ARM: kirkwood: add SBx81LIFXCAT board

This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>

arch/arm/dts/kirkwood-atl-sbx81lifxcat.dts

@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-98dx4122.dtsi"
+
+/ {
+	model = "Allied Telesis SBx81LIFXCAT Board";
+	compatible = "atl,SBx8LIFXCAT", "marvell,kirkwood-98DX4122",
+		     "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>; /* 128 MB */
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	aliases {
+		ethernet0 = &eth0;
+		i2c0 = &i2c0;
+		spi0 = &spi0;
+	};
+
+	dsa {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+		dsa,ethernet = <&eth0>;
+		dsa,mii-bus = <&mdio>;
+		status = "okay";
+
+		switch@0 {
+			#address-cells =  <1>;
+			#size-cells = <0>;
+			reg = <1 0>;
+
+			port@0 {
+				reg = <0>;
+				label = "internal0";
+			};
+			port@1 {
+				reg = <1>;
+				label = "internal1";
+			};
+			port@8 {
+				reg = <8>;
+				label = "internal8";
+				phy-mode = "rgmii-id";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+			port@9 {
+				reg = <9>;
+				label = "internal9";
+				phy-mode = "rgmii-id";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+			port@10 {
+				reg = <10>;
+				label = "cpu";
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		ledn {
+			label = "status:ledn";
+			gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		ledp {
+			label = "status:ledp";
+			gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p128", "jedec,spi-nor", "spi-flash";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		mode = <0>;
+
+		partition@u-boot {
+			reg = <0x00000000 0x00c00000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x00c00000 0x00040000>;
+			label = "u-boot-env";
+		};
+		partition@unused {
+			reg = <0x00100000 0x00f00000>;
+			label = "unused";
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@52 {
+		compatible = "atmel,24c04";
+		reg = <0x52>;
+	};
+
+	gpio3: gpio@76 {
+		#gpio-cells = <2>;
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+};
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};

arch/arm/mach-kirkwood/Kconfig

@@ -62,6 +62,9 @@ config TARGET_NSA310S
 config TARGET_SBx81LIFKW
 	bool "Allied Telesis SBx81GS24/SBx81GT40/SBx81XS6/SBx81XS16"
 
+config TARGET_SBx81LIFXCAT
+	bool "Allied Telesis SBx81GP24/SBx81GT24"
+
 endchoice
 
 config SYS_SOC
@@ -85,5 +88,6 @@ source "board/Seagate/goflexhome/Kconfig"
 source "board/Seagate/nas220/Kconfig"
 source "board/zyxel/nsa310s/Kconfig"
 source "board/alliedtelesis/SBx81LIFKW/Kconfig"
+source "board/alliedtelesis/SBx81LIFXCAT/Kconfig"
 
 endif

board/alliedtelesis/SBx81LIFXCAT/Kconfig

@@ -0,0 +1,12 @@
+if TARGET_SBx81LIFXCAT
+
+config SYS_BOARD
+       default "SBx81LIFXCAT"
+
+config SYS_VENDOR
+       default "alliedtelesis"
+
+config SYS_CONFIG_NAME
+       default "SBx81LIFXCAT"
+
+endif

board/alliedtelesis/SBx81LIFXCAT/MAINTAINERS

@@ -0,0 +1,7 @@
+SBx81LIFXCAT BOARD
+M:	Chris Packham <chris.packham@alliedtelesis.co.nz>
+S:	Maintained
+F:	board/alliedtelesis/SBx81LIFXCAT/
+F:	include/configs/SBx81LIFXCAT
+F:	configs/SBx81LIFXCAT_defconfig
+F:	arch/arm/dts/kirkwood-atl-sbx81lifxcat.dts

board/alliedtelesis/SBx81LIFXCAT/Makefile

@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2010, 2018
+# Allied Telesis <www.alliedtelesis.com>
+#
+
+obj-y	+= sbx81lifxcat.o

board/alliedtelesis/SBx81LIFXCAT/kwbimage.cfg

@@ -0,0 +1,49 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2018 Allied Telesis
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM	spi	# Boot from SPI flash
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+DATA 0xffd100e0 0x1b1b1b1b
+DATA 0xffd20134 0xffffffff
+DATA 0xffd20138 0x009fffff
+DATA 0xffd20154 0x00000000
+DATA 0xffd2014c 0x00000000
+DATA 0xffd20148 0x00000001
+
+# Dram initalization for 1 x x16
+#  DDR II Micron part number MT47H64M16HR-3
+#  MClk 333MHz, Size 128MB, ECC disable
+#
+DATA 0xffd01400 0x43000618
+DATA 0xffd01404 0x38543000
+DATA 0xffd01408 0x23125441
+DATA 0xffd0140c 0x00000832
+DATA 0xffd01410 0x0000000D
+DATA 0xffd01414 0x00000000
+DATA 0xffd01418 0x00000000
+DATA 0xffd0141c 0x00000652
+DATA 0xffd01420 0x00000042
+DATA 0xffd01424 0x0000F0FF
+DATA 0xffd01428 0x00074410
+DATA 0xffd0147C 0x00007441
+DATA 0xffd01500 0x00000000	# SDRAM CS[0] Base address at 0x00000000
+DATA 0xffd01504 0x07FFFFF1	# SDRAM CS[0] Size 128MiB
+DATA 0xffd01508 0x10000000
+DATA 0xffd0150c 0x00FFFFF4	# SDRAM CS[1] Size, window disabled
+DATA 0xffd01514 0x00FFFFF8	# SDRAM CS[2] Size, window disabled
+DATA 0xffd0151c 0x00FFFFFC	# SDRAM CS[3] Size, window disabled
+DATA 0xffd01494 0x84210000
+DATA 0xffd01498 0x00000000
+DATA 0xffd0149c 0x0000F80F
+DATA 0xffd01480 0x00000001
+
+# End of Header extension
+DATA 0x0 0x0

board/alliedtelesis/SBx81LIFXCAT/sbx81lifxcat.c

@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2010, 2018
+ * Allied Telesis <www.alliedtelesis.com>
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <led.h>
+#include <linux/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/gpio.h>
+
+#define SBX81LIFXCAT_OE_LOW		(~0)
+#define SBX81LIFXCAT_OE_HIGH		(~BIT(11))
+#define SBX81LIFXCAT_OE_VAL_LOW		(0)
+#define SBX81LIFXCAT_OE_VAL_HIGH	(BIT(11))
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	/*
+	 * default gpio configuration
+	 * There are maximum 64 gpios controlled through 2 sets of registers
+	 * the  below configuration configures mainly initial LED status
+	 */
+	mvebu_config_gpio(SBX81LIFXCAT_OE_VAL_LOW,
+			  SBX81LIFXCAT_OE_VAL_HIGH,
+			  SBX81LIFXCAT_OE_LOW, SBX81LIFXCAT_OE_HIGH);
+
+	/* Multi-Purpose Pins Functionality configuration */
+	static const u32 kwmpp_config[] = {
+		MPP0_SPI_SCn,
+		MPP1_SPI_MOSI,
+		MPP2_SPI_SCK,
+		MPP3_SPI_MISO,
+		MPP4_NF_IO6,
+		MPP5_NF_IO7,
+		MPP6_SYSRST_OUTn,
+		MPP7_GPO,
+		MPP8_TW_SDA,
+		MPP9_TW_SCK,
+		MPP10_UART0_TXD,
+		MPP11_UART0_RXD,
+		MPP12_GPO,
+		MPP13_UART1_TXD,
+		MPP14_UART1_RXD,
+		MPP15_GPIO,
+		MPP16_GPIO,
+		MPP17_GPIO,
+		MPP18_NF_IO0,
+		MPP19_NF_IO1,
+		MPP20_GE1_0,
+		MPP21_GE1_1,
+		MPP22_GE1_2,
+		MPP23_GE1_3,
+		MPP24_GE1_4,
+		MPP25_GE1_5,
+		MPP26_GE1_6,
+		MPP27_GE1_7,
+		MPP28_GE1_8,
+		MPP29_GE1_9,
+		MPP30_GE1_10,
+		MPP31_GE1_11,
+		MPP32_GE1_12,
+		MPP33_GE1_13,
+		MPP34_GPIO,
+		MPP35_GPIO,
+		MPP36_GPIO,
+		MPP37_GPIO,
+		MPP38_GPIO,
+		MPP39_GPIO,
+		MPP40_GPIO,
+		MPP41_GPIO,
+		MPP42_GPIO,
+		MPP43_GPIO,
+		MPP44_GPIO,
+		MPP45_GPIO,
+		MPP46_GPIO,
+		MPP47_GPIO,
+		MPP48_GPIO,
+		MPP49_GPIO,
+		0
+	};
+
+	kirkwood_mpp_conf(kwmpp_config, NULL);
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* automatically defined by kirkwood config.h */
+void reset_phy(void)
+{
+}
+#endif
+
+#ifdef CONFIG_MV88E61XX_SWITCH
+int mv88e61xx_hw_reset(struct phy_device *phydev)
+{
+	phydev->advertising = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full;
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+	struct udevice *dev;
+	int ret;
+
+	ret = led_get_by_label("status:ledp", &dev);
+	if (!ret)
+		led_set_state(dev, LEDST_ON);
+
+	ret = led_get_by_label("status:ledn", &dev);
+	if (!ret)
+		led_set_state(dev, LEDST_OFF);
+
+	return 0;
+}
+#endif

configs/SBx81LIFXCAT_defconfig

@@ -0,0 +1,44 @@
+CONFIG_ARM=y
+CONFIG_KIRKWOOD=y
+CONFIG_SYS_TEXT_BASE=0x00600000
+CONFIG_TARGET_SBx81LIFXCAT=y
+CONFIG_IDENT_STRING="\nSBx81LIFXCAT"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-atl-sbx81lifxcat"
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_BOOTDELAY=3
+CONFIG_SILENT_CONSOLE=y
+CONFIG_SILENT_U_BOOT_ONLY=y
+CONFIG_HUSH_PARSER=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_DHCP=y
+CONFIG_BOOTP_NTPSERVER=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SNTP=y
+# CONFIG_CMD_LED is not set
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_DM=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+# CONFIG_MMC is not set
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHYLIB=y
+CONFIG_MV88E61XX_SWITCH=y
+CONFIG_MV88E61XX_CPU_PORT=10
+CONFIG_MV88E61XX_PHY_PORTS=0x003
+CONFIG_MV88E61XX_FIXED_PORTS=0x300
+CONFIG_MV88E61XX_RGMII_DELAY=y
+CONFIG_SPI=y
+CONFIG_KIRKWOOD_SPI=y

include/configs/SBx81LIFXCAT.h

@@ -0,0 +1,114 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
+ */
+
+#ifndef _CONFIG_SBX81LIFXCAT_H
+#define _CONFIG_SBX81LIFXCAT_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131	1	/* CPU Core subversion */
+#define CONFIG_KW88F6281	1	/* SOC Name */
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
+#define CONFIG_SYS_KWD_CONFIG	$(CONFIG_BOARDDIR)/kwbimage.cfg
+#define CONFIG_BUILD_TARGET	"u-boot.kwb"
+
+/* additions for new ARM relocation support */
+#define CONFIG_SYS_SDRAM_BASE	0x00000000
+
+#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_PCIE_INIT	/* Enable PCIE Port0 */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_GPIO	1
+
+#define CONFIG_MISC_INIT_R		/* call misc_init_r */
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1		KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX	1	/*Console on UART0 */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG	1	/* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1	/* enable memory tag */
+
+#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
+#define MTDPARTS_MTDOOPS "errlog"
+#define CONFIG_DOS_PARTITION
+
+/*
+ *  Environment variables configurations
+ */
+#define CONFIG_ENV_SPI_BUS		0
+#define CONFIG_ENV_SPI_CS		0
+#define CONFIG_ENV_SPI_MAX_HZ		20000000	/* 20Mhz */
+#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SECT_SIZE		0x40000		/* 256K */
+#define CONFIG_ENV_SIZE			0x02000
+#define CONFIG_ENV_OFFSET		0xc0000		/* env starts here - 768K */
+
+/*
+ * U-Boot bootcode configuration
+ */
+
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for monitor */
+#define CONFIG_SYS_MALLOC_LEN		  (4 << 20)	/* Reserve 4.0 MB for malloc */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Mem map for Linux*/
+
+/* size in bytes reserved for initial data */
+
+#include <asm/arch/config.h>
+/* There is no PHY directly connected so don't ask it for link status */
+#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
+#define CONFIG_NR_DRAM_BANKS	4
+#define CONFIG_SYS_MEMTEST_START 0x00400000	/* 4M */
+#define CONFIG_SYS_MEMTEST_END	0x007fffff	/*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE	/* include NetConsole support */
+#define CONFIG_NET_MULTI	/* specify more that one ports available */
+#define CONFIG_MII		/* expose smi over miiphy interface */
+#define CONFIG_MVGBE	/* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable a single port */
+#define CONFIG_PHY_BASE_ADR	0x01
+#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
+#endif /* CONFIG_CMD_NET */
+
+#define CONFIG_SYS_LOAD_ADDR  0x1000000      /* default location for tftp and bootm */
+
+#endif /* _CONFIG_SBX81LIFXCAT_H */