Add the DTS documentation for the Micrel KSZ90x1 binding. The original document was from: [commit 4b405efbe12de28b26289282b431323d73992381 from the Linux kernel] This takes the original document and adds a clarification on how the skew values are represented in the code. References: Micrel ksz9021rl/rn Data Sheet, Revision 1.2. Dated 2/13/2014. http://www.micrel.com/_PDF/Ethernet/datasheets/ksz9021rl-rn_ds.pdf Micrel ksz9031rnx Data Sheet, Revision 2.1. Dated 11/20/2014. http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>master
parent
1f9e672c79
commit
c16e69f702
@ -0,0 +1,165 @@ |
||||
Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY |
||||
|
||||
Some boards require special tuning values, particularly when it comes to |
||||
clock delays. You can specify clock delay values by adding |
||||
micrel-specific properties to an Ethernet OF device node. |
||||
|
||||
Note that these settings are applied after any phy-specific fixup from |
||||
phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c), |
||||
and therefore may overwrite them. |
||||
|
||||
KSZ9021: |
||||
|
||||
All skew control options are specified in picoseconds. The minimum |
||||
value is 0, the maximum value is 1800, and it is incremented by 120ps |
||||
steps. |
||||
|
||||
Optional properties: |
||||
|
||||
- rxc-skew-ps : Skew control of RXC pad |
||||
- rxdv-skew-ps : Skew control of RX CTL pad |
||||
- txc-skew-ps : Skew control of TXC pad |
||||
- txen-skew-ps : Skew control of TX CTL pad |
||||
- rxd0-skew-ps : Skew control of RX data 0 pad |
||||
- rxd1-skew-ps : Skew control of RX data 1 pad |
||||
- rxd2-skew-ps : Skew control of RX data 2 pad |
||||
- rxd3-skew-ps : Skew control of RX data 3 pad |
||||
- txd0-skew-ps : Skew control of TX data 0 pad |
||||
- txd1-skew-ps : Skew control of TX data 1 pad |
||||
- txd2-skew-ps : Skew control of TX data 2 pad |
||||
- txd3-skew-ps : Skew control of TX data 3 pad |
||||
|
||||
KSZ9031: |
||||
|
||||
All skew control options are specified in picoseconds. The minimum |
||||
value is 0, and the maximum is property-dependent. The increment |
||||
step is 60ps. |
||||
|
||||
The KSZ9031 hardware supports a range of skew values from negative to |
||||
positive, where the specific range is property dependent. All values |
||||
specified in the devicetree are offset by the minimum value so they |
||||
can be represented as positive integers in the devicetree since it's |
||||
difficult to represent a negative number in the devictree. |
||||
|
||||
The following 5-bit values table apply to rxc-skew-ps and txc-skew-ps. |
||||
|
||||
Pad Skew Value Delay (ps) Devicetree Value |
||||
------------------------------------------------------ |
||||
0_0000 -900ps 0 |
||||
0_0001 -840ps 60 |
||||
0_0010 -780ps 120 |
||||
0_0011 -720ps 180 |
||||
0_0100 -660ps 240 |
||||
0_0101 -600ps 300 |
||||
0_0110 -540ps 360 |
||||
0_0111 -480ps 420 |
||||
0_1000 -420ps 480 |
||||
0_1001 -360ps 540 |
||||
0_1010 -300ps 600 |
||||
0_1011 -240ps 660 |
||||
0_1100 -180ps 720 |
||||
0_1101 -120ps 780 |
||||
0_1110 -60ps 840 |
||||
0_1111 0ps 900 |
||||
1_0000 60ps 960 |
||||
1_0001 120ps 1020 |
||||
1_0010 180ps 1080 |
||||
1_0011 240ps 1140 |
||||
1_0100 300ps 1200 |
||||
1_0101 360ps 1260 |
||||
1_0110 420ps 1320 |
||||
1_0111 480ps 1380 |
||||
1_1000 540ps 1440 |
||||
1_1001 600ps 1500 |
||||
1_1010 660ps 1560 |
||||
1_1011 720ps 1620 |
||||
1_1100 780ps 1680 |
||||
1_1101 840ps 1740 |
||||
1_1110 900ps 1800 |
||||
1_1111 960ps 1860 |
||||
|
||||
The following 4-bit values table apply to the txdX-skew-ps, rxdX-skew-ps |
||||
data pads, and the rxdv-skew-ps, txen-skew-ps control pads. |
||||
|
||||
Pad Skew Value Delay (ps) Devicetree Value |
||||
------------------------------------------------------ |
||||
0000 -420ps 0 |
||||
0001 -360ps 60 |
||||
0010 -300ps 120 |
||||
0011 -240ps 180 |
||||
0100 -180ps 240 |
||||
0101 -120ps 300 |
||||
0110 -60ps 360 |
||||
0111 0ps 420 |
||||
1000 60ps 480 |
||||
1001 120ps 540 |
||||
1010 180ps 600 |
||||
1011 240ps 660 |
||||
1100 300ps 720 |
||||
1101 360ps 780 |
||||
1110 420ps 840 |
||||
1111 480ps 900 |
||||
|
||||
Optional properties: |
||||
|
||||
Maximum value of 1860: |
||||
|
||||
- rxc-skew-ps : Skew control of RX clock pad |
||||
- txc-skew-ps : Skew control of TX clock pad |
||||
|
||||
Maximum value of 900: |
||||
|
||||
- rxdv-skew-ps : Skew control of RX CTL pad |
||||
- txen-skew-ps : Skew control of TX CTL pad |
||||
- rxd0-skew-ps : Skew control of RX data 0 pad |
||||
- rxd1-skew-ps : Skew control of RX data 1 pad |
||||
- rxd2-skew-ps : Skew control of RX data 2 pad |
||||
- rxd3-skew-ps : Skew control of RX data 3 pad |
||||
- txd0-skew-ps : Skew control of TX data 0 pad |
||||
- txd1-skew-ps : Skew control of TX data 1 pad |
||||
- txd2-skew-ps : Skew control of TX data 2 pad |
||||
- txd3-skew-ps : Skew control of TX data 3 pad |
||||
|
||||
Examples: |
||||
|
||||
/* Attach to an Ethernet device with autodetected PHY */ |
||||
&enet { |
||||
rxc-skew-ps = <1800>; |
||||
rxdv-skew-ps = <0>; |
||||
txc-skew-ps = <1800>; |
||||
txen-skew-ps = <0>; |
||||
status = "okay"; |
||||
}; |
||||
|
||||
/* Attach to an explicitly-specified PHY */ |
||||
mdio { |
||||
phy0: ethernet-phy@0 { |
||||
rxc-skew-ps = <1800>; |
||||
rxdv-skew-ps = <0>; |
||||
txc-skew-ps = <1800>; |
||||
txen-skew-ps = <0>; |
||||
reg = <0>; |
||||
}; |
||||
}; |
||||
ethernet@70000 { |
||||
status = "okay"; |
||||
phy = <&phy0>; |
||||
phy-mode = "rgmii-id"; |
||||
}; |
||||
|
||||
References |
||||
|
||||
Micrel ksz9021rl/rn Data Sheet, Revision 1.2. Dated 2/13/2014. |
||||
http://www.micrel.com/_PDF/Ethernet/datasheets/ksz9021rl-rn_ds.pdf |
||||
|
||||
Micrel ksz9031rnx Data Sheet, Revision 2.1. Dated 11/20/2014. |
||||
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf |
||||
|
||||
Notes: |
||||
|
||||
Note that a previous version of the Micrel ksz9021rl/rn Data Sheet |
||||
was missing extended register 106 (transmit data pad skews), and |
||||
incorrectly specified the ps per step as 200ps/step instead of |
||||
120ps/step. The latest update to this document reflects the latest |
||||
revision of the Micrel specification even though usage in the kernel |
||||
still reflects that incorrect document. |
Loading…
Reference in new issue