include/configs: Use new CONFIG_CMD_* in various n* named board config files.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

include/configs/netstar.h

@@ -140,43 +140,31 @@
 #define MTDIDS_DEFAULT		"nor0=omapflash.0,nand0=omapnand.0"
 #define MTDPARTS_DEFAULT	"mtdparts=omapflash.0:8k@16k(env),8k(r_env),448k@576k(u-boot);omapnand.0:48M(rootfs0),48M(rootfs1),-(data)"
 
-#if 0
-#define CONFIG_COMMANDS		(CFG_CMD_BDI    | \
-				 CFG_CMD_BOOTD  | \
-				 CFG_CMD_DHCP   | \
-				 CFG_CMD_ENV	| \
-				 CFG_CMD_FLASH  | \
-				 CFG_CMD_IMI    | \
-				 CFG_CMD_LOADB  | \
-				 CFG_CMD_NET    | \
-				 CFG_CMD_MEMORY | \
-				 CFG_CMD_PING   | \
-				 CFG_CMD_RUN)
 
-#else
-#define CONFIG_COMMANDS		(CFG_CMD_BDI    | \
-				 CFG_CMD_BOOTD  | \
-				 CFG_CMD_DHCP   | \
-				 CFG_CMD_ENV	| \
-				 CFG_CMD_FLASH  | \
-				 CFG_CMD_NAND	| \
-				 CFG_CMD_IMI    | \
-				 CFG_CMD_JFFS2	| \
-				 CFG_CMD_LOADB  | \
-				 CFG_CMD_NET    | \
-				 CFG_CMD_MEMORY | \
-				 CFG_CMD_PING   | \
-				 CFG_CMD_RUN)
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+
 
 #define CONFIG_JFFS2_NAND	1	/* jffs2 on nand support */
-#endif
 
 #define CONFIG_BOOTP_MASK	CONFIG_BOOTP_DEFAULT
 #define CONFIG_LOOPW
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
 #define CONFIG_BOOTDELAY	3
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* allow to break in always */
 #undef  CONFIG_BOOTARGS		/* the boot command will set bootargs*/

include/configs/ns9750dev.h

@@ -69,33 +69,19 @@
 
 #define CONFIG_BAUDRATE		38400
 
-/***********************************************************
- * Command definition
- ***********************************************************/
-#if 0 /* @TODO */
-#define CONFIG_COMMANDS \
-			(CONFIG_CMD_DFL	 | \
-			CFG_CMD_CACHE	 | \
-			/*CFG_CMD_NAND	 |*/ \
-			/*CFG_CMD_EEPROM |*/ \
-			/*CFG_CMD_I2C	 |*/ \
-			/*CFG_CMD_USB	 |*/ \
-			CFG_CMD_REGINFO  | \
-			CFG_CMD_DATE	 | \
-			CFG_CMD_ELF)
-#else
-#define CONFIG_COMMANDS \
-			(CONFIG_CMD_BDI | \
-			CFG_CMD_NET | \
-			CFG_CMD_PING	 | \
-			CFG_CMD_CONSOLE	 | \
-			CFG_CMD_LOADB	 | \
-			CFG_CMD_LOADS	 | \
-			CFG_CMD_MEMORY)
-#endif
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+
 
 #define CONFIG_BOOTDELAY	3
 /*#define CONFIG_BOOTARGS    	"root=ramfs devfs=mount console=ttySA0,9600" */
@@ -108,7 +94,7 @@
 /*#define CONFIG_BOOTFILE	"elinos-lart" */
 /*#define CONFIG_BOOTCOMMAND	"tftp; bootm" */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	115200		/* speed to run kgdb serial port */
 /* what's this ? it's not used anywhere */
 #define CONFIG_KGDB_SER_INDEX	1		/* which serial port to use */