mtd: nand: Add mvebu (PXA / AXP / A38x) NAND device driver

Cloned from the Linux driver v4.2.0-rc2. Plus some patches from
Antoine Tenart enabling controller initialization and ONFI timing
support:

http://lists.infradead.org/pipermail/linux-mtd/2015-July/060197.html

Please note that this driver needs the Linux NAND subsystem sync to v4.1
from Scott to be applied:

https://www.mail-archive.com/u-boot@lists.denx.de/msg175762.html

Otherwise it will not compile.

Tested on the Marvell Armada XP DB-MV784MP-GP eval board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Ezeguil Garcia <ezequiel.garcia@free-electrons.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>

drivers/mtd/nand/Kconfig

@@ -56,6 +56,13 @@ config SYS_NAND_VF610_NFC_60_ECC_BYTES
 
 endchoice
 
+config NAND_PXA3XX
+	bool "Support for NAND on PXA3xx and Armada 370/XP/38x"
+	select SYS_NAND_SELF_INIT
+	help
+	  This enables the driver for the NAND flash device found on
+	  PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
+
 comment "Generic NAND options"
 
 # Enhance depends when converting drivers to Kconfig which use this config

drivers/mtd/nand/Makefile

@@ -62,6 +62,7 @@ obj-$(CONFIG_NAND_MXC) += mxc_nand.o
 obj-$(CONFIG_NAND_MXS) += mxs_nand.o
 obj-$(CONFIG_NAND_NDFC) += ndfc.o
 obj-$(CONFIG_NAND_NOMADIK) += nomadik.o
+obj-$(CONFIG_NAND_PXA3XX) += pxa3xx_nand.o
 obj-$(CONFIG_NAND_S3C2410) += s3c2410_nand.o
 obj-$(CONFIG_NAND_SPEAR) += spr_nand.o
 obj-$(CONFIG_TEGRA_NAND) += tegra_nand.o

drivers/mtd/nand/pxa3xx_nand.h

@@ -0,0 +1,64 @@
+#ifndef __ASM_ARCH_PXA3XX_NAND_H
+#define __ASM_ARCH_PXA3XX_NAND_H
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+struct pxa3xx_nand_timing {
+	unsigned int	tCH;  /* Enable signal hold time */
+	unsigned int	tCS;  /* Enable signal setup time */
+	unsigned int	tWH;  /* ND_nWE high duration */
+	unsigned int	tWP;  /* ND_nWE pulse time */
+	unsigned int	tRH;  /* ND_nRE high duration */
+	unsigned int	tRP;  /* ND_nRE pulse width */
+	unsigned int	tR;   /* ND_nWE high to ND_nRE low for read */
+	unsigned int	tWHR; /* ND_nWE high to ND_nRE low for status read */
+	unsigned int	tAR;  /* ND_ALE low to ND_nRE low delay */
+};
+
+struct pxa3xx_nand_flash {
+	uint32_t	chip_id;
+	unsigned int	flash_width;    /* Width of Flash memory (DWIDTH_M) */
+	unsigned int	dfc_width;      /* Width of flash controller(DWIDTH_C) */
+	struct pxa3xx_nand_timing *timing; /* NAND Flash timing */
+};
+
+/*
+ * Current pxa3xx_nand controller has two chip select which
+ * both be workable.
+ *
+ * Notice should be taken that:
+ * When you want to use this feature, you should not enable the
+ * keep configuration feature, for two chip select could be
+ * attached with different nand chip. The different page size
+ * and timing requirement make the keep configuration impossible.
+ */
+
+/* The max num of chip select current support */
+#define NUM_CHIP_SELECT		(2)
+struct pxa3xx_nand_platform_data {
+	/* the data flash bus is shared between the Static Memory
+	 * Controller and the Data Flash Controller,  the arbiter
+	 * controls the ownership of the bus
+	 */
+	int	enable_arbiter;
+
+	/* allow platform code to keep OBM/bootloader defined NFC config */
+	int	keep_config;
+
+	/* indicate how many chip selects will be used */
+	int	num_cs;
+
+	/* use an flash-based bad block table */
+	bool	flash_bbt;
+
+	/* requested ECC strength and ECC step size */
+	int ecc_strength, ecc_step_size;
+
+	const struct mtd_partition		*parts[NUM_CHIP_SELECT];
+	unsigned int				nr_parts[NUM_CHIP_SELECT];
+
+	const struct pxa3xx_nand_flash		*flash;
+	size_t					num_flash;
+};
+#endif /* __ASM_ARCH_PXA3XX_NAND_H */