ARM: dts: stm32mp1: Add usb gadget support for stm32mp157c-ev1 board

Add DT nodes to enable DWC2 gadget support

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

arch/arm/dts/stm32mp157-pinctrl.dtsi

@@ -321,6 +321,12 @@
 					bias-disable;
 				};
 			};
+
+			usbotg_hs_pins_a: usbotg_hs-0 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */
+				};
+			};
 		};
 
 		pinctrl_z: pin-controller-z@54004000 {

arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi

@@ -25,6 +25,10 @@
 	regulator-always-on;
 };
 
+&usbotg_hs {
+	g-tx-fifo-size = <576>;
+};
+
 /* SPL part **************************************/
 &qspi {
 	u-boot,dm-spl;
@@ -60,3 +64,4 @@
 &flash0 {
 	u-boot,dm-spl;
 };
+

arch/arm/dts/stm32mp157c-ev1.dts

@@ -96,6 +96,14 @@
 	};
 };
 
+&usbotg_hs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
 &usbphyc {
 	status = "okay";
 };

arch/arm/dts/stm32mp157c.dtsi

@@ -106,6 +106,26 @@
 		};
 	};
 
+	pm_domain {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "st,stm32mp157c-pd";
+
+		pd_core_ret: core-ret-power-domain@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			#power-domain-cells = <0>;
+			label = "CORE-RETENTION";
+
+			pd_core: core-power-domain@2 {
+				reg = <2>;
+				#power-domain-cells = <0>;
+				label = "CORE";
+			};
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -654,6 +674,22 @@
 			status = "disabled";
 		};
 
+		usbotg_hs: usb-otg@49000000 {
+			compatible = "st,stm32mp1-hsotg", "snps,dwc2";
+			reg = <0x49000000 0x10000>;
+			clocks = <&rcc USBO_K>;
+			clock-names = "otg";
+			resets = <&rcc USBO_R>;
+			reset-names = "dwc2";
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			g-rx-fifo-size = <256>;
+			g-np-tx-fifo-size = <32>;
+			g-tx-fifo-size = <128 128 64 64 64 64 32 32>;
+			dr_mode = "otg";
+			power-domains = <&pd_core>;
+			status = "disabled";
+		};
+
 		rcc: rcc@50000000 {
 			compatible = "st,stm32mp1-rcc", "syscon";
 			reg = <0x50000000 0x1000>;