Armada100: Enable Ethernet support for GplugD

This patch enables ethernet support for Marvell GplugD board. Network
related commands works.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>

arch/arm/include/asm/arch-armada100/armada100.h

@@ -41,6 +41,10 @@
 /* Functional Clock Selection Mask */
 #define APBC_FNCLKSEL(x)        (((x) & 0xf) << 4)
 
+/* Fast Ethernet Controller Clock register definition */
+#define FE_CLK_RST		0x1
+#define FE_CLK_ENA		0x8
+
 /* Register Base Addresses */
 #define ARMD1_DRAM_BASE		0xB0000000
 #define ARMD1_FEC_BASE		0xC0800000
@@ -85,6 +89,59 @@ struct armd1mpmu_registers {
 };
 
 /*
+ * Application Subsystem Power Management
+ * Refer Datasheet Appendix A.9
+ */
+struct armd1apmu_registers {
+	u32 pcr;		/* 0x000 */
+	u32 ccr;		/* 0x004 */
+	u32 pad1;
+	u32 ccsr;		/* 0x00C */
+	u32 fc_timer;		/* 0x010 */
+	u32 pad2;
+	u32 ideal_cfg;		/* 0x018 */
+	u8 pad3[0x04C - 0x018 - 4];
+	u32 lcdcrc;		/* 0x04C */
+	u32 cciccrc;		/* 0x050 */
+	u32 sd1crc;		/* 0x054 */
+	u32 sd2crc;		/* 0x058 */
+	u32 usbcrc;		/* 0x05C */
+	u32 nfccrc;		/* 0x060 */
+	u32 dmacrc;		/* 0x064 */
+	u32 pad4;
+	u32 buscrc;		/* 0x06C */
+	u8 pad5[0x07C - 0x06C - 4];
+	u32 wake_clr;		/* 0x07C */
+	u8 pad6[0x090 - 0x07C - 4];
+	u32 core_status;	/* 0x090 */
+	u32 rfsc;		/* 0x094 */
+	u32 imr;		/* 0x098 */
+	u32 irwc;		/* 0x09C */
+	u32 isr;		/* 0x0A0 */
+	u8 pad7[0x0B0 - 0x0A0 - 4];
+	u32 mhst;		/* 0x0B0 */
+	u32 msr;		/* 0x0B4 */
+	u8 pad8[0x0C0 - 0x0B4 - 4];
+	u32 msst;		/* 0x0C0 */
+	u32 pllss;		/* 0x0C4 */
+	u32 smb;		/* 0x0C8 */
+	u32 gccrc;		/* 0x0CC */
+	u8 pad9[0x0D4 - 0x0CC - 4];
+	u32 smccrc;		/* 0x0D4 */
+	u32 pad10;
+	u32 xdcrc;		/* 0x0DC */
+	u32 sd3crc;		/* 0x0E0 */
+	u32 sd4crc;		/* 0x0E4 */
+	u8 pad11[0x0F0 - 0x0E4 - 4];
+	u32 cfcrc;		/* 0x0F0 */
+	u32 mspcrc;		/* 0x0F4 */
+	u32 cmucrc;		/* 0x0F8 */
+	u32 fecrc;		/* 0x0FC */
+	u32 pciecrc;		/* 0x100 */
+	u32 epdcrc;		/* 0x104 */
+};
+
+/*
  * APB1 Clock Reset/Control Registers
  * Refer Datasheet Appendix A.10
  */

arch/arm/include/asm/arch-armada100/mfp.h

@@ -64,6 +64,25 @@
 #define MFP105_CI2C_SDA		(MFP_REG(0x1a4) | MFP_AF1 | MFP_DRIVE_MEDIUM)
 #define MFP106_CI2C_SCL		(MFP_REG(0x1a8) | MFP_AF1 | MFP_DRIVE_MEDIUM)
 
+/* Fast Ethernet */
+#define MFP086_ETH_TXCLK	(MFP_REG(0x158) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP087_ETH_TXEN		(MFP_REG(0x15C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP088_ETH_TXDQ3	(MFP_REG(0x160) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP089_ETH_TXDQ2	(MFP_REG(0x164) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP090_ETH_TXDQ1	(MFP_REG(0x168) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP091_ETH_TXDQ0	(MFP_REG(0x16C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP092_ETH_CRS		(MFP_REG(0x170) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP093_ETH_COL		(MFP_REG(0x174) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP094_ETH_RXCLK	(MFP_REG(0x178) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP095_ETH_RXER		(MFP_REG(0x17C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP096_ETH_RXDQ3	(MFP_REG(0x180) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP097_ETH_RXDQ2	(MFP_REG(0x184) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP098_ETH_RXDQ1	(MFP_REG(0x188) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP099_ETH_RXDQ0	(MFP_REG(0x18C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP100_ETH_MDC		(MFP_REG(0x190) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP101_ETH_MDIO		(MFP_REG(0x194) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP103_ETH_RXDV		(MFP_REG(0x19C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+
 /* More macros can be defined here... */
 
 #define MFP_PIN_MAX	117

board/Marvell/gplugd/gplugd.c

@@ -33,6 +33,11 @@
 #include <asm/arch/mfp.h>
 #include <asm/arch/armada100.h>
 
+#ifdef CONFIG_ARMADA100_FEC
+#include <net.h>
+#include <netdev.h>
+#endif /* CONFIG_ARMADA100_FEC */
+
 DECLARE_GLOBAL_DATA_PTR;
 
 int board_early_init_f(void)
@@ -45,6 +50,26 @@ int board_early_init_f(void)
 		/* Enable Console on UART3 */
 		MFPO8_UART3_TXD,
 		MFPO9_UART3_RXD,
+
+		/* Ethernet PHY Interface */
+		MFP086_ETH_TXCLK,
+		MFP087_ETH_TXEN,
+		MFP088_ETH_TXDQ3,
+		MFP089_ETH_TXDQ2,
+		MFP090_ETH_TXDQ1,
+		MFP091_ETH_TXDQ0,
+		MFP092_ETH_CRS,
+		MFP093_ETH_COL,
+		MFP094_ETH_RXCLK,
+		MFP095_ETH_RXER,
+		MFP096_ETH_RXDQ3,
+		MFP097_ETH_RXDQ2,
+		MFP098_ETH_RXDQ1,
+		MFP099_ETH_RXDQ0,
+		MFP100_ETH_MDC,
+		MFP101_ETH_MDIO,
+		MFP103_ETH_RXDV,
+
 		MFP_EOC		/*End of configuration*/
 	};
 	/* configure MFP's */
@@ -60,3 +85,16 @@ int board_init(void)
 	gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100;
 	return 0;
 }
+
+#ifdef CONFIG_ARMADA100_FEC
+int board_eth_init(bd_t *bis)
+{
+	struct armd1apmu_registers *apmu_regs =
+		(struct armd1apmu_registers *)ARMD1_APMU_BASE;
+
+	/* Enable clock of ethernet controller */
+	writel(FE_CLK_RST | FE_CLK_ENA, &apmu_regs->fecrc);
+
+	return armada100_fec_register(ARMD1_FEC_BASE);
+}
+#endif /* CONFIG_ARMADA100_FEC */

include/configs/gplugd.h

@@ -62,8 +62,20 @@
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_AUTOSCRIPT
 #undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
+
+/* Disable DCACHE */
+#define CONFIG_SYS_DCACHE_OFF
+
+/* Network configuration */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_NET_MULTI
+#define CONFIG_ARMADA100_FEC
+
+/* DHCP Support */
+#define CONFIG_CMD_DHCP
+#define CONFIG_BOOTP_DHCP_REQUEST_DELAY		50000
+#endif /* CONFIG_CMD_NET */
 
 /*
  * mv-common.h should be defined after CMD configs since it used them