Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

MAINTAINERS

@@ -472,6 +472,10 @@ Ira W. Snyder <iws@ovro.caltech.edu>
 
 	P2020COME	P2020
 
+York Sun <yorksun@freescale.com>
+
+	T4240EMU	T4240
+
 Timur Tabi <timur@freescale.com>
 
 	MPC8349E-mITX	MPC8349
@@ -539,6 +543,10 @@ Detlev Zundel <dzu@denx.de>
 
 	inka4x0		MPC5200
 
+Po Liu <po.liu@freescale.com>
+
+	C29XPCIE	C29X
+
 -------------------------------------------------------------------------
 
 Unknown / orphaned boards:

README

@@ -406,13 +406,25 @@ The following options need to be configured:
 		This is the value to write into CCSR offset 0x18600
 		according to the A004510 workaround.
 
+		CONFIG_SYS_FSL_DSP_DDR_ADDR
+		This value denotes start offset of DDR memory which is
+		connected exclusively to the DSP cores.
+
 		CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
 		This value denotes start offset of M2 memory
 		which is directly connected to the DSP core.
 
+		CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
+		This value denotes start offset of M3 memory which is directly
+		connected to the DSP core.
+
 		CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
 		This value denotes start offset of DSP CCSR space.
 
+		CONFIG_SYS_FSL_DDR_EMU
+		Specify emulator support for DDR. Some DDR features such as
+		deskew training are not available.
+
 - Generic CPU options:
 		CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
 

arch/powerpc/cpu/mpc83xx/pcie.c

@@ -299,6 +299,8 @@ static void mpc83xx_pcie_init_bus(int bus, struct pci_region *reg)
 
 	printf("PCIE%d: ", bus);
 
+#define PCI_LTSSM	0x404 /* PCIe Link Training, Status State Machine */
+#define PCI_LTSSM_L0	0x16 /* L0 state */
 	reg16 = in_le16(hose_cfg_base + PCI_LTSSM);
 	if (reg16 >= PCI_LTSSM_L0)
 		printf("link\n");

arch/powerpc/cpu/mpc85xx/Makefile

@@ -46,6 +46,7 @@ COBJS-$(CONFIG_MPC8568) += ddr-gen2.o
 COBJS-$(CONFIG_MPC8544) += ddr-gen2.o
 
 # supports ddr1/2/3
+COBJS-$(CONFIG_PPC_C29X)	+= ddr-gen3.o
 COBJS-$(CONFIG_MPC8572) += ddr-gen3.o
 COBJS-$(CONFIG_MPC8536) += ddr-gen3.o
 COBJS-$(CONFIG_MPC8569)	+= ddr-gen3.o
@@ -100,6 +101,7 @@ COBJS-$(CONFIG_SYS_FSL_QORIQ_CHASSIS1) += fsl_corenet_serdes.o
 COBJS-$(CONFIG_SYS_FSL_QORIQ_CHASSIS2) += fsl_corenet2_serdes.o
 
 # SoC specific SERDES support
+COBJS-$(CONFIG_PPC_C29X)	+= c29x_serdes.o
 COBJS-$(CONFIG_MPC8536) += mpc8536_serdes.o
 COBJS-$(CONFIG_MPC8544) += mpc8544_serdes.o
 COBJS-$(CONFIG_MPC8548) += mpc8548_serdes.o

arch/powerpc/cpu/mpc85xx/b4860_ids.c

@@ -41,8 +41,8 @@ struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = {
 
 #ifdef CONFIG_SYS_SRIO
 struct srio_liodn_id_table srio_liodn_tbl[] = {
-	SET_SRIO_LIODN_1(1, 307),
-	SET_SRIO_LIODN_1(2, 387),
+	SET_SRIO_LIODN_BASE(1, 307),
+	SET_SRIO_LIODN_BASE(2, 387),
 };
 int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl);
 #endif
@@ -112,10 +112,10 @@ int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl);
 #ifdef CONFIG_SYS_DPAA_RMAN
 struct liodn_id_table rman_liodn_tbl[] = {
 	/* Set RMan block 0-3 liodn offset */
-	SET_RMAN_LIODN(0, 678),
-	SET_RMAN_LIODN(1, 679),
-	SET_RMAN_LIODN(2, 680),
-	SET_RMAN_LIODN(3, 681),
+	SET_RMAN_LIODN(0, 6),
+	SET_RMAN_LIODN(1, 7),
+	SET_RMAN_LIODN(2, 8),
+	SET_RMAN_LIODN(3, 9),
 };
 int rman_liodn_tbl_sz = ARRAY_SIZE(rman_liodn_tbl);
 #endif

arch/powerpc/cpu/mpc85xx/c29x_serdes.c

@@ -0,0 +1,62 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+#include <common.h>
+#include <asm/io.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_serdes.h>
+
+#define SRDS1_MAX_LANES		4
+
+static u32 serdes1_prtcl_map;
+
+struct serdes_config {
+	u32 protocol;
+	u8 lanes[SRDS1_MAX_LANES];
+};
+
+static const struct serdes_config serdes1_cfg_tbl[] = {
+	/* SerDes 1 */
+	{1, {PCIE1, PCIE1, PCIE1, PCIE1} },
+	{2, {PCIE1, PCIE1, PCIE1, PCIE1} },
+	{3, {PCIE1, PCIE1, NONE, NONE} },
+	{4, {PCIE1, PCIE1, NONE, NONE} },
+	{5, {PCIE1, NONE, NONE, NONE} },
+	{6, {PCIE1, NONE, NONE, NONE} },
+	{}
+};
+
+int is_serdes_configured(enum srds_prtcl device)
+{
+	return (1 << device) & serdes1_prtcl_map;
+}
+
+void fsl_serdes_init(void)
+{
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+	u32 pordevsr = in_be32(&gur->pordevsr);
+	u32 srds_cfg = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >>
+				MPC85xx_PORDEVSR_IO_SEL_SHIFT;
+	const struct serdes_config *ptr;
+	int lane;
+
+	debug("PORDEVSR[IO_SEL_SRDS] = %x\n", srds_cfg);
+
+	if (srds_cfg > ARRAY_SIZE(serdes1_cfg_tbl)) {
+		printf("Invalid PORDEVSR[IO_SEL_SRDS] = %d\n", srds_cfg);
+		return;
+	}
+
+	ptr = &serdes1_cfg_tbl[srds_cfg];
+	if (!ptr->protocol)
+		return;
+
+	for (lane = 0; lane < SRDS1_MAX_LANES; lane++) {
+		enum srds_prtcl lane_prtcl = ptr->lanes[lane];
+		serdes1_prtcl_map |= (1 << lane_prtcl);
+	}
+}

arch/powerpc/cpu/mpc85xx/cmd_errata.c

@@ -245,6 +245,9 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 #ifdef CONFIG_SYS_FSL_ERRATUM_A006593
 	puts("Work-around for Erratum A006593 enabled\n");
 #endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_A005812
+	puts("Work-around for Erratum A-005812 enabled\n");
+#endif
 	return 0;
 }
 

arch/powerpc/cpu/mpc85xx/cpu.c

@@ -44,10 +44,10 @@ int checkcpu (void)
 	uint major, minor;
 	struct cpu_type *cpu;
 	char buf1[32], buf2[32];
-#if (defined(CONFIG_DDR_CLK_FREQ) || \
-	defined(CONFIG_FSL_CORENET)) && !defined(CONFIG_SYS_FSL_QORIQ_CHASSIS2)
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-#endif /* CONFIG_FSL_CORENET */
+#if defined(CONFIG_DDR_CLK_FREQ) || defined(CONFIG_FSL_CORENET)
+	ccsr_gur_t __iomem *gur =
+		(void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+#endif
 
 	/*
 	 * Cornet platforms use ddr sync bit in RCW to indicate sync vs async
@@ -211,6 +211,21 @@ int checkcpu (void)
 
 	puts("L1:    D-cache 32 kB enabled\n       I-cache 32 kB enabled\n");
 
+#ifdef CONFIG_FSL_CORENET
+	/* Display the RCW, so that no one gets confused as to what RCW
+	 * we're actually using for this boot.
+	 */
+	puts("Reset Configuration Word (RCW):");
+	for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
+		u32 rcw = in_be32(&gur->rcwsr[i]);
+
+		if ((i % 4) == 0)
+			printf("\n       %08x:", i * 4);
+		printf(" %08x", rcw);
+	}
+	puts("\n");
+#endif
+
 	return 0;
 }
 

arch/powerpc/cpu/mpc85xx/cpu_init.c

@@ -399,6 +399,14 @@ int cpu_init_r(void)
 		sync();
 	}
 #endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_A005812
+	/*
+	 * A-005812 workaround sets bit 32 of SPR 976 for SoCs running
+	 * in write shadow mode. Checking DCWS before setting SPR 976.
+	 */
+	if (mfspr(L1CSR2) & L1CSR2_DCWS)
+		mtspr(SPRN_HDBCR0, (mfspr(SPRN_HDBCR0) | 0x80000000));
+#endif
 
 #if defined(CONFIG_PPC_SPINTABLE_COMPATIBLE) && defined(CONFIG_MP)
 	spin = getenv("spin_table_compat");
@@ -532,8 +540,10 @@ skip_l2:
 
 	enable_cpc();
 
+#ifndef CONFIG_SYS_FSL_NO_SERDES
 	/* needs to be in ram since code uses global static vars */
 	fsl_serdes_init();
+#endif
 
 #ifdef CONFIG_SYS_FSL_ERRATUM_A005871
 	if (IS_SVR_REV(svr, 1, 0)) {

arch/powerpc/cpu/mpc85xx/ddr-gen1.c

@@ -15,7 +15,7 @@
 #endif
 
 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-			     unsigned int ctrl_num)
+			     unsigned int ctrl_num, int step)
 {
 	unsigned int i;
 	volatile ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;

arch/powerpc/cpu/mpc85xx/ddr-gen2.c

@@ -16,7 +16,7 @@
 #endif
 
 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-			     unsigned int ctrl_num)
+			     unsigned int ctrl_num, int step)
 {
 	unsigned int i;
 	ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;

arch/powerpc/cpu/mpc85xx/ddr-gen3.c

@@ -15,8 +15,18 @@
 #error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
 #endif
 
+
+/*
+ * regs has the to-be-set values for DDR controller registers
+ * ctrl_num is the DDR controller number
+ * step: 0 goes through the initialization in one pass
+ *       1 sets registers and returns before enabling controller
+ *       2 resumes from step 1 and continues to initialize
+ * Dividing the initialization to two steps to deassert DDR reset signal
+ * to comply with JEDEC specs for RDIMMs.
+ */
 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-			     unsigned int ctrl_num)
+			     unsigned int ctrl_num, int step)
 {
 	unsigned int i, bus_width;
 	volatile ccsr_ddr_t *ddr;
@@ -54,6 +64,9 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 		return;
 	}
 
+	if (step == 2)
+		goto step2;
+
 	if (regs->ddr_eor)
 		out_be32(&ddr->eor, regs->ddr_eor);
 #ifdef CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134
@@ -123,10 +136,17 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 	out_be32(&ddr->timing_cfg_5, regs->timing_cfg_5);
 	out_be32(&ddr->ddr_zq_cntl, regs->ddr_zq_cntl);
 	out_be32(&ddr->ddr_wrlvl_cntl, regs->ddr_wrlvl_cntl);
+#ifndef CONFIG_SYS_FSL_DDR_EMU
+	/*
+	 * Skip these two registers if running on emulator
+	 * because emulator doesn't have skew between bytes.
+	 */
+
 	if (regs->ddr_wrlvl_cntl_2)
 		out_be32(&ddr->ddr_wrlvl_cntl_2, regs->ddr_wrlvl_cntl_2);
 	if (regs->ddr_wrlvl_cntl_3)
 		out_be32(&ddr->ddr_wrlvl_cntl_3, regs->ddr_wrlvl_cntl_3);
+#endif
 
 	out_be32(&ddr->ddr_sr_cntr, regs->ddr_sr_cntr);
 	out_be32(&ddr->ddr_sdram_rcw_1, regs->ddr_sdram_rcw_1);
@@ -150,6 +170,20 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 	out_be32(&ddr->debug[21], 0x24000000);
 #endif /* CONFIG_SYS_FSL_ERRATUM_DDR_A003474 */
 
+	/*
+	 * For RDIMMs, JEDEC spec requires clocks to be stable before reset is
+	 * deasserted. Clocks start when any chip select is enabled and clock
+	 * control register is set. Because all DDR components are connected to
+	 * one reset signal, this needs to be done in two steps. Step 1 is to
+	 * get the clocks started. Step 2 resumes after reset signal is
+	 * deasserted.
+	 */
+	if (step == 1) {
+		udelay(200);
+		return;
+	}
+
+step2:
 	/* Set, but do not enable the memory */
 	temp_sdram_cfg = regs->ddr_sdram_cfg;
 	temp_sdram_cfg &= ~(SDRAM_CFG_MEM_EN);

arch/powerpc/cpu/mpc85xx/fdt.c

@@ -604,8 +604,12 @@ void ft_cpu_setup(void *blob, bd_t *bd)
 
 	fdt_add_enet_stashing(blob);
 
+#ifndef CONFIG_FSL_TBCLK_EXTRA_DIV
+#define CONFIG_FSL_TBCLK_EXTRA_DIV 1
+#endif
 	do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
-		"timebase-frequency", get_tbclk(), 1);
+		"timebase-frequency", get_tbclk() / CONFIG_FSL_TBCLK_EXTRA_DIV,
+		1);
 	do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
 		"bus-frequency", bd->bi_busfreq, 1);
 	get_sys_info(&sysinfo);

arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.h

@@ -9,5 +9,4 @@
 
 int is_serdes_prtcl_valid(int serdes, u32 prtcl);
 int serdes_lane_enabled(int lane);
-enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane);
 #endif /* __FSL_CORENET2_SERDES_H */

arch/powerpc/cpu/mpc85xx/release.S

@@ -226,6 +226,21 @@ __secondary_start_page:
 2:
 #endif
 
+#ifdef CONFIG_SYS_FSL_ERRATUM_A005812
+	/*
+	 * A-005812 workaround sets bit 32 of SPR 976 for SoCs running in
+	 * write shadow mode. This code should run after other code setting
+	 * DCWS.
+	 */
+	mfspr	r3,L1CSR2
+	andis.	r3,r3,(L1CSR2_DCWS)@h
+	beq	1f
+	mfspr	r3, SPRN_HDBCR0
+	oris	r3, r3, 0x8000
+	mtspr	SPRN_HDBCR0, r3
+1:
+#endif
+
 #ifdef CONFIG_BACKSIDE_L2_CACHE
 	/* skip L2 setup on P2040/P2040E as they have no L2 */
 	mfspr	r3,SPRN_SVR

arch/powerpc/cpu/mpc85xx/start.S

@@ -33,7 +33,8 @@
 #define MINIMAL_SPL
 #endif
 
-#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_SECURE_BOOT)
+#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT) && \
+	!defined(CONFIG_SECURE_BOOT) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 #define NOR_BOOT
 #endif
 

arch/powerpc/cpu/mpc85xx/t4240_ids.c

@@ -65,8 +65,8 @@ struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = {
 #endif
 
 struct srio_liodn_id_table srio_liodn_tbl[] = {
-	SET_SRIO_LIODN_1(1, 307),
-	SET_SRIO_LIODN_1(2, 387),
+	SET_SRIO_LIODN_BASE(1, 307),
+	SET_SRIO_LIODN_BASE(2, 387),
 };
 int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl);
 
@@ -159,10 +159,10 @@ int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl);
 #ifdef CONFIG_SYS_DPAA_RMAN
 struct liodn_id_table rman_liodn_tbl[] = {
 	/* Set RMan block 0-3 liodn offset */
-	SET_RMAN_LIODN(0, 678),
-	SET_RMAN_LIODN(1, 679),
-	SET_RMAN_LIODN(2, 680),
-	SET_RMAN_LIODN(3, 681),
+	SET_RMAN_LIODN(0, 6),
+	SET_RMAN_LIODN(1, 7),
+	SET_RMAN_LIODN(2, 8),
+	SET_RMAN_LIODN(3, 9),
 };
 int rman_liodn_tbl_sz = ARRAY_SIZE(rman_liodn_tbl);
 #endif

arch/powerpc/cpu/mpc86xx/ddr-8641.c

@@ -15,7 +15,7 @@
 #endif
 
 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-			     unsigned int ctrl_num)
+			     unsigned int ctrl_num, int step)
 {
 	unsigned int i;
 	volatile ccsr_ddr_t *ddr;

arch/powerpc/cpu/mpc8xxx/cpu.c

@@ -79,6 +79,9 @@ static struct cpu_type cpu_type_list[] = {
 	CPU_TYPE_ENTRY(BSC9131, 9131, 1),
 	CPU_TYPE_ENTRY(BSC9132, 9132, 2),
 	CPU_TYPE_ENTRY(BSC9232, 9232, 2),
+	CPU_TYPE_ENTRY(C291, C291, 1),
+	CPU_TYPE_ENTRY(C292, C292, 1),
+	CPU_TYPE_ENTRY(C293, C293, 1),
 #elif defined(CONFIG_MPC86xx)
 	CPU_TYPE_ENTRY(8610, 8610, 1),
 	CPU_TYPE_ENTRY(8641, 8641, 2),

arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c

@@ -364,7 +364,7 @@ static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr,
 
 	ddr->timing_cfg_3 = (0
 		| ((ext_pretoact & 0x1) << 28)
-		| ((ext_acttopre & 0x2) << 24)
+		| ((ext_acttopre & 0x3) << 24)
 		| ((ext_acttorw & 0x1) << 22)
 		| ((ext_refrec & 0x1F) << 16)
 		| ((ext_caslat & 0x3) << 12)
@@ -681,6 +681,7 @@ static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr,
 	unsigned int odt_cfg = 0;	/* ODT configuration */
 	unsigned int num_pr;		/* Number of posted refreshes */
 	unsigned int slow = 0;		/* DDR will be run less than 1250 */
+	unsigned int x4_en = 0;		/* x4 DRAM enable */
 	unsigned int obc_cfg;		/* On-The-Fly Burst Chop Cfg */
 	unsigned int ap_en;		/* Address Parity Enable */
 	unsigned int d_init;		/* DRAM data initialization */
@@ -725,6 +726,8 @@ static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr,
 		ap_en = 0;
 	}
 
+	x4_en = popts->x4_en ? 1 : 0;
+
 #if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
 	/* Use the DDR controller to auto initialize memory. */
 	d_init = popts->ECC_init_using_memctl;
@@ -747,6 +750,7 @@ static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr,
 		| ((odt_cfg & 0x3) << 21)
 		| ((num_pr & 0xf) << 12)
 		| ((slow & 1) << 11)
+		| (x4_en << 10)
 		| (qd_en << 9)
 		| (unq_mrs_en << 8)
 		| ((obc_cfg & 0x1) << 6)
@@ -1585,8 +1589,8 @@ compute_fsl_memctl_config_regs(const memctl_options_t *popts,
 				| ((ea & 0xFFF) << 0)	/* ending address MSB */
 				);
 		} else {
-			debug("FSLDDR: setting bnds to 0 for inactive CS\n");
-			ddr->cs[i].bnds = 0;
+			/* setting bnds to 0xffffffff for inactive CS */
+			ddr->cs[i].bnds = 0xffffffff;
 		}
 
 		debug("FSLDDR: cs[%d]_bnds = 0x%08x\n", i, ddr->cs[i].bnds);
@@ -1638,5 +1642,10 @@ compute_fsl_memctl_config_regs(const memctl_options_t *popts,
 
 	set_ddr_sdram_rcw(ddr, popts, common_dimm);
 
+#ifdef CONFIG_SYS_FSL_DDR_EMU
+	/* disble DDR training for emulator */
+	ddr->debug[2] = 0x00000400;
+	ddr->debug[4] = 0xff800000;
+#endif
 	return check_fsl_memctl_config_regs(ddr);
 }

arch/powerpc/cpu/mpc8xxx/ddr/ddr.h

@@ -96,7 +96,7 @@ unsigned int check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr);
 
 /* processor specific function */
 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-				   unsigned int ctrl_num);
+				   unsigned int ctrl_num, int step);
 
 /* board specific function */
 int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,

arch/powerpc/cpu/mpc8xxx/ddr/ddr3_dimm_params.c

@@ -129,6 +129,7 @@ ddr_compute_dimm_parameters(const ddr3_spd_eeprom_t *spd,
 		pdimm->ec_sdram_width = 0;
 	pdimm->data_width = pdimm->primary_sdram_width
 			  + pdimm->ec_sdram_width;
+	pdimm->device_width = 1 << ((spd->organization & 0x7) + 2);
 
 	/* These are the types defined by the JEDEC DDR3 SPD spec */
 	pdimm->mirrored_dimm = 0;

arch/powerpc/cpu/mpc8xxx/ddr/interactive.c

@@ -205,6 +205,7 @@ static void fsl_ddr_dimm_parameters_edit(fsl_ddr_info_t *pinfo,
 		DIMM_PARM(primary_sdram_width),
 		DIMM_PARM(ec_sdram_width),
 		DIMM_PARM(registered_dimm),
+		DIMM_PARM(device_width),
 
 		DIMM_PARM(n_row_addr),
 		DIMM_PARM(n_col_addr),
@@ -263,6 +264,7 @@ static void print_dimm_parameters(const dimm_params_t *pdimm)
 		DIMM_PARM(primary_sdram_width),
 		DIMM_PARM(ec_sdram_width),
 		DIMM_PARM(registered_dimm),
+		DIMM_PARM(device_width),
 
 		DIMM_PARM(n_row_addr),
 		DIMM_PARM(n_col_addr),
@@ -443,6 +445,7 @@ static void fsl_ddr_options_edit(fsl_ddr_info_t *pinfo,
 		CTRL_OPTIONS(twoT_en),
 		CTRL_OPTIONS(threeT_en),
 		CTRL_OPTIONS(ap_en),
+		CTRL_OPTIONS(x4_en),
 		CTRL_OPTIONS(bstopre),
 		CTRL_OPTIONS(wrlvl_override),
 		CTRL_OPTIONS(wrlvl_sample),
@@ -687,6 +690,7 @@ static void print_memctl_options(const memctl_options_t *popts)
 		CTRL_OPTIONS(threeT_en),
 		CTRL_OPTIONS(registered_dimm_en),
 		CTRL_OPTIONS(ap_en),
+		CTRL_OPTIONS(x4_en),
 		CTRL_OPTIONS(bstopre),
 		CTRL_OPTIONS(wrlvl_override),
 		CTRL_OPTIONS(wrlvl_sample),

arch/powerpc/cpu/mpc8xxx/ddr/main.c

@@ -25,10 +25,6 @@ void fsl_ddr_set_lawbar(
 		unsigned int ctrl_num);
 void fsl_ddr_set_intl3r(const unsigned int granule_size);
 
-/* processor specific function */
-extern void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-				   unsigned int ctrl_num);
-
 #if defined(SPD_EEPROM_ADDRESS) || \
     defined(SPD_EEPROM_ADDRESS1) || defined(SPD_EEPROM_ADDRESS2) || \
     defined(SPD_EEPROM_ADDRESS3) || defined(SPD_EEPROM_ADDRESS4)
@@ -365,9 +361,11 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step,
 {
 	unsigned int i, j;
 	unsigned long long total_mem = 0;
+	int assert_reset;
 
 	fsl_ddr_cfg_regs_t *ddr_reg = pinfo->fsl_ddr_config_reg;
 	common_timing_params_t *timing_params = pinfo->common_timing_params;
+	assert_reset = board_need_mem_reset();
 
 	/* data bus width capacity adjust shift amount */
 	unsigned int dbw_capacity_adjust[CONFIG_NUM_DDR_CONTROLLERS];
@@ -462,7 +460,20 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step,
 					timing_params[i].all_DIMMs_registered,
 					&pinfo->memctl_opts[i],
 					pinfo->dimm_params[i], i);
+			/*
+			 * For RDIMMs, JEDEC spec requires clocks to be stable
+			 * before reset signal is deasserted. For the boards
+			 * using fixed parameters, this function should be
+			 * be called from board init file.
+			 */
+			if (timing_params[i].all_DIMMs_registered)
+				assert_reset = 1;
 		}
+		if (assert_reset) {
+			debug("Asserting mem reset\n");
+			board_assert_mem_reset();
+		}
+
 	case STEP_ASSIGN_ADDRESSES:
 		/* STEP 5:  Assign addresses to chip selects */
 		check_interleaving_options(pinfo);
@@ -504,7 +515,13 @@ fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step,
 				fsl_ddr_cfg_regs_t *reg = &ddr_reg[i];
 				if (reg->cs[j].config & 0x80000000) {
 					unsigned int end;
-					end = reg->cs[j].bnds & 0xFFF;
+					/*
+					 * 0xfffffff is a special value we put
+					 * for unused bnds
+					 */
+					if (reg->cs[j].bnds == 0xffffffff)
+						continue;
+					end = reg->cs[j].bnds & 0xffff;
 					if (end > max_end) {
 						max_end = end;
 					}
@@ -531,6 +548,7 @@ phys_size_t fsl_ddr_sdram(void)
 	unsigned int law_memctl = LAW_TRGT_IF_DDR_1;
 	unsigned long long total_memory;
 	fsl_ddr_info_t info;
+	int deassert_reset;
 
 	/* Reset info structure. */
 	memset(&info, 0, sizeof(fsl_ddr_info_t));
@@ -559,7 +577,21 @@ phys_size_t fsl_ddr_sdram(void)
 		}
 	}
 
-	/* Program configuration registers. */
+	/*
+	 * Program configuration registers.
+	 * JEDEC specs requires clocks to be stable before deasserting reset
+	 * for RDIMMs. Clocks start after chip select is enabled and clock
+	 * control register is set. During step 1, all controllers have their
+	 * registers set but not enabled. Step 2 proceeds after deasserting
+	 * reset through board FPGA or GPIO.
+	 * For non-registered DIMMs, initialization can go through but it is
+	 * also OK to follow the same flow.
+	 */
+	deassert_reset = board_need_mem_reset();
+	for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+		if (info.common_timing_params[i].all_DIMMs_registered)
+			deassert_reset = 1;
+	}
 	for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
 		debug("Programming controller %u\n", i);
 		if (info.common_timing_params[i].ndimms_present == 0) {
@@ -567,8 +599,22 @@ phys_size_t fsl_ddr_sdram(void)
 					"skipping programming\n", i);
 			continue;
 		}
-
-		fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), i);
+		/*
+		 * The following call with step = 1 returns before enabling
+		 * the controller. It has to finish with step = 2 later.
+		 */
+		fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), i,
+					deassert_reset ? 1 : 0);
+	}
+	if (deassert_reset) {
+		/* Use board FPGA or GPIO to deassert reset signal */
+		debug("Deasserting mem reset\n");
+		board_deassert_mem_reset();
+		for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+			/* Call with step = 2 to continue initialization */
+			fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]),
+						i, 2);
+		}
 	}
 
 	/* program LAWs */

arch/powerpc/cpu/mpc8xxx/ddr/options.c

@@ -700,6 +700,8 @@ unsigned int populate_memctl_options(int all_DIMMs_registered,
 	}
 #endif
 
+	popts->x4_en = (pdimm[0].device_width == 4) ? 1 : 0;
+
 	/* Choose burst length. */
 #if defined(CONFIG_FSL_DDR3)
 #if defined(CONFIG_E500MC)

arch/powerpc/include/asm/config_mpc85xx.h

@@ -303,6 +303,7 @@
 
 #elif defined(CONFIG_PPC_P2041) /* also supports P2040 */
 #define CONFIG_SYS_FSL_QORIQ_CHASSIS1
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MAX_CPUS			4
 #define CONFIG_SYS_FSL_NUM_CC_PLLS	2
 #define CONFIG_SYS_FSL_NUM_LAWS		32
@@ -336,6 +337,7 @@
 
 #elif defined(CONFIG_PPC_P3041)
 #define CONFIG_SYS_FSL_QORIQ_CHASSIS1
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MAX_CPUS			4
 #define CONFIG_SYS_FSL_NUM_CC_PLLS	2
 #define CONFIG_SYS_FSL_NUM_LAWS		32
@@ -366,9 +368,11 @@
 #define CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 0xf0000000
 #define CONFIG_SYS_FSL_ERRATUM_SRIO_A004034
 #define CONFIG_SYS_FSL_ERRATUM_A004849
+#define CONFIG_SYS_FSL_ERRATUM_A005812
 
 #elif defined(CONFIG_PPC_P4080) /* also supports P4040 */
 #define CONFIG_SYS_FSL_QORIQ_CHASSIS1
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MAX_CPUS			8
 #define CONFIG_SYS_FSL_NUM_CC_PLLS	4
 #define CONFIG_SYS_FSL_NUM_LAWS		32
@@ -410,10 +414,12 @@
 #define CONFIG_SYS_FSL_ERRATUM_A004849
 #define CONFIG_SYS_FSL_ERRATUM_A004580
 #define CONFIG_SYS_P4080_ERRATUM_PCIE_A003
+#define CONFIG_SYS_FSL_ERRATUM_A005812
 
 #elif defined(CONFIG_PPC_P5020) /* also supports P5010 */
 #define CONFIG_SYS_PPC64		/* 64-bit core */
 #define CONFIG_SYS_FSL_QORIQ_CHASSIS1
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MAX_CPUS			2
 #define CONFIG_SYS_FSL_NUM_CC_PLLS	2
 #define CONFIG_SYS_FSL_NUM_LAWS		32
@@ -444,6 +450,7 @@
 #elif defined(CONFIG_PPC_P5040)
 #define CONFIG_SYS_PPC64
 #define CONFIG_SYS_FSL_QORIQ_CHASSIS1
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MAX_CPUS			4
 #define CONFIG_SYS_FSL_NUM_CC_PLLS	3
 #define CONFIG_SYS_FSL_NUM_LAWS		32
@@ -469,6 +476,7 @@
 #define CONFIG_SYS_FSL_ERRATUM_A004510
 #define CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV	0x10
 #define CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 0xf0000000
+#define CONFIG_SYS_FSL_ERRATUM_A005812
 
 #elif defined(CONFIG_BSC9131)
 #define CONFIG_MAX_CPUS			1
@@ -492,6 +500,10 @@
 #define CONFIG_TSECV2
 #define CONFIG_SYS_FSL_SEC_COMPAT	4
 #define CONFIG_NUM_DDR_CONTROLLERS	2
+#define CONFIG_SYS_FSL_DSP_DDR_ADDR	0x40000000
+#define CONFIG_SYS_FSL_DSP_M2_RAM_ADDR	0xb0000000
+#define CONFIG_SYS_FSL_DSP_M3_RAM_ADDR	0xc0000000
+#define CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT	0xff600000
 #define CONFIG_SYS_FSL_IFC_BANK_COUNT	3
 #define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_NAND_FSL_IFC
@@ -536,6 +548,7 @@
 #define CONFIG_SYS_FSL_SRIO_MAX_PORTS	2
 #define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM	9
 #define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM	5
+#define CONFIG_SYS_FSL_SRIO_LIODN
 #define CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
 #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
 #define CONFIG_SYS_FSL_ERRATUM_A004468
@@ -576,6 +589,7 @@
 #define CONFIG_SYS_FSL_SRIO_MAX_PORTS	2
 #define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM	9
 #define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM	5
+#define CONFIG_SYS_FSL_SRIO_LIODN
 #else
 #define CONFIG_MAX_CPUS			2
 #define CONFIG_SYS_FSL_CORES_PER_CLUSTER 2
@@ -612,6 +626,18 @@
 #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
 #define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000
 
+#elif defined(CONFIG_PPC_C29X)
+#define CONFIG_MAX_CPUS			1
+#define CONFIG_FSL_SDHC_V2_3
+#define CONFIG_SYS_FSL_NUM_LAWS		12
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB	3
+#define CONFIG_TSECV2_1
+#define CONFIG_SYS_FSL_SEC_COMPAT	6
+#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_SYS_FSL_IFC_BANK_COUNT	8
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
+
 #else
 #error Processor type not defined for this platform
 #endif

arch/powerpc/include/asm/fsl_ddr_dimm_params.h

@@ -26,6 +26,7 @@ typedef struct dimm_params_s {
 	unsigned int primary_sdram_width;
 	unsigned int ec_sdram_width;
 	unsigned int registered_dimm;
+	unsigned int device_width;	/* x4, x8, x16 components */
 
 	/* SDRAM device parameters */
 	unsigned int n_row_addr;

arch/powerpc/include/asm/fsl_ddr_sdram.h

@@ -277,6 +277,7 @@ typedef struct memctl_options_s {
 	unsigned int mirrored_dimm;
 	unsigned int quad_rank_present;
 	unsigned int ap_en;	/* address parity enable for RDIMM */
+	unsigned int x4_en;	/* enable x4 devices */
 
 	/* Global Timing Parameters */
 	unsigned int cas_latency_override;
@@ -330,9 +331,31 @@ extern phys_size_t fsl_ddr_sdram(void);
 extern phys_size_t fsl_ddr_sdram_size(void);
 extern int fsl_use_spd(void);
 extern void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
-					unsigned int ctrl_num);
+					unsigned int ctrl_num, int step);
 u32 fsl_ddr_get_intl3r(void);
 
+static void __board_assert_mem_reset(void)
+{
+}
+
+static void __board_deassert_mem_reset(void)
+{
+}
+
+void board_assert_mem_reset(void)
+	__attribute__((weak, alias("__board_assert_mem_reset")));
+
+void board_deassert_mem_reset(void)
+	__attribute__((weak, alias("__board_deassert_mem_reset")));
+
+static int __board_need_mem_reset(void)
+{
+	return 0;
+}
+
+int board_need_mem_reset(void)
+	__attribute__((weak, alias("__board_need_mem_reset")));
+
 /*
  * The 85xx boards have a common prototype for fixed_sdram so put the
  * declaration here.

arch/powerpc/include/asm/fsl_law.h

@@ -82,7 +82,7 @@ enum law_trgt_if {
 #ifndef CONFIG_MPC8641
 	LAW_TRGT_IF_PCIE_1 = 0x02,
 #endif
-#if defined(CONFIG_BSC9131)
+#if defined(CONFIG_BSC9131) || defined(CONFIG_BSC9132)
 	LAW_TRGT_IF_OCN_DSP = 0x03,
 #else
 #if !defined(CONFIG_MPC8572) && !defined(CONFIG_P2020)
@@ -92,9 +92,14 @@ enum law_trgt_if {
 	LAW_TRGT_IF_LBC = 0x04,
 	LAW_TRGT_IF_CCSR = 0x08,
 	LAW_TRGT_IF_DSP_CCSR = 0x09,
+	LAW_TRGT_IF_PLATFORM_SRAM = 0x0a,
 	LAW_TRGT_IF_DDR_INTRLV = 0x0b,
 	LAW_TRGT_IF_RIO = 0x0c,
+#if defined(CONFIG_BSC9132)
+	LAW_TRGT_IF_CLASS_DSP = 0x0d,
+#else
 	LAW_TRGT_IF_RIO_2 = 0x0d,
+#endif
 	LAW_TRGT_IF_DPAA_SWP_SRAM = 0x0e,
 	LAW_TRGT_IF_DDR = 0x0f,
 	LAW_TRGT_IF_DDR_2 = 0x16,	/* 2nd controller */

arch/powerpc/include/asm/fsl_liodn.h

@@ -29,6 +29,13 @@ struct srio_liodn_id_table {
 		+ CONFIG_SYS_MPC85xx_GUTS_OFFSET + CONFIG_SYS_CCSRBAR, \
 	}
 
+#define SET_SRIO_LIODN_BASE(port, id_a) \
+	{ .id = { id_a }, .num_ids = 1, .portid = port, \
+	  .reg_offset[0] = offsetof(struct ccsr_rio, liodn) \
+		+ (port - 1) * 0x200 \
+		+ CONFIG_SYS_FSL_SRIO_ADDR, \
+	}
+
 struct liodn_id_table {
 	const char * compat;
 	u32 id[2];

arch/powerpc/include/asm/fsl_pci.h

@@ -1,5 +1,5 @@
 /*
- * Copyright 2007,2009-2011 Freescale Semiconductor, Inc.
+ * Copyright 2007,2009-2012 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -13,6 +13,34 @@
 
 #define PEX_IP_BLK_REV_2_2	0x02080202
 #define PEX_IP_BLK_REV_2_3	0x02080203
+#define PEX_IP_BLK_REV_3_0	0x02080300
+
+/* Freescale-specific PCI config registers */
+#define FSL_PCI_PBFR		0x44
+
+#ifdef CONFIG_SYS_FSL_PCI_VER_3_X
+/* Currently only the PCIe capability is used, so hardcode the offset.
+ * if more capabilities need to be justified, the capability link method
+ * should be applied here
+ */
+#define FSL_PCIE_CAP_ID		0x70
+#define PCI_DCR		0x78    /* PCIe Device Control Register */
+#define PCI_DSR		0x7a    /* PCIe Device Status Register */
+#define PCI_LSR		0x82    /* PCIe Link Status Register */
+#define PCI_LCR		0x80    /* PCIe Link Control Register */
+#else
+#define FSL_PCIE_CAP_ID		0x4c
+#define PCI_DCR		0x54    /* PCIe Device Control Register */
+#define PCI_DSR		0x56    /* PCIe Device Status Register */
+#define PCI_LSR		0x5e    /* PCIe Link Status Register */
+#define PCI_LCR		0x5c    /* PCIe Link Control Register */
+#endif
+
+#define FSL_PCIE_CFG_RDY	0x4b0
+#define FSL_PROG_IF_AGENT	0x1
+
+#define PCI_LTSSM	0x404   /* PCIe Link Training, Status State Machine */
+#define  PCI_LTSSM_L0	0x16    /* L0 state */
 
 int fsl_setup_hose(struct pci_controller *hose, unsigned long addr);
 int fsl_is_pci_agent(struct pci_controller *hose);
@@ -149,7 +177,10 @@ typedef struct ccsr_pci {
 	u32	perr_cap3;	/* 0xe34 - PCIE Error Capture Register 3 */
 	char	res23[200];
 	u32	pdb_stat;	/* 0xf00 - PCIE Debug Status */
-	char	res24[252];
+	char	res24[16];
+	u32	pex_csr0;	/* 0xf14 - PEX Control/Status register 0*/
+	u32	pex_csr1;	/* 0xf18 - PEX Control/Status register 1*/
+	char	res25[228];
 } ccsr_fsl_pci_t;
 #define PCIE_CONFIG_PC	0x00020000
 #define PCIE_CONFIG_OB_CK	0x00002000

arch/powerpc/include/asm/fsl_serdes.h

@@ -90,6 +90,7 @@ void fsl_serdes_init(void);
 #ifdef CONFIG_FSL_CORENET
 #ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2
 int serdes_get_first_lane(u32 sd, enum srds_prtcl device);
+enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane);
 #else
 int serdes_get_first_lane(enum srds_prtcl device);
 #endif

arch/powerpc/include/asm/immap_85xx.h

@@ -1544,6 +1544,18 @@ struct rio_pw {
 };
 #endif
 
+#ifdef CONFIG_SYS_FSL_SRIO_LIODN
+struct rio_liodn {
+	u32	plbr;
+	u8	res0[28];
+	u32	plaor;
+	u8	res1[12];
+	u32	pludr;
+	u32	plldr;
+	u8	res2[456];
+};
+#endif
+
 /* RapidIO Registers */
 struct ccsr_rio {
 	struct rio_arch	arch;
@@ -1566,6 +1578,10 @@ struct ccsr_rio {
 	u8	res7[100];
 	struct rio_pw	pw;
 #endif
+#ifdef CONFIG_SYS_FSL_SRIO_LIODN
+	u8	res5[8192];
+	struct rio_liodn liodn[CONFIG_SYS_FSL_SRIO_MAX_PORTS];
+#endif
 };
 #endif
 
@@ -2131,6 +2147,11 @@ typedef struct ccsr_gur {
 #ifdef CONFIG_MPC8536
 #define MPC85xx_PORPLLSR_DDR_RATIO	0x3e000000
 #define MPC85xx_PORPLLSR_DDR_RATIO_SHIFT	25
+#elif defined(CONFIG_PPC_C29X)
+#define MPC85xx_PORPLLSR_DDR_RATIO	0x00003f00
+#define MPC85xx_PORPLLSR_DDR_RATIO_SHIFT	(9 - ((gur->pordevsr2 \
+					& MPC85xx_PORDEVSR2_DDR_SPD_0) \
+					>> MPC85xx_PORDEVSR2_DDR_SPD_0_SHIFT))
 #else
 #if defined(CONFIG_BSC9131) || defined(CONFIG_BSC9132)
 #define MPC85xx_PORPLLSR_DDR_RATIO	0x00003f00
@@ -2178,6 +2199,9 @@ typedef struct ccsr_gur {
 #elif defined(CONFIG_BSC9132)
 #define MPC85xx_PORDEVSR_IO_SEL		0x00FE0000
 #define MPC85xx_PORDEVSR_IO_SEL_SHIFT	17
+#elif defined(CONFIG_PPC_C29X)
+#define MPC85xx_PORDEVSR_IO_SEL		0x00e00000
+#define MPC85xx_PORDEVSR_IO_SEL_SHIFT	21
 #else
 #define MPC85xx_PORDEVSR_IO_SEL		0x00780000
 #define MPC85xx_PORDEVSR_IO_SEL_SHIFT	19
@@ -2193,6 +2217,10 @@ typedef struct ccsr_gur {
 #define MPC85xx_PORDEVSR_RIO_DEV_ID	0x00000007
 	u32	pordbgmsr;	/* POR debug mode status */
 	u32	pordevsr2;	/* POR I/O device status 2 */
+#if defined(CONFIG_PPC_C29X)
+#define MPC85xx_PORDEVSR2_DDR_SPD_0	0x00000008
+#define MPC85xx_PORDEVSR2_DDR_SPD_0_SHIFT	3
+#endif
 /* The 8544 RM says this is bit 26, but it's really bit 24 */
 #define MPC85xx_PORDEVSR2_SEC_CFG	0x00000080
 	u8	res1[8];
@@ -2339,6 +2367,11 @@ typedef struct ccsr_gur {
 #define MPC85xx_PMUXCR0_SIM_SEL_MASK	0x0003b000
 #define MPC85xx_PMUXCR0_SIM_SEL		0x00014000
 #endif
+#if defined(CONFIG_PPC_C29X)
+#define MPC85xx_PMUXCR_SPI_MASK			0x00000300
+#define MPC85xx_PMUXCR_SPI			0x00000000
+#define MPC85xx_PMUXCR_SPI_GPIO			0x00000100
+#endif
 	u32	pmuxcr2;	/* Alt. function signal multiplex control 2 */
 #if defined(CONFIG_P1010) || defined(CONFIG_P1014)
 #define MPC85xx_PMUXCR2_UART_GPIO		0x40000000
@@ -2526,7 +2559,9 @@ typedef struct serdes_corenet {
 #define SRDS_RSTCTL_RSTDONE	0x40000000
 #define SRDS_RSTCTL_RSTERR	0x20000000
 #define SRDS_RSTCTL_SWRST	0x10000000
-#define SRDS_RSTCTL_SDPD	0x00000020
+#define SRDS_RSTCTL_SDEN	0x00000020
+#define SRDS_RSTCTL_SDRST_B	0x00000040
+#define SRDS_RSTCTL_PLLRST_B	0x00000080
 		u32	pllcr0; /* PLL Control Register 0 */
 #define SRDS_PLLCR0_POFF		0x80000000
 #define SRDS_PLLCR0_RFCK_SEL_MASK	0x70000000
@@ -3008,12 +3043,18 @@ struct ccsr_pman {
 #define CONFIG_SYS_MPC85xx_USB2_OFFSET		0x23000
 #ifdef CONFIG_TSECV2
 #define CONFIG_SYS_TSEC1_OFFSET			0xB0000
+#elif defined(CONFIG_TSECV2_1)
+#define CONFIG_SYS_TSEC1_OFFSET			0x10000
 #else
 #define CONFIG_SYS_TSEC1_OFFSET			0x24000
 #endif
 #define CONFIG_SYS_MDIO1_OFFSET			0x24000
 #define CONFIG_SYS_MPC85xx_ESDHC_OFFSET		0x2e000
+#if defined(CONFIG_PPC_C29X)
+#define CONFIG_SYS_FSL_SEC_OFFSET		0x80000
+#else
 #define CONFIG_SYS_FSL_SEC_OFFSET		0x30000
+#endif
 #define CONFIG_SYS_MPC85xx_SERDES2_OFFSET	0xE3100
 #define CONFIG_SYS_MPC85xx_SERDES1_OFFSET	0xE3000
 #define CONFIG_SYS_SNVS_OFFSET			0xE6000
@@ -3031,6 +3072,12 @@ struct ccsr_pman {
 #define CONFIG_SYS_MPC85xx_GUTS_OFFSET		0xE0000
 #define CONFIG_SYS_FSL_SRIO_OFFSET		0xC0000
 
+#if defined(CONFIG_BSC9132)
+#define CONFIG_SYS_FSL_DSP_CCSR_DDR_OFFSET	0x10000
+#define CONFIG_SYS_FSL_DSP_CCSR_DDR_ADDR \
+	(CONFIG_SYS_FSL_DSP_CCSRBAR + CONFIG_SYS_FSL_DSP_CCSR_DDR_OFFSET)
+#endif
+
 #define CONFIG_SYS_FSL_CPC_ADDR	\
 	(CONFIG_SYS_CCSRBAR + CONFIG_SYS_FSL_CPC_OFFSET)
 #define CONFIG_SYS_FSL_QMAN_ADDR \

arch/powerpc/include/asm/processor.h

@@ -1119,6 +1119,9 @@
 #define SVR_T4240	0x824000
 #define SVR_T4120	0x824001
 #define SVR_T4160	0x824100
+#define SVR_C291	0x850000
+#define SVR_C292	0x850020
+#define SVR_C293	0x850030
 #define SVR_B4860	0X868000
 #define SVR_G4860	0x868001
 #define SVR_G4060	0x868003

board/freescale/b4860qds/b4860qds.c

@@ -21,12 +21,14 @@
 
 #include "../common/qixis.h"
 #include "../common/vsc3316_3308.h"
+#include "../common/idt8t49n222a_serdes_clk.h"
 #include "b4860qds.h"
 #include "b4860qds_qixis.h"
 #include "b4860qds_crossbar_con.h"
 
 #define CLK_MUX_SEL_MASK	0x4
 #define ETH_PHY_CLK_OUT		0x4
+#define PLL_NUM			2
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -35,8 +37,6 @@ int checkboard(void)
 	char buf[64];
 	u8 sw;
 	struct cpu_type *cpu = gd->arch.cpu;
-	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-	unsigned int i;
 	static const char *const freq[] = {"100", "125", "156.25", "161.13",
 						"122.88", "122.88", "122.88"};
 	int clock;
@@ -61,19 +61,6 @@ int checkboard(void)
 	/* the timestamp string contains "\n" at the end */
 	printf(" on %s", qixis_read_time(buf));
 
-	/* Display the RCW, so that no one gets confused as to what RCW
-	 * we're actually using for this boot.
-	 */
-	puts("Reset Configuration Word (RCW):");
-	for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
-		u32 rcw = in_be32(&gur->rcwsr[i]);
-
-		if ((i % 4) == 0)
-			printf("\n       %08x:", i * 4);
-		printf(" %08x", rcw);
-	}
-	puts("\n");
-
 	/*
 	 * Display the actual SERDES reference clocks as configured by the
 	 * dip switches on the board.  Note that the SWx registers could
@@ -252,6 +239,106 @@ int configure_vsc3316_3308(void)
 	return 0;
 }
 
+int config_serdes1_refclks(void)
+{
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	serdes_corenet_t *srds_regs =
+		(void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+	u32 serdes1_prtcl, lane;
+	unsigned int flag_sgmii_prtcl = 0;
+	int ret, i;
+
+	serdes1_prtcl = in_be32(&gur->rcwsr[4]) &
+			FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+	if (!serdes1_prtcl) {
+		printf("SERDES1 is not enabled\n");
+		return -1;
+	}
+	serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+	debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl);
+
+	/* Clear SRDS_RSTCTL_RST bit for both PLLs before changing refclks
+	 */
+	for (i = 0; i < PLL_NUM; i++)
+		clrbits_be32(&srds_regs->bank[i].rstctl, SRDS_RSTCTL_RST);
+	/* Reconfigure IDT idt8t49n222a device for CPRI to work
+	 * For this SerDes1's Refclk1 and refclk2 need to be set
+	 * to 122.88MHz
+	 */
+	switch (serdes1_prtcl) {
+	case 0x2A:
+	case 0x2C:
+	case 0x2D:
+	case 0x2E:
+		debug("Configuring idt8t49n222a for CPRI SerDes clks:"
+			" for srds_prctl:%x\n", serdes1_prtcl);
+		ret = select_i2c_ch_pca(I2C_CH_IDT);
+		if (!ret) {
+			ret = set_serdes_refclk(IDT_SERDES1_ADDRESS, 1,
+					SERDES_REFCLK_122_88,
+					SERDES_REFCLK_122_88, 0);
+			if (ret) {
+				printf("IDT8T49N222A configuration failed.\n");
+				return ret;
+			} else
+				printf("IDT8T49N222A configured.\n");
+		} else {
+			return ret;
+		}
+		select_i2c_ch_pca(I2C_CH_DEFAULT);
+
+		/* Change SerDes1's Refclk1 to 125MHz for on board
+		 * SGMIIs to work
+		 */
+		for (lane = 0; lane < SRDS_MAX_LANES; lane++) {
+			enum srds_prtcl lane_prtcl = serdes_get_prtcl
+						(0, serdes1_prtcl, lane);
+			switch (lane_prtcl) {
+			case SGMII_FM1_DTSEC1:
+			case SGMII_FM1_DTSEC2:
+			case SGMII_FM1_DTSEC3:
+			case SGMII_FM1_DTSEC4:
+			case SGMII_FM1_DTSEC5:
+			case SGMII_FM1_DTSEC6:
+				flag_sgmii_prtcl++;
+				break;
+			default:
+				break;
+			}
+		}
+
+		if (flag_sgmii_prtcl)
+			QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125);
+
+		/* Steps For SerDes PLLs reset and reconfiguration after
+		 * changing SerDes's refclks
+		 */
+		for (i = 0; i < PLL_NUM; i++) {
+			debug("For PLL%d reset and reconfiguration after"
+			       " changing refclks\n", i+1);
+			clrbits_be32(&srds_regs->bank[i].rstctl,
+					SRDS_RSTCTL_SDRST_B);
+			udelay(10);
+			clrbits_be32(&srds_regs->bank[i].rstctl,
+				(SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B));
+			udelay(10);
+			setbits_be32(&srds_regs->bank[i].rstctl,
+					SRDS_RSTCTL_RST);
+			setbits_be32(&srds_regs->bank[i].rstctl,
+				(SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B
+				| SRDS_RSTCTL_SDRST_B));
+		}
+		break;
+	default:
+		printf("WARNING:IDT8T49N222A configuration not"
+			" supported for:%x SerDes1 Protocol.\n",
+			serdes1_prtcl);
+		return -1;
+	}
+
+	return 0;
+}
+
 int board_early_init_r(void)
 {
 	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
@@ -277,6 +364,16 @@ int board_early_init_r(void)
 #ifdef CONFIG_SYS_DPAA_QBMAN
 	setup_portals();
 #endif
+	/* SerDes1 refclks need to be set again, as default clks
+	 * are not suitable for CPRI and onboard SGMIIs to work
+	 * simultaneously.
+	 * This function will set SerDes1's Refclk1 and refclk2
+	 * as per SerDes1 protocols
+	 */
+	if (config_serdes1_refclks())
+		printf("SerDes1 Refclks couldn't set properly.\n");
+	else
+		printf("SerDes1 Refclks have been set.\n");
 
 	/* Configure VSC3316 and VSC3308 crossbar switches */
 	if (configure_vsc3316_3308())

board/freescale/b4860qds/eth_b4860qds.c

@@ -201,8 +201,6 @@ int board_eth_init(bd_t *bis)
 		debug("Setting phy addresses for FM1_DTSEC5: %x and"
 			"FM1_DTSEC6: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR,
 			CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
-		/* Fixing Serdes clock by programming FPGA register */
-		QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125);
 		fm_info_set_phy_address(FM1_DTSEC5,
 				CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
 		fm_info_set_phy_address(FM1_DTSEC6,

board/freescale/bsc9131rdb/ddr.c

@@ -87,7 +87,7 @@ phys_size_t fixed_sdram(void)
 	}
 
 	ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
 
 	if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, ddr_size,
 					LAW_TRGT_IF_DDR_1) < 0) {

board/freescale/bsc9132qds/bsc9132qds.c

@@ -125,6 +125,27 @@ void board_config_serdes_mux(void)
 	}
 }
 
+/* Configure DSP DDR controller */
+void dsp_ddr_configure(void)
+{
+	/*
+	 *There are separate DDR-controllers for DSP and PowerPC side DDR.
+	 *copy the ddr controller settings from PowerPC side DDR controller
+	 *to the DSP DDR controller as connected DDR memories are similar.
+	 */
+	ccsr_ddr_t __iomem *pa_ddr =
+			(ccsr_ddr_t __iomem *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+	ccsr_ddr_t temp_ddr;
+	ccsr_ddr_t __iomem *dsp_ddr =
+			(ccsr_ddr_t __iomem *)CONFIG_SYS_FSL_DSP_CCSR_DDR_ADDR;
+
+	memcpy(&temp_ddr, pa_ddr, sizeof(ccsr_ddr_t));
+	temp_ddr.cs0_bnds = CONFIG_SYS_DDR1_CS0_BNDS;
+	temp_ddr.sdram_cfg &= ~SDRAM_CFG_MEM_EN;
+	memcpy(dsp_ddr, &temp_ddr, sizeof(ccsr_ddr_t));
+	dsp_ddr->sdram_cfg |= SDRAM_CFG_MEM_EN;
+}
+
 int board_early_init_r(void)
 {
 #ifndef CONFIG_SYS_NO_FLASH
@@ -153,6 +174,7 @@ int board_early_init_r(void)
 			0, flash_esel+1, BOOKE_PAGESZ_64M, 1);
 #endif
 	board_config_serdes_mux();
+	dsp_ddr_configure();
 	return 0;
 }
 

board/freescale/bsc9132qds/ddr.c

@@ -109,7 +109,7 @@ phys_size_t fixed_sdram(void)
 					strmhz(buf, ddr_freq));
 
 	ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
 
 	if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, ddr_size,
 					LAW_TRGT_IF_DDR_1) < 0) {

board/freescale/bsc9132qds/law.c

@@ -16,6 +16,14 @@ struct law_entry law_table[] = {
 #ifdef CONFIG_SYS_FPGA_BASE_PHYS
 	SET_LAW(CONFIG_SYS_FPGA_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC),
 #endif
+	SET_LAW(CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS, LAW_SIZE_1M,
+		LAW_TRGT_IF_DSP_CCSR),
+	SET_LAW(CONFIG_SYS_FSL_DSP_M2_RAM_ADDR, LAW_SIZE_32M,
+		LAW_TRGT_IF_OCN_DSP),
+	SET_LAW(CONFIG_SYS_FSL_DSP_M3_RAM_ADDR, LAW_SIZE_32K,
+		LAW_TRGT_IF_CLASS_DSP),
+	SET_LAW(CONFIG_SYS_FSL_DSP_DDR_ADDR, LAW_SIZE_1G,
+		LAW_TRGT_IF_CLASS_DSP)
 };
 
 int num_law_entries = ARRAY_SIZE(law_table);

board/freescale/bsc9132qds/tlb.c

@@ -41,6 +41,11 @@ struct fsl_e_tlb_entry tlb_table[] = {
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 			0, 1, BOOKE_PAGESZ_1M, 1),
 
+	/* CCSRBAR (DSP) */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FSL_DSP_CCSRBAR,
+		      CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS, MAS3_SW|MAS3_SR,
+		      MAS2_I|MAS2_G, 0, 2, BOOKE_PAGESZ_1M, 1),
+
 #ifndef CONFIG_SPL_BUILD
 	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
 			MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,

board/freescale/c29xpcie/Makefile

@@ -0,0 +1,30 @@
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= cpld.o
+COBJS-y	+= ddr.o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/freescale/c29xpcie/c29xpcie.c

@@ -0,0 +1,148 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <pci.h>
+#include <asm/fsl_ifc.h>
+#include <asm/fsl_pci.h>
+
+#include "cpld.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	struct cpu_type *cpu = gd->arch.cpu;
+	struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
+
+	printf("Board: %sPCIe, ", cpu->name);
+	printf("CPLD Ver: 0x%02x\n", in_8(&cpld_data->cpldver));
+
+	return 0;
+}
+
+int board_early_init_f(void)
+{
+	struct fsl_ifc *ifc = (void *)CONFIG_SYS_IFC_ADDR;
+
+	/* Clock configuration to access CPLD using IFC(GPCM) */
+	setbits_be32(&ifc->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT);
+
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+	const unsigned long flashbase = CONFIG_SYS_FLASH_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, flash_esel, BOOKE_PAGESZ_64M, 1);
+
+	return 0;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+	fsl_pcie_init_board(0);
+}
+#endif /* ifdef CONFIG_PCI */
+
+#ifdef CONFIG_TSEC_ENET
+int board_eth_init(bd_t *bis)
+{
+	struct fsl_pq_mdio_info mdio_info;
+	struct tsec_info_struct tsec_info[2];
+	int num = 0;
+
+#ifdef CONFIG_TSEC1
+	SET_STD_TSEC_INFO(tsec_info[num], 1);
+	num++;
+#endif
+#ifdef CONFIG_TSEC2
+	SET_STD_TSEC_INFO(tsec_info[num], 2);
+	num++;
+#endif
+	if (!num) {
+		printf("No TSECs initialized\n");
+		return 0;
+	}
+
+	/* Register 1G MDIO bus */
+	mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+	mdio_info.name = DEFAULT_MII_NAME;
+
+	fsl_pq_mdio_init(bis, &mdio_info);
+
+	tsec_eth_init(bis, tsec_info, num);
+
+	return pci_eth_init(bis);
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void fdt_del_sec(void *blob, int offset)
+{
+	int nodeoff = 0;
+
+	while ((nodeoff = fdt_node_offset_by_compat_reg(blob, "fsl,sec-v6.0",
+			CONFIG_SYS_CCSRBAR_PHYS + CONFIG_SYS_FSL_SEC_OFFSET
+			+ offset * 0x20000)) >= 0) {
+		fdt_del_node(blob, nodeoff);
+		offset++;
+	}
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+	struct cpu_type *cpu;
+
+	cpu = gd->arch.cpu;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+#if defined(CONFIG_PCI)
+	FT_FSL_PCI_SETUP;
+#endif
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+	if (cpu->soc_ver == SVR_C291)
+		fdt_del_sec(blob, 1);
+	else if (cpu->soc_ver == SVR_C292)
+		fdt_del_sec(blob, 2);
+}
+#endif

board/freescale/c29xpcie/cpld.c

@@ -0,0 +1,131 @@
+/**
+ * Copyright 2013 Freescale Semiconductor
+ * Author: Mingkai Hu <Mingkai.hu@freescale.com>
+ *         Po Liu <Po.Liu@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * This file provides support for the board-specific CPLD used on some Freescale
+ * reference boards.
+ *
+ * The following macros need to be defined:
+ *
+ * CONFIG_SYS_CPLD_BASE - The virtual address of the base of the
+ * CPLD register map
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+
+#include "cpld.h"
+/**
+ * Set the boot bank to the alternate bank
+ */
+void cpld_set_altbank(u8 banksel)
+{
+	struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
+	u8 reg11;
+
+	reg11 = in_8(&cpld_data->flhcsr);
+
+	switch (banksel) {
+	case 1:
+		out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK)
+			| CPLD_BANKSEL_EN | CPLD_SELECT_BANK1);
+		break;
+	case 2:
+		out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK)
+			| CPLD_BANKSEL_EN | CPLD_SELECT_BANK2);
+		break;
+	case 3:
+		out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK)
+			| CPLD_BANKSEL_EN | CPLD_SELECT_BANK3);
+		break;
+	case 4:
+		out_8(&cpld_data->flhcsr, (reg11 & CPLD_BANKSEL_MASK)
+			| CPLD_BANKSEL_EN | CPLD_SELECT_BANK4);
+		break;
+	default:
+		printf("Invalid value! [1-4]\n");
+		return;
+	}
+
+	udelay(100);
+	do_reset(NULL, 0, 0, NULL);
+}
+
+/**
+ * Set the boot bank to the default bank
+ */
+void cpld_set_defbank(void)
+{
+	cpld_set_altbank(4);
+}
+
+#ifdef DEBUG
+static void cpld_dump_regs(void)
+{
+	struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
+
+	printf("chipid1		= 0x%02x\n", in_8(&cpld_data->chipid1));
+	printf("chipid2		= 0x%02x\n", in_8(&cpld_data->chipid2));
+	printf("hwver		= 0x%02x\n", in_8(&cpld_data->hwver));
+	printf("cpldver		= 0x%02x\n", in_8(&cpld_data->cpldver));
+	printf("rstcon		= 0x%02x\n", in_8(&cpld_data->rstcon));
+	printf("flhcsr		= 0x%02x\n", in_8(&cpld_data->flhcsr));
+	printf("wdcsr		= 0x%02x\n", in_8(&cpld_data->wdcsr));
+	printf("wdkick		= 0x%02x\n", in_8(&cpld_data->wdkick));
+	printf("fancsr		= 0x%02x\n", in_8(&cpld_data->fancsr));
+	printf("ledcsr		= 0x%02x\n", in_8(&cpld_data->ledcsr));
+	printf("misc		= 0x%02x\n", in_8(&cpld_data->misccsr));
+	printf("bootor		= 0x%02x\n", in_8(&cpld_data->bootor));
+	printf("bootcfg1	= 0x%02x\n", in_8(&cpld_data->bootcfg1));
+	printf("bootcfg2	= 0x%02x\n", in_8(&cpld_data->bootcfg2));
+	printf("bootcfg3	= 0x%02x\n", in_8(&cpld_data->bootcfg3));
+	printf("bootcfg4	= 0x%02x\n", in_8(&cpld_data->bootcfg4));
+	putc('\n');
+}
+#endif
+
+int cpld_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	int rc = 0;
+	unsigned char value;
+
+	if (argc <= 1)
+		return cmd_usage(cmdtp);
+
+	if (strcmp(argv[1], "reset") == 0) {
+		if (!strcmp(argv[2], "altbank") && argv[3]) {
+			value = (u8)simple_strtoul(argv[3], NULL, 16);
+			cpld_set_altbank(value);
+		} else if (!argv[2])
+			cpld_set_defbank();
+		else
+			cmd_usage(cmdtp);
+#ifdef DEBUG
+	} else if (strcmp(argv[1], "dump") == 0) {
+		cpld_dump_regs();
+#endif
+	} else
+		rc = cmd_usage(cmdtp);
+
+	return rc;
+}
+
+U_BOOT_CMD(
+	cpld_cmd, CONFIG_SYS_MAXARGS, 1, cpld_cmd,
+	"Reset the board using the CPLD sequencer",
+	"reset - hard reset to default bank 4\n"
+	"cpld_cmd reset altbank [bank]- reset to alternate bank\n"
+	"	- [bank] bank value select 1-4\n"
+	"	- bank 1 on the flash 0x0000000~0x0ffffff\n"
+	"	- bank 2 on the flash 0x1000000~0x1ffffff\n"
+	"	- bank 3 on the flash 0x2000000~0x2ffffff\n"
+	"	- bank 4 on the flash 0x3000000~0x3ffffff\n"
+#ifdef DEBUG
+	"cpld_cmd dump - display the CPLD registers\n"
+#endif
+	);

board/freescale/c29xpcie/cpld.h

@@ -0,0 +1,40 @@
+/**
+ * Copyright 2013 Freescale Semiconductor
+ * Author: Mingkai Hu <Mingkai.Hu@freescale.com>
+ *         Po Liu <Po.Liu@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * This file provides support for the ngPIXIS, a board-specific FPGA used on
+ * some Freescale reference boards.
+ */
+
+/*
+ * CPLD register set. Feel free to add board-specific #ifdefs where necessary.
+ */
+struct cpld_data {
+	u8 chipid1;	/* 0x0 - CPLD Chip ID1 Register */
+	u8 chipid2;	/* 0x1 - CPLD Chip ID2 Register */
+	u8 hwver;	/* 0x2 - Hardware Version Register */
+	u8 cpldver;	/* 0x3 - Software Version Register */
+	u8 res[12];
+	u8 rstcon;	/* 0x10 - Reset control register */
+	u8 flhcsr;	/* 0x11 - Flash control and status Register */
+	u8 wdcsr;	/* 0x12 - Watchdog control and status Register */
+	u8 wdkick;	/* 0x13 - Watchdog kick Register */
+	u8 fancsr;	/* 0x14 - Fan control and status Register */
+	u8 ledcsr;	/* 0x15 - LED control and status Register */
+	u8 misccsr;	/* 0x16 - Misc control and status Register */
+	u8 bootor;	/* 0x17 - Boot configure override Register */
+	u8 bootcfg1;	/* 0x18 - Boot configure 1 Register */
+	u8 bootcfg2;	/* 0x19 - Boot configure 2 Register */
+	u8 bootcfg3;	/* 0x1a - Boot configure 3 Register */
+	u8 bootcfg4;	/* 0x1b - Boot configure 4 Register */
+};
+
+#define CPLD_BANKSEL_EN		0x02
+#define CPLD_BANKSEL_MASK	0x3f
+#define CPLD_SELECT_BANK1	0xc0
+#define CPLD_SELECT_BANK2	0x80
+#define CPLD_SELECT_BANK3	0x40
+#define CPLD_SELECT_BANK4	0x00

board/freescale/c29xpcie/ddr.c

@@ -0,0 +1,86 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+/*
+ * Micron MT41J128M16HA-15E
+ * */
+dimm_params_t ddr_raw_timing = {
+	.n_ranks = 1,
+	.rank_density = 536870912u,
+	.capacity = 536870912u,
+	.primary_sdram_width = 32,
+	.ec_sdram_width = 8,
+	.registered_dimm = 0,
+	.mirrored_dimm = 0,
+	.n_row_addr = 14,
+	.n_col_addr = 10,
+	.n_banks_per_sdram_device = 8,
+	.edc_config = 2,
+	.burst_lengths_bitmask = 0x0c,
+
+	.tCKmin_X_ps = 1650,
+	.caslat_X = 0x7e << 4,	/* 5,6,7,8,9,10 */
+	.tAA_ps = 14050,
+	.tWR_ps = 15000,
+	.tRCD_ps = 13500,
+	.tRRD_ps = 75000,
+	.tRP_ps = 13500,
+	.tRAS_ps = 40000,
+	.tRC_ps = 49500,
+	.tRFC_ps = 160000,
+	.tWTR_ps = 75000,
+	.tRTP_ps = 75000,
+	.refresh_rate_ps = 7800000,
+	.tFAW_ps = 30000,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+		unsigned int controller_number,
+		unsigned int dimm_number)
+{
+	const char dimm_model[] = "Fixed DDR on board";
+
+	if ((controller_number == 0) && (dimm_number == 0)) {
+		memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+		memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+		memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+	}
+
+	return 0;
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	int i;
+	popts->clk_adjust = 2;
+	popts->cpo_override = 0x1f;
+	popts->write_data_delay = 4;
+	popts->half_strength_driver_enable = 1;
+	popts->bstopre = 0x3cf;
+	popts->quad_rank_present = 1;
+	popts->rtt_override = 1;
+	popts->rtt_override_value = 1;
+	popts->dynamic_power = 1;
+	/* Write leveling override */
+	popts->wrlvl_en = 1;
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+	popts->wrlvl_start = 0x4;
+	popts->trwt_override = 1;
+	popts->trwt = 0;
+
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER;
+		popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS;
+	}
+}

board/freescale/c29xpcie/law.c

@@ -0,0 +1,19 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_IFC),
+	SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_16K, LAW_TRGT_IF_IFC),
+	SET_LAW(CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS, LAW_SIZE_512K,
+					LAW_TRGT_IF_PLATFORM_SRAM),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);

board/freescale/c29xpcie/tlb.c

@@ -0,0 +1,76 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
+			CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
+			CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
+			CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 0, BOOKE_PAGESZ_1M, 1),
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+			MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+			0, 1, BOOKE_PAGESZ_64M, 1),
+
+#ifdef CONFIG_PCI
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 2, BOOKE_PAGESZ_256M, 1),
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 3, BOOKE_PAGESZ_256K, 1),
+#endif
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 4, BOOKE_PAGESZ_4K, 1),
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 5, BOOKE_PAGESZ_16K, 1),
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_PLATFORM_SRAM_BASE,
+			CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 6, BOOKE_PAGESZ_256K, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_PLATFORM_SRAM_BASE + 0x40000,
+			CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS + 0x40000,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 7, BOOKE_PAGESZ_256K, 1),
+
+#ifdef CONFIG_SYS_RAMBOOT
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE,
+			CONFIG_SYS_DDR_SDRAM_BASE,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 8, BOOKE_PAGESZ_256M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
+			CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 9, BOOKE_PAGESZ_256M, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);

board/freescale/common/Makefile

@@ -54,6 +54,7 @@ COBJS-$(CONFIG_P4080DS)		+= ics307_clk.o
 COBJS-$(CONFIG_P5020DS)		+= ics307_clk.o
 COBJS-$(CONFIG_P5040DS)		+= ics307_clk.o
 COBJS-$(CONFIG_VSC_CROSSBAR)    += vsc3316_3308.o
+COBJS-$(CONFIG_IDT8T49N222A)	+= idt8t49n222a_serdes_clk.o
 
 # deal with common files for P-series corenet based devices
 SUBLIB-$(CONFIG_P2041RDB)	+= p_corenet/libp_corenet.o

board/freescale/common/idt8t49n222a_serdes_clk.c

@@ -0,0 +1,207 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ * Author: Shaveta Leekha <shaveta@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include "idt8t49n222a_serdes_clk.h"
+
+#define DEVICE_ID_REG		0x00
+
+static int check_pll_status(u8 idt_addr)
+{
+	u8 val = 0;
+	int ret;
+
+	ret = i2c_read(idt_addr, 0x17, 1, &val, 1);
+	if (ret < 0) {
+		printf("IDT:0x%x could not read status register from device.\n",
+			idt_addr);
+		return ret;
+	}
+
+	if (val & 0x04) {
+		debug("idt8t49n222a PLL is LOCKED: %x\n", val);
+	} else {
+		printf("idt8t49n222a PLL is not LOCKED: %x\n", val);
+		return -1;
+	}
+
+	return 0;
+}
+
+int set_serdes_refclk(u8 idt_addr, u8 serdes_num,
+			enum serdes_refclk refclk1,
+			enum serdes_refclk refclk2, u8 feedback)
+{
+	u8 dev_id = 0;
+	int i, ret;
+
+	debug("IDT:Configuring idt8t49n222a device at I2C address: 0x%2x\n",
+		idt_addr);
+
+	ret = i2c_read(idt_addr, DEVICE_ID_REG, 1, &dev_id, 1);
+	if (ret < 0) {
+		debug("IDT:0x%x could not read DEV_ID from device.\n",
+			idt_addr);
+		return ret;
+	}
+
+	if ((dev_id != 0x00) && (dev_id != 0x24) && (dev_id != 0x2a)) {
+		debug("IDT: device at address 0x%x is not idt8t49n222a.\n",
+			idt_addr);
+	}
+
+	if (serdes_num != 1 && serdes_num != 2) {
+		debug("serdes_num should be 1 for SerDes1 and"
+			" 2 for SerDes2.\n");
+		return -1;
+	}
+
+	if ((refclk1 == SERDES_REFCLK_122_88 && refclk2 != SERDES_REFCLK_122_88)
+		|| (refclk1 != SERDES_REFCLK_122_88
+			&& refclk2 == SERDES_REFCLK_122_88)) {
+		debug("Only one refclk at 122.88MHz is not supported."
+			" Please set both refclk1 & refclk2 to 122.88MHz"
+			" or both not to 122.88MHz.\n");
+		return -1;
+	}
+
+	if (refclk1 != SERDES_REFCLK_100 && refclk1 != SERDES_REFCLK_122_88
+					&& refclk1 != SERDES_REFCLK_125
+					&& refclk1 != SERDES_REFCLK_156_25) {
+		debug("refclk1 should be 100MHZ, 122.88MHz, 125MHz"
+			" or 156.25MHz.\n");
+		return -1;
+	}
+
+	if (refclk2 != SERDES_REFCLK_100 && refclk2 != SERDES_REFCLK_122_88
+					&& refclk2 != SERDES_REFCLK_125
+					&& refclk2 != SERDES_REFCLK_156_25) {
+		debug("refclk2 should be 100MHZ, 122.88MHz, 125MHz"
+			" or 156.25MHz.\n");
+		return -1;
+	}
+
+	if (feedback != 0 && feedback != 1) {
+		debug("valid values for feedback are 0(default) or 1.\n");
+		return -1;
+	}
+
+	/* Configuring IDT for output refclks as
+	 * Refclk1 = 122.88MHz  Refclk2 = 122.88MHz
+	 */
+	if (refclk1 == SERDES_REFCLK_122_88 &&
+			refclk2 == SERDES_REFCLK_122_88) {
+		printf("Setting refclk1:122.88 and refclk2:122.88\n");
+		for (i = 0; i < NUM_IDT_REGS; i++)
+			i2c_reg_write(idt_addr, idt_conf_122_88[i][0],
+						idt_conf_122_88[i][1]);
+
+		if (feedback) {
+			for (i = 0; i < NUM_IDT_REGS_FEEDBACK; i++)
+				i2c_reg_write(idt_addr,
+					idt_conf_122_88_feedback[i][0],
+					idt_conf_122_88_feedback[i][1]);
+		}
+	}
+
+	if (refclk1 != SERDES_REFCLK_122_88 &&
+			refclk2 != SERDES_REFCLK_122_88) {
+		for (i = 0; i < NUM_IDT_REGS; i++)
+			i2c_reg_write(idt_addr, idt_conf_not_122_88[i][0],
+						idt_conf_not_122_88[i][1]);
+	}
+
+	/* Configuring IDT for output refclks as
+	 * Refclk1 = 100MHz  Refclk2 = 125MHz
+	 */
+	if (refclk1 == SERDES_REFCLK_100 && refclk2 == SERDES_REFCLK_125) {
+		printf("Setting refclk1:100 and refclk2:125\n");
+		i2c_reg_write(idt_addr, 0x11, 0x10);
+	}
+
+	/* Configuring IDT for output refclks as
+	 * Refclk1 = 125MHz  Refclk2 = 125MHz
+	 */
+	if (refclk1 == SERDES_REFCLK_125 && refclk2 == SERDES_REFCLK_125) {
+		printf("Setting refclk1:125 and refclk2:125\n");
+		i2c_reg_write(idt_addr, 0x10, 0x10);
+		i2c_reg_write(idt_addr, 0x11, 0x10);
+	}
+
+	/* Configuring IDT for output refclks as
+	 * Refclk1 = 125MHz  Refclk2 = 100MHz
+	 */
+	if (refclk1 == SERDES_REFCLK_125 && refclk2 == SERDES_REFCLK_100) {
+		printf("Setting refclk1:125 and refclk2:100\n");
+		i2c_reg_write(idt_addr, 0x10, 0x10);
+	}
+
+	/* Configuring IDT for output refclks as
+	 * Refclk1 = 156.25MHz  Refclk2 = 156.25MHz
+	 */
+	if (refclk1 == SERDES_REFCLK_156_25 &&
+			refclk2 == SERDES_REFCLK_156_25) {
+		printf("Setting refclk1:156.25 and refclk2:156.25\n");
+		for (i = 0; i < NUM_IDT_REGS_156_25; i++)
+			i2c_reg_write(idt_addr, idt_conf_156_25[i][0],
+						idt_conf_156_25[i][1]);
+	}
+
+	/* Configuring IDT for output refclks as
+	 * Refclk1 = 100MHz  Refclk2 = 156.25MHz
+	 */
+	if (refclk1 == SERDES_REFCLK_100 &&
+			refclk2 == SERDES_REFCLK_156_25) {
+		printf("Setting refclk1:100 and refclk2:156.25\n");
+		for (i = 0; i < NUM_IDT_REGS_156_25; i++)
+			i2c_reg_write(idt_addr, idt_conf_100_156_25[i][0],
+						idt_conf_100_156_25[i][1]);
+	}
+
+	/* Configuring IDT for output refclks as
+	 * Refclk1 = 125MHz  Refclk2 = 156.25MHz
+	 */
+	if (refclk1 == SERDES_REFCLK_125 &&
+			refclk2 == SERDES_REFCLK_156_25) {
+		printf("Setting refclk1:125 and refclk2:156.25\n");
+		for (i = 0; i < NUM_IDT_REGS_156_25; i++)
+			i2c_reg_write(idt_addr, idt_conf_125_156_25[i][0],
+						idt_conf_125_156_25[i][1]);
+	}
+
+	/* Configuring IDT for output refclks as
+	 * Refclk1 = 156.25MHz  Refclk2 = 100MHz
+	 */
+	if (refclk1 == SERDES_REFCLK_156_25 &&
+			refclk2 == SERDES_REFCLK_100) {
+		printf("Setting refclk1:156.25 and refclk2:100\n");
+		for (i = 0; i < NUM_IDT_REGS_156_25; i++)
+			i2c_reg_write(idt_addr, idt_conf_156_25_100[i][0],
+						idt_conf_156_25_100[i][1]);
+	}
+
+	/* Configuring IDT for output refclks as
+	 * Refclk1 = 156.25MHz  Refclk2 = 125MHz
+	 */
+	if (refclk1 == SERDES_REFCLK_156_25 &&
+			refclk2 == SERDES_REFCLK_125) {
+		printf("Setting refclk1:156.25 and refclk2:125\n");
+		for (i = 0; i < NUM_IDT_REGS_156_25; i++)
+			i2c_reg_write(idt_addr, idt_conf_156_25_125[i][0],
+						idt_conf_156_25_125[i][1]);
+	}
+
+	/* waiting for maximum of 1 second if PLL doesn'r get locked
+	 * initially. then check the status again.
+	 */
+	if (check_pll_status(idt_addr)) {
+		mdelay(1000);
+		if (check_pll_status(idt_addr))
+			return -1;
+	}
+
+	return 0;
+}

board/freescale/common/idt8t49n222a_serdes_clk.h

@@ -0,0 +1,107 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ * Author: Shaveta Leekha <shaveta@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __IDT8T49N222A_SERDES_CLK_H_
+#define __IDT8T49N222A_SERDES_CLK_H_	1
+
+#include <common.h>
+#include <i2c.h>
+#include "qixis.h"
+#include "../b4860qds/b4860qds_qixis.h"
+#include <errno.h>
+
+#define NUM_IDT_REGS		23
+#define NUM_IDT_REGS_FEEDBACK	12
+#define NUM_IDT_REGS_156_25	11
+
+/* CLK */
+enum serdes_refclk {
+	SERDES_REFCLK_100,	/* refclk 100Mhz */
+	SERDES_REFCLK_122_88,	/* refclk 122.88Mhz */
+	SERDES_REFCLK_125,	/* refclk 125Mhz */
+	SERDES_REFCLK_156_25,	/* refclk 156.25Mhz */
+	SERDES_REFCLK_NONE = -1,
+};
+
+/* configuration values for IDT registers for Output Refclks:
+ * Refclk1 = 122.88MHz Refclk2 = 122.88MHz
+ */
+static const u8 idt_conf_122_88[23][2] = { {0x00, 0x3C}, {0x01, 0x00},
+		{0x02, 0x9F}, {0x03, 0x00}, {0x04, 0x0B}, {0x05, 0x00},
+		{0x06, 0x00}, {0x07, 0x00}, {0x08, 0x7D}, {0x09, 0x00},
+		{0x0A, 0x08}, {0x0B, 0x00}, {0x0C, 0xDC}, {0x0D, 0x00},
+		{0x0E, 0x00}, {0x0F, 0x00}, {0x10, 0x12}, {0x11, 0x12},
+		{0x12, 0xB9}, {0x13, 0xBC}, {0x14, 0x40}, {0x15, 0x08},
+		{0x16, 0xA0} };
+
+
+/* configuration values for IDT registers for Output Refclks:
+ * Refclk1 not equal to 122.88MHz Refclk2 not equal to 122.88MHz
+ */
+static const u8 idt_conf_not_122_88[23][2] = { {0x00, 0x00}, {0x01, 0x00},
+		{0x02, 0x00}, {0x03, 0x00}, {0x04, 0x0A}, {0x05, 0x00},
+		{0x06, 0x00}, {0x07, 0x00}, {0x08, 0x7D}, {0x09, 0x00},
+		{0x0A, 0x08}, {0x0B, 0x00}, {0x0C, 0xDC}, {0x0D, 0x00},
+		{0x0E, 0x00}, {0x0F, 0x00}, {0x10, 0x14}, {0x11, 0x14},
+		{0x12, 0x35}, {0x13, 0xBC}, {0x14, 0x40}, {0x15, 0x08},
+		{0x16, 0xA0} };
+
+/* Reconfiguration values for some of IDT registers for
+ * Output Refclks:
+ * Refclk1 = 122.88MHz Refclk2 = 122.88MHz
+ * and with feedback as 1
+ */
+static const u8 idt_conf_122_88_feedback[12][2] = { {0x00, 0x50}, {0x02, 0xD7},
+		{0x04, 0x89}, {0x06, 0xC3}, {0x08, 0xC0}, {0x0A, 0x07},
+		{0x0C, 0x80}, {0x10, 0x10}, {0x11, 0x10}, {0x12, 0x1B},
+		{0x14, 0x00}, {0x15, 0xE8} };
+
+/* configuration values for IDT registers for Output Refclks:
+ * Refclk1 : 156.25MHz Refclk2 : 156.25MHz
+ */
+static const u8 idt_conf_156_25[11][2] = { {0x04, 0x19}, {0x06, 0x03},
+		{0x08, 0xC0}, {0x0A, 0x07}, {0x0C, 0xA1}, {0x0E, 0x20},
+		{0x10, 0x10}, {0x11, 0x10}, {0x12, 0xB5}, {0x13, 0x3C},
+		{0x15, 0xE8} };
+
+/* configuration values for IDT registers for Output Refclks:
+ * Refclk1 : 100MHz Refclk2 : 156.25MHz
+ */
+static const u8 idt_conf_100_156_25[11][2] = { {0x04, 0x19}, {0x06, 0x03},
+		{0x08, 0xC0}, {0x0A, 0x07}, {0x0C, 0xA1}, {0x0E, 0x20},
+		{0x10, 0x19}, {0x11, 0x10}, {0x12, 0xB5}, {0x13, 0x3C},
+		{0x15, 0xE8} };
+
+/* configuration values for IDT registers for Output Refclks:
+ * Refclk1 : 125MHz Refclk2 : 156.25MHz
+ */
+static const u8 idt_conf_125_156_25[11][2] = { {0x04, 0x19}, {0x06, 0x03},
+		{0x08, 0xC0}, {0x0A, 0x07}, {0x0C, 0xA1}, {0x0E, 0x20},
+		{0x10, 0x14}, {0x11, 0x10}, {0x12, 0xB5}, {0x13, 0x3C},
+		{0x15, 0xE8} };
+
+/* configuration values for IDT registers for Output Refclks:
+ * Refclk1 : 156.25MHz Refclk2 : 100MHz
+ */
+static const u8 idt_conf_156_25_100[11][2] = { {0x04, 0x19}, {0x06, 0x03},
+		{0x08, 0xC0}, {0x0A, 0x07}, {0x0C, 0xA1}, {0x0E, 0x20},
+		{0x10, 0x10}, {0x11, 0x19}, {0x12, 0xB5}, {0x13, 0x3C},
+		{0x15, 0xE8} };
+
+/* configuration values for IDT registers for Output Refclks:
+ * Refclk1 : 156.25MHz Refclk2 : 125MHz
+ */
+static const u8 idt_conf_156_25_125[11][2] = { {0x04, 0x19}, {0x06, 0x03},
+		{0x08, 0xC0}, {0x0A, 0x07}, {0x0C, 0xA1}, {0x0E, 0x20},
+		{0x10, 0x10}, {0x11, 0x14}, {0x12, 0xB5}, {0x13, 0x3C},
+		{0x15, 0xE8} };
+
+int set_serdes_refclk(u8 idt_addr, u8 serdes_num,
+			enum serdes_refclk refclk1,
+			enum serdes_refclk refclk2, u8 feedback);
+
+#endif	/*__IDT8T49N222A_SERDES_CLK_H_ */

board/freescale/common/qixis.c

@@ -107,6 +107,26 @@ const char *byte_to_binary_mask(u8 val, u8 mask, char *buf)
 	return buf;
 }
 
+#ifdef QIXIS_RST_FORCE_MEM
+void board_assert_mem_reset(void)
+{
+	u8 rst;
+
+	rst = QIXIS_READ(rst_frc[0]);
+	if (!(rst & QIXIS_RST_FORCE_MEM))
+		QIXIS_WRITE(rst_frc[0], rst | QIXIS_RST_FORCE_MEM);
+}
+
+void board_deassert_mem_reset(void)
+{
+	u8 rst;
+
+	rst = QIXIS_READ(rst_frc[0]);
+	if (rst & QIXIS_RST_FORCE_MEM)
+		QIXIS_WRITE(rst_frc[0], rst & ~QIXIS_RST_FORCE_MEM);
+}
+#endif
+
 void qixis_reset(void)
 {
 	QIXIS_WRITE(rst_ctl, QIXIS_RST_CTL_RESET);

board/freescale/corenet_ds/corenet_ds.c

@@ -27,8 +27,10 @@ int checkboard (void)
 {
 	u8 sw;
 	struct cpu_type *cpu = gd->arch.cpu;
-	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+#if defined(CONFIG_P3041DS) || defined(CONFIG_P5020DS) || \
+	defined(CONFIG_P5040DS)
 	unsigned int i;
+#endif
 	static const char * const freq[] = {"100", "125", "156.25", "212.5" };
 
 	printf("Board: %sDS, ", cpu->name);
@@ -47,19 +49,6 @@ int checkboard (void)
 	else
 		printf("invalid setting of SW%u\n", PIXIS_LBMAP_SWITCH);
 
-	/* Display the RCW, so that no one gets confused as to what RCW
-	 * we're actually using for this boot.
-	 */
-	puts("Reset Configuration Word (RCW):");
-	for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
-		u32 rcw = in_be32(&gur->rcwsr[i]);
-
-		if ((i % 4) == 0)
-			printf("\n       %08x:", i * 4);
-		printf(" %08x", rcw);
-	}
-	puts("\n");
-
 	/* Display the actual SERDES reference clocks as configured by the
 	 * dip switches on the board.  Note that the SWx registers could
 	 * technically be set to force the reference clocks to match the

board/freescale/corenet_ds/ddr.c

@@ -56,14 +56,14 @@ phys_size_t fixed_sdram(void)
 
 	ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
 	ddr_cfg_regs.ddr_cdr1 = DDR_CDR1_DHC_EN;
-	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
 
 #if (CONFIG_NUM_DDR_CONTROLLERS == 2)
 	memcpy(&ddr_cfg_regs,
 		fixed_ddr_parm_1[i].ddr_settings,
 		sizeof(ddr_cfg_regs));
 	ddr_cfg_regs.ddr_cdr1 = DDR_CDR1_DHC_EN;
-	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 1);
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 1, 0);
 #endif
 
 	/*

board/freescale/p1010rdb/ddr.c

@@ -139,7 +139,7 @@ phys_size_t fixed_sdram(void)
 	}
 
 	ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
 
 	if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, ddr_size,
 					LAW_TRGT_IF_DDR_1) < 0) {

board/freescale/p1_p2_rdb/ddr.c

@@ -220,7 +220,7 @@ phys_size_t fixed_sdram (void)
 		ddr_cfg_regs.cs[0].bnds = 0x0000001F;
 	}
 
-	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
 
 	set_ddr_laws(0, ddr_size, LAW_TRGT_IF_DDR_1);
 	return ddr_size;

board/freescale/p1_p2_rdb_pc/README

@@ -3,6 +3,7 @@ Overview
 P1_P2_RDB_PC represents a set of boards including
     P1020MSBG-PC
     P1020RDB-PC
+    P1020RDB-PD
     P1020UTM-PC
     P1021RDB-PC
     P1024RDB

board/freescale/p1_p2_rdb_pc/ddr.c

@@ -80,7 +80,7 @@ dimm_params_t ddr_raw_timing = {
 	.refresh_rate_ps = 7800000,
 	.tFAW_ps = 30000,
 };
-#elif defined(CONFIG_P1020MBG)
+#elif (defined(CONFIG_P1020MBG) || defined(CONFIG_P1020RDB_PD))
 /* Micron MT41J512M8_187E */
 dimm_params_t ddr_raw_timing = {
 	.n_ranks = 2,
@@ -111,7 +111,7 @@ dimm_params_t ddr_raw_timing = {
 	.refresh_rate_ps = 7800000,
 	.tFAW_ps = 37500,
 };
-#elif defined(CONFIG_P1020RDB)
+#elif defined(CONFIG_P1020RDB_PC)
 /*
  * Samsung K4B2G0846C-HCF8
  * The following timing are for "downshift"
@@ -251,7 +251,7 @@ phys_size_t fixed_sdram(void)
 
 	ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
 
-	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
 
 	if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
 				ddr_size, LAW_TRGT_IF_DDR_1) < 0) {

board/freescale/p1_p2_rdb_pc/tlb.c

@@ -94,7 +94,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 			MAS3_SX|MAS3_SW|MAS3_SR, 0,
 			0, 8, BOOKE_PAGESZ_1G, 1),
 
-#ifdef CONFIG_P1020MBG
+#if defined(CONFIG_P1020MBG) || defined(CONFIG_P1020RDB_PD)
 	/* 2G DDR on P1020MBG, map the second 1G */
 	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
 			CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,

board/freescale/p1_twr/Makefile

@@ -0,0 +1,35 @@
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+
+include $(TOPDIR)/config.mk
+
+LIB    = $(obj)lib$(BOARD).o
+
+COBJS-y        += $(BOARD).o
+COBJS-y        += ddr.o
+COBJS-y        += law.o
+COBJS-y        += tlb.o
+
+SRCS   := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS   := $(addprefix $(obj),$(COBJS-y))
+SOBJS  := $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/freescale/p1_twr/ddr.c

@@ -0,0 +1,69 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/processor.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/io.h>
+#include <asm/fsl_law.h>
+
+/* Fixed sdram init -- doesn't use serial presence detect. */
+phys_size_t fixed_sdram(void)
+{
+	sys_info_t sysinfo;
+	char buf[32];
+	size_t ddr_size;
+	fsl_ddr_cfg_regs_t ddr_cfg_regs = {
+		.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
+		.cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
+		.cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
+#if CONFIG_CHIP_SELECTS_PER_CTRL > 1
+		.cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS,
+		.cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG,
+		.cs[1].config_2 = CONFIG_SYS_DDR_CS1_CONFIG_2,
+#endif
+		.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3,
+		.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0,
+		.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1,
+		.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2,
+		.ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
+		.ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
+		.ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1,
+		.ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2,
+		.ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
+		.ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL,
+		.ddr_data_init = CONFIG_SYS_DDR_DATA_INIT,
+		.ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL,
+		.ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
+		.ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
+		.timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
+		.timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
+		.ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
+		.ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL,
+		.ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
+		.ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
+		.ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
+	};
+
+	get_sys_info(&sysinfo);
+	printf("Configuring DDR for %s MT/s data rate\n",
+			strmhz(buf, sysinfo.freqDDRBus));
+
+	ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
+
+	if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
+				ddr_size, LAW_TRGT_IF_DDR_1) < 0) {
+		printf("ERROR setting Local Access Windows for DDR\n");
+		return 0;
+	};
+
+	return ddr_size;
+}

board/freescale/p1_twr/law.c

@@ -0,0 +1,16 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_SSD_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC)
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);

board/freescale/p1_twr/p1_twr.c

@@ -0,0 +1,281 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <hwconfig.h>
+#include <pci.h>
+#include <i2c.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/io.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_lbc.h>
+#include <asm/mp.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <ioports.h>
+#include <asm/fsl_serdes.h>
+#include <netdev.h>
+
+#define SYSCLK_64	64000000
+#define SYSCLK_66	66666666
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+	ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	par_io_t *par_io = (par_io_t *) &(gur->qe_par_io);
+	unsigned int cpdat_val = 0;
+
+	/* Set-up up pin muxing based on board switch settings */
+	cpdat_val = par_io[1].cpdat;
+
+	/* Check switch setting for SYSCLK select (PB3)  */
+	if (cpdat_val & 0x10000000)
+		return SYSCLK_64;
+	else
+		return SYSCLK_66;
+
+	return 0;
+}
+
+#ifdef CONFIG_QE
+
+#define PCA_IOPORT_I2C_ADDR		0x23
+#define PCA_IOPORT_OUTPUT_CMD		0x2
+#define PCA_IOPORT_CFG_CMD		0x6
+
+const qe_iop_conf_t qe_iop_conf_tab[] = {
+
+#ifdef CONFIG_TWR_P1025
+	/* GPIO */
+	{1,  0, 1, 0, 0},
+	{1,  18, 1, 0, 0},
+
+	/* GPIO for switch options */
+	{1,  2, 2, 0, 0}, /* PROFIBUS_MODE_SEL */
+	{1,  3, 2, 0, 0}, /* SYS_CLK_SELECT */
+	{1,  29, 2, 0, 0}, /* LOCALBUS_QE_MUXSEL */
+	{1,  30, 2, 0, 0}, /* ETH_TDM_SEL */
+
+	/* QE_MUX_MDC */
+	{1,  19, 1, 0, 1}, /* QE_MUX_MDC */
+
+	/* QE_MUX_MDIO */
+	{1,  20, 3, 0, 1}, /* QE_MUX_MDIO */
+
+	/* UCC_1_MII */
+	{0, 23, 2, 0, 2}, /* CLK12 */
+	{0, 24, 2, 0, 1}, /* CLK9 */
+	{0,  7, 1, 0, 2}, /* ENET1_TXD0_SER1_TXD0 */
+	{0,  9, 1, 0, 2}, /* ENET1_TXD1_SER1_TXD1 */
+	{0, 11, 1, 0, 2}, /* ENET1_TXD2_SER1_TXD2 */
+	{0, 12, 1, 0, 2}, /* ENET1_TXD3_SER1_TXD3 */
+	{0,  6, 2, 0, 2}, /* ENET1_RXD0_SER1_RXD0 */
+	{0, 10, 2, 0, 2}, /* ENET1_RXD1_SER1_RXD1 */
+	{0, 14, 2, 0, 2}, /* ENET1_RXD2_SER1_RXD2 */
+	{0, 15, 2, 0, 2}, /* ENET1_RXD3_SER1_RXD3 */
+	{0,  5, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */
+	{0, 13, 1, 0, 2}, /* ENET1_TX_ER */
+	{0,  4, 2, 0, 2}, /* ENET1_RX_DV_SER1_CTS_B */
+	{0,  8, 2, 0, 2}, /* ENET1_RX_ER_SER1_CD_B */
+	{0, 17, 2, 0, 2}, /* ENET1_CRS */
+	{0, 16, 2, 0, 2}, /* ENET1_COL */
+
+	/* UCC_5_RMII */
+	{1, 11, 2, 0, 1}, /* CLK13 */
+	{1, 7,  1, 0, 2}, /* ENET5_TXD0_SER5_TXD0 */
+	{1, 10, 1, 0, 2}, /* ENET5_TXD1_SER5_TXD1 */
+	{1, 6, 2, 0, 2}, /* ENET5_RXD0_SER5_RXD0 */
+	{1, 9, 2, 0, 2}, /* ENET5_RXD1_SER5_RXD1 */
+	{1, 5, 1, 0, 2}, /* ENET5_TX_EN_SER5_RTS_B */
+	{1, 4, 2, 0, 2}, /* ENET5_RX_DV_SER5_CTS_B */
+	{1, 8, 2, 0, 2}, /* ENET5_RX_ER_SER5_CD_B */
+
+	/* TDMA - clock option is configured in OS based on board setting */
+	{1, 23, 2, 0, 2}, /* TDMA_TXD */
+	{1, 25, 2, 0, 2}, /* TDMA_RXD */
+	{1, 26, 1, 0, 2}, /* TDMA_SYNC */
+#endif
+
+	{0,  0, 0, 0, QE_IOP_TAB_END} /* END of table */
+};
+#endif
+
+int board_early_init_f(void)
+{
+	ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+	setbits_be32(&gur->pmuxcr,
+			(MPC85xx_PMUXCR_SDHC_CD | MPC85xx_PMUXCR_SDHC_WP));
+
+	/* SDHC_DAT[4:7] not exposed to pins (use as SPI) */
+	clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u8 boot_status;
+
+	printf("Board: %s\n", CONFIG_BOARDNAME);
+
+	boot_status = ((gur->porbmsr) >> MPC85xx_PORBMSR_ROMLOC_SHIFT) & 0xf;
+	puts("rom_loc: ");
+	if (boot_status == PORBMSR_ROMLOC_NOR)
+		puts("nor flash");
+	else if (boot_status == PORBMSR_ROMLOC_SDHC)
+		puts("sd");
+	else
+		puts("unknown");
+	puts("\n");
+
+	return 0;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+	fsl_pcie_init_board(0);
+}
+#endif
+
+int board_early_init_r(void)
+{
+	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, /* tlb, epn, rpn */
+		MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,           /* perms, wimge */
+		0, flash_esel, BOOKE_PAGESZ_64M, 1);/* ts, esel, tsize, iprot */
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	struct fsl_pq_mdio_info mdio_info;
+	struct tsec_info_struct tsec_info[4];
+	ccsr_gur_t *gur __attribute__((unused)) =
+		(void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	int num = 0;
+
+#ifdef CONFIG_TSEC1
+	SET_STD_TSEC_INFO(tsec_info[num], 1);
+	num++;
+#endif
+#ifdef CONFIG_TSEC2
+	SET_STD_TSEC_INFO(tsec_info[num], 2);
+	if (is_serdes_configured(SGMII_TSEC2)) {
+		printf("eTSEC2 is in sgmii mode.\n");
+		tsec_info[num].flags |= TSEC_SGMII;
+	}
+	num++;
+#endif
+#ifdef CONFIG_TSEC3
+	SET_STD_TSEC_INFO(tsec_info[num], 3);
+	num++;
+#endif
+
+	if (!num) {
+		printf("No TSECs initialized\n");
+		return 0;
+	}
+
+	mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+	mdio_info.name = DEFAULT_MII_NAME;
+
+	fsl_pq_mdio_init(bis, &mdio_info);
+
+	tsec_eth_init(bis, tsec_info, num);
+
+#if defined(CONFIG_UEC_ETH)
+	/* QE0 and QE3 need to be exposed for UCC1
+	 * and UCC5 Eth mode (in PMUXCR register).
+	 * Currently QE/LBC muxed pins assumed to be
+	 * LBC for U-Boot and PMUXCR updated by OS if required */
+
+	uec_standard_init(bis);
+#endif
+
+	return pci_eth_init(bis);
+}
+
+#if defined(CONFIG_QE)
+static void fdt_board_fixup_qe_pins(void *blob)
+{
+	int node;
+
+	if (!hwconfig("qe")) {
+		/* For QE and eLBC pins multiplexing,
+		 * When don't use QE function, remove
+		 * qe node from dt blob.
+		 */
+		node = fdt_path_offset(blob, "/qe");
+		if (node >= 0)
+			fdt_del_node(blob, node);
+	} else {
+		/* For TWR Peripheral Modules - TWR-SER2
+		 * board only can support Signal Port MII,
+		 * so delete one UEC node when use MII port.
+		 */
+		if (hwconfig("mii"))
+			node = fdt_path_offset(blob, "/qe/ucc@2400");
+		else
+			node = fdt_path_offset(blob, "/qe/ucc@2000");
+		if (node >= 0)
+			fdt_del_node(blob, node);
+	}
+
+	return;
+}
+#endif
+
+#ifdef CONFIG_OF_BOARD_SETUP
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+	FT_FSL_PCI_SETUP;
+
+#ifdef CONFIG_QE
+	do_fixup_by_compat(blob, "fsl,qe", "status", "okay",
+			sizeof("okay"), 0);
+#endif
+#if defined(CONFIG_TWR_P1025)
+	fdt_board_fixup_qe_pins(blob);
+#endif
+	fdt_fixup_dr_usb(blob, bd);
+}
+#endif

board/freescale/p1_twr/tlb.c

@@ -0,0 +1,76 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I,
+			0, 0, BOOKE_PAGESZ_4K, 1),
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 1, BOOKE_PAGESZ_1M, 1),
+
+#ifndef CONFIG_SPL_BUILD
+	/* W**G* - Flash, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+			MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+			0, 2, BOOKE_PAGESZ_64M, 1),
+
+	/* W**G* - Flash, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_SSD_BASE, CONFIG_SYS_SSD_BASE_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 5, BOOKE_PAGESZ_1M, 1),
+
+#ifdef CONFIG_PCI
+	/* *I*G* - PCI memory 1.5G */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI I/O effective: 192K  */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+			MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 4, BOOKE_PAGESZ_256K, 1),
+#endif
+
+#endif
+
+#ifdef CONFIG_SYS_RAMBOOT
+	/* *I*G - eSDHC boot */
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+			MAS3_SX|MAS3_SW|MAS3_SR, 0,
+			0, 8, BOOKE_PAGESZ_1G, 1),
+#endif
+
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);

board/freescale/p2041rdb/p2041rdb.c

@@ -28,7 +28,6 @@ int checkboard(void)
 {
 	u8 sw;
 	struct cpu_type *cpu = gd->arch.cpu;
-	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
 	unsigned int i;
 
 	printf("Board: %sRDB, ", cpu->name);
@@ -39,20 +38,6 @@ int checkboard(void)
 	printf("vBank: %d\n", sw & 0x1);
 
 	/*
-	 * Display the RCW, so that no one gets confused as to what RCW
-	 * we're actually using for this boot.
-	 */
-	puts("Reset Configuration Word (RCW):");
-	for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
-		u32 rcw = in_be32(&gur->rcwsr[i]);
-
-		if ((i % 4) == 0)
-			printf("\n       %08x:", i * 4);
-		printf(" %08x", rcw);
-	}
-	puts("\n");
-
-	/*
 	 * Display the actual SERDES reference clocks as configured by the
 	 * dip switches on the board.  Note that the SWx registers could
 	 * technically be set to force the reference clocks to match the

board/freescale/t4qds/Makefile

@@ -8,7 +8,8 @@ include $(TOPDIR)/config.mk
 
 LIB	= $(obj)lib$(BOARD).o
 
-COBJS-y	+= $(BOARD).o
+COBJS-$(CONFIG_T4240QDS) += t4240qds.o
+COBJS-$(CONFIG_T4240EMU) += t4240emu.o
 COBJS-y	+= ddr.o
 COBJS-$(CONFIG_T4240QDS)+= eth.o
 COBJS-$(CONFIG_PCI)	+= pci.o

board/freescale/t4qds/ddr.c

@@ -13,81 +13,10 @@
 #include <asm/fsl_ddr_sdram.h>
 #include <asm/fsl_ddr_dimm_params.h>
 #include <asm/fsl_law.h>
+#include "ddr.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
-struct board_specific_parameters {
-	u32 n_ranks;
-	u32 datarate_mhz_high;
-	u32 rank_gb;
-	u32 clk_adjust;
-	u32 wrlvl_start;
-	u32 wrlvl_ctl_2;
-	u32 wrlvl_ctl_3;
-	u32 cpo;
-	u32 write_data_delay;
-	u32 force_2T;
-};
-
-/*
- * This table contains all valid speeds we want to override with board
- * specific parameters. datarate_mhz_high values need to be in ascending order
- * for each n_ranks group.
- */
-static const struct board_specific_parameters udimm0[] = {
-	/*
-	 * memory controller 0
-	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
-	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
-	 */
-	{2,  1350, 4, 4,     8, 0x0809090b, 0x0c0c0d0a,   0xff,    2,  0},
-	{2,  1350, 0, 5,     7, 0x0709090b, 0x0c0c0d09,   0xff,    2,  0},
-	{2,  1666, 4, 4,     8, 0x080a0a0d, 0x0d10100b,   0xff,    2,  0},
-	{2,  1666, 0, 5,     7, 0x080a0a0c, 0x0d0d0e0a,   0xff,    2,  0},
-	{2,  1900, 0, 4,     8, 0x090a0b0e, 0x0f11120c,   0xff,    2,  0},
-	{2,  2140, 0, 4,     8, 0x090a0b0e, 0x0f11120c,   0xff,    2,  0},
-	{1,  1350, 0, 5,     8, 0x0809090b, 0x0c0c0d0a,   0xff,    2,  0},
-	{1,  1700, 0, 5,     8, 0x080a0a0c, 0x0c0d0e0a,   0xff,    2,  0},
-	{1,  1900, 0, 4,     8, 0x080a0a0c, 0x0e0e0f0a,   0xff,    2,  0},
-	{1,  2140, 0, 4,     8, 0x090a0b0c, 0x0e0f100b,   0xff,    2,  0},
-	{}
-};
-
-/*
- * The three slots have slightly different timing. The center values are good
- * for all slots. We use identical speed tables for them. In future use, if
- * DIMMs require separated tables, make more entries as needed.
- */
-static const struct board_specific_parameters *udimms[] = {
-	udimm0,
-};
-
-static const struct board_specific_parameters rdimm0[] = {
-	/*
-	 * memory controller 0
-	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
-	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
-	 */
-	{4,  1350, 0, 5,     9, 0x08070605, 0x07080805,   0xff,    2,  0},
-	{4,  1666, 0, 5,     8, 0x08070605, 0x07080805,   0xff,    2,  0},
-	{4,  2140, 0, 5,     8, 0x08070605, 0x07081805,   0xff,    2,  0},
-	{2,  1350, 0, 5,     7, 0x0809090b, 0x0c0c0d09,   0xff,    2,  0},
-	{2,  1666, 0, 5,     8, 0x080a0a0c, 0x0c0d0e0a,   0xff,    2,  0},
-	{2,  2140, 0, 5,     8, 0x090a0b0c, 0x0e0f100b,   0xff,    2,  0},
-	{1,  1350, 0, 5,     8, 0x0809090b, 0x0c0c0d0a,   0xff,    2,  0},
-	{1,  1700, 0, 5,     8, 0x080a0a0c, 0x0c0d0e0a,   0xff,    2,  0},
-	{1,  1900, 0, 4,     8, 0x080a0a0c, 0x0e0e0f0a,   0xff,    2,  0},
-	{1,  2140, 0, 4,     8, 0x090a0b0c, 0x0e0f100b,   0xff,    2,  0},
-	{}
-};
-
-/*
- * The three slots have slightly different timing. See comments above.
- */
-static const struct board_specific_parameters *rdimms[] = {
-	rdimm0,
-};
-
 void fsl_ddr_board_options(memctl_options_t *popts,
 				dimm_params_t *pdimm,
 				unsigned int ctrl_num)

board/freescale/t4qds/ddr.h

@@ -0,0 +1,108 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+struct board_specific_parameters {
+	u32 n_ranks;
+	u32 datarate_mhz_high;
+	u32 rank_gb;
+	u32 clk_adjust;
+	u32 wrlvl_start;
+	u32 wrlvl_ctl_2;
+	u32 wrlvl_ctl_3;
+	u32 cpo;
+	u32 write_data_delay;
+	u32 force_2T;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+
+#ifdef CONFIG_T4240QDS
+static const struct board_specific_parameters udimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
+	 */
+	{2,  1350, 4, 4,     8, 0x0809090b, 0x0c0c0d0a,   0xff,    2,  0},
+	{2,  1350, 0, 5,     7, 0x0709090b, 0x0c0c0d09,   0xff,    2,  0},
+	{2,  1666, 4, 4,     8, 0x080a0a0d, 0x0d10100b,   0xff,    2,  0},
+	{2,  1666, 0, 5,     7, 0x080a0a0c, 0x0d0d0e0a,   0xff,    2,  0},
+	{2,  1900, 0, 4,     8, 0x090a0b0e, 0x0f11120c,   0xff,    2,  0},
+	{2,  2140, 0, 4,     8, 0x090a0b0e, 0x0f11120c,   0xff,    2,  0},
+	{1,  1350, 0, 5,     8, 0x0809090b, 0x0c0c0d0a,   0xff,    2,  0},
+	{1,  1700, 0, 5,     8, 0x080a0a0c, 0x0c0d0e0a,   0xff,    2,  0},
+	{1,  1900, 0, 4,     8, 0x080a0a0c, 0x0e0e0f0a,   0xff,    2,  0},
+	{1,  2140, 0, 4,     8, 0x090a0b0c, 0x0e0f100b,   0xff,    2,  0},
+	{}
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
+	 */
+	{4,  1350, 0, 5,     9, 0x08070605, 0x06070806,   0xff,    2,  0},
+	{4,  1666, 0, 5,    11, 0x0a080706, 0x07090906,   0xff,    2,  0},
+	{4,  2140, 0, 5,    12, 0x0b090807, 0x080a0b07,   0xff,    2,  0},
+	{2,  1350, 0, 5,     9, 0x08070605, 0x06070806,   0xff,    2,  0},
+	{2,  1666, 0, 5,    11, 0x0a090806, 0x08090a06,   0xff,    2,  0},
+	{2,  2140, 0, 5,    12, 0x0b090807, 0x080a0b07,   0xff,    2,  0},
+	{1,  1350, 0, 5,     9, 0x08070605, 0x06070806,   0xff,    2,  0},
+	{1,  1666, 0, 5,    11, 0x0a090806, 0x08090a06,   0xff,    2,  0},
+	{1,  2140, 0, 4,    12, 0x0b090807, 0x080a0b07,   0xff,    2,  0},
+	{}
+};
+
+#else	/* CONFIG_T4240EMU */
+static const struct board_specific_parameters udimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
+	 */
+	{2,  2140, 0, 4,     8, 0x0, 0x0,   0xff,    2,  0},
+	{1,  2140, 0, 4,     8, 0x0, 0x0,   0xff,    2,  0},
+	{}
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3  |      |delay |
+	 */
+	{4,  2140, 0, 5,     8, 0x0, 0x0,   0xff,    2,  0},
+	{2,  2140, 0, 5,     8, 0x0, 0x0,   0xff,    2,  0},
+	{1,  2140, 0, 4,     8, 0x0, 0x0,   0xff,    2,  0},
+	{}
+};
+#endif	/* CONFIG_T4240EMU */
+
+/*
+ * The three slots have slightly different timing. The center values are good
+ * for all slots. We use identical speed tables for them. In future use, if
+ * DIMMs require separated tables, make more entries as needed.
+ */
+static const struct board_specific_parameters *udimms[] = {
+	udimm0,
+};
+
+/*
+ * The three slots have slightly different timing. See comments above.
+ */
+static const struct board_specific_parameters *rdimms[] = {
+	rdimm0,
+};
+
+
+#endif

board/freescale/t4qds/law.c

@@ -19,7 +19,9 @@ struct law_entry law_table[] = {
 #ifdef CONFIG_SYS_QMAN_MEM_PHYS
 	SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
 #endif
+#ifdef QIXIS_BASE_PHYS
 	SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
 #ifdef CONFIG_SYS_DCSRBAR_PHYS
 	/* Limit DCSR to 32M to access NPC Trace Buffer */
 	SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),

board/freescale/t4qds/t4240emu.c

@@ -0,0 +1,80 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	struct cpu_type *cpu = gd->arch.cpu;
+
+	printf("Board: %sEMU\n", cpu->name);
+
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash + PROMJET region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+		MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+	set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+	setup_portals();
+#endif
+
+	return 0;
+}
+
+int misc_init_r(void)
+{
+	return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+	fdt_fixup_liodn(blob);
+	fdt_fixup_dr_usb(blob, bd);
+}

board/freescale/t4qds/t4240qds.c

@@ -43,12 +43,11 @@ int checkboard(void)
 	char buf[64];
 	u8 sw;
 	struct cpu_type *cpu = gd->arch.cpu;
-	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
 	unsigned int i;
 
 	printf("Board: %sQDS, ", cpu->name);
 	printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ",
-		QIXIS_READ(id), QIXIS_READ(arch));
+	       QIXIS_READ(id), QIXIS_READ(arch));
 
 	sw = QIXIS_READ(brdcfg[0]);
 	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
@@ -63,24 +62,11 @@ int checkboard(void)
 		printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
 
 	printf("FPGA: v%d (%s), build %d",
-		(int)QIXIS_READ(scver), qixis_read_tag(buf),
-		(int)qixis_read_minor());
+	       (int)QIXIS_READ(scver), qixis_read_tag(buf),
+	       (int)qixis_read_minor());
 	/* the timestamp string contains "\n" at the end */
 	printf(" on %s", qixis_read_time(buf));
 
-	/* Display the RCW, so that no one gets confused as to what RCW
-	 * we're actually using for this boot.
-	 */
-	puts("Reset Configuration Word (RCW):");
-	for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
-		u32 rcw = in_be32(&gur->rcwsr[i]);
-
-		if ((i % 4) == 0)
-			printf("\n       %08x:", i * 4);
-		printf(" %08x", rcw);
-	}
-	puts("\n");
-
 	/*
 	 * Display the actual SERDES reference clocks as configured by the
 	 * dip switches on the board.  Note that the SWx registers could
@@ -92,7 +78,7 @@ int checkboard(void)
 	puts("SERDES Reference Clocks: ");
 	sw = QIXIS_READ(brdcfg[2]);
 	for (i = 0; i < MAX_SERDES; i++) {
-		static const char *freq[] = {
+		static const char * const freq[] = {
 			"100", "125", "156.25", "161.1328125"};
 		unsigned int clock = (sw >> (6 - 2 * i)) & 3;
 
@@ -430,7 +416,7 @@ int config_backside_crossbar_mux(void)
 		break;
 	default:
 		printf("WARNING: unsupported for SerDes3 Protocol %d\n",
-				srds_prtcl_s3);
+		       srds_prtcl_s3);
 		return -1;
 	}
 
@@ -470,7 +456,7 @@ int config_backside_crossbar_mux(void)
 		break;
 	default:
 		printf("WARNING: unsupported for SerDes4 Protocol %d\n",
-				srds_prtcl_s4);
+		       srds_prtcl_s4);
 		return -1;
 	}
 
@@ -495,8 +481,8 @@ int board_early_init_r(void)
 	disable_tlb(flash_esel);
 
 	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
-			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-			0, flash_esel, BOOKE_PAGESZ_256M, 1);
+		MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		0, flash_esel, BOOKE_PAGESZ_256M, 1);
 
 	set_liodns();
 #ifdef CONFIG_SYS_DPAA_QBMAN
@@ -634,9 +620,8 @@ int misc_init_r(void)
 		u32 pllcr0 = srds_regs->bank[i].pllcr0;
 		u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK;
 		if (expected != actual[i]) {
-			printf("Warning: SERDES%u expects reference clock"
-			       " %sMHz, but actual is %sMHz\n", i + 1,
-			       serdes_clock_to_string(expected),
+			printf("Warning: SERDES%u expects reference clock %sMHz, but actual is %sMHz\n",
+			       i + 1, serdes_clock_to_string(expected),
 			       serdes_clock_to_string(actual[i]));
 		}
 	}
@@ -795,42 +780,44 @@ void qixis_dump_switch(void)
 	}
 
 	sw[0] = dutcfg[0];
-	sw[1] = (dutcfg[1] << 0x07)		| \
-		((dutcfg[12] & 0xC0) >> 1)	| \
-		((dutcfg[11] & 0xE0) >> 3)	| \
-		((dutcfg[6] & 0x80) >> 6)	| \
+	sw[1] = (dutcfg[1] << 0x07)		|
+		((dutcfg[12] & 0xC0) >> 1)	|
+		((dutcfg[11] & 0xE0) >> 3)	|
+		((dutcfg[6] & 0x80) >> 6)	|
 		((dutcfg[1] & 0x80) >> 7);
-	sw[2] = ((brdcfg[1] & 0x0f) << 4)	| \
-		((brdcfg[1] & 0x30) >> 2)	| \
-		((brdcfg[1] & 0x40) >> 5)	| \
+	sw[2] = ((brdcfg[1] & 0x0f) << 4)	|
+		((brdcfg[1] & 0x30) >> 2)	|
+		((brdcfg[1] & 0x40) >> 5)	|
 		((brdcfg[1] & 0x80) >> 7);
 	sw[3] = brdcfg[2];
-	sw[4] = ((dutcfg[2] & 0x01) << 7)	| \
-		((dutcfg[2] & 0x06) << 4)	| \
-		((~QIXIS_READ(present)) & 0x10)	| \
-		((brdcfg[3] & 0x80) >> 4)	| \
-		((brdcfg[3] & 0x01) << 2)	| \
-		((brdcfg[6] == 0x62) ? 3 :	\
-		((brdcfg[6] == 0x5a) ? 2 :	\
+	sw[4] = ((dutcfg[2] & 0x01) << 7)	|
+		((dutcfg[2] & 0x06) << 4)	|
+		((~QIXIS_READ(present)) & 0x10)	|
+		((brdcfg[3] & 0x80) >> 4)	|
+		((brdcfg[3] & 0x01) << 2)	|
+		((brdcfg[6] == 0x62) ? 3 :
+		((brdcfg[6] == 0x5a) ? 2 :
 		((brdcfg[6] == 0x5e) ? 1 : 0)));
-	sw[5] = ((brdcfg[0] & 0x0f) << 4)	| \
-		((QIXIS_READ(rst_ctl) & 0x30) >> 2) | \
+	sw[5] = ((brdcfg[0] & 0x0f) << 4)	|
+		((QIXIS_READ(rst_ctl) & 0x30) >> 2) |
 		((brdcfg[0] & 0x40) >> 5);
 	sw[6] = (brdcfg[11] & 0x20)		|
 		((brdcfg[5] & 0x02) << 3);
-	sw[7] = (((~QIXIS_READ(rst_ctl)) & 0x40) << 1) | \
+	sw[7] = (((~QIXIS_READ(rst_ctl)) & 0x40) << 1) |
 		((brdcfg[5] & 0x10) << 2);
-	sw[8] = ((brdcfg[12] & 0x08) << 4)	| \
+	sw[8] = ((brdcfg[12] & 0x08) << 4)	|
 		((brdcfg[12] & 0x03) << 5);
 
 	puts("DIP switch (reverse-engineering)\n");
 	for (i = 0; i < 9; i++) {
 		printf("SW%d         = 0b%s (0x%02x)\n",
-			i + 1, byte_to_binary_mask(sw[i], mask[i], buf), sw[i]);
+		       i + 1, byte_to_binary_mask(sw[i], mask[i], buf), sw[i]);
 	}
 }
 
-static int do_vdd_adjust(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+static int do_vdd_adjust(cmd_tbl_t *cmdtp,
+			 int flag, int argc,
+			 char * const argv[])
 {
 	ulong override;
 

board/freescale/t4qds/tlb.c

@@ -120,9 +120,11 @@ struct fsl_e_tlb_entry tlb_table[] = {
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 			0, 16, BOOKE_PAGESZ_64K, 1),
 #endif
+#ifdef QIXIS_BASE_PHYS
 	SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 17, BOOKE_PAGESZ_4K, 1),
+#endif
 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 	/*
 	 * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for

boards.cfg

@@ -775,6 +775,8 @@ MPC8569MDS_NAND              powerpc     mpc85xx     mpc8569mds          freesca
 MPC8572DS                    powerpc     mpc85xx     mpc8572ds           freescale      -           MPC8572DS
 MPC8572DS_36BIT              powerpc     mpc85xx     mpc8572ds           freescale      -           MPC8572DS:36BIT
 MPC8572DS_NAND               powerpc     mpc85xx     mpc8572ds           freescale      -           MPC8572DS:NAND
+C29XPCIE                     powerpc     mpc85xx     c29xpcie            freescale      -           C29XPCIE:C29XPCIE,36BIT
+C29XPCIE_SPIFLASH            powerpc     mpc85xx     c29xpcie            freescale      -           C29XPCIE:C29XPCIE,36BIT,SPIFLASH
 P1010RDB_36BIT_NAND          powerpc     mpc85xx     p1010rdb            freescale      -           P1010RDB:P1010RDB,36BIT,NAND
 P1010RDB_36BIT_NAND_SECBOOT  powerpc     mpc85xx     p1010rdb            freescale      -           P1010RDB:P1010RDB,36BIT,NAND_SECBOOT,SECURE_BOOT
 P1010RDB_36BIT_NOR           powerpc     mpc85xx     p1010rdb            freescale      -           P1010RDB:P1010RDB,36BIT
@@ -805,16 +807,20 @@ P1020RDB_36BIT               powerpc     mpc85xx     p1_p2_rdb           freesca
 P1020RDB_36BIT_SDCARD        powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P1020RDB,36BIT,SDCARD
 P1020RDB_36BIT_SPIFLASH      powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P1020RDB,36BIT,SPIFLASH
 P1020RDB_NAND                powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P1020RDB,NAND
-P1020RDB-PC                  powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB
-P1020RDB-PC_36BIT            powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB,36BIT
-P1020RDB-PC_36BIT_NAND       powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB,36BIT,NAND
-P1020RDB-PC_36BIT_SDCARD     powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB,36BIT,SDCARD
-P1020RDB-PC_36BIT_SPIFLASH   powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB,36BIT,SPIFLASH
-P1020RDB-PC_NAND             powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB,NAND
-P1020RDB-PC_SDCARD           powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB,SDCARD
-P1020RDB-PC_SPIFLASH         powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB,SPIFLASH
+P1020RDB-PC                  powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PC
+P1020RDB-PC_36BIT            powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PC,36BIT
+P1020RDB-PC_36BIT_NAND       powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PC,36BIT,NAND
+P1020RDB-PC_36BIT_SDCARD     powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PC,36BIT,SDCARD
+P1020RDB-PC_36BIT_SPIFLASH   powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PC,36BIT,SPIFLASH
+P1020RDB-PC_NAND             powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PC,NAND
+P1020RDB-PC_SDCARD           powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PC,SDCARD
+P1020RDB-PC_SPIFLASH         powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PC,SPIFLASH
 P1020RDB_SDCARD              powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P1020RDB,SDCARD
 P1020RDB_SPIFLASH            powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P1020RDB,SPIFLASH
+P1020RDB-PD                  powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PD
+P1020RDB-PD_NAND             powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PD,NAND
+P1020RDB-PD_SDCARD           powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PD,SDCARD
+P1020RDB-PD_SPIFLASH         powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020RDB_PD,SPIFLASH
 P1020UTM-PC                  powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020UTM
 P1020UTM-PC_36BIT            powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020UTM,36BIT
 P1020UTM-PC_36BIT_SDCARD     powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1020UTM,36BIT,SDCARD
@@ -848,6 +854,7 @@ P1025RDB_36BIT               powerpc     mpc85xx     p1_p2_rdb_pc        freesca
 P1025RDB_NAND                powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1025RDB,NAND
 P1025RDB_SDCARD              powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1025RDB,SDCARD
 P1025RDB_SPIFLASH            powerpc     mpc85xx     p1_p2_rdb_pc        freescale      -           p1_p2_rdb_pc:P1025RDB,SPIFLASH
+TWR-P1025                    powerpc     mpc85xx     p1_twr              freescale      -           p1_twr:TWR_P1025
 P2010RDB                     powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P2010RDB
 P2010RDB_36BIT               powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P2010RDB,36BIT
 P2010RDB_36BIT_SDCARD        powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P2010RDB,36BIT,SDCARD
@@ -924,6 +931,7 @@ stxgp3                       powerpc     mpc85xx     stxgp3              stx
 stxssa                       powerpc     mpc85xx     stxssa              stx            -           stxssa
 stxssa_4M                    powerpc     mpc85xx     stxssa              stx            -           stxssa:STXSSA_4M
 T4240QDS                     powerpc     mpc85xx     t4qds               freescale      -           T4240QDS:PPC_T4240
+T4240EMU                     powerpc     mpc85xx     t4qds               freescale      -           T4240EMU:PPC_T4240
 T4240QDS_SDCARD              powerpc     mpc85xx     t4qds               freescale	-           T4240QDS:PPC_T4240,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
 T4240QDS_SPIFLASH            powerpc     mpc85xx     t4qds               freescale	-           T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
 T4240QDS_SRIO_PCIE_BOOT	     powerpc     mpc85xx     t4qds               freescale      -           T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000

drivers/net/fm/fm.c

@@ -396,6 +396,8 @@ int fm_init_common(int index, struct ccsr_fman *reg)
 	}
 #elif defined(CONFIG_SYS_QE_FMAN_FW_IN_REMOTE)
 	void *addr = (void *)CONFIG_SYS_QE_FMAN_FW_ADDR;
+#else
+	void *addr = NULL;
 #endif
 
 	/* Upload the Fman microcode if it's present */

drivers/pci/fsl_pci_init.c

@@ -28,12 +28,6 @@ DECLARE_GLOBAL_DATA_PTR;
 #include <asm/io.h>
 #include <asm/fsl_pci.h>
 
-/* Freescale-specific PCI config registers */
-#define FSL_PCI_PBFR		0x44
-#define FSL_PCIE_CAP_ID		0x4c
-#define FSL_PCIE_CFG_RDY	0x4b0
-#define FSL_PROG_IF_AGENT	0x1
-
 #ifndef CONFIG_SYS_PCI_MEMORY_BUS
 #define CONFIG_SYS_PCI_MEMORY_BUS 0
 #endif
@@ -424,6 +418,15 @@ void fsl_pci_init(struct pci_controller *hose, struct fsl_pci_info *pci_info)
 	udelay(1);
 #endif
 	if (pcie_cap == PCI_CAP_ID_EXP) {
+		if (block_rev >= PEX_IP_BLK_REV_3_0) {
+#define PEX_CSR0_LTSSM_MASK	0xFC
+#define PEX_CSR0_LTSSM_SHIFT	2
+			ltssm = (in_be32(&pci->pex_csr0)
+				& PEX_CSR0_LTSSM_MASK) >> PEX_CSR0_LTSSM_SHIFT;
+			enabled = (ltssm == 0x11) ? 1 : 0;
+		} else {
+		/* pci_hose_read_config_word(hose, dev, PCI_LTSSM, &ltssm); */
+		/* enabled = ltssm >= PCI_LTSSM_L0; */
 		pci_hose_read_config_word(hose, dev, PCI_LTSSM, &ltssm);
 		enabled = ltssm >= PCI_LTSSM_L0;
 
@@ -456,6 +459,7 @@ void fsl_pci_init(struct pci_controller *hose, struct fsl_pci_info *pci_info)
 					PCI_BASE_ADDRESS_0, pcicsrbar);
 		}
 #endif
+	}
 
 #ifdef CONFIG_SYS_P4080_ERRATUM_PCIE_A003
 		if (enabled == 0) {
@@ -564,6 +568,10 @@ int fsl_is_pci_agent(struct pci_controller *hose)
 		u8 prog_if;
 
 		pci_hose_read_config_byte(hose, dev, PCI_CLASS_PROG, &prog_if);
+		/* Programming Interface (PCI_CLASS_PROG)
+		 * 0 == pci host or pcie root-complex,
+		 * 1 == pci agent or pcie end-point
+		 */
 		return (prog_if == FSL_PROG_IF_AGENT);
 	}
 }

include/configs/B4860QDS.h

@@ -33,7 +33,6 @@
 #define CONFIG_E500MC			/* BOOKE e500mc family */
 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
 #define CONFIG_MPC85xx			/* MPC85xx/PQ3 platform */
-#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MP			/* support multiple processors */
 
 #ifndef CONFIG_SYS_TEXT_BASE
@@ -75,6 +74,13 @@
 #define VSC3308_TX_ADDRESS              0x02
 #define VSC3308_RX_ADDRESS              0x03
 
+/* IDT clock synthesizers */
+#define CONFIG_IDT8T49N222A
+#define I2C_CH_IDT                     0x9
+
+#define IDT_SERDES1_ADDRESS            0x6E
+#define IDT_SERDES2_ADDRESS            0x6C
+
 #define CONFIG_ENV_OVERWRITE
 
 #ifdef CONFIG_SYS_NO_FLASH
@@ -578,6 +584,8 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_SYS_DPAA_FMAN
 
+#define CONFIG_SYS_DPAA_RMAN
+
 /* Default address of microcode for the Linux Fman driver */
 #if defined(CONFIG_SPIFLASH)
 /*

include/configs/BSC9132QDS.h

@@ -224,6 +224,10 @@ combinations. this should be removed later
 
 #define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR
 
+/* DSP CCSRBAR */
+#define CONFIG_SYS_FSL_DSP_CCSRBAR	CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
+#define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS	CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
+
 /*
  * IFC Definitions
  */

include/configs/C29XPCIE.h

@@ -0,0 +1,456 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * C29XPCIE board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_PHYS_64BIT
+
+#ifdef CONFIG_C29XPCIE
+#define CONFIG_PPC_C29X
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RAMBOOT_SPIFLASH
+#define CONFIG_SYS_TEXT_BASE		0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS	0x1107fffc
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE		0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE			/* BOOKE */
+#define CONFIG_E500			/* BOOKE e500 family */
+#define CONFIG_MPC85xx
+#define CONFIG_FSL_IFC			/* Enable IFC Support */
+#define CONFIG_SYS_HAS_SERDES		/* common SERDES init code */
+
+#define CONFIG_PCI			/* Enable PCI/PCIE */
+#ifdef CONFIG_PCI
+#define CONFIG_PCIE1			/* PCIE controler 1 (slot 1) */
+#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_FSL_PCIE_RESET		/* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+
+#define CONFIG_E1000
+
+/*
+ * PCI Windows
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+/* controller 1, Slot 1, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME		"Slot 1"
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc00000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xfffc00000ull
+
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif
+
+#define CONFIG_FSL_LAW			/* Use common FSL init code */
+#define CONFIG_TSEC_ENET
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_DDR_CLK_FREQ	100000000
+#define CONFIG_SYS_CLK_FREQ	66666666
+
+#define CONFIG_HWCONFIG
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+
+#define CONFIG_ADDR_STREAMING		/* toggle addr streaming */
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_ADDR_MAP			1
+#define CONFIG_SYS_NUM_ADDR_MAP		16	/* number of TLB1 entries */
+
+#define CONFIG_SYS_MEMTEST_START	0x00200000
+#define CONFIG_SYS_MEMTEST_END		0x00400000
+#define CONFIG_PANIC_HANG
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR3
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_SPD_BUS_NUM		0
+#define SPD_EEPROM_ADDRESS		0x50
+#define CONFIG_SYS_DDR_RAW_TIMING
+
+/* DDR ECC Setup*/
+#define CONFIG_DDR_ECC
+#define CONFIG_MEM_INIT_VALUE		0xDeadBeef
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+
+#define CONFIG_SYS_SDRAM_SIZE		512
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	1
+
+#define CONFIG_SYS_CCSRBAR		0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
+
+/* Platform SRAM setting  */
+#define CONFIG_SYS_PLATFORM_SRAM_BASE	0xffb00000
+#define CONFIG_SYS_PLATFORM_SRAM_BASE_PHYS \
+			(0xf00000000ull | CONFIG_SYS_PLATFORM_SRAM_BASE)
+#define CONFIG_SYS_PLATFORM_SRAM_SIZE	(512 << 10)
+
+/*
+ * IFC Definitions
+ */
+/* NOR Flash on IFC */
+#define CONFIG_SYS_FLASH_BASE		0xec000000
+#define CONFIG_SYS_MAX_FLASH_SECT	512	/* 64M */
+
+#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE_PHYS }
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* in ms */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* in ms */
+
+/* 16Bit NOR Flash - S29GL512S10TFI01 */
+#define CONFIG_SYS_NOR_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(64*1024*1024)
+#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(4)
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
+				FTIM0_NOR_TEADC(0x5) | \
+				FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x1e) | \
+				FTIM1_NOR_TRAD_NOR(0x0f) | \
+				FTIM1_NOR_TSEQRAD_NOR(0x0f))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
+				FTIM2_NOR_TCH(0x4) | \
+				FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3	0x0
+
+/* CFI for NOR Flash */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE		0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS	0xfff800000ull
+
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+
+/* 8Bit NAND Flash - K9F1G08U0B */
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 \
+				| CSPR_MSEL_NAND \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+#define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */ \
+				| CSOR_NAND_RAL_2	/* RAL = 2 Bytes */ \
+				| CSOR_NAND_PGS_2K	/* Page Size = 2k */ \
+				| CSOR_NAND_SPRZ_64	/* Spare size = 64 */ \
+				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
+#define CONFIG_SYS_NAND_FTIM0	(FTIM0_NAND_TCCST(0x01) | \
+				FTIM0_NAND_TWP(0x0c)   | \
+				FTIM0_NAND_TWCHT(0x08) | \
+				FTIM0_NAND_TWH(0x06))
+#define CONFIG_SYS_NAND_FTIM1	(FTIM1_NAND_TADLE(0x28) | \
+				FTIM1_NAND_TWBE(0x1d)  | \
+				FTIM1_NAND_TRR(0x08)   | \
+				FTIM1_NAND_TRP(0x0c))
+#define CONFIG_SYS_NAND_FTIM2	(FTIM2_NAND_TRAD(0x0c) | \
+				FTIM2_NAND_TREH(0x0a) | \
+				FTIM2_NAND_TWHRE(0x18))
+#define CONFIG_SYS_NAND_FTIM3	(FTIM3_NAND_TWW(0x04))
+
+#define CONFIG_SYS_NAND_DDR_LAW		11
+
+/* Set up IFC registers for boot location NOR/NAND */
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NAND_FTIM3
+
+/* CPLD on IFC, selected by CS2 */
+#define CONFIG_SYS_CPLD_BASE		0xffdf0000
+#define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull \
+					| CONFIG_SYS_CPLD_BASE)
+
+#define CONFIG_SYS_CSPR2	(CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 \
+				| CSPR_MSEL_GPCM \
+				| CSPR_V)
+#define CONFIG_SYS_AMASK2	IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR2	0x0
+/* CPLD Timing parameters for IFC CS2 */
+#define CONFIG_SYS_CS2_FTIM0	(FTIM0_GPCM_TACSE(0x0e) | \
+				FTIM0_GPCM_TEADC(0x0e) | \
+				FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS2_FTIM1	(FTIM1_GPCM_TACO(0x0e) | \
+				FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS2_FTIM2	(FTIM2_GPCM_TCS(0x0e) | \
+				FTIM2_GPCM_TCH(0x0) | \
+				FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS2_FTIM3	0x0
+
+#if defined(CONFIG_RAMBOOT_SPIFLASH)
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_R
+
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000
+#define CONFIG_SYS_INIT_RAM_END		0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END \
+						- GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SERIAL_MULTI		/* Enable both serial ports */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C2_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+
+/* I2C EEPROM */
+/* enable read and write access to EEPROM */
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+#define CONFIG_CMD_I2C
+
+/* eSPI - Enhanced SPI */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_SPI_FLASH_EON
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED		10000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+
+#ifdef CONFIG_TSEC_ENET
+#define CONFIG_NET_MULTI
+#define CONFIG_MII			/* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
+#define CONFIG_TSEC1		1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#define CONFIG_TSEC2		1
+#define CONFIG_TSEC2_NAME	"eTSEC2"
+
+/* Default mode is RGMII mode */
+#define TSEC1_PHY_ADDR		0
+#define TSEC2_PHY_ADDR		2
+
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+
+#define CONFIG_ETHPRIME		"eTSEC1"
+
+#define CONFIG_PHY_GIGE
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_SPIFLASH)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS	0
+#define CONFIG_ENV_SPI_CS	0
+#define CONFIG_ENV_SPI_MAX_HZ	10000000
+#define CONFIG_ENV_SPI_MODE	0
+#define CONFIG_ENV_OFFSET	0x100000	/* 1MB */
+#define CONFIG_ENV_SECT_SIZE	0x10000
+#define CONFIG_ENV_SIZE		0x2000
+#endif
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR	0xfff80000
+#else
+#define CONFIG_ENV_ADDR	(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#endif
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000
+#endif
+
+#define CONFIG_LOADS_ECHO
+#define CONFIG_SYS_LOADS_BAUD_CHANGE
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+						/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* dec freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20) /* Increase max gunzip size */
+
+/*
+ * Environment Configuration
+ */
+
+#ifdef CONFIG_TSEC_ENET
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+#define CONFIG_UBOOTPATH	u-boot.bin/* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY	-1	/* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE		115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"hwconfig=" __stringify(CONFIG_DEF_HWCONFIG)  "\0"	\
+	"netdev=eth0\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
+	"loadaddr=1000000\0"				\
+	"consoledev=ttyS0\0"				\
+	"ramdiskaddr=2000000\0"				\
+	"ramdiskfile=rootfs.ext2.gz.uboot\0"		\
+	"fdtaddr=c00000\0"				\
+	"fdtfile=name/of/device-tree.dtb\0"			\
+	"othbootargs=ramdisk_size=600000\0"		\
+
+#define CONFIG_RAMBOOTCOMMAND			\
+	"setenv bootargs root=/dev/ram rw "	\
+	"console=$consoledev,$baudrate $othbootargs; "	\
+	"tftp $ramdiskaddr $ramdiskfile;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#endif	/* __CONFIG_H */

include/configs/P2041RDB.h

@@ -37,7 +37,6 @@
 #define CONFIG_E500MC			/* BOOKE e500mc family */
 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
 #define CONFIG_MPC85xx			/* MPC85xx/PQ3 platform */
-#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MP			/* support multiple processors */
 
 #ifndef CONFIG_SYS_TEXT_BASE

include/configs/T4240EMU.h

@@ -0,0 +1,170 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * T4240 EMU board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_T4240EMU
+#define CONFIG_PHYS_64BIT
+
+#define CONFIG_SYS_NO_FLASH		1
+#define CONFIG_SYS_FSL_DDR_EMU		1
+#define CONFIG_SYS_FSL_NO_QIXIS		1
+#define CONFIG_SYS_FSL_NO_SERDES	1
+
+#include "t4qds.h"
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_CACHE_FLUSH
+
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_SIZE         0x2000
+
+#define CONFIG_SYS_CLK_FREQ	100000000
+#define CONFIG_DDR_CLK_FREQ	133333333
+#define CONFIG_FSL_TBCLK_EXTRA_DIV 100
+
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_SPD_BUS_NUM	1
+#define SPD_EEPROM_ADDRESS1	0x51
+#define SPD_EEPROM_ADDRESS2	0x52
+#define SPD_EEPROM_ADDRESS3	0x53
+#define SPD_EEPROM_ADDRESS4	0x54
+#define SPD_EEPROM_ADDRESS5	0x55
+#define SPD_EEPROM_ADDRESS6	0x56
+#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1	/* for p3041/p5010 */
+#define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+				+ 0x8000000) | \
+				CSPR_PORT_SIZE_32 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(0)
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x1) | \
+				FTIM0_NOR_TEADC(0x1) | \
+				FTIM0_NOR_TEAHC(0x1))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x1) | \
+				FTIM1_NOR_TRAD_NOR(0x1))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x0) | \
+				FTIM2_NOR_TCH(0x0) | \
+				FTIM2_NOR_TWP(0x1))
+#define CONFIG_SYS_NOR_FTIM3	0x04000000
+#define CONFIG_SYS_IFC_CCR	0x01000000
+
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+
+
+/* I2C */
+#define CONFIG_SYS_FSL_I2C_SPEED	4000000	/* faster speed for emulator */
+#define CONFIG_SYS_FSL_I2C2_SPEED	4000000
+
+/* Qman/Bman */
+#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS	50
+#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS	50
+#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+#define CONFIG_SYS_PMAN
+#define CONFIG_SYS_DPAA_DCE
+#define CONFIG_SYS_DPAA_RMAN
+#define CONFIG_SYS_INTERLAKEN
+
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF40000
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+
+
+
+#define CONFIG_BOOTDELAY	0
+
+/*
+ * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
+ * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
+ * interleaving. It can be cacheline, page, bank, superbank.
+ * See doc/README.fsl-ddr for details.
+ */
+#ifdef CONFIG_PPC_T4240
+#define CTRL_INTLV_PREFERED 3way_4KB
+#else
+#define CTRL_INTLV_PREFERED cacheline
+#endif
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"hwconfig=fsl_ddr:"					\
+	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","	\
+	"bank_intlv=auto;"					\
+	"netdev=eth0\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
+	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"		\
+	"consoledev=ttyS0\0"					\
+	"ramdiskaddr=2000000\0"					\
+	"ramdiskfile=t4240emu/ramdisk.uboot\0"			\
+	"fdtaddr=c00000\0"					\
+	"fdtfile=t4240emu/t4240emu.dtb\0"				\
+	"bdev=sda3\0"						\
+	"c=ffe\0"
+
+/*
+ * For emulation this causes u-boot to jump to the start of the proof point
+ * app code automatically
+ */
+#define CONFIG_PROOF_POINTS			\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"cpu 1 release 0x29000000 - - -;"		\
+	"cpu 2 release 0x29000000 - - -;"		\
+	"cpu 3 release 0x29000000 - - -;"		\
+	"cpu 4 release 0x29000000 - - -;"		\
+	"cpu 5 release 0x29000000 - - -;"		\
+	"cpu 6 release 0x29000000 - - -;"		\
+	"cpu 7 release 0x29000000 - - -;"		\
+	"go 0x29000000"
+
+#define CONFIG_HVBOOT				\
+	"setenv bootargs config-addr=0x60000000; "	\
+	"bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_LINUX					\
+	"errata;"					\
+	"setenv othbootargs ignore_loglevel;"		\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"setenv ramdiskaddr 0x02000000;"		\
+	"setenv fdtaddr 0x00c00000;"			\
+	"setenv loadaddr 0x1000000;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_LINUX
+
+#endif	/* __CONFIG_H */

include/configs/T4240QDS.h

@@ -7,6 +7,9 @@
 /*
  * T4240 QDS board configuration file
  */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
 #define CONFIG_T4240QDS
 #define CONFIG_PHYS_64BIT
 
@@ -15,4 +18,543 @@
 
 #define CONFIG_ICS307_REFCLK_HZ		25000000  /* ICS307 ref clk freq */
 
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
+#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg
+#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg
+#endif
+
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+/* Set 1M boot space */
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
+#define CONFIG_DDR_ECC
+
 #include "t4qds.h"
+
+#ifdef CONFIG_SYS_NO_FLASH
+#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS              0
+#define CONFIG_ENV_SPI_CS               0
+#define CONFIG_ENV_SPI_MAX_HZ           10000000
+#define CONFIG_ENV_SPI_MODE             0
+#define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
+#define CONFIG_ENV_SECT_SIZE            0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV          0
+#define CONFIG_ENV_SIZE			0x2000
+#define CONFIG_ENV_OFFSET		(512 * 1097)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR		0xffe20000
+#define CONFIG_ENV_SIZE		0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE		0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk()
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM	0
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_SPD_BUS_NUM	0
+#define SPD_EEPROM_ADDRESS1	0x51
+#define SPD_EEPROM_ADDRESS2	0x52
+#define SPD_EEPROM_ADDRESS3	0x53
+#define SPD_EEPROM_ADDRESS4	0x54
+#define SPD_EEPROM_ADDRESS5	0x55
+#define SPD_EEPROM_ADDRESS6	0x56
+#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1	/* for p3041/p5010 */
+#define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+				+ 0x8000000) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
+
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
+				FTIM0_NOR_TEADC(0x5) | \
+				FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
+				FTIM1_NOR_TRAD_NOR(0x1A) |\
+				FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
+				FTIM2_NOR_TCH(0x4) | \
+				FTIM2_NOR_TWPH(0x0E) | \
+				FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3	0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS \
+					+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+
+#define CONFIG_FSL_QIXIS	/* use common QIXIS code */
+#define QIXIS_BASE			0xffdf0000
+#define QIXIS_LBMAP_SWITCH		6
+#define QIXIS_LBMAP_MASK		0x0f
+#define QIXIS_LBMAP_SHIFT		0
+#define QIXIS_LBMAP_DFLTBANK		0x00
+#define QIXIS_LBMAP_ALTBANK		0x04
+#define QIXIS_RST_CTL_RESET		0x83
+#define QIXIS_RST_FORCE_MEM		0x1
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
+#define QIXIS_BASE_PHYS		(0xf00000000ull | QIXIS_BASE)
+
+#define CONFIG_SYS_CSPR3_EXT	(0xf)
+#define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 \
+				| CSPR_MSEL_GPCM \
+				| CSPR_V)
+#define CONFIG_SYS_AMASK3	IFC_AMASK(4*1024)
+#define CONFIG_SYS_CSOR3	0x0
+/* QIXIS Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
+					FTIM1_GPCM_TRAD(0x3f))
+#define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
+					FTIM2_GPCM_TCH(0x0) | \
+					FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS3_FTIM3		0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE		0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
+				| CSOR_NAND_RAL_3	/* RAL = 2Byes */ \
+				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
+				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x07) | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0x0e)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
+					FTIM2_NAND_TREH(0x0a) | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW		11
+
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
+#endif
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+
+/* I2C */
+#define CONFIG_SYS_FSL_I2C_SPEED	100000	/* I2C speed */
+#define CONFIG_SYS_FSL_I2C2_SPEED	100000	/* I2C2 speed */
+#define I2C_MUX_PCA_ADDR_PRI		0x77 /* I2C bus multiplexer,primary */
+#define I2C_MUX_PCA_ADDR_SEC		0x76 /* I2C bus multiplexer,secondary */
+
+#define I2C_MUX_CH_DEFAULT	0x8
+#define I2C_MUX_CH_VOL_MONITOR	0xa
+#define I2C_MUX_CH_VSC3316_FS	0xc
+#define I2C_MUX_CH_VSC3316_BS	0xd
+
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR		0x40
+#define I2C_VOL_MONITOR_BUS_V_OFFSET	0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF	0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT	3
+
+/* VSC Crossbar switches */
+#define CONFIG_VSC_CROSSBAR
+#define VSC3316_FSM_TX_ADDR	0x70
+#define VSC3316_FSM_RX_ADDR	0x71
+
+/*
+ * RapidIO
+ */
+
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000	/* 512K */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000	/* 256K */
+
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/*
+ * SRIO_PCIE_BOOT - SLAVE
+ */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+#endif
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED         10000000
+#define CONFIG_SF_DEFAULT_MODE          0
+
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS	50
+#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS	50
+#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+#define CONFIG_SYS_PMAN
+#define CONFIG_SYS_DPAA_DCE
+#define CONFIG_SYS_DPAA_RMAN
+#define CONFIG_SYS_INTERLAKEN
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 545KB (1089 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF40000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_TERANETICS
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+#define FM1_10GEC1_PHY_ADDR	0x0
+#define FM1_10GEC2_PHY_ADDR	0x1
+#define FM2_10GEC1_PHY_ADDR	0x2
+#define FM2_10GEC2_PHY_ADDR	0x3
+#endif
+
+
+/* SATA */
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CONFIG_SYS_SATA_MAX_DEVICE	2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
+
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"FM1@DTSEC1"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+#endif
+
+/*
+* USB
+*/
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#define CONFIG_HAS_FSL_DR_USB
+
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+#define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */
+
+#define __USB_PHY_TYPE	utmi
+
+/*
+ * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
+ * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
+ * interleaving. It can be cacheline, page, bank, superbank.
+ * See doc/README.fsl-ddr for details.
+ */
+#ifdef CONFIG_PPC_T4240
+#define CTRL_INTLV_PREFERED 3way_4KB
+#else
+#define CTRL_INTLV_PREFERED cacheline
+#endif
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"hwconfig=fsl_ddr:"					\
+	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","	\
+	"bank_intlv=auto;"					\
+	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+	"netdev=eth0\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
+	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"		\
+	"tftpflash=tftpboot $loadaddr $uboot && "		\
+	"protect off $ubootaddr +$filesize && "			\
+	"erase $ubootaddr +$filesize && "			\
+	"cp.b $loadaddr $ubootaddr $filesize && "		\
+	"protect on $ubootaddr +$filesize && "			\
+	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
+	"consoledev=ttyS0\0"					\
+	"ramdiskaddr=2000000\0"					\
+	"ramdiskfile=t4240qds/ramdisk.uboot\0"			\
+	"fdtaddr=c00000\0"					\
+	"fdtfile=t4240qds/t4240qds.dtb\0"				\
+	"bdev=sda3\0"						\
+	"c=ffe\0"
+
+#define CONFIG_HVBOOT				\
+	"setenv bootargs config-addr=0x60000000; "	\
+	"bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_ALU				\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"cpu 1 release 0x01000000 - - -;"		\
+	"cpu 2 release 0x01000000 - - -;"		\
+	"cpu 3 release 0x01000000 - - -;"		\
+	"cpu 4 release 0x01000000 - - -;"		\
+	"cpu 5 release 0x01000000 - - -;"		\
+	"cpu 6 release 0x01000000 - - -;"		\
+	"cpu 7 release 0x01000000 - - -;"		\
+	"go 0x01000000"
+
+#define CONFIG_LINUX				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"setenv ramdiskaddr 0x02000000;"		\
+	"setenv fdtaddr 0x00c00000;"			\
+	"setenv loadaddr 0x1000000;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT					\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND			\
+	"setenv bootargs root=/dev/nfs rw "	\
+	"nfsroot=$serverip:$rootpath "		\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $ramdiskaddr $ramdiskfile;"		\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif	/* __CONFIG_H */

include/configs/corenet_ds.h

@@ -42,7 +42,6 @@
 #define CONFIG_E500MC			/* BOOKE e500mc family */
 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
 #define CONFIG_MPC85xx			/* MPC85xx/PQ3 platform */
-#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MP			/* support multiple processors */
 
 #ifndef CONFIG_SYS_TEXT_BASE

include/configs/p1_p2_rdb_pc.h

@@ -34,7 +34,7 @@
 #define CONFIG_SYS_L2_SIZE	(256 << 10)
 #endif
 
-#if defined(CONFIG_P1020RDB)
+#if defined(CONFIG_P1020RDB_PC)
 #define CONFIG_BOARDNAME "P1020RDB-PC"
 #define CONFIG_NAND_FSL_ELBC
 #define CONFIG_P1020
@@ -50,6 +50,35 @@
 #define CONFIG_SYS_L2_SIZE	(256 << 10)
 #endif
 
+/*
+ * P1020RDB-PD board has user selectable switches for evaluating different
+ * frequency and boot options for the P1020 device. The table that
+ * follow describe the available options. The front six binary number was in
+ * accordance with SW3[1:6].
+ * 111101 533 533 267 667 NOR Core0 boot; Core1 hold-off
+ * 101101 667 667 333 667 NOR Core0 boot; Core1 hold-off
+ * 011001 800 800 400 667 NOR Core0 boot; Core1 hold-off
+ * 001001 800 800 400 667 SD/MMC Core0 boot; Core1 hold-off
+ * 001101 800 800 400 667 SPI Core0 boot; Core1 hold-off
+ * 010001 800 800 400 667 NAND Core0 boot; Core1 hold-off
+ * 011101 800 800 400 667 PCIe-2 Core0 boot; Core1 hold-off
+ */
+#if defined(CONFIG_P1020RDB_PD)
+#define CONFIG_BOARDNAME "P1020RDB-PD"
+#define CONFIG_NAND_FSL_ELBC
+#define CONFIG_P1020
+#define CONFIG_SPI_FLASH
+#define CONFIG_VSC7385_ENET
+#define CONFIG_SLIC
+#define __SW_BOOT_MASK		0x03
+#define __SW_BOOT_NOR		0x64
+#define __SW_BOOT_SPI		0x34
+#define __SW_BOOT_SD		0x24
+#define __SW_BOOT_NAND		0x44
+#define __SW_BOOT_PCIE		0x74
+#define CONFIG_SYS_L2_SIZE	(256 << 10)
+#endif
+
 #if defined(CONFIG_P1021RDB)
 #define CONFIG_BOARDNAME "P1021RDB-PC"
 #define CONFIG_NAND_FSL_ELBC
@@ -259,7 +288,7 @@
 #define SPD_EEPROM_ADDRESS 0x52
 #undef CONFIG_FSL_DDR_INTERACTIVE
 
-#ifdef CONFIG_P1020MBG
+#if (defined(CONFIG_P1020MBG) || defined(CONFIG_P1020RDB_PD))
 #define CONFIG_SYS_SDRAM_SIZE_LAW	LAW_SIZE_2G
 #define CONFIG_CHIP_SELECTS_PER_CTRL	2
 #else
@@ -330,7 +359,7 @@
 /*
  * Local Bus Definitions
  */
-#if defined(CONFIG_P1020MBG)
+#if (defined(CONFIG_P1020MBG) || defined(CONFIG_P1020RDB_PD))
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* 64M */
 #define CONFIG_SYS_FLASH_BASE		0xec000000
 #elif defined(CONFIG_P1020UTM)
@@ -381,13 +410,27 @@
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_CMD_NAND
+#if defined(CONFIG_P1020RDB_PD)
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+#else
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(16 * 1024)
+#endif
 
 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 	| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
 	| BR_PS_8	/* Port Size = 8 bit */ \
 	| BR_MS_FCM	/* MSEL = FCM */ \
 	| BR_V)	/* valid */
+#if defined(CONFIG_P1020RDB_PD)
+#define CONFIG_SYS_NAND_OR_PRELIM	(OR_AM_32KB \
+	| OR_FCM_PGS	/* Large Page*/ \
+	| OR_FCM_CSCT \
+	| OR_FCM_CST \
+	| OR_FCM_CHT \
+	| OR_FCM_SCY_1 \
+	| OR_FCM_TRLX \
+	| OR_FCM_EHTR)
+#else
 #define CONFIG_SYS_NAND_OR_PRELIM	(OR_AM_32KB	/* small page */ \
 	| OR_FCM_CSCT \
 	| OR_FCM_CST \
@@ -395,6 +438,7 @@
 	| OR_FCM_SCY_1 \
 	| OR_FCM_TRLX \
 	| OR_FCM_EHTR)
+#endif
 #endif /* CONFIG_NAND_FSL_ELBC */
 
 #define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */

include/configs/p1_twr.h

@@ -0,0 +1,619 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * QorIQ P1 Tower boards configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#if defined(CONFIG_TWR_P1025)
+#define CONFIG_BOARDNAME "TWR-P1025"
+#define CONFIG_P1025
+#define CONFIG_PHY_ATHEROS
+#define CONFIG_QE
+#define CONFIG_SYS_LBC_LBCR	0x00080000	/* Conversion of LBC addr */
+#define CONFIG_SYS_LBC_LCRR	0x80000002	/* LB clock ratio reg */
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RAMBOOT_SDCARD
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE		0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS	0x1107fffc
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE		0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500
+#define CONFIG_MPC85xx
+
+#define CONFIG_MP
+
+#define CONFIG_FSL_ELBC
+#define CONFIG_PCI
+#define CONFIG_PCIE1	/* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2	/* PCIE controler 2 (slot 2) */
+#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
+#define CONFIG_FSL_PCIE_RESET	/* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
+
+#define CONFIG_FSL_LAW
+#define CONFIG_TSEC_ENET	/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_CMD_SATA
+#define CONFIG_SATA_SIL3114
+#define CONFIG_SYS_SATA_MAX_DEVICE	2
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /*sysclk for TWR-P1025 */
+
+#define CONFIG_DDR_CLK_FREQ	66666666
+
+#define CONFIG_HWCONFIG
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE
+#define CONFIG_BTB
+
+#define CONFIG_BOARD_EARLY_INIT_F	/* Call board_pre_init */
+
+#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x1fffffff
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+#define CONFIG_SYS_CCSRBAR		0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR3
+
+#define CONFIG_SYS_SDRAM_SIZE_LAW	LAW_SIZE_512M
+#define CONFIG_CHIP_SELECTS_PER_CTRL	1
+
+#define CONFIG_SYS_SDRAM_SIZE		(1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+
+/* Default settings for DDR3 */
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000001f
+#define CONFIG_SYS_DDR_CS0_CONFIG	0x80014202
+#define CONFIG_SYS_DDR_CS0_CONFIG_2	0x00000000
+#define CONFIG_SYS_DDR_CS1_BNDS		0x00000000
+#define CONFIG_SYS_DDR_CS1_CONFIG	0x00000000
+#define CONFIG_SYS_DDR_CS1_CONFIG_2	0x00000000
+
+#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
+#define CONFIG_SYS_DDR_INIT_ADDR	0x00000000
+#define CONFIG_SYS_DDR_INIT_EXT_ADDR	0x00000000
+#define CONFIG_SYS_DDR_MODE_CONTROL	0x00000000
+
+#define CONFIG_SYS_DDR_ZQ_CONTROL	0x89080600
+#define CONFIG_SYS_DDR_WRLVL_CONTROL	0x8655a608
+#define CONFIG_SYS_DDR_SR_CNTR		0x00000000
+#define CONFIG_SYS_DDR_RCW_1		0x00000000
+#define CONFIG_SYS_DDR_RCW_2		0x00000000
+#define CONFIG_SYS_DDR_CONTROL		0xc70c0000	/* Type = DDR3	*/
+#define CONFIG_SYS_DDR_CONTROL_2	0x04401050
+#define CONFIG_SYS_DDR_TIMING_4		0x00220001
+#define CONFIG_SYS_DDR_TIMING_5		0x03402400
+
+#define CONFIG_SYS_DDR_TIMING_3		0x00020000
+#define CONFIG_SYS_DDR_TIMING_0		0x00220004
+#define CONFIG_SYS_DDR_TIMING_1		0x5c5b6544
+#define CONFIG_SYS_DDR_TIMING_2		0x0fa880de
+#define CONFIG_SYS_DDR_CLK_CTRL		0x03000000
+#define CONFIG_SYS_DDR_MODE_1		0x80461320
+#define CONFIG_SYS_DDR_MODE_2		0x00008000
+#define CONFIG_SYS_DDR_INTERVAL		0x09480000
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000 0x1fff_ffff	DDR		Up to 512MB cacheable
+ * 0x8000_0000 0xdfff_ffff	PCI Express Mem	1.5G non-cacheable(PCIe * 3)
+ * 0xffc0_0000 0xffc3_ffff	PCI IO range	256k non-cacheable
+ *
+ * Localbus
+ * 0xe000_0000 0xe002_0000	SSD1289		128K non-cacheable
+ * 0xec00_0000 0xefff_ffff	FLASH		Up to 64M non-cacheable
+ *
+ * 0xff90_0000 0xff97_ffff	L2 SRAM		Up to 512K cacheable
+ * 0xffd0_0000 0xffd0_3fff	init ram	16K Cacheable
+ * 0xffe0_0000 0xffef_ffff	CCSR		1M non-cacheable
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CONFIG_SYS_MAX_FLASH_SECT	512	/* 64M */
+#define CONFIG_SYS_FLASH_BASE		0xec000000
+
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS)) \
+	| BR_PS_16 | BR_V)
+
+#define CONFIG_FLASH_OR_PRELIM	0xfc0000b1
+
+#define CONFIG_SYS_SSD_BASE	0xe0000000
+#define CONFIG_SYS_SSD_BASE_PHYS	CONFIG_SYS_SSD_BASE
+#define CONFIG_SSD_BR_PRELIM	(BR_PHYS_ADDR(CONFIG_SYS_SSD_BASE_PHYS) | \
+					BR_PS_16 | BR_V)
+#define CONFIG_SSD_OR_PRELIM	(OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
+				 OR_GPCM_ACS_DIV2 | OR_GPCM_SCY | \
+				 OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+
+#define CONFIG_SYS_BR2_PRELIM CONFIG_SSD_BR_PRELIM
+#define CONFIG_SYS_OR2_PRELIM CONFIG_SSD_OR_PRELIM
+
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000
+/* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS	CONFIG_SYS_INIT_RAM_ADDR
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+/* Size of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)/* Reserve 512 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN	(1024 * 1024)/* Reserved for malloc */
+
+#define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
+#define CONFIG_SYS_OR0_PRELIM	CONFIG_FLASH_OR_PRELIM	/* NOR Options */
+
+/* Serial Port
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX		1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+#define CONFIG_SYS_64BIT_VSPRINTF
+#define CONFIG_SYS_64BIT_STRTOUL
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL			/* Use FSL common I2C driver */
+#define CONFIG_SYS_FSL_I2C_SPEED	400000	/* I2C spd and slave address */
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52
+
+/*
+ * I2C2 EEPROM
+ */
+#define CONFIG_SYS_FSL_I2C2_SPEED	400000	/* I2C spd and slave address */
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+
+#define CONFIG_SYS_I2C_PCA9555_ADDR	0x23
+
+/* enable read and write access to EEPROM */
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_HARD_SPI
+#define CONFIG_FSL_ESPI
+
+#if defined(CONFIG_PCI)
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 2, direct to uli, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME		"TWR-ELEV PCIe SLOT"
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 1, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME		"mini PCIe SLOT"
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc00000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc00000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP	/* do pci plug-and-play */
+#define CONFIG_E1000	/* Defind e1000 pci Ethernet card*/
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+
+#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_PCI */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI
+#endif
+
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#undef CONFIG_TSEC2
+#undef CONFIG_TSEC2_NAME
+#define CONFIG_TSEC3
+#define CONFIG_TSEC3_NAME	"eTSEC3"
+
+#define TSEC1_PHY_ADDR	2
+#define TSEC2_PHY_ADDR	0
+#define TSEC3_PHY_ADDR	1
+
+#define TSEC1_FLAGS	(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS	(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS	(TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX	0
+#define TSEC2_PHYIDX	0
+#define TSEC3_PHYIDX	0
+
+#define CONFIG_ETHPRIME	"eTSEC1"
+
+#define CONFIG_PHY_GIGE	1	/* Include GbE speed/duplex detection */
+
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#undef CONFIG_HAS_ETH2
+#endif /* CONFIG_TSEC_ENET */
+
+#ifdef CONFIG_QE
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xefec0000
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#endif /* CONFIG_QE */
+
+#ifdef CONFIG_TWR_P1025
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_MIIM_ADDRESS	(CONFIG_SYS_CCSRBAR + 0x82120)
+
+#undef CONFIG_UEC_ETH
+#define CONFIG_PHY_MODE_NEED_CHANGE
+
+#define CONFIG_UEC_ETH1	/* ETH1 */
+#define CONFIG_HAS_ETH0
+
+#ifdef CONFIG_UEC_ETH1
+#define CONFIG_SYS_UEC1_UCC_NUM	0	/* UCC1 */
+#define CONFIG_SYS_UEC1_RX_CLK	QE_CLK12 /* CLK12 for MII */
+#define CONFIG_SYS_UEC1_TX_CLK	QE_CLK9 /* CLK9 for MII */
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	0x18	/* 0x18 for MII */
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
+#endif /* CONFIG_UEC_ETH1 */
+
+#define CONFIG_UEC_ETH5	/* ETH5 */
+#define CONFIG_HAS_ETH1
+
+#ifdef CONFIG_UEC_ETH5
+#define CONFIG_SYS_UEC5_UCC_NUM	4	/* UCC5 */
+#define CONFIG_SYS_UEC5_RX_CLK	QE_CLK_NONE
+#define CONFIG_SYS_UEC5_TX_CLK	QE_CLK13 /* CLK 13 for RMII */
+#define CONFIG_SYS_UEC5_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC5_PHY_ADDR	0x19	/* 0x19 for RMII */
+#define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC5_INTERFACE_SPEED	100
+#endif /* CONFIG_UEC_ETH5 */
+#endif /* CONFIG_TWR-P1025 */
+
+/*
+ * Environment
+ */
+#ifdef CONFIG_SYS_RAMBOOT
+#ifdef CONFIG_RAMBOOT_SDCARD
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_SYS_MMC_ENV_DEV	0
+#else
+#define CONFIG_ENV_IS_NOWHERE	/* Store ENV in memory only */
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE		0x2000
+#endif
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR	0xfff80000
+#else
+#define CONFIG_ENV_ADDR	(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#endif
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+/*
+ * USB
+ */
+#define CONFIG_HAS_FSL_DR_USB
+
+#if defined(CONFIG_HAS_FSL_DR_USB)
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#endif
+#endif
+
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#endif
+
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
+		 || defined(CONFIG_FSL_SATA)
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+#undef CONFIG_WATCHDOG	/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000	/* decrementer freq: 1ms tick */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_HOSTNAME		unknown
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+#define CONFIG_UBOOTPATH	u-boot.bin /* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR	1000000
+
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+#define CONFIG_BOOTARGS	/* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS	\
+"netdev=eth0\0"	\
+"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"	\
+"loadaddr=1000000\0"	\
+"bootfile=uImage\0"	\
+"dtbfile=twr-p1025twr.dtb\0"	\
+"ramdiskfile=rootfs.ext2.gz.uboot\0"	\
+"qefirmwarefile=fsl_qe_ucode_1021_10_A.bin\0"	\
+"tftpflash=tftpboot $loadaddr $uboot; "	\
+	"protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+	"erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
+	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \
+	"protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
+	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
+"kernelflash=tftpboot $loadaddr $bootfile; "	\
+	"protect off 0xefa80000 +$filesize; "	\
+	"erase 0xefa80000 +$filesize; "	\
+	"cp.b $loadaddr 0xefa80000 $filesize; "	\
+	"protect on 0xefa80000 +$filesize; "	\
+	"cmp.b $loadaddr 0xefa80000 $filesize\0"	\
+"dtbflash=tftpboot $loadaddr $dtbfile; "	\
+	"protect off 0xefe80000 +$filesize; "	\
+	"erase 0xefe80000 +$filesize; "	\
+	"cp.b $loadaddr 0xefe80000 $filesize; "	\
+	"protect on 0xefe80000 +$filesize; "	\
+	"cmp.b $loadaddr 0xefe80000 $filesize\0"	\
+"ramdiskflash=tftpboot $loadaddr $ramdiskfile; "	\
+	"protect off 0xeeb80000 +$filesize; "	\
+	"erase 0xeeb80000 +$filesize; "	\
+	"cp.b $loadaddr 0xeeb80000 $filesize; "	\
+	"protect on 0xeeb80000 +$filesize; "	\
+	"cmp.b $loadaddr 0xeeb80000 $filesize\0"	\
+"qefirmwareflash=tftpboot $loadaddr $qefirmwarefile; "	\
+	"protect off 0xefec0000 +$filesize; "	\
+	"erase 0xefec0000 +$filesize; "	\
+	"cp.b $loadaddr 0xefec0000 $filesize; "	\
+	"protect on 0xefec0000 +$filesize; "	\
+	"cmp.b $loadaddr 0xefec0000 $filesize\0"	\
+"consoledev=ttyS0\0"	\
+"ramdiskaddr=2000000\0"	\
+"ramdiskfile=rootfs.ext2.gz.uboot\0"	\
+"fdtaddr=c00000\0"	\
+"bdev=sda1\0"	\
+"norbootaddr=ef080000\0"	\
+"norfdtaddr=ef040000\0"	\
+"ramdisk_size=120000\0" \
+"usbboot=setenv bootargs root=/dev/sda1 rw rootdelay=5 " \
+"console=$consoledev,$baudrate $othbootargs ; bootm 0xefa80000 - 0xefe80000"
+
+#define CONFIG_NFSBOOTCOMMAND	\
+"setenv bootargs root=/dev/nfs rw "	\
+"nfsroot=$serverip:$rootpath "	\
+"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+"console=$consoledev,$baudrate $othbootargs;" \
+"tftp $loadaddr $bootfile&&"	\
+"tftp $fdtaddr $fdtfile&&"	\
+"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_HDBOOT	\
+"setenv bootargs root=/dev/$bdev rw rootdelay=30 "	\
+"console=$consoledev,$baudrate $othbootargs;" \
+"usb start;"	\
+"ext2load usb 0:1 $loadaddr /boot/$bootfile;"	\
+"ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"	\
+"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_USB_FAT_BOOT	\
+"setenv bootargs root=/dev/ram rw "	\
+"console=$consoledev,$baudrate $othbootargs " \
+"ramdisk_size=$ramdisk_size;"	\
+"usb start;"	\
+"fatload usb 0:2 $loadaddr $bootfile;"	\
+"fatload usb 0:2 $fdtaddr $fdtfile;"	\
+"fatload usb 0:2 $ramdiskaddr $ramdiskfile;"	\
+"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_USB_EXT2_BOOT	\
+"setenv bootargs root=/dev/ram rw "	\
+"console=$consoledev,$baudrate $othbootargs " \
+"ramdisk_size=$ramdisk_size;"	\
+"usb start;"	\
+"ext2load usb 0:4 $loadaddr $bootfile;"	\
+"ext2load usb 0:4 $fdtaddr $fdtfile;" \
+"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
+"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_NORBOOT	\
+"setenv bootargs root=/dev/mtdblock3 rw "	\
+"console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"	\
+"bootm $norbootaddr - $norfdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND_TFTP	\
+"setenv bootargs root=/dev/ram rw "	\
+"console=$consoledev,$baudrate $othbootargs " \
+"ramdisk_size=$ramdisk_size;"	\
+"tftp $ramdiskaddr $ramdiskfile;"	\
+"tftp $loadaddr $bootfile;"	\
+"tftp $fdtaddr $fdtfile;"	\
+"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND	\
+"setenv bootargs root=/dev/ram rw "	\
+"console=$consoledev,$baudrate $othbootargs " \
+"ramdisk_size=$ramdisk_size;"	\
+"bootm 0xefa80000 0xeeb80000 0xefe80000"
+
+#define CONFIG_BOOTCOMMAND	CONFIG_RAMBOOTCOMMAND
+
+#endif /* __CONFIG_H */

include/configs/t4qds.h

@@ -7,24 +7,8 @@
 /*
  * Corenet DS style board configuration file
  */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
-#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg
-#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg
-#endif
-
-#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
-/* Set 1M boot space */
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
-		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#define CONFIG_SYS_NO_FLASH
-#endif
+#ifndef __T4QDS_H
+#define __T4QDS_H
 
 #define CONFIG_CMD_REGINFO
 
@@ -34,7 +18,6 @@
 #define CONFIG_E500MC			/* BOOKE e500mc family */
 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
 #define CONFIG_MPC85xx			/* MPC85xx/PQ3 platform */
-#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
 #define CONFIG_MP			/* support multiple processors */
 
 #ifndef CONFIG_SYS_TEXT_BASE
@@ -58,70 +41,16 @@
 #define CONFIG_SYS_SRIO
 #define CONFIG_SRIO1			/* SRIO port 1 */
 #define CONFIG_SRIO2			/* SRIO port 2 */
-#define CONFIG_SRIO_PCIE_BOOT_MASTER
 
 #define CONFIG_FSL_LAW			/* Use common FSL init code */
 
 #define CONFIG_ENV_OVERWRITE
 
-#ifdef CONFIG_SYS_NO_FLASH
-#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_ENV_IS_NOWHERE
-#endif
-#else
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#endif
-
-#if defined(CONFIG_SPIFLASH)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS              0
-#define CONFIG_ENV_SPI_CS               0
-#define CONFIG_ENV_SPI_MAX_HZ           10000000
-#define CONFIG_ENV_SPI_MODE             0
-#define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
-#define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
-#define CONFIG_ENV_SECT_SIZE            0x10000
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_SYS_MMC_ENV_DEV          0
-#define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_OFFSET		(512 * 1097)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-#define CONFIG_ENV_IS_IN_REMOTE
-#define CONFIG_ENV_ADDR		0xffe20000
-#define CONFIG_ENV_SIZE		0x2000
-#elif defined(CONFIG_ENV_IS_NOWHERE)
-#define CONFIG_ENV_SIZE		0x2000
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE		0x2000
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
-#endif
-
-#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk()
-#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk()
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
-#endif
-
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_SYS_CACHE_STASHING
 #define CONFIG_BTB			/* toggle branch predition */
-#define	CONFIG_DDR_ECC
 #ifdef CONFIG_DDR_ECC
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
@@ -129,14 +58,9 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_ENABLE_36BIT_PHYS
 
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_ADDR_MAP
 #define CONFIG_SYS_NUM_ADDR_MAP		64	/* number of TLB1 entries */
-#endif
 
-#if 0
-#define CONFIG_POST CONFIG_SYS_POST_MEMORY	/* test POST memory test */
-#endif
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 #define CONFIG_SYS_ALT_MEMTEST
@@ -147,17 +71,8 @@ unsigned long get_board_ddr_clk(void);
  */
 #define CONFIG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
 
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_DCSRBAR		0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
-#endif
-
-/* EEPROM */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM	0
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 
 /*
  * DDR Setup
@@ -174,199 +89,16 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_DDR_SPD
 #define CONFIG_FSL_DDR3
 
-#define CONFIG_SYS_SPD_BUS_NUM	0
-#define SPD_EEPROM_ADDRESS1	0x51
-#define SPD_EEPROM_ADDRESS2	0x52
-#define SPD_EEPROM_ADDRESS3	0x53
-#define SPD_EEPROM_ADDRESS4	0x54
-#define SPD_EEPROM_ADDRESS5	0x55
-#define SPD_EEPROM_ADDRESS6	0x56
-#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1	/* for p3041/p5010 */
-#define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
 
 /*
  * IFC Definitions
  */
 #define CONFIG_SYS_FLASH_BASE	0xe0000000
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
-#else
-#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
-#endif
-
-#define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
-#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
-				+ 0x8000000) | \
-				CSPR_PORT_SIZE_16 | \
-				CSPR_MSEL_NOR | \
-				CSPR_V)
-#define CONFIG_SYS_NOR1_CSPR_EXT	(0xf)
-#define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
-				CSPR_PORT_SIZE_16 | \
-				CSPR_MSEL_NOR | \
-				CSPR_V)
-#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
-/* NOR Flash Timing Params */
-#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
-
-#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
-				FTIM0_NOR_TEADC(0x5) | \
-				FTIM0_NOR_TEAHC(0x5))
-#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
-				FTIM1_NOR_TRAD_NOR(0x1A) |\
-				FTIM1_NOR_TSEQRAD_NOR(0x13))
-#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
-				FTIM2_NOR_TCH(0x4) | \
-				FTIM2_NOR_TWPH(0x0E) | \
-				FTIM2_NOR_TWP(0x1c))
-#define CONFIG_SYS_NOR_FTIM3	0x0
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS \
-					+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
-
-#define CONFIG_FSL_QIXIS	/* use common QIXIS code */
-#define QIXIS_BASE			0xffdf0000
-#define QIXIS_LBMAP_SWITCH		6
-#define QIXIS_LBMAP_MASK		0x0f
-#define QIXIS_LBMAP_SHIFT		0
-#define QIXIS_LBMAP_DFLTBANK		0x00
-#define QIXIS_LBMAP_ALTBANK		0x04
-#define QIXIS_RST_CTL_RESET		0x83
-#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
-#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
-#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
-#ifdef CONFIG_PHYS_64BIT
-#define QIXIS_BASE_PHYS		(0xf00000000ull | QIXIS_BASE)
-#else
-#define QIXIS_BASE_PHYS		QIXIS_BASE
-#endif
-
-#define CONFIG_SYS_CSPR3_EXT	(0xf)
-#define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
-				| CSPR_PORT_SIZE_8 \
-				| CSPR_MSEL_GPCM \
-				| CSPR_V)
-#define CONFIG_SYS_AMASK3	IFC_AMASK(4 * 1024)
-#define CONFIG_SYS_CSOR3	0x0
-/* QIXIS Timing parameters for IFC CS3 */
-#define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
-					FTIM0_GPCM_TEADC(0x0e) | \
-					FTIM0_GPCM_TEAHC(0x0e))
-#define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
-					FTIM1_GPCM_TRAD(0x3f))
-#define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
-					FTIM2_GPCM_TCH(0x0) | \
-					FTIM2_GPCM_TWP(0x1f))
-#define CONFIG_SYS_CS3_FTIM3		0x0
-
-/* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_BASE		0xff800000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
-#else
-#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
-#endif
 
-#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
-#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
-				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
-				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
-				| CSPR_V)
-#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
-
-#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
-				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
-				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
-				| CSOR_NAND_RAL_3	/* RAL = 2Byes */ \
-				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
-				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
-				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
-					FTIM0_NAND_TWP(0x18)   | \
-					FTIM0_NAND_TWCHT(0x07) | \
-					FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
-					FTIM1_NAND_TWBE(0x39)  | \
-					FTIM1_NAND_TRR(0x0e)   | \
-					FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
-					FTIM2_NAND_TREH(0x0a) | \
-					FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3		0x0
-
-#define CONFIG_SYS_NAND_DDR_LAW		11
-
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
-
-#if defined(CONFIG_NAND)
-#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
-#else
-#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
-#endif
-#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
-#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
-#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
 
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
 
-#if defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
 #define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
 #define CONFIG_MISC_INIT_R
 
@@ -376,18 +108,12 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_L1_INIT_RAM
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe0ec000
 /* The assembler doesn't like typecast */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#else
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS	0xfe0ec000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
-#endif
 #define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
 
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
@@ -431,149 +157,55 @@ unsigned long get_board_ddr_clk(void);
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	100000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x118000
-#define CONFIG_SYS_FSL_I2C2_SPEED	100000
 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x118100
 
-#define I2C_MUX_PCA_ADDR_PRI		0x77 /* I2C bus multiplexer,primary */
-#define I2C_MUX_PCA_ADDR_SEC		0x76 /* I2C bus multiplexer,secondary */
-
-#define I2C_MUX_CH_DEFAULT	0x8
-#define I2C_MUX_CH_VOL_MONITOR	0xa
-#define I2C_MUX_CH_VSC3316_FS	0xc
-#define I2C_MUX_CH_VSC3316_BS	0xd
-
-/* Voltage monitor on channel 2*/
-#define I2C_VOL_MONITOR_ADDR		0x40
-#define I2C_VOL_MONITOR_BUS_V_OFFSET	0x2
-#define I2C_VOL_MONITOR_BUS_V_OVF	0x1
-#define I2C_VOL_MONITOR_BUS_V_SHIFT	3
-
-/* VSC Crossbar switches */
-#define CONFIG_VSC_CROSSBAR
-#define VSC3316_FSM_TX_ADDR	0x70
-#define VSC3316_FSM_RX_ADDR	0x71
-
 /*
  * RapidIO
  */
 #define CONFIG_SYS_SRIO1_MEM_VIRT	0xa0000000
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_SRIO1_MEM_PHYS	0xc20000000ull
-#else
-#define CONFIG_SYS_SRIO1_MEM_PHYS	0xa0000000
-#endif
 #define CONFIG_SYS_SRIO1_MEM_SIZE	0x10000000	/* 256M */
 
 #define CONFIG_SYS_SRIO2_MEM_VIRT	0xb0000000
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_SRIO2_MEM_PHYS	0xc30000000ull
-#else
-#define CONFIG_SYS_SRIO2_MEM_PHYS	0xb0000000
-#endif
 #define CONFIG_SYS_SRIO2_MEM_SIZE	0x10000000	/* 256M */
 
 /*
- * for slave u-boot IMAGE instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000	/* 512K */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
-/*
- * for slave UCODE and ENV instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000	/* 256K */
-
-/* slave core release by master*/
-#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
-#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
-
-/*
- * SRIO_PCIE_BOOT - SLAVE
- */
-#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
-		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
-#endif
-/*
- * eSPI - Enhanced SPI
- */
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED         10000000
-#define CONFIG_SF_DEFAULT_MODE          0
-
-/*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 
 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 #define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
-#else
-#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0x80000000
-#endif
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
-#else
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xf8000000
-#endif
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 #define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
-#else
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
-#endif
 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
-#else
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xf8010000
-#endif
 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 #define CONFIG_SYS_PCIE3_MEM_VIRT	0xc0000000
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE3_MEM_PHYS	0xc40000000ull
-#else
-#define CONFIG_SYS_PCIE3_MEM_BUS	0xc0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc0000000
-#endif
 #define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
 #define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
-#else
-#define CONFIG_SYS_PCIE3_IO_PHYS	0xf8020000
-#endif
 #define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 4, Base address 203000 */
@@ -584,84 +216,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull
 #define CONFIG_SYS_PCIE4_IO_SIZE	0x00010000	/* 64k */
 
-/* Qman/Bman */
-#ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
-#define CONFIG_SYS_BMAN_NUM_PORTALS	50
-#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
-#else
-#define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
-#endif
-#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
-#define CONFIG_SYS_QMAN_NUM_PORTALS	50
-#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
-#else
-#define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
-#endif
-#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
-
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_SYS_DPAA_PME
-#define CONFIG_SYS_PMAN
-#define CONFIG_SYS_DPAA_DCE
-#define CONFIG_SYS_INTERLAKEN
-
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 545KB (1089 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
- */
-#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-/*
- * Slave has no ucode locally, it can fetch this from remote. When implementing
- * in two corenet boards, slave's ucode could be stored in master's memory
- * space, the address can be mapped from slave TLB->slave LAW->
- * slave SRIO or PCIE outbound window->master inbound window->
- * master LAW->the ucode address in master's memory space.
- */
-#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
-#else
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF40000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
-#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-#endif /* CONFIG_NOBQFMAN */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHYLIB_10G
-#define CONFIG_PHY_VITESSE
-#define CONFIG_PHY_TERANETICS
-#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
-#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
-#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
-#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
-#define FM1_10GEC1_PHY_ADDR	0x0
-#define FM1_10GEC2_PHY_ADDR	0x1
-#define FM2_10GEC1_PHY_ADDR	0x2
-#define FM2_10GEC2_PHY_ADDR	0x3
-#endif
-
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_NET_MULTI
@@ -724,30 +278,6 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 /*
-* USB
-*/
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_CMD_EXT2
-#define CONFIG_HAS_FSL_DR_USB
-
-#define CONFIG_MMC
-
-#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
@@ -788,112 +318,11 @@ unsigned long get_board_ddr_clk(void);
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR		1000000
 
-#define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */
 
 #define CONFIG_BAUDRATE	115200
 
-#define __USB_PHY_TYPE	utmi
-
-/*
- * T4240 has 3 DDR controllers. Default to 3way_4KB interleaving. It can be
- * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to
- * cacheline interleaving. It can be cacheline, page, bank, superbank.
- * See doc/README.fsl-ddr for details.
- */
-#ifdef CONFIG_PPC_T4240
-#define CTRL_INTLV_PREFERED 3way_4KB
-#else
-#define CTRL_INTLV_PREFERED cacheline
-#endif
-
-#define	CONFIG_EXTRA_ENV_SETTINGS				\
-	"hwconfig=fsl_ddr:"					\
-	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","	\
-	"bank_intlv=auto;"					\
-	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
-	"netdev=eth0\0"						\
-	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
-	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"		\
-	"tftpflash=tftpboot $loadaddr $uboot && "		\
-	"protect off $ubootaddr +$filesize && "			\
-	"erase $ubootaddr +$filesize && "			\
-	"cp.b $loadaddr $ubootaddr $filesize && "		\
-	"protect on $ubootaddr +$filesize && "			\
-	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
-	"consoledev=ttyS0\0"					\
-	"ramdiskaddr=2000000\0"					\
-	"ramdiskfile=t4240qds/ramdisk.uboot\0"			\
-	"fdtaddr=c00000\0"					\
-	"fdtfile=t4240qds/t4240qds.dtb\0"				\
-	"bdev=sda3\0"						\
-	"c=ffe\0"
-
-/* For emulation this causes u-boot to jump to the start of the proof point
-   app code automatically */
-#define CONFIG_PROOF_POINTS			\
- "setenv bootargs root=/dev/$bdev rw "		\
- "console=$consoledev,$baudrate $othbootargs;"	\
- "cpu 1 release 0x29000000 - - -;"		\
- "cpu 2 release 0x29000000 - - -;"		\
- "cpu 3 release 0x29000000 - - -;"		\
- "cpu 4 release 0x29000000 - - -;"		\
- "cpu 5 release 0x29000000 - - -;"		\
- "cpu 6 release 0x29000000 - - -;"		\
- "cpu 7 release 0x29000000 - - -;"		\
- "go 0x29000000"
-
 #define CONFIG_HVBOOT				\
  "setenv bootargs config-addr=0x60000000; "	\
  "bootm 0x01000000 - 0x00f00000"
 
-#define CONFIG_ALU				\
- "setenv bootargs root=/dev/$bdev rw "		\
- "console=$consoledev,$baudrate $othbootargs;"	\
- "cpu 1 release 0x01000000 - - -;"		\
- "cpu 2 release 0x01000000 - - -;"		\
- "cpu 3 release 0x01000000 - - -;"		\
- "cpu 4 release 0x01000000 - - -;"		\
- "cpu 5 release 0x01000000 - - -;"		\
- "cpu 6 release 0x01000000 - - -;"		\
- "cpu 7 release 0x01000000 - - -;"		\
- "go 0x01000000"
-
-#define CONFIG_LINUX				\
- "setenv bootargs root=/dev/ram rw "		\
- "console=$consoledev,$baudrate $othbootargs;"	\
- "setenv ramdiskaddr 0x02000000;"		\
- "setenv fdtaddr 0x00c00000;"			\
- "setenv loadaddr 0x1000000;"			\
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_HDBOOT					\
-	"setenv bootargs root=/dev/$bdev rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND			\
-	"setenv bootargs root=/dev/nfs rw "	\
-	"nfsroot=$serverip:$rootpath "		\
-	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"		\
-	"tftp $fdtaddr $fdtfile;"		\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND				\
-	"setenv bootargs root=/dev/ram rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $ramdiskaddr $ramdiskfile;"		\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND		CONFIG_LINUX
-
-#ifdef CONFIG_SECURE_BOOT
-#include <asm/fsl_secure_boot.h>
-#endif
-
 #endif	/* __CONFIG_H */

include/pci.h

@@ -410,13 +410,6 @@
 #define PCI_MAX_PCI_DEVICES	32
 #define PCI_MAX_PCI_FUNCTIONS	8
 
-#define PCI_DCR		0x54    /* PCIe Device Control Register */
-#define PCI_DSR		0x56    /* PCIe Device Status Register */
-#define PCI_LSR		0x5e    /* PCIe Link Status Register */
-#define PCI_LCR		0x5c    /* PCIe Link Control Register */
-#define PCI_LTSSM	0x404   /* PCIe Link Training, Status State Machine */
-#define  PCI_LTSSM_L0	0x16    /* L0 state */
-
 /* Include the ID list */
 
 #include <pci_ids.h>