa_pins_cs3), + PINMUX_ITEM(emifa_pins_cs4), + PINMUX_ITEM(emifa_pins_nand), + PINMUX_ITEM(uart2_pins_txrx), + PINMUX_ITEM(uart2_pins_rtscts), +}; + +const int pinmuxes_size = ARRAY_SIZE(pinmuxes); + +const struct lpsc_resource lpsc[] = { + { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */ + { DAVINCI_LPSC_SPI1 }, /* Serial Flash */ + { DAVINCI_LPSC_EMAC }, /* image download */ + { DAVINCI_LPSC_UART2 }, /* console */ + { DAVINCI_LPSC_GPIO }, +}; + +const int lpsc_size = ARRAY_SIZE(lpsc); + int board_init(void) { /* arch number of the board */ diff --git a/board/davinci/da8xxevm/hawkboard_nand_spl.c b/board/davinci/da8xxevm/hawkboard_nand_spl.c deleted file mode 100644 index df97963..0000000 --- a/board/davinci/da8xxevm/hawkboard_nand_spl.c +++ /dev/null @@ -1,115 +0,0 @@ -/* - * Modified for Hawkboard - Syed Mohammed Khasim - * - * Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc. - * Copyright (C) 2007 Sergey Kubushyn - * Copyright (C) 2004 Texas Instruments. - * - * ---------------------------------------------------------------------------- - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - * ---------------------------------------------------------------------------- - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -static const struct pinmux_resource pinmuxes[] = { - PINMUX_ITEM(emac_pins_mii), - PINMUX_ITEM(emac_pins_mdio), - PINMUX_ITEM(emifa_pins_cs3), - PINMUX_ITEM(emifa_pins_cs4), - PINMUX_ITEM(emifa_pins_nand), - PINMUX_ITEM(uart2_pins_txrx), - PINMUX_ITEM(uart2_pins_rtscts), -}; - -static const struct lpsc_resource lpsc[] = { - { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */ - { DAVINCI_LPSC_SPI1 }, /* Serial Flash */ - { DAVINCI_LPSC_EMAC }, /* image download */ - { DAVINCI_LPSC_UART2 }, /* console */ - { DAVINCI_LPSC_GPIO }, -}; - -void board_init_f(ulong bootflag) -{ - /* - * Kick Registers need to be set to allow access to Pin Mux registers - */ - writel(DV_SYSCFG_KICK0_UNLOCK, &davinci_syscfg_regs->kick0); - writel(DV_SYSCFG_KICK1_UNLOCK, &davinci_syscfg_regs->kick1); - - /* setup the SUSPSRC for ARM to control emulation suspend */ - writel(readl(&davinci_syscfg_regs->suspsrc) & - ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C | - DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 | - DAVINCI_SYSCFG_SUSPSRC_UART2), &davinci_syscfg_regs->suspsrc); - - /* Power on required peripherals - * ARM does not have acess by default to PSC0 and PSC1 - * assuming here that the DSP bootloader has set the IOPU - * such that PSC access is available to ARM - */ - da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)); - - /* configure pinmux settings */ - davinci_configure_pin_mux_items(pinmuxes, - ARRAY_SIZE(pinmuxes)); - - writel(readl(&davinci_uart2_ctrl_regs->pwremu_mgmt) | - (DAVINCI_UART_PWREMU_MGMT_FREE) | - (DAVINCI_UART_PWREMU_MGMT_URRST) | - (DAVINCI_UART_PWREMU_MGMT_UTRST), - &davinci_uart2_ctrl_regs->pwremu_mgmt); - - NS16550_init((NS16550_t)(DAVINCI_UART2_BASE), - CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE); - - puts("Nand boot...\n"); - - nand_boot(); -} - -void puts(const char *str) -{ - while (*str) - putc(*str++); -} - -void putc(char c) -{ - if (gd->flags & GD_FLG_SILENT) - return; - - if (c == '\n') - NS16550_putc((NS16550_t)(DAVINCI_UART2_BASE), '\r'); - - NS16550_putc((NS16550_t)(DAVINCI_UART2_BASE), c); -} - -void hang(void) -{ - puts("### ERROR ### Please RESET the board ###\n"); - for (;;) - ; -} diff --git a/board/davinci/da8xxevm/u-boot-spl.lds b/board/davinci/da8xxevm/u-boot-spl-da850evm.lds similarity index 100% rename from board/davinci/da8xxevm/u-boot-spl.lds rename to board/davinci/da8xxevm/u-boot-spl-da850evm.lds diff --git a/nand_spl/board/davinci/da8xxevm/u-boot.lds b/board/davinci/da8xxevm/u-boot-spl-hawk.lds similarity index 86% rename from nand_spl/board/davinci/da8xxevm/u-boot.lds rename to board/davinci/da8xxevm/u-boot-spl-hawk.lds index 638ffd9..b3a41af 100644 --- a/nand_spl/board/davinci/da8xxevm/u-boot.lds +++ b/board/davinci/da8xxevm/u-boot-spl-hawk.lds @@ -34,11 +34,11 @@ SECTIONS . = ALIGN(4); .text : { - start.o (.text) - cpu.o (.text) - nand_boot.o (.text) + arch/arm/cpu/arm926ejs/start.o (.text) + arch/arm/cpu/arm926ejs/davinci/libdavinci.o (.text) + drivers/mtd/nand/libnand.o (.text) - *(.text) + *(.text*) } . = ALIGN(4); @@ -68,10 +68,14 @@ SECTIONS __got_end = .; - _end = .; + .bss : + { + . = ALIGN(4); + __bss_start = .; + *(.bss*) + . = ALIGN(4); + __bss_end__ = .; + } - . = ALIGN(4); - __bss_start = .; - .bss : { *(.bss) } - __bss_end__ = .; + _end = .; } diff --git a/board/enbw/enbw_cmc/enbw_cmc.c b/board/enbw/enbw_cmc/enbw_cmc.c index 98dda1e..16d1b08 100644 --- a/board/enbw/enbw_cmc/enbw_cmc.c +++ b/board/enbw/enbw_cmc/enbw_cmc.c @@ -49,7 +49,7 @@ DECLARE_GLOBAL_DATA_PTR; -static const struct lpsc_resource lpsc[] = { +const struct lpsc_resource lpsc[] = { { DAVINCI_LPSC_AEMIF }, { DAVINCI_LPSC_SPI1 }, { DAVINCI_LPSC_ARM_RAM_ROM }, @@ -65,6 +65,8 @@ static const struct lpsc_resource lpsc[] = { { DAVINCI_LPSC_USB11 }, }; +const int lpsc_size = ARRAY_SIZE(lpsc); + static const struct pinmux_config enbw_pins[] = { { pinmux(0), 8, 0 }, { pinmux(0), 8, 1 }, @@ -549,15 +551,6 @@ void board_gpio_init(void) struct davinci_gpio *gpio = davinci_gpio_bank01; /* - * Power on required peripherals - * ARM does not have access by default to PSC0 and PSC1 - * assuming here that the DSP bootloader has set the IOPU - * such that PSC access is available to ARM - */ - if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc))) - return; - - /* * set LED (gpio Interface not usable here) * set LED pins to output and state 0 */ diff --git a/boards.cfg b/boards.cfg index ceaf9ac..0c39625 100644 --- a/boards.cfg +++ b/boards.cfg @@ -133,7 +133,6 @@ davinci_sffsdr arm arm926ejs sffsdr davinci davinci_sonata arm arm926ejs sonata davinci davinci ea20 arm arm926ejs ea20 davinci davinci hawkboard arm arm926ejs da8xxevm davinci davinci -hawkboard_nand arm arm926ejs da8xxevm davinci davinci hawkboard:NAND_U_BOOT hawkboard_uart arm arm926ejs da8xxevm davinci davinci hawkboard:UART_U_BOOT enbw_cmc arm arm926ejs enbw_cmc enbw davinci dns325 arm arm926ejs - d-link kirkwood diff --git a/doc/README.hawkboard b/doc/README.hawkboard index b7afec4..d6ae02e 100644 --- a/doc/README.hawkboard +++ b/doc/README.hawkboard @@ -9,8 +9,8 @@ executes upon reset is the Rom Boot Loader(RBL) which sits in the internal ROM of the omap. The RBL initialises the memory and the nand controller, and copies the image stored at a predefined location(block 1) of the nand flash. The image loaded by the RBL to the memory is the -AIS signed nand_spl image. This, in turns copies the u-boot binary -from the nand flash to the memory and jumps to the u-boot entry point. +AIS signed spl image. This, in turns copies the u-boot binary from the +nand flash to the memory and jumps to the u-boot entry point. AIS is an image format defined by TI for the images that are to be loaded to memory by the RBL. The image is divided into a series of @@ -20,14 +20,14 @@ and the size of the section, which is used by the RBL to load the image. At the end of the image the RBL jumps to the image entry point. -The secondary stage bootloader(nand_spl) which is loaded by the RBL -then loads the u-boot from a predefined location in the nand to the -memory and jumps to the u-boot entry point. +The secondary stage bootloader(spl) which is loaded by the RBL then +loads the u-boot from a predefined location in the nand to the memory +and jumps to the u-boot entry point. The reason a secondary stage bootloader is used is because the ECC layout expected by the RBL is not the same as that used by -u-boot/linux. This also implies that for flashing the nand_spl image, -we need to use the u-boot which uses the ECC layout expected by the +u-boot/linux. This also implies that for flashing the spl image,we +need to use the u-boot which uses the ECC layout expected by the RBL[1]. Booting u-boot over UART(UART boot) is explained here[2]. @@ -35,20 +35,19 @@ Compilation =========== Three images might be needed -* nand_spl - This is the secondary bootloader which boots the u-boot +* spl - This is the secondary bootloader which boots the u-boot binary. - hawkboard_nand_config - - The nand_spl ELF gets generated under nand_spl/u-boot-spl. This - needs to be processed with the AISGen tool for generating the AIS - signed image to be flashed. Steps for generating the AIS image are - explained here[3]. - * u-boot binary - This is the image flashed to the nand and copied to - the memory by the nand_spl. + the memory by the spl. + + Both the images get compiled with hawkboard_config, with the TOPDIR + containing the u-boot images, and the spl image under the spl + directory. - hawkboard_config + The spl image needs to be processed with the AISGen tool for + generating the AIS signed image to be flashed. Steps for generating + the AIS image are explained here[3]. * u-boot for uart boot - This is same as the u-boot binary generated above, with the sole difference of the CONFIG_SYS_TEXT_BASE being @@ -59,17 +58,17 @@ Three images might be needed Flashing the images to Nand =========================== -The nand_spl AIS image needs to be flashed to the block 1 of the -Nand flash, as that is the location the RBL expects the image[4]. For -flashing the nand_spl, boot over the u-boot specified in [1], and -flash the image +The spl AIS image needs to be flashed to the block 1 of the Nand +flash, as that is the location the RBL expects the image[4]. For +flashing the spl, boot over the u-boot specified in [1], and flash the +image => tftpboot 0xc0700000 => nand erase 0x20000 0x20000 => nand write.e 0xc0700000 0x20000 The u-boot binary is flashed at location 0xe0000(block 6) of the nand -flash. The nand_spl loader expects the u-boot at this location. For +flash. The spl loader expects the u-boot at this location. For flashing the u-boot binary => tftpboot 0xc0700000 u-boot.bin diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index 8e0293d..989472b 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -44,6 +44,8 @@ #define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) #define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_TEXT_BASE 0xc1080000 +#define CONFIG_SYS_DA850_PLL_INIT +#define CONFIG_SYS_DA850_DDR_INIT /* * Memory Info @@ -142,7 +144,6 @@ #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ #define CONFIG_BAUDRATE 115200 /* Default baud rate */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CONFIG_SYS_DA850_LPSC_UART DAVINCI_LPSC_UART2 #define CONFIG_SPI #define CONFIG_SPI_FLASH @@ -322,7 +323,7 @@ #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_LIBCOMMON_SUPPORT #define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_LDSCRIPT "$(BOARDDIR)/u-boot-spl.lds" +#define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-da850evm.lds" #define CONFIG_SPL_STACK 0x8001ff00 #define CONFIG_SPL_TEXT_BASE 0x80000000 #define CONFIG_SPL_MAX_SIZE 32768 diff --git a/include/configs/enbw_cmc.h b/include/configs/enbw_cmc.h index 053cfa4..29b0d33 100644 --- a/include/configs/enbw_cmc.h +++ b/include/configs/enbw_cmc.h @@ -48,6 +48,8 @@ #define CONFIG_SYS_HZ 1000 #define CONFIG_DA850_LOWLEVEL #define CONFIG_ARCH_CPU_INIT +#define CONFIG_SYS_DA850_PLL_INIT +#define CONFIG_SYS_DA850_DDR_INIT #define CONFIG_DA8XX_GPIO #define CONFIG_HOSTNAME enbw_cmc @@ -82,7 +84,7 @@ #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ #define CONFIG_BAUDRATE 115200 /* Default baud rate */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CONFIG_SYS_DA850_LPSC_UART DAVINCI_LPSC_UART2 + /* * I2C Configuration */ diff --git a/include/configs/hawkboard.h b/include/configs/hawkboard.h index c310c73..50a1c17 100644 --- a/include/configs/hawkboard.h +++ b/include/configs/hawkboard.h @@ -44,12 +44,29 @@ #define CONFIG_SKIP_LOWLEVEL_INIT #define CONFIG_BOARD_EARLY_INIT_F -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_UART_U_BOOT) +#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \ + DAVINCI_SYSCFG_SUSPSRC_EMAC | \ + DAVINCI_SYSCFG_SUSPSRC_I2C | \ + DAVINCI_SYSCFG_SUSPSRC_SPI1 | \ + DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \ + DAVINCI_SYSCFG_SUSPSRC_UART2) + +#if defined(CONFIG_UART_U_BOOT) #define CONFIG_SYS_TEXT_BASE 0xc1080000 -#else +#elif !defined(CONFIG_SPL_BUILD) #define CONFIG_SYS_TEXT_BASE 0xc1180000 #endif +/* Spl */ +#define CONFIG_SPL +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_SIMPLE +#define CONFIG_SPL_NAND_LOAD +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-hawk.lds" +#define CONFIG_SPL_TEXT_BASE 0xc1080000 +#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR + /* * Memory Info */ @@ -85,9 +102,7 @@ /* * Network & Ethernet Configuration */ -#if !defined(CONFIG_NAND_SPL) #define CONFIG_DRIVER_TI_EMAC -#endif #define CONFIG_MII #define CONFIG_BOOTP_DEFAULT #define CONFIG_BOOTP_DNS diff --git a/nand_spl/board/davinci/da8xxevm/Makefile b/nand_spl/board/davinci/da8xxevm/Makefile deleted file mode 100644 index 7746e41..0000000 --- a/nand_spl/board/davinci/da8xxevm/Makefile +++ /dev/null @@ -1,155 +0,0 @@ -# -# (C) Copyright 2006-2007 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# -# (C) Copyright 2008 -# Guennadi Liakhovetki, DENX Software Engineering, -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -CONFIG_NAND_SPL = y - -include $(TOPDIR)/config.mk - -nandobj := $(OBJTREE)/nand_spl/ - -LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds -LDFLAGS := -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(LDFLAGS) \ - $(LDFLAGS_FINAL) -AFLAGS += -DCONFIG_SPL_BUILD -DCONFIG_NAND_SPL -CFLAGS += -DCONFIG_SPL_BUILD -DCONFIG_NAND_SPL - -SOBJS = _divsi3.o \ - _udivsi3.o \ - start.o - -COBJS = cpu.o \ - davinci_nand.o \ - pinmux.o \ - da850_pinmux.o \ - div0.o \ - hawkboard_nand_spl.o \ - misc.o \ - nand_boot.o \ - ns16550.o \ - psc.o - -SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) -OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) -__OBJS := $(SOBJS) $(COBJS) -LNDIR := $(nandobj)board/$(BOARDDIR) - -ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin \ - $(nandobj)u-boot-spl-16k.bin - -all: $(ALL) - -$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl - $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ - -$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl - $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ - -$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds - cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \ - -Map $(nandobj)u-boot-spl.map \ - -o $(nandobj)u-boot-spl - -$(nandobj)u-boot.lds: $(LDSCRIPT) - $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ - -# create symbolic links for common files - -# from board directory -$(obj)pinmux.c: - @rm -f $@ - @ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/pinmux.c $@ - -$(obj)da850_pinmux.c: - @rm -f $@ - @ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c $@ - -# from drivers/mtd/nand directory -$(obj)davinci_nand.c: - @rm -f $@ - @ln -s $(TOPDIR)/drivers/mtd/nand/davinci_nand.c $@ - -# from nand_spl directory -$(obj)nand_boot.c: - @rm -f $@ - @ln -s $(TOPDIR)/nand_spl/nand_boot.c $@ - -# from drivers/serial directory -$(obj)ns16550.c: - @rm -f $@ - @ln -sf $(TOPDIR)/drivers/serial/ns16550.c $@ - -# from cpu directory -$(obj)start.S: - @rm -f $@ - ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/start.S $@ - -# from lib directory -$(obj)_udivsi3.S: - @rm -f $@ - ln -s $(TOPDIR)/arch/arm/lib/_udivsi3.S $@ - -# from lib directory -$(obj)_divsi3.S: - @rm -f $@ - ln -s $(TOPDIR)/arch/arm/lib/_divsi3.S $@ - -# from lib directory -$(obj)div0.c: - @rm -f $@ - ln -s $(TOPDIR)/arch/arm/lib/div0.c $@ - -# from SoC directory -$(obj)cpu.c: - @rm -f $@ - @ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/cpu.c $@ - -$(obj)misc.c: - @rm -f $@ - ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/misc.c $@ - -# from board directory -$(obj)hawkboard_nand_spl.c: - @rm -f $@ - ln -s $(TOPDIR)/board/davinci/da8xxevm/hawkboard_nand_spl.c $@ - -$(obj)psc.c: - @rm -f $@ - ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/psc.c $@ - -######################################################################### - -$(obj)%.o: $(obj)%.S - $(CC) $(AFLAGS) -c -o $@ $< - -$(obj)%.o: $(obj)%.c - $(CC) $(CFLAGS) -c -o $@ $< - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -#########################################################################