arm: mvebu: clearfog: use the microsom .dtsi

Use hardware description from the recently introduced microsom .dtsi
file to reduce duplication.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>

arch/arm/dts/armada-388-clearfog.dts

@@ -50,6 +50,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
 #include "armada-388.dtsi"
+#include "armada-38x-solidrun-microsom.dtsi"
 
 / {
 	model = "SolidRun Clearfog A1";
@@ -70,11 +71,6 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x10000000>; /* 256 MB */
-	};
-
 	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "3P3V";
@@ -84,11 +80,6 @@
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
-			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
-			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
-			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
-
 		internal-regs {
 			ethernet@30000 {
 				mac-address = [00 50 43 02 02 02];
@@ -108,15 +99,6 @@
 				status = "okay";
 			};
 
-			ethernet@70000 {
-				mac-address = [00 50 43 02 02 01];
-				pinctrl-0 = <&ge0_rgmii_pins>;
-				pinctrl-names = "default";
-				phy = <&phy_dedicated>;
-				phy-mode = "rgmii-id";
-				status = "okay";
-			};
-
 			i2c@11000 {
 				/* Is there anything on this? */
 				clock-frequency = <100000>;
@@ -226,22 +208,6 @@
 				status = "okay";
 			};
 
-			mdio@72004 {
-				pinctrl-0 = <&mdio_pins>;
-				pinctrl-names = "default";
-
-				phy_dedicated: ethernet-phy@0 {
-					/*
-					 * Annoyingly, the marvell phy driver
-					 * configures the LED register, rather
-					 * than preserving reset-loaded setting.
-					 * We undo that rubbish here.
-					 */
-					marvell,reg-init = <3 16 0 0x101e>;
-					reg = <0>;
-				};
-			};
-
 			pinctrl@18000 {
 				clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins {
 					marvell,pins = "mpp46";
@@ -260,12 +226,6 @@
 					marvell,pins = "mpp20";
 					marvell,function = "gpio";
 				};
-				clearfog_sdhci_pins: clearfog-sdhci-pins {
-					marvell,pins = "mpp21", "mpp28",
-						       "mpp37", "mpp38",
-						       "mpp39", "mpp40";
-					marvell,function = "sd0";
-				};
 				clearfog_spi1_cs_pins: spi1-cs-pins {
 					marvell,pins = "mpp55";
 					marvell,function = "spi1";
@@ -311,7 +271,7 @@
 				bus-width = <4>;
 				cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
 				no-1-8-v;
-				pinctrl-0 = <&clearfog_sdhci_pins
+				pinctrl-0 = <&microsom_sdhci_pins
 					     &clearfog_sdhci_cd_pins>;
 				pinctrl-names = "default";
 				status = "okay";
@@ -319,13 +279,6 @@
 				wp-inverted;
 			};
 
-			serial@12000 {
-				pinctrl-0 = <&uart0_pins>;
-				pinctrl-names = "default";
-				status = "okay";
-				u-boot,dm-pre-reloc;
-			};
-
 			serial@12100 {
 				/* mikrobus uart */
 				pinctrl-0 = <&mikro_uart_pins>;
@@ -342,14 +295,6 @@
 				pinctrl-0 = <&spi1_pins &clearfog_spi1_cs_pins &mikro_spi_pins>;
 				pinctrl-names = "default";
 				status = "okay";
-
-				spi-flash@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					compatible = "w25q32", "jedec,spi-nor", "spi-flash";
-					reg = <0>; /* Chip select 0 */
-					spi-max-frequency = <3000000>;
-				};
 			};
 
 			usb3@f8000 {
@@ -457,6 +402,10 @@
 	};
 };
 
+&w25q32 {
+	status = "okay";
+};
+
 /*
 +#define A38x_CUSTOMER_BOARD_1_MPP16_23         0x00400011
 MPP18: gpio		? (pca9655 int?)