armv8: layerscape: Adjust memory mapping for Flash/SD card on LS1046A

This patch is to adjust the memory mapping for FLash/SD card on
LS1046AQDS and LS1046ARDB, such as FMAN firmware load address, U-Boot
start address on serial flash and environment address.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

board/freescale/ls1046ardb/README

@@ -59,14 +59,14 @@ Start Address	 End Address	 Description		Size
 QSPI flash map:
 Start Address    End Address     Description		Size
 0x00_4000_0000 - 0x00_400F_FFFF  RCW + PBI		1MB
-0x00_4010_0000 - 0x00_401F_FFFF  U-Boot 		1MB
-0x00_4020_0000 - 0x00_402F_FFFF  U-Boot Env		1MB
-0x00_4030_0000 - 0x00_403F_FFFF  FMan ucode		1MB
-0x00_4040_0000 - 0x00_404F_FFFF  UEFI			1MB
-0x00_4050_0000 - 0x00_406F_FFFF  PPA			2MB
-0x00_4070_0000 - 0x00_408F_FFFF  Secure boot header
-			         + bootscript		2MB
-0x00_4090_0000 - 0x00_40FF_FFFF  Reserved		7MB
+0x00_4010_0000 - 0x00_402F_FFFF  U-Boot 		2MB
+0x00_4030_0000 - 0x00_403F_FFFF  U-Boot Env		1MB
+0x00_4040_0000 - 0x00_405F_FFFF  PPA			2MB
+0x00_4060_0000 - 0x00_408F_FFFF  Secure boot header
+				 + bootscript		3MB
+0x00_4090_0000 - 0x00_4093_FFFF  FMan ucode		256KB
+0x00_4094_0000 - 0x00_4097_FFFF  QE/uQE firmware	256KB
+0x00_4098_0000 - 0x00_40FF_FFFF  Reserved		6MB
 0x00_4100_0000 - 0x00_43FF_FFFF  FIT Image		48MB
 
 Booting Options

include/configs/ls1046a_common.h

@@ -176,23 +176,23 @@
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 18432(0x4800).
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x820)
+#define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x4800)
 #elif defined(CONFIG_QSPI_BOOT)
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_FMAN_FW_ADDR		0x40300000
+#define CONFIG_SYS_FMAN_FW_ADDR		0x40900000
 #define CONFIG_ENV_SPI_BUS		0
 #define CONFIG_ENV_SPI_CS		0
 #define CONFIG_ENV_SPI_MAX_HZ		1000000
 #define CONFIG_ENV_SPI_MODE		0x03
 #elif defined(CONFIG_NAND_BOOT)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_FMAN_FW_ADDR		(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR		(72 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_FMAN_FW_ADDR		0x60300000
+#define CONFIG_SYS_FMAN_FW_ADDR		0x60900000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

include/configs/ls1046aqds.h

@@ -12,7 +12,7 @@
 #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
 #define CONFIG_SYS_TEXT_BASE		0x82000000
 #elif defined(CONFIG_QSPI_BOOT)
-#define CONFIG_SYS_TEXT_BASE		0x40010000
+#define CONFIG_SYS_TEXT_BASE		0x40100000
 #else
 #define CONFIG_SYS_TEXT_BASE		0x60100000
 #endif
@@ -447,20 +447,20 @@ unsigned long get_board_ddr_clk(void);
 #ifdef CONFIG_NAND_BOOT
 #define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_OFFSET		(24 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SD_BOOT)
-#define CONFIG_ENV_OFFSET		(1024 * 1024)
+#define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV		0
 #define CONFIG_ENV_SIZE			0x2000
 #elif defined(CONFIG_QSPI_BOOT)
 #define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
-#define CONFIG_ENV_OFFSET		0x100000        /* 1MB */
+#define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
 #define CONFIG_ENV_SECT_SIZE		0x10000
 #else
 #define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
 #define CONFIG_ENV_SECT_SIZE		0x20000
 #define CONFIG_ENV_SIZE			0x20000
 #endif

include/configs/ls1046ardb.h

@@ -169,12 +169,12 @@
 #if defined(CONFIG_SD_BOOT)
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV		0
-#define CONFIG_ENV_OFFSET		(1024 * 1024)
+#define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
 #define CONFIG_ENV_SIZE			0x2000
 #else
 #define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SIZE			0x2000		/* 8KB */
-#define CONFIG_ENV_OFFSET		0x200000	/* 2MB */
+#define CONFIG_ENV_OFFSET		0x300000	/* 3MB */
 #define CONFIG_ENV_SECT_SIZE		0x40000		/* 256KB */
 #endif